diff options
| -rw-r--r-- | keyboards/waldo/config.h | 19 | ||||
| -rw-r--r-- | keyboards/waldo/rules.mk | 33 |
2 files changed, 11 insertions, 41 deletions
diff --git a/keyboards/waldo/config.h b/keyboards/waldo/config.h index c913ae771..c3272bf1d 100644 --- a/keyboards/waldo/config.h +++ b/keyboards/waldo/config.h @@ -36,16 +36,12 @@ along with this program. If not, see <http://www.gnu.org/licenses/>. #define UNUSED_PINS #define BACKLIGHT_PIN B7 +#define BACKLIGHT_BREATHING +#define BACKLIGHT_LEVELS 3 /* COL2ROW or ROW2COL */ #define DIODE_DIRECTION COL2ROW -/* define if matrix has ghost */ -//#define MATRIX_HAS_GHOST - -/* number of backlight levels */ -#define BACKLIGHT_LEVELS 3 - /* Set 0 if debouncing isn't needed */ #define DEBOUNCE 5 @@ -73,5 +69,12 @@ along with this program. If not, see <http://www.gnu.org/licenses/>. //#define NO_ACTION_FUNCTION // RGB LED -#define RGB_DI_PIN B0 // The pin the LED strip is connected to -#define RGBLED_NUM 10 // Number of LEDs in your strip +#define RGB_DI_PIN B0 +#ifdef RGB_DI_PIN +#define RGBLIGHT_ANIMATIONS +#define RGBLED_NUM 10 +#define RGBLIGHT_HUE_STEP 8 +#define RGBLIGHT_SAT_STEP 8 +#define RGBLIGHT_VAL_STEP 8 +#define RGBLIGHT_SLEEP +#endif
\ No newline at end of file diff --git a/keyboards/waldo/rules.mk b/keyboards/waldo/rules.mk index 40ac48474..6b3a9b96c 100644 --- a/keyboards/waldo/rules.mk +++ b/keyboards/waldo/rules.mk @@ -1,45 +1,12 @@ # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - # Bootloader # This definition is optional, and if your keyboard supports multiple bootloaders of # different sizes, comment this out, and the correct address will be loaded # automatically (+60). See bootloader.mk for all options. BOOTLOADER = atmel-dfu - # Interrupt driven control endpoint task(+60) OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT |