diff options
| -rw-r--r-- | common_features.mk | 21 | ||||
| -rw-r--r-- | docs/feature_backlight.md | 131 | ||||
| -rw-r--r-- | quantum/backlight/backlight_avr.c | 10 | ||||
| -rw-r--r-- | quantum/backlight/backlight_soft.c | 66 | ||||
| -rw-r--r-- | quantum/quantum.c | 2 | ||||
| -rw-r--r-- | quantum/quantum.h | 4 |
6 files changed, 173 insertions, 61 deletions
diff --git a/common_features.mk b/common_features.mk index 7bb9187bb..a1f95955a 100644 --- a/common_features.mk +++ b/common_features.mk @@ -234,7 +234,7 @@ ifeq ($(strip $(BACKLIGHT_CUSTOM_DRIVER)), yes) BACKLIGHT_ENABLE = custom endif -VALID_BACKLIGHT_TYPES := yes custom +VALID_BACKLIGHT_TYPES := yes software custom BACKLIGHT_ENABLE ?= no ifneq ($(strip $(BACKLIGHT_ENABLE)), no) @@ -246,19 +246,22 @@ ifneq ($(strip $(BACKLIGHT_ENABLE)), no) CIE1931_CURVE = yes endif - COMMON_VPATH += $(QUANTUM_DIR)/backlight SRC += $(QUANTUM_DIR)/backlight/backlight.c OPT_DEFS += -DBACKLIGHT_ENABLE - ifeq ($(strip $(BACKLIGHT_ENABLE)), custom) - OPT_DEFS += -DBACKLIGHT_CUSTOM_DRIVER - endif - - ifeq ($(PLATFORM),AVR) - SRC += $(QUANTUM_DIR)/backlight/backlight_avr.c + ifeq ($(strip $(BACKLIGHT_ENABLE)), software) + SRC += $(QUANTUM_DIR)/backlight/backlight_soft.c else - SRC += $(QUANTUM_DIR)/backlight/backlight_arm.c + ifeq ($(strip $(BACKLIGHT_ENABLE)), custom) + OPT_DEFS += -DBACKLIGHT_CUSTOM_DRIVER + endif + + ifeq ($(PLATFORM),AVR) + SRC += $(QUANTUM_DIR)/backlight/backlight_avr.c + else + SRC += $(QUANTUM_DIR)/backlight/backlight_arm.c + endif endif endif diff --git a/docs/feature_backlight.md b/docs/feature_backlight.md index 6a2946fd6..71f375594 100644 --- a/docs/feature_backlight.md +++ b/docs/feature_backlight.md @@ -6,14 +6,16 @@ QMK is able to control the brightness of these LEDs by switching them on and off The MCU can only supply so much current to its GPIO pins. Instead of powering the backlight directly from the MCU, the backlight pin is connected to a transistor or MOSFET that switches the power to the LEDs. -## Usage +## Driver configuration Most keyboards have backlighting enabled by default if they support it, but if it is not working for you, check that your `rules.mk` includes the following: -```make -BACKLIGHT_ENABLE = yes +```makefile +BACKLIGHT_ENABLE = software # Valid driver values are 'yes,software,no' ``` +See below for help on individual drivers. + ## Keycodes Once enabled the following keycodes below can be used to change the backlight level. @@ -27,8 +29,54 @@ Once enabled the following keycodes below can be used to change the backlight le |`BL_DEC` |Decrease the backlight level | |`BL_BRTG`|Toggle backlight breathing | +## Backlight Functions + +|Function |Description | +|----------|-----------------------------------------------------------| +|`backlight_toggle()` |Turn the backlight on or off | +|`backlight_enable()` |Turn the backlight on | +|`backlight_disable()` |Turn the backlight off | +|`backlight_step()` |Cycle through backlight levels | +|`backlight_increase()` |Increase the backlight level | +|`backlight_decrease()` |Decrease the backlight level | +|`backlight_level(x)` |Sets the backlight level to specified level | +|`get_backlight_level()` |Return the current backlight level | +|`is_backlight_enabled()`|Return whether the backlight is currently on | + +### Backlight Breathing Functions + +|Function |Description | +|----------|---------------------------------------------------| +|`breathing_toggle()` |Turn the backlight breathing on or off | +|`breathing_enable()` |Turns on backlight breathing | +|`breathing_disable()` |Turns off backlight breathing | + +## Common Driver Configuration + +To change the behavior of the backlighting, `#define` these in your `config.h`: + +|Define |Default |Description | +|---------------------|-------------|--------------------------------------------------------------------------------------| +|`BACKLIGHT_LEVELS` |`3` |The number of brightness levels (maximum 31 excluding off) | +|`BACKLIGHT_CAPS_LOCK`|*Not defined*|Enable Caps Lock indicator using backlight (for keyboards without dedicated LED) | +|`BACKLIGHT_BREATHING`|*Not defined*|Enable backlight breathing, if supported | +|`BREATHING_PERIOD` |`6` |The length of one backlight "breath" in seconds | +|`BACKLIGHT_ON_STATE` |`0` |The state of the backlight pin when the backlight is "on" - `1` for high, `0` for low | + +### Backlight On State + +Most backlight circuits are driven by an N-channel MOSFET or NPN transistor. This means that to turn the transistor *on* and light the LEDs, you must drive the backlight pin, connected to the gate or base, *high*. +Sometimes, however, a P-channel MOSFET, or a PNP transistor is used. In this case, when the transistor is on, the pin is driven *low* instead. + +This functionality is configured at the keyboard level with the `BACKLIGHT_ON_STATE` define. + ## AVR driver +On AVR boards, the default driver currently sniffs the configuration to pick the best scenario. To enable it, add this to your rules.mk: +```makefile +BACKLIGHT_ENABLE = yes +``` + ### Caveats Hardware PWM is supported according to the following table: @@ -63,22 +111,10 @@ When both timers are in use for Audio, the backlight PWM will not use a hardware To change the behavior of the backlighting, `#define` these in your `config.h`: -|Define |Default |Description | -|---------------------|-------------|-------------------------------------------------------------------------------------------------------------| -|`BACKLIGHT_PIN` |`B7` |The pin that controls the LEDs. Unless you are designing your own keyboard, you shouldn't need to change this| -|`BACKLIGHT_PINS` |*Not defined*|experimental: see below for more information | -|`BACKLIGHT_LEVELS` |`3` |The number of brightness levels (maximum 31 excluding off) | -|`BACKLIGHT_CAPS_LOCK`|*Not defined*|Enable Caps Lock indicator using backlight (for keyboards without dedicated LED) | -|`BACKLIGHT_BREATHING`|*Not defined*|Enable backlight breathing, if supported | -|`BREATHING_PERIOD` |`6` |The length of one backlight "breath" in seconds | -|`BACKLIGHT_ON_STATE` |`0` |The state of the backlight pin when the backlight is "on" - `1` for high, `0` for low | - -### Backlight On State - -Most backlight circuits are driven by an N-channel MOSFET or NPN transistor. This means that to turn the transistor *on* and light the LEDs, you must drive the backlight pin, connected to the gate or base, *high*. -Sometimes, however, a P-channel MOSFET, or a PNP transistor is used. In this case, when the transistor is on, the pin is driven *low* instead. - -This functionality is configured at the keyboard level with the `BACKLIGHT_ON_STATE` define. +|Define |Default |Description | +|---------------------|-------------|--------------------------------------------------------------------------------------------------------------| +|`BACKLIGHT_PIN` |`B7` |The pin that controls the LEDs. Unless you are designing your own keyboard, you shouldn't need to change this | +|`BACKLIGHT_PINS` |*Not defined*|experimental: see below for more information | ### Multiple backlight pins @@ -103,7 +139,7 @@ In this way `OCRxx` essentially controls the duty cycle of the LEDs, and thus th The breathing effect is achieved by registering an interrupt handler for `TIMER1_OVF_vect` that is called whenever the counter resets, roughly 244 times per second. In this handler, the value of an incrementing counter is mapped onto a precomputed brightness curve. To turn off breathing, the interrupt handler is simply disabled, and the brightness reset to the level stored in EEPROM. -### Software PWM Implementation +### Timer Assisted PWM Implementation When `BACKLIGHT_PIN` is not set to a hardware backlight pin, QMK will use a hardware timer configured to trigger software interrupts. This time will count up to `ICRx` (by default `0xFFFF`) before resetting to 0. When resetting to 0, the CPU will fire an OVF (overflow) interrupt that will turn the LEDs on, starting the duty cycle. @@ -114,9 +150,14 @@ The breathing effect is the same as in the hardware PWM implementation. ## ARM Driver +While still in its early stages, ARM backlight support aims to eventually have feature parity with AVR. To enable it, add this to your rules.mk: +```makefile +BACKLIGHT_ENABLE = yes +``` + ### Caveats -Currently only hardware PWM is supported, and does not provide automatic configuration. +Currently only hardware PWM is supported, not timer assisted, and does not provide automatic configuration. ?> STMF072 support is being investigated. @@ -130,30 +171,32 @@ To change the behavior of the backlighting, `#define` these in your `config.h`: |`BACKLIGHT_PWM_DRIVER` |`PWMD4` |The PWM driver to use, see ST datasheets for pin to PWM timer mapping. Unless you are designing your own keyboard, you shouldn't need to change this| |`BACKLIGHT_PWM_CHANNEL` |`3` |The PWM channel to use, see ST datasheets for pin to PWM channel mapping. Unless you are designing your own keyboard, you shouldn't need to change this| |`BACKLIGHT_PAL_MODE` |`2` |The pin alternative function to use, see ST datasheets for pin AF mapping. Unless you are designing your own keyboard, you shouldn't need to change this| -|`BACKLIGHT_LEVELS` |`3` |The number of brightness levels (maximum 31 excluding off) | -|`BACKLIGHT_CAPS_LOCK` |*Not defined*|Enable Caps Lock indicator using backlight (for keyboards without dedicated LED) | -|`BACKLIGHT_BREATHING` |*Not defined*|Enable backlight breathing, if supported | -|`BREATHING_PERIOD` |`6` |The length of one backlight "breath" in seconds | -## Backlight Functions +## Software PWM Driver -|Function |Description | -|----------|-----------------------------------------------------------| -|`backlight_toggle()` |Turn the backlight on or off | -|`backlight_enable()` |Turn the backlight on | -|`backlight_disable()` |Turn the backlight off | -|`backlight_step()` |Cycle through backlight levels | -|`backlight_increase()` |Increase the backlight level | -|`backlight_decrease()` |Decrease the backlight level | -|`backlight_level(x)` |Sets the backlight level, from 0 to | -| |`BACKLIGHT_LEVELS` | -|`get_backlight_level()` |Return the current backlight level | -|`is_backlight_enabled()`|Return whether the backlight is currently on | +Emulation of PWM while running other keyboard tasks, it offers maximum hardware compatibility without extra platform configuration. The tradeoff is the backlight might jitter when the keyboard is busy. To enable, add this to your rules.mk: +```makefile +BACKLIGHT_ENABLE = software +``` -### Backlight Breathing Functions +### Software PWM Configuration + +To change the behavior of the backlighting, `#define` these in your `config.h`: + +|Define |Default |Description | +|-----------------|-------------|-------------------------------------------------------------------------------------------------------------| +|`BACKLIGHT_PIN` |`B7` |The pin that controls the LEDs. Unless you are designing your own keyboard, you shouldn't need to change this| +|`BACKLIGHT_PINS` |*Not defined*|experimental: see below for more information | -|Function |Description | -|----------|----------------------------------------------------------| -|`breathing_toggle()` |Turn the backlight breathing on or off | -|`breathing_enable()` |Turns on backlight breathing | -|`breathing_disable()` |Turns off backlight breathing | +### Multiple backlight pins + +Most keyboards have only one backlight pin which control all backlight LEDs (especially if the backlight is connected to an hardware PWM pin). +In software PWM, it is possible to define multiple backlight pins. All those pins will be turned on and off at the same time during the PWM duty cycle. +This feature allows to set for instance the Caps Lock LED (or any other controllable LED) brightness at the same level as the other LEDs of the backlight. This is useful if you have mapped LCTRL in place of Caps Lock and you need the Caps Lock LED to be part of the backlight instead of being activated when Caps Lock is on. + +To activate multiple backlight pins, you need to add something like this to your user `config.h`: + +```c +#undef BACKLIGHT_PIN +#define BACKLIGHT_PINS { F5, B2 } +``` diff --git a/quantum/backlight/backlight_avr.c b/quantum/backlight/backlight_avr.c index 445698f47..648a37adf 100644 --- a/quantum/backlight/backlight_avr.c +++ b/quantum/backlight/backlight_avr.c @@ -159,7 +159,7 @@ # define BACKLIGHT_ON_STATE 0 # endif -void backlight_on(uint8_t backlight_pin) { +void backlight_on(pin_t backlight_pin) { # if BACKLIGHT_ON_STATE == 0 writePinLow(backlight_pin); # else @@ -167,7 +167,7 @@ void backlight_on(uint8_t backlight_pin) { # endif } -void backlight_off(uint8_t backlight_pin) { +void backlight_off(pin_t backlight_pin) { # if BACKLIGHT_ON_STATE == 0 writePinHigh(backlight_pin); # else @@ -191,16 +191,16 @@ void backlight_off(uint8_t backlight_pin) { # define FOR_EACH_LED(x) \ for (uint8_t i = 0; i < BACKLIGHT_LED_COUNT; i++) { \ - uint8_t backlight_pin = backlight_pins[i]; \ + pin_t backlight_pin = backlight_pins[i]; \ { x } \ } -static const uint8_t backlight_pins[BACKLIGHT_LED_COUNT] = BACKLIGHT_PIN_INIT; +static const pin_t backlight_pins[BACKLIGHT_LED_COUNT] = BACKLIGHT_PIN_INIT; # else // full hardware PWM // we support only one backlight pin -static const uint8_t backlight_pin = BACKLIGHT_PIN; +static const pin_t backlight_pin = BACKLIGHT_PIN; # define FOR_EACH_LED(x) x # endif diff --git a/quantum/backlight/backlight_soft.c b/quantum/backlight/backlight_soft.c new file mode 100644 index 000000000..a6aba7782 --- /dev/null +++ b/quantum/backlight/backlight_soft.c @@ -0,0 +1,66 @@ +#include "quantum.h" +#include "backlight.h" + +#if !defined(BACKLIGHT_PIN) && !defined(BACKLIGHT_PINS) +# error "Backlight pin/pins not defined. Please configure." +#endif + +#ifdef BACKLIGHT_BREATHING +# error "Backlight breathing is not available for software PWM. Please disable." +#endif + +#ifndef BACKLIGHT_ON_STATE +# define BACKLIGHT_ON_STATE 0 +#endif + +#ifdef BACKLIGHT_PINS +# define BACKLIGHT_PIN_INIT BACKLIGHT_PINS +#else +# define BACKLIGHT_PIN_INIT \ + { BACKLIGHT_PIN } +#endif + +static const pin_t backlight_pins[] = BACKLIGHT_PIN_INIT; +#define BACKLIGHT_LED_COUNT (sizeof(backlight_pins) / sizeof(pin_t)) + +#define FOR_EACH_LED(x) \ + for (uint8_t i = 0; i < BACKLIGHT_LED_COUNT; i++) { \ + pin_t backlight_pin = backlight_pins[i]; \ + { x } \ + } + +void backlight_on(pin_t backlight_pin) { +#if BACKLIGHT_ON_STATE == 0 + writePinLow(backlight_pin); +#else + writePinHigh(backlight_pin); +#endif +} + +void backlight_off(pin_t backlight_pin) { +#if BACKLIGHT_ON_STATE == 0 + writePinHigh(backlight_pin); +#else + writePinLow(backlight_pin); +#endif +} + +void backlight_init_ports(void) { + // Setup backlight pin as output and output to on state. + FOR_EACH_LED(setPinOutput(backlight_pin); backlight_on(backlight_pin);) +} + +void backlight_task(void) { + static uint8_t backlight_tick = 0; + + if ((0xFFFF >> (get_backlight_level() * ((BACKLIGHT_LEVELS + 1) / 2))) & (1 << backlight_tick)) { + FOR_EACH_LED(backlight_on(backlight_pin);) + } else { + FOR_EACH_LED(backlight_off(backlight_pin);) + } + backlight_tick = (backlight_tick + 1) % 16; +} + +void backlight_set(uint8_t level) { + // noop as backlight_task uses get_backlight_level() +} diff --git a/quantum/quantum.c b/quantum/quantum.c index d689a9fbf..571dda4c5 100644 --- a/quantum/quantum.c +++ b/quantum/quantum.c @@ -981,7 +981,7 @@ void matrix_scan_quantum() { #if defined(BACKLIGHT_ENABLE) # if defined(LED_MATRIX_ENABLE) led_matrix_task(); -# elif defined(BACKLIGHT_PIN) +# elif defined(BACKLIGHT_PIN) || defined(BACKLIGHT_PINS) backlight_task(); # endif #endif diff --git a/quantum/quantum.h b/quantum/quantum.h index f5ac97379..01abe1c0a 100644 --- a/quantum/quantum.h +++ b/quantum/quantum.h @@ -257,8 +257,8 @@ void tap_code16(uint16_t code); void backlight_init_ports(void); void backlight_task(void); void backlight_task_internal(void); -void backlight_on(uint8_t backlight_pin); -void backlight_off(uint8_t backlight_pin); +void backlight_on(pin_t backlight_pin); +void backlight_off(pin_t backlight_pin); # ifdef BACKLIGHT_BREATHING void breathing_task(void); |