diff options
Diffstat (limited to 'keyboards/handwired')
195 files changed, 11709 insertions, 229 deletions
diff --git a/keyboards/handwired/108key_trackpoint/config.h b/keyboards/handwired/108key_trackpoint/config.h index a773a72b1..2c0662c0b 100644 --- a/keyboards/handwired/108key_trackpoint/config.h +++ b/keyboards/handwired/108key_trackpoint/config.h @@ -61,7 +61,7 @@ /* COL2ROW or ROW2COL */ #define DIODE_DIRECTION COL2ROW -#define DEBOUNCING_DELAY 5 +#define DEBOUNCE 5 #define LOCKING_SUPPORT_ENABLE #define LOCKING_RESYNC_ENABLE diff --git a/keyboards/handwired/412_64/config.h b/keyboards/handwired/412_64/config.h index 9cdb3fac8..cce38f3e6 100644 --- a/keyboards/handwired/412_64/config.h +++ b/keyboards/handwired/412_64/config.h @@ -38,7 +38,7 @@ // #define BACKLIGHT_LEVELS 3 /* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */ -#define DEBOUNCING_DELAY 5 +#define DEBOUNCE 5 /* define if matrix has ghost (lacks anti-ghosting diodes) */ //#define MATRIX_HAS_GHOST diff --git a/keyboards/handwired/arrow_pad/config.h b/keyboards/handwired/arrow_pad/config.h index 1ae3d21c4..abb600c51 100644 --- a/keyboards/handwired/arrow_pad/config.h +++ b/keyboards/handwired/arrow_pad/config.h @@ -52,7 +52,7 @@ along with this program. If not, see <http://www.gnu.org/licenses/>. #define DIODE_DIRECTION ROW2COL /* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */ -#define DEBOUNCING_DELAY 5 +#define DEBOUNCE 5 /* define if matrix has ghost (lacks anti-ghosting diodes) */ //#define MATRIX_HAS_GHOST diff --git a/keyboards/handwired/arrow_pad/keymaps/pad_21/config.h b/keyboards/handwired/arrow_pad/keymaps/pad_21/config.h index 9b6ecfaa3..0e471527d 100644 --- a/keyboards/handwired/arrow_pad/keymaps/pad_21/config.h +++ b/keyboards/handwired/arrow_pad/keymaps/pad_21/config.h @@ -50,7 +50,7 @@ along with this program. If not, see <http://www.gnu.org/licenses/>. #define DIODE_DIRECTION ROW2COL /* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */ -#define DEBOUNCING_DELAY 5 +#define DEBOUNCE 5 /* define if matrix has ghost (lacks anti-ghosting diodes) */ //#define MATRIX_HAS_GHOST diff --git a/keyboards/handwired/arrow_pad/keymaps/pad_24/config.h b/keyboards/handwired/arrow_pad/keymaps/pad_24/config.h index db89e4b84..aba085f3d 100644 --- a/keyboards/handwired/arrow_pad/keymaps/pad_24/config.h +++ b/keyboards/handwired/arrow_pad/keymaps/pad_24/config.h @@ -52,7 +52,7 @@ along with this program. If not, see <http://www.gnu.org/licenses/>. #define DIODE_DIRECTION ROW2COL /* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */ -#define DEBOUNCING_DELAY 5 +#define DEBOUNCE 5 /* define if matrix has ghost (lacks anti-ghosting diodes) */ //#define MATRIX_HAS_GHOST diff --git a/keyboards/handwired/atreus50/config.h b/keyboards/handwired/atreus50/config.h index 4cdc7ed12..0d51e1185 100644 --- a/keyboards/handwired/atreus50/config.h +++ b/keyboards/handwired/atreus50/config.h @@ -45,7 +45,7 @@ along with this program. If not, see <http://www.gnu.org/licenses/>. // #define BACKLIGHT_LEVELS 3 /* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */ -#define DEBOUNCING_DELAY 5 +#define DEBOUNCE 5 /* define if matrix has ghost (lacks anti-ghosting diodes) */ //#define MATRIX_HAS_GHOST diff --git a/keyboards/handwired/cmd60/config.h b/keyboards/handwired/cmd60/config.h index e95cac1e4..ee676ca05 100644 --- a/keyboards/handwired/cmd60/config.h +++ b/keyboards/handwired/cmd60/config.h @@ -54,7 +54,7 @@ along with this program. If not, see <http://www.gnu.org/licenses/>. // #define BACKLIGHT_LEVELS 3 /* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */ -#define DEBOUNCING_DELAY 5 +#define DEBOUNCE 5 /* define if matrix has ghost (lacks anti-ghosting diodes) */ //#define MATRIX_HAS_GHOST diff --git a/keyboards/handwired/co60/info.json b/keyboards/handwired/co60/info.json new file mode 100644 index 000000000..46f369f92 --- /dev/null +++ b/keyboards/handwired/co60/info.json @@ -0,0 +1,38 @@ +{ + "keyboard_name": "CO60", + "url": "https://github.com/jmdaly/CO60", + "maintainer": "qmk", + "width": 15, + "height": 5, + "layouts": { + "LAYOUT_all": { + "key_count": 68, + "layout": [{"label":"Esc", "x":0, "y":0}, {"label":"!", "x":1, "y":0}, {"label":"@", "x":2, "y":0}, {"label":"#", "x":3, "y":0}, {"label":"$", "x":4, "y":0}, {"label":"%", "x":5, "y":0}, {"label":"^", "x":6, "y":0}, {"label":"&", "x":7, "y":0}, {"label":"*", "x":8, "y":0}, {"label":"(", "x":9, "y":0}, {"label":")", "x":10, "y":0}, {"label":"_", "x":11, "y":0}, {"label":"+", "x":12, "y":0}, {"label":"~", "x":13, "y":0}, {"label":"Del", "x":14, "y":0}, {"label":"Tab", "x":0, "y":1, "w":1.5}, {"label":"Q", "x":1.5, "y":1}, {"label":"W", "x":2.5, "y":1}, {"label":"E", "x":3.5, "y":1}, {"label":"R", "x":4.5, "y":1}, {"label":"T", "x":5.5, "y":1}, {"label":"Y", "x":6.5, "y":1}, {"label":"U", "x":7.5, "y":1}, {"label":"I", "x":8.5, "y":1}, {"label":"O", "x":9.5, "y":1}, {"label":"P", "x":10.5, "y":1}, {"label":"{", "x":11.5, "y":1}, {"label":"}", "x":12.5, "y":1}, {"label":"|", "x":13.5, "y":1, "w":1.5}, {"label":"Caps Lock", "x":0, "y":2, "w":1.75}, {"label":"A", "x":1.75, "y":2}, {"label":"S", "x":2.75, "y":2}, {"label":"D", "x":3.75, "y":2}, {"label":"F", "x":4.75, "y":2}, {"label":"G", "x":5.75, "y":2}, {"label":"H", "x":6.75, "y":2}, {"label":"J", "x":7.75, "y":2}, {"label":"K", "x":8.75, "y":2}, {"label":"L", "x":9.75, "y":2}, {"label":":", "x":10.75, "y":2}, {"label":"\"", "x":11.75, "y":2}, {"x":12.75, "y":2}, {"label":"Enter", "x":13.75, "y":2, "w":1.25}, {"label":"Shift", "x":0, "y":3, "w":1.25}, {"x":1.25, "y":3}, {"label":"Z", "x":2.25, "y":3}, {"label":"X", "x":3.25, "y":3}, {"label":"C", "x":4.25, "y":3}, {"label":"V", "x":5.25, "y":3}, {"label":"B", "x":6.25, "y":3}, {"label":"N", "x":7.25, "y":3}, {"label":"M", "x":8.25, "y":3}, {"label":"<", "x":9.25, "y":3}, {"label":">", "x":10.25, "y":3}, {"label":"?", "x":11.25, "y":3}, {"label":"Shift", "x":12.25, "y":3, "w":1.75}, {"label":"Fn", "x":14, "y":3}, {"label":"Ctrl", "x":0, "y":4, "w":1.25}, {"label":"Win", "x":1.25, "y":4, "w":1.25}, {"label":"Alt", "x":2.5, "y":4, "w":1.25}, {"label":"LSpace", "x":3.75, "y":4, "w":2.25}, {"label":"Fn", "x":6, "y":4, "w":1.25}, {"label":"RSpace", "x":7.25, "y":4, "w":2.75}, {"label":"Alt", "x":10, "y":4, "w":1}, {"label":"Win", "x":11, "y":4, "w":1}, {"label":"Menu", "x":12, "y":4, "w":1}, {"label":"Ctrl", "x":13, "y":4, "w":1}, {"label":"Fn", "x":14, "y":4, "w":1}] + }, + "LAYOUT_60_ansi": { + "key_count": 61, + "layout": [{"label":"~", "x":0, "y":0}, {"label":"!", "x":1, "y":0}, {"label":"@", "x":2, "y":0}, {"label":"#", "x":3, "y":0}, {"label":"$", "x":4, "y":0}, {"label":"%", "x":5, "y":0}, {"label":"^", "x":6, "y":0}, {"label":"&", "x":7, "y":0}, {"label":"*", "x":8, "y":0}, {"label":"(", "x":9, "y":0}, {"label":")", "x":10, "y":0}, {"label":"_", "x":11, "y":0}, {"label":"+", "x":12, "y":0}, {"label":"Backspace", "x":13, "y":0, "w":2}, {"label":"Tab", "x":0, "y":1, "w":1.5}, {"label":"Q", "x":1.5, "y":1}, {"label":"W", "x":2.5, "y":1}, {"label":"E", "x":3.5, "y":1}, {"label":"R", "x":4.5, "y":1}, {"label":"T", "x":5.5, "y":1}, {"label":"Y", "x":6.5, "y":1}, {"label":"U", "x":7.5, "y":1}, {"label":"I", "x":8.5, "y":1}, {"label":"O", "x":9.5, "y":1}, {"label":"P", "x":10.5, "y":1}, {"label":"{", "x":11.5, "y":1}, {"label":"}", "x":12.5, "y":1}, {"label":"|", "x":13.5, "y":1, "w":1.5}, {"label":"CapsLock", "x":0, "y":2, "w":1.75}, {"label":"A", "x":1.75, "y":2}, {"label":"S", "x":2.75, "y":2}, {"label":"D", "x":3.75, "y":2}, {"label":"F", "x":4.75, "y":2}, {"label":"G", "x":5.75, "y":2}, {"label":"H", "x":6.75, "y":2}, {"label":"J", "x":7.75, "y":2}, {"label":"K", "x":8.75, "y":2}, {"label":"L", "x":9.75, "y":2}, {"label":":", "x":10.75, "y":2}, {"label":"\"", "x":11.75, "y":2}, {"label":"Enter", "x":12.75, "y":2, "w":2.25}, {"label":"Shift", "x":0, "y":3, "w":2.25}, {"label":"Z", "x":2.25, "y":3}, {"label":"X", "x":3.25, "y":3}, {"label":"C", "x":4.25, "y":3}, {"label":"V", "x":5.25, "y":3}, {"label":"B", "x":6.25, "y":3}, {"label":"N", "x":7.25, "y":3}, {"label":"M", "x":8.25, "y":3}, {"label":"<", "x":9.25, "y":3}, {"label":">", "x":10.25, "y":3}, {"label":"?", "x":11.25, "y":3}, {"label":"Shift", "x":12.25, "y":3, "w":2.75}, {"label":"Ctrl", "x":0, "y":4, "w":1.25}, {"label":"Win", "x":1.25, "y":4, "w":1.25}, {"label":"Alt", "x":2.5, "y":4, "w":1.25}, {"x":3.75, "y":4, "w":6.25}, {"label":"Alt", "x":10, "y":4, "w":1.25}, {"label":"Win", "x":11.25, "y":4, "w":1.25}, {"label":"Menu", "x":12.5, "y":4, "w":1.25}, {"label":"Ctrl", "x":13.75, "y":4, "w":1.25}] + }, + "LAYOUT_60_ansi_split_bs_rshift": { + "key_count": 63, + "layout": [{"label":"Esc", "x":0, "y":0}, {"label":"!", "x":1, "y":0}, {"label":"@", "x":2, "y":0}, {"label":"#", "x":3, "y":0}, {"label":"$", "x":4, "y":0}, {"label":"%", "x":5, "y":0}, {"label":"^", "x":6, "y":0}, {"label":"&", "x":7, "y":0}, {"label":"*", "x":8, "y":0}, {"label":"(", "x":9, "y":0}, {"label":")", "x":10, "y":0}, {"label":"_", "x":11, "y":0}, {"label":"+", "x":12, "y":0}, {"label":"~", "x":13, "y":0, "w":1}, {"label":"Del", "x":14, "y":0, "w":1}, {"label":"Tab", "x":0, "y":1, "w":1.5}, {"label":"Q", "x":1.5, "y":1}, {"label":"W", "x":2.5, "y":1}, {"label":"E", "x":3.5, "y":1}, {"label":"R", "x":4.5, "y":1}, {"label":"T", "x":5.5, "y":1}, {"label":"Y", "x":6.5, "y":1}, {"label":"U", "x":7.5, "y":1}, {"label":"I", "x":8.5, "y":1}, {"label":"O", "x":9.5, "y":1}, {"label":"P", "x":10.5, "y":1}, {"label":"{", "x":11.5, "y":1}, {"label":"}", "x":12.5, "y":1}, {"label":"|", "x":13.5, "y":1, "w":1.5}, {"label":"CapsLock", "x":0, "y":2, "w":1.75}, {"label":"A", "x":1.75, "y":2}, {"label":"S", "x":2.75, "y":2}, {"label":"D", "x":3.75, "y":2}, {"label":"F", "x":4.75, "y":2}, {"label":"G", "x":5.75, "y":2}, {"label":"H", "x":6.75, "y":2}, {"label":"J", "x":7.75, "y":2}, {"label":"K", "x":8.75, "y":2}, {"label":"L", "x":9.75, "y":2}, {"label":":", "x":10.75, "y":2}, {"label":"\"", "x":11.75, "y":2}, {"label":"Enter", "x":12.75, "y":2, "w":2.25}, {"label":"Shift", "x":0, "y":3, "w":2.25}, {"label":"Z", "x":2.25, "y":3}, {"label":"X", "x":3.25, "y":3}, {"label":"C", "x":4.25, "y":3}, {"label":"V", "x":5.25, "y":3}, {"label":"B", "x":6.25, "y":3}, {"label":"N", "x":7.25, "y":3}, {"label":"M", "x":8.25, "y":3}, {"label":"<", "x":9.25, "y":3}, {"label":">", "x":10.25, "y":3}, {"label":"?", "x":11.25, "y":3}, {"label":"Shift", "x":12.25, "y":3, "w":1.75}, {"label":"Fn", "x":14, "y":3, "w":1}, {"label":"Ctrl", "x":0, "y":4, "w":1.25}, {"label":"Win", "x":1.25, "y":4, "w":1.25}, {"label":"Alt", "x":2.5, "y":4, "w":1.25}, {"x":3.75, "y":4, "w":6.25}, {"label":"Alt", "x":10, "y":4, "w":1.25}, {"label":"Win", "x":11.25, "y":4, "w":1.25}, {"label":"Menu", "x":12.5, "y":4, "w":1.25}, {"label":"Ctrl", "x":13.75, "y":4, "w":1.25}] + }, + "LAYOUT_60_iso": { + "key_count": 62, + "layout": [{"label":"Esc", "x":0, "y":0}, {"label":"!", "x":1, "y":0}, {"label":"\"", "x":2, "y":0}, {"label":"£", "x":3, "y":0}, {"label":"$", "x":4, "y":0}, {"label":"%", "x":5, "y":0}, {"label":"^", "x":6, "y":0}, {"label":"&", "x":7, "y":0}, {"label":"*", "x":8, "y":0}, {"label":"(", "x":9, "y":0}, {"label":")", "x":10, "y":0}, {"label":"_", "x":11, "y":0}, {"label":"+", "x":12, "y":0}, {"label":"Backspace", "x":13, "y":0, "w":2}, {"label":"Tab", "x":0, "y":1, "w":1.5}, {"label":"Q", "x":1.5, "y":1}, {"label":"W", "x":2.5, "y":1}, {"label":"E", "x":3.5, "y":1}, {"label":"R", "x":4.5, "y":1}, {"label":"T", "x":5.5, "y":1}, {"label":"Y", "x":6.5, "y":1}, {"label":"U", "x":7.5, "y":1}, {"label":"I", "x":8.5, "y":1}, {"label":"O", "x":9.5, "y":1}, {"label":"P", "x":10.5, "y":1}, {"label":"[", "x":11.5, "y":1}, {"label":"]", "x":12.5, "y":1}, {"label":"CapsLock", "x":0, "y":2, "w":1.75}, {"label":"A", "x":1.75, "y":2}, {"label":"S", "x":2.75, "y":2}, {"label":"D", "x":3.75, "y":2}, {"label":"F", "x":4.75, "y":2}, {"label":"G", "x":5.75, "y":2}, {"label":"H", "x":6.75, "y":2}, {"label":"J", "x":7.75, "y":2}, {"label":"K", "x":8.75, "y":2}, {"label":"L", "x":9.75, "y":2}, {"label":":", "x":10.75, "y":2}, {"label":"@", "x":11.75, "y":2}, {"label":"~", "x":12.75, "y":2}, {"label":"Enter", "x":13.75, "y":1, "w":1.25, "h":2}, {"label":"Shift", "x":0, "y":3, "w":1.25}, {"label":"|", "x":1.25, "y":3}, {"label":"Z", "x":2.25, "y":3}, {"label":"X", "x":3.25, "y":3}, {"label":"C", "x":4.25, "y":3}, {"label":"V", "x":5.25, "y":3}, {"label":"B", "x":6.25, "y":3}, {"label":"N", "x":7.25, "y":3}, {"label":"M", "x":8.25, "y":3}, {"label":"<", "x":9.25, "y":3}, {"label":">", "x":10.25, "y":3}, {"label":"?", "x":11.25, "y":3}, {"label":"Shift", "x":12.25, "y":3, "w":2.75}, {"label":"Ctrl", "x":0, "y":4, "w":1.25}, {"label":"Win", "x":1.25, "y":4, "w":1.25}, {"label":"Alt", "x":2.5, "y":4, "w":1.25}, {"x":3.75, "y":4, "w":6.25}, {"label":"AltGr", "x":10, "y":4, "w":1.25}, {"label":"Win", "x":11.25, "y":4, "w":1.25}, {"label":"Menu", "x":12.5, "y":4, "w":1.25}, {"label":"Ctrl", "x":13.75, "y":4, "w":1.25}] + }, + "LAYOUT_60_hhkb": { + "key_count": 60, + "layout": [{"label":"Esc", "x":0, "y":0}, {"label":"!", "x":1, "y":0}, {"label":"@", "x":2, "y":0}, {"label":"#", "x":3, "y":0}, {"label":"$", "x":4, "y":0}, {"label":"%", "x":5, "y":0}, {"label":"^", "x":6, "y":0}, {"label":"&", "x":7, "y":0}, {"label":"*", "x":8, "y":0}, {"label":"(", "x":9, "y":0}, {"label":")", "x":10, "y":0}, {"label":"_", "x":11, "y":0}, {"label":"+", "x":12, "y":0}, {"label":"~", "x":13, "y":0}, {"label":"Del", "x":14, "y":0}, {"label":"Tab", "x":0, "y":1, "w":1.5}, {"label":"Q", "x":1.5, "y":1}, {"label":"W", "x":2.5, "y":1}, {"label":"E", "x":3.5, "y":1}, {"label":"R", "x":4.5, "y":1}, {"label":"T", "x":5.5, "y":1}, {"label":"Y", "x":6.5, "y":1}, {"label":"U", "x":7.5, "y":1}, {"label":"I", "x":8.5, "y":1}, {"label":"O", "x":9.5, "y":1}, {"label":"P", "x":10.5, "y":1}, {"label":"[", "x":11.5, "y":1}, {"label":"]", "x":12.5, "y":1}, {"label":"Backspace", "x":13.5, "y":1, "w":1.5}, {"label":"CapsLock", "x":0, "y":2, "w":1.75}, {"label":"A", "x":1.75, "y":2}, {"label":"S", "x":2.75, "y":2}, {"label":"D", "x":3.75, "y":2}, {"label":"F", "x":4.75, "y":2}, {"label":"G", "x":5.75, "y":2}, {"label":"H", "x":6.75, "y":2}, {"label":"J", "x":7.75, "y":2}, {"label":"K", "x":8.75, "y":2}, {"label":"L", "x":9.75, "y":2}, {"label":":", "x":10.75, "y":2}, {"label":"\"", "x":11.75, "y":2}, {"label":"Enter", "x":12.75, "y":2, "w":2.25}, {"label":"Shift", "x":0, "y":3, "w":2.25}, {"label":"Z", "x":2.25, "y":3}, {"label":"X", "x":3.25, "y":3}, {"label":"C", "x":4.25, "y":3}, {"label":"V", "x":5.25, "y":3}, {"label":"B", "x":6.25, "y":3}, {"label":"N", "x":7.25, "y":3}, {"label":"M", "x":8.25, "y":3}, {"label":"<", "x":9.25, "y":3}, {"label":">", "x":10.25, "y":3}, {"label":"?", "x":11.25, "y":3}, {"label":"Shift", "x":12.25, "y":3, "w":1.75},{"label":"Fn", "x":14, "y":3}, {"label":"Win", "x":1.5, "y":4}, {"label":"Alt", "x":2.5, "y":4, "w":1.5}, {"label":"Space", "x":4, "y":4, "w":7}, {"label":"Alt", "x":11, "y":4, "w":1.5}, {"label":"Win", "x":12.5, "y":4}] + }, + "LAYOUT_60_hhkb_split_space": { + "key_count": 62, + "layout": [{"label":"Esc", "x":0, "y":0}, {"label":"!", "x":1, "y":0}, {"label":"@", "x":2, "y":0}, {"label":"#", "x":3, "y":0}, {"label":"$", "x":4, "y":0}, {"label":"%", "x":5, "y":0}, {"label":"^", "x":6, "y":0}, {"label":"&", "x":7, "y":0}, {"label":"*", "x":8, "y":0}, {"label":"(", "x":9, "y":0}, {"label":")", "x":10, "y":0}, {"label":"_", "x":11, "y":0}, {"label":"+", "x":12, "y":0}, {"label":"~", "x":13, "y":0}, {"label":"Del", "x":14, "y":0}, {"label":"Tab", "x":0, "y":1, "w":1.5}, {"label":"Q", "x":1.5, "y":1}, {"label":"W", "x":2.5, "y":1}, {"label":"E", "x":3.5, "y":1}, {"label":"R", "x":4.5, "y":1}, {"label":"T", "x":5.5, "y":1}, {"label":"Y", "x":6.5, "y":1}, {"label":"U", "x":7.5, "y":1}, {"label":"I", "x":8.5, "y":1}, {"label":"O", "x":9.5, "y":1}, {"label":"P", "x":10.5, "y":1}, {"label":"[", "x":11.5, "y":1}, {"label":"]", "x":12.5, "y":1}, {"label":"Backspace", "x":13.5, "y":1, "w":1.5}, {"label":"CapsLock", "x":0, "y":2, "w":1.75}, {"label":"A", "x":1.75, "y":2}, {"label":"S", "x":2.75, "y":2}, {"label":"D", "x":3.75, "y":2}, {"label":"F", "x":4.75, "y":2}, {"label":"G", "x":5.75, "y":2}, {"label":"H", "x":6.75, "y":2}, {"label":"J", "x":7.75, "y":2}, {"label":"K", "x":8.75, "y":2}, {"label":"L", "x":9.75, "y":2}, {"label":":", "x":10.75, "y":2}, {"label":"\"", "x":11.75, "y":2}, {"label":"Enter", "x":12.75, "y":2, "w":2.25}, {"label":"Shift", "x":0, "y":3, "w":2.25}, {"label":"Z", "x":2.25, "y":3}, {"label":"X", "x":3.25, "y":3}, {"label":"C", "x":4.25, "y":3}, {"label":"V", "x":5.25, "y":3}, {"label":"B", "x":6.25, "y":3}, {"label":"N", "x":7.25, "y":3}, {"label":"M", "x":8.25, "y":3}, {"label":"<", "x":9.25, "y":3}, {"label":">", "x":10.25, "y":3}, {"label":"?", "x":11.25, "y":3}, {"label":"Shift", "x":12.25, "y":3, "w":1.75},{"label":"Fn", "x":14, "y":3}, {"label":"Win", "x":1.5, "y":4}, {"label":"Alt", "x":2.5, "y":4, "w":1.5}, {"label":"LSpace", "x":4, "y":4, "w":2.75}, {"label":"Fn", "x":6.75, "y":4, "w":1.5}, {"label":"RSpace", "x":8.25, "y":4, "w":2.75}, {"label":"Alt", "x":11, "y":4, "w":1.5}, {"label":"Win", "x":12.5, "y":4}] + }, + "LAYOUT_60_hhkb_split_625u_space": { + "key_count": 63, + "layout": [{"label":"Esc", "x":0, "y":0}, {"label":"!", "x":1, "y":0}, {"label":"@", "x":2, "y":0}, {"label":"#", "x":3, "y":0}, {"label":"$", "x":4, "y":0}, {"label":"%", "x":5, "y":0}, {"label":"^", "x":6, "y":0}, {"label":"&", "x":7, "y":0}, {"label":"*", "x":8, "y":0}, {"label":"(", "x":9, "y":0}, {"label":")", "x":10, "y":0}, {"label":"_", "x":11, "y":0}, {"label":"+", "x":12, "y":0}, {"label":"~", "x":13, "y":0}, {"label":"Del", "x":14, "y":0}, {"label":"Tab", "x":0, "y":1, "w":1.5}, {"label":"Q", "x":1.5, "y":1}, {"label":"W", "x":2.5, "y":1}, {"label":"E", "x":3.5, "y":1}, {"label":"R", "x":4.5, "y":1}, {"label":"T", "x":5.5, "y":1}, {"label":"Y", "x":6.5, "y":1}, {"label":"U", "x":7.5, "y":1}, {"label":"I", "x":8.5, "y":1}, {"label":"O", "x":9.5, "y":1}, {"label":"P", "x":10.5, "y":1}, {"label":"[", "x":11.5, "y":1}, {"label":"]", "x":12.5, "y":1}, {"label":"Backspace", "x":13.5, "y":1, "w":1.5}, {"label":"CapsLock", "x":0, "y":2, "w":1.75}, {"label":"A", "x":1.75, "y":2}, {"label":"S", "x":2.75, "y":2}, {"label":"D", "x":3.75, "y":2}, {"label":"F", "x":4.75, "y":2}, {"label":"G", "x":5.75, "y":2}, {"label":"H", "x":6.75, "y":2}, {"label":"J", "x":7.75, "y":2}, {"label":"K", "x":8.75, "y":2}, {"label":"L", "x":9.75, "y":2}, {"label":":", "x":10.75, "y":2}, {"label":"\"", "x":11.75, "y":2}, {"label":"Enter", "x":12.75, "y":2, "w":2.25}, {"label":"Shift", "x":0, "y":3, "w":2.25}, {"label":"Z", "x":2.25, "y":3}, {"label":"X", "x":3.25, "y":3}, {"label":"C", "x":4.25, "y":3}, {"label":"V", "x":5.25, "y":3}, {"label":"B", "x":6.25, "y":3}, {"label":"N", "x":7.25, "y":3}, {"label":"M", "x":8.25, "y":3}, {"label":"<", "x":9.25, "y":3}, {"label":">", "x":10.25, "y":3}, {"label":"?", "x":11.25, "y":3}, {"label":"Shift", "x":12.25, "y":3, "w":1.75},{"label":"Fn", "x":14, "y":3}, {"label":"Win", "x":1.5, "y":4}, {"label":"Alt", "x":2.5, "y":4, "w":1.25}, {"label":"LSpace", "x":3.75, "y":4, "w":2.25}, {"label":"Fn", "x":6, "y":4, "w":1.25}, {"label":"RSpace", "x":7.25, "y":4, "w":2.75}, {"label":"Menu", "x":10, "y":4, "w":1.25}, {"label":"Alt", "x":11.25, "y":4, "w":1.25}, {"label":"Win", "x":12.5, "y":4}] + } + } +} + diff --git a/keyboards/handwired/co60/keymaps/all_keys/config.h b/keyboards/handwired/co60/keymaps/all_keys/config.h new file mode 100644 index 000000000..a68c5c746 --- /dev/null +++ b/keyboards/handwired/co60/keymaps/all_keys/config.h @@ -0,0 +1,20 @@ +/* Copyright 2019 John M Daly <jmdaly@gmail.com> + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#pragma once + + +// place overrides here diff --git a/keyboards/handwired/co60/keymaps/all_keys/keymap.c b/keyboards/handwired/co60/keymaps/all_keys/keymap.c new file mode 100644 index 000000000..797b7ece3 --- /dev/null +++ b/keyboards/handwired/co60/keymaps/all_keys/keymap.c @@ -0,0 +1,48 @@ +/* Copyright 2019 John M Daly <jmdaly@gmail.com> + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ +#include QMK_KEYBOARD_H + + +enum co60_layers { + _L1, + _L2 +}; + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { + [_L1] = LAYOUT_all( /* Base */ + KC_ESC, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_EQL, KC_GRV, KC_DEL, + KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_LBRC, KC_RBRC, KC_BSLS, + KC_CAPS, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT, KC_NUHS, KC_ENT, + KC_LSFT, KC_NUBS, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, KC_RSFT, KC_LSFT, + KC_LCTL, KC_LGUI, KC_LALT, KC_ENT, KC_HOME, KC_END, KC_INS, KC_RALT, KC_RGUI, KC_RIGHT, KC_RCTL + ) +}; + +void matrix_init_user(void) { + +} + +void matrix_scan_user(void) { + +} + +bool process_record_user(uint16_t keycode, keyrecord_t *record) { + return true; +} + +void led_set_user(uint8_t usb_led) { + +} diff --git a/keyboards/handwired/co60/keymaps/all_keys/readme.md b/keyboards/handwired/co60/keymaps/all_keys/readme.md new file mode 100644 index 000000000..0e472f235 --- /dev/null +++ b/keyboards/handwired/co60/keymaps/all_keys/readme.md @@ -0,0 +1,5 @@ +# Keymap that uses all possible switches + +This is in part to test all of the switches, +but also it may be useful if anyone ever makes a +layout that requires all switch positions. diff --git a/keyboards/handwired/co60/keymaps/default/config.h b/keyboards/handwired/co60/keymaps/default/config.h new file mode 100644 index 000000000..124091cc5 --- /dev/null +++ b/keyboards/handwired/co60/keymaps/default/config.h @@ -0,0 +1,19 @@ +/* Copyright 2018 John M Daly + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#pragma once + +// place overrides here diff --git a/keyboards/handwired/co60/keymaps/default/keymap.c b/keyboards/handwired/co60/keymaps/default/keymap.c new file mode 100644 index 000000000..35151c421 --- /dev/null +++ b/keyboards/handwired/co60/keymaps/default/keymap.c @@ -0,0 +1,54 @@ +/* Copyright 2019 John M Daly <jmdaly@gmail.com> + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ +#include QMK_KEYBOARD_H + +enum co60_layers { + _L1, + _L2 +}; + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { + [_L1] = LAYOUT_60_ansi( /* Base */ + KC_ESC, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_EQL, KC_BSPC, + KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_LBRC, KC_RBRC, KC_BSLS, + KC_CAPS, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT, KC_ENT, + KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, KC_RSFT, + KC_LCTL, KC_LGUI, KC_LALT, KC_SPC, KC_RALT, KC_RGUI, MO(_L2), KC_RCTL + ), + [_L2] = LAYOUT_60_ansi( /* Base */ + RESET, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, KC_GRV, + _______, BL_TOGG, BL_INC, _______, _______, _______, _______, _______, _______, _______, _______, KC_PGUP, _______, KC_INSERT, + _______, _______, _______, _______, _______, _______, KC_LEFT, KC_DOWN, KC_UP, KC_RIGHT, KC_HOME, KC_END, _______, + _______, BL_DEC, _______, _______, _______, _______, _______, _______, _______, _______, KC_PGDOWN, _______, + _______, _______, _______, _______, _______, _______, _______, _______ + ) +}; + +void matrix_init_user(void) { + +} + +void matrix_scan_user(void) { + +} + +bool process_record_user(uint16_t keycode, keyrecord_t *record) { + return true; +} + +void led_set_user(uint8_t usb_led) { + +} diff --git a/keyboards/handwired/co60/keymaps/default/readme.md b/keyboards/handwired/co60/keymaps/default/readme.md new file mode 100644 index 000000000..eb8ba49e3 --- /dev/null +++ b/keyboards/handwired/co60/keymaps/default/readme.md @@ -0,0 +1 @@ +# The default keymap for co60
\ No newline at end of file diff --git a/keyboards/handwired/co60/keymaps/jmdaly_hhkb_split_space/config.h b/keyboards/handwired/co60/keymaps/jmdaly_hhkb_split_space/config.h new file mode 100644 index 000000000..c88fbc29d --- /dev/null +++ b/keyboards/handwired/co60/keymaps/jmdaly_hhkb_split_space/config.h @@ -0,0 +1,21 @@ +/* Copyright 2019 John M Daly <jmdaly@gmail.com> + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#pragma once + +#define LEADER_TIMEOUT 300 + +// place overrides here diff --git a/keyboards/handwired/co60/keymaps/jmdaly_hhkb_split_space/keymap.c b/keyboards/handwired/co60/keymaps/jmdaly_hhkb_split_space/keymap.c new file mode 100644 index 000000000..0f19f9fbe --- /dev/null +++ b/keyboards/handwired/co60/keymaps/jmdaly_hhkb_split_space/keymap.c @@ -0,0 +1,137 @@ +/* Copyright 2019 John M Daly <jmdaly@gmail.com> + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ +#include QMK_KEYBOARD_H + +enum co60_layers { + _L1, + _L2, + _L3 +}; + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { + // Default base layer. Except for the bottom row, this + // is close to a standard HHKB layout. + [_L1] = LAYOUT_60_hhkb_split_625u_space( /* Base */ + KC_ESC, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_EQL, KC_BSLS, KC_GRV, + KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_LBRC, KC_RBRC, KC_BSPC, + CTL_T(KC_ESC), KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT, KC_ENT, + KC_LSPO, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, KC_RSPC, MO(_L3), + KC_LALT, KC_LGUI, KC_ENT, MO(_L3), KC_SPC, KC_LEAD, KC_RGUI, KC_RALT + ), + // My preferred base layout. This doesn't match the caps + // on my boards, so I don't make it default. + [_L2] = LAYOUT_60_hhkb_split_625u_space( /* Base */ + KC_GRV, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_EQL, KC_BSLS, KC_DEL, + KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_LBRC, KC_RBRC, KC_BSPC, + CTL_T(KC_ESC), KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT, KC_ENT, + KC_LSPO, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, KC_RSPC, MO(_L3), + KC_LALT, KC_LGUI, KC_ENT, MO(_L3), KC_SPC, KC_LEAD, KC_RGUI, KC_RALT + ), + [_L3] = LAYOUT_60_hhkb_split_625u_space( /* Function */ + RESET, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, _______, _______, + BL_BRTG, BL_TOGG, BL_INC, BL_DEC, BL_ON, BL_OFF, _______, _______, _______, _______, _______, KC_PGUP, KC_INSERT, KC_DEL, + _______, RGB_TOG, RGB_MOD, RGB_RMOD, _______, _______, KC_LEFT, KC_DOWN, KC_UP, KC_RIGHT, KC_HOME, KC_END, _______, + _______, BL_DEC, _______, _______, _______, _______, _______, DF(_L1), DF(_L2), _______, KC_PGDOWN, _______, _______, + _______, _______, _______, _______, _______, _______, _______, _______ + ) +}; + +void matrix_init_user(void) { + +} + +LEADER_EXTERNS(); + +void matrix_scan_user(void) { + + LEADER_DICTIONARY() { + leading = false; + leader_end(); + + // Close a program in i3wm + SEQ_ONE_KEY(KC_Q) { + register_code(KC_LGUI); + register_code(KC_LSHIFT); + register_code(KC_Q); + unregister_code(KC_Q); + unregister_code(KC_LSHIFT); + unregister_code(KC_LGUI); + } + // Exit i3wm + SEQ_ONE_KEY(KC_E) { + register_code(KC_LGUI); + register_code(KC_LSHIFT); + register_code(KC_E); + unregister_code(KC_E); + unregister_code(KC_LSHIFT); + unregister_code(KC_LGUI); + } + // Copy selected text in suckless terminal + SEQ_ONE_KEY(KC_C) { + register_code(KC_LCTL); + register_code(KC_LSHIFT); + register_code(KC_C); + unregister_code(KC_C); + unregister_code(KC_LSHIFT); + unregister_code(KC_LCTL); + } + // Paste text in suckless terminal + SEQ_ONE_KEY(KC_V) { + register_code(KC_LCTL); + register_code(KC_LSHIFT); + register_code(KC_V); + unregister_code(KC_V); + unregister_code(KC_LSHIFT); + unregister_code(KC_LCTL); + } + // FZF shortcut to fuzzy switch directories + SEQ_ONE_KEY(KC_D) { + register_code(KC_LALT); + register_code(KC_C); + unregister_code(KC_C); + unregister_code(KC_LALT); + } + // Send keys to bring up fuzzy process kill + SEQ_ONE_KEY(KC_K) { + SEND_STRING("kill " SS_TAP(X_TAB)); + } + // Send keys to start neovim and fuzzy search for filename + SEQ_ONE_KEY(KC_T) { + SEND_STRING("nvim "); + register_code(KC_LCTL); + register_code(KC_T); + unregister_code(KC_T); + unregister_code(KC_LCTL); + } + // Switch between windows in tmux + SEQ_ONE_KEY(KC_L) { + register_code(KC_LCTL); + register_code(KC_B); + unregister_code(KC_B); + unregister_code(KC_LCTL); + register_code(KC_L); + unregister_code(KC_L); + } + } +} + +bool process_record_user(uint16_t keycode, keyrecord_t *record) { + return true; +} + +void led_set_user(uint8_t usb_led) { + +} diff --git a/keyboards/handwired/co60/keymaps/jmdaly_hhkb_split_space/readme.md b/keyboards/handwired/co60/keymaps/jmdaly_hhkb_split_space/readme.md new file mode 100644 index 000000000..032fc85f9 --- /dev/null +++ b/keyboards/handwired/co60/keymaps/jmdaly_hhkb_split_space/readme.md @@ -0,0 +1,6 @@ +# The split-space HHKB keymap for co60 + +This keymap implements a modified MX HHKB layout, but in addition to 7u space, +this layout supports a number of split spacebar bottom rows. The full set of +layout options is found +[here](http://www.keyboard-layout-editor.com/#/gists/b488496b3a71c8192113c07e298be340). diff --git a/keyboards/handwired/co60/readme.md b/keyboards/handwired/co60/readme.md new file mode 100644 index 000000000..2a649ea9b --- /dev/null +++ b/keyboards/handwired/co60/readme.md @@ -0,0 +1,26 @@ +# co60 + +The CO60 is a 60% PCB that aims to meet the following goals: + +* Switches oriented such that the LEDs are South-facing, for + compatibility with Cherry profile keycaps. +* USB Type-C support in both A to C and C to C configurations. +* QMK support. +* A variety of split spacebar configurations, including split 6.25U + space and split 7U space. +* ESD protection circuitry, including data line protection and a + polyfuse on the VCC line. +* Support for per-switch LED backlighting. +* Fits in standard 60% keyboard cases. + +More info on the project, including all of the design files, can be found [here](https://github.com/jmdaly/CO60). + +Keyboard Maintainer: [jmdaly](https://github.com/jmdaly) +Hardware Supported: Supports the CO60 PCB rev1, rev6, rev7 +Hardware Availability: Through group buys. + +Make example for this keyboard (after setting up your build environment): + + make handwired/co60/rev7:default + +See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs). diff --git a/keyboards/handwired/co60/rev1/config.h b/keyboards/handwired/co60/rev1/config.h new file mode 100644 index 000000000..4d5140daf --- /dev/null +++ b/keyboards/handwired/co60/rev1/config.h @@ -0,0 +1,161 @@ +/* +Copyright 2018 John M Daly <jmdaly@gmail.com> + +This program is free software: you can redistribute it and/or modify +it under the terms of the GNU General Public License as published by +the Free Software Foundation, either version 2 of the License, or +(at your option) any later version. + +This program is distributed in the hope that it will be useful, +but WITHOUT ANY WARRANTY; without even the implied warranty of +MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +GNU General Public License for more details. + +You should have received a copy of the GNU General Public License +along with this program. If not, see <http://www.gnu.org/licenses/>. +*/ + +#pragma once + +#include "config_common.h" + +/* USB Device descriptor parameter */ +#define VENDOR_ID 0xFEED +#define PRODUCT_ID 0x0000 +#define DEVICE_VER 0x0001 +#define MANUFACTURER John M Daly +#define PRODUCT CO60 +#define DESCRIPTION An open hardware sixty percent PCB + +/* key matrix size */ +#define MATRIX_ROWS 5 +#define MATRIX_COLS 15 + +/* + * Keyboard Matrix Assignments + * + * Change this to how you wired your keyboard + * COLS: AVR pins used for columns, left to right + * ROWS: AVR pins used for rows, top to bottom + * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode) + * ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode) + * +*/ +#define MATRIX_ROW_PINS { D0, D1, D2, D3, D5 } +#define MATRIX_COL_PINS { F0, F1, E6, C7, C6, B6, D4, B1, B2, B5, B4, D7, D6, B3, B0 } +#define UNUSED_PINS + +/* COL2ROW, ROW2COL, or CUSTOM_MATRIX */ +#define DIODE_DIRECTION COL2ROW + +#ifdef __AVR__ +#define BACKLIGHT_PIN B7 +#define BACKLIGHT_BREATHING +#endif +#define BACKLIGHT_LEVELS 3 + + +/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */ +#define DEBOUNCE 5 + +/* define if matrix has ghost (lacks anti-ghosting diodes) */ +//#define MATRIX_HAS_GHOST + +/* number of backlight levels */ + +/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ +// #define LOCKING_SUPPORT_ENABLE +/* Locking resynchronize hack */ +#define LOCKING_RESYNC_ENABLE + +/* If defined, GRAVE_ESC will always act as ESC when CTRL is held. + * This is userful for the Windows task manager shortcut (ctrl+shift+esc). + */ +// #define GRAVE_ESC_CTRL_OVERRIDE + +/* + * Force NKRO + * + * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved + * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the + * makefile for this to work.) + * + * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N) + * until the next keyboard reset. + * + * NKRO may prevent your keystrokes from being detected in the BIOS, but it is + * fully operational during normal computer usage. + * + * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N) + * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by + * bootmagic, NKRO mode will always be enabled until it is toggled again during a + * power-up. + * + */ +//#define FORCE_NKRO + +/* + * Magic Key Options + * + * Magic keys are hotkey commands that allow control over firmware functions of + * the keyboard. They are best used in combination with the HID Listen program, + * found here: https://www.pjrc.com/teensy/hid_listen.html + * + * The options below allow the magic key functionality to be changed. This is + * useful if your keyboard/keypad is missing keys and you want magic key support. + * + */ + +/* control how magic key switches layers */ +//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS true +//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS true +//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM false + +/* override magic key keymap */ +//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS +//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS +//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM +//#define MAGIC_KEY_HELP1 H +//#define MAGIC_KEY_HELP2 SLASH +//#define MAGIC_KEY_DEBUG D +//#define MAGIC_KEY_DEBUG_MATRIX X +//#define MAGIC_KEY_DEBUG_KBD K +//#define MAGIC_KEY_DEBUG_MOUSE M +//#define MAGIC_KEY_VERSION V +//#define MAGIC_KEY_STATUS S +//#define MAGIC_KEY_CONSOLE C +//#define MAGIC_KEY_LAYER0_ALT1 ESC +//#define MAGIC_KEY_LAYER0_ALT2 GRAVE +//#define MAGIC_KEY_LAYER0 0 +//#define MAGIC_KEY_LAYER1 1 +//#define MAGIC_KEY_LAYER2 2 +//#define MAGIC_KEY_LAYER3 3 +//#define MAGIC_KEY_LAYER4 4 +//#define MAGIC_KEY_LAYER5 5 +//#define MAGIC_KEY_LAYER6 6 +//#define MAGIC_KEY_LAYER7 7 +//#define MAGIC_KEY_LAYER8 8 +//#define MAGIC_KEY_LAYER9 9 +//#define MAGIC_KEY_BOOTLOADER PAUSE +//#define MAGIC_KEY_LOCK CAPS +//#define MAGIC_KEY_EEPROM E +//#define MAGIC_KEY_NKRO N +//#define MAGIC_KEY_SLEEP_LED Z + +/* + * Feature disable options + * These options are also useful to firmware size reduction. + */ + +/* disable debug print */ +//#define NO_DEBUG + +/* disable print */ +//#define NO_PRINT + +/* disable action features */ +//#define NO_ACTION_LAYER +//#define NO_ACTION_TAPPING +//#define NO_ACTION_ONESHOT +//#define NO_ACTION_MACRO +//#define NO_ACTION_FUNCTION diff --git a/keyboards/handwired/co60/rev1/rev1.c b/keyboards/handwired/co60/rev1/rev1.c new file mode 100644 index 000000000..abdfa884d --- /dev/null +++ b/keyboards/handwired/co60/rev1/rev1.c @@ -0,0 +1,46 @@ +/* Copyright 2018 John M Daly + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ +#include "rev1.h" + +__attribute__ ((weak)) +void matrix_init_kb(void) { + // put your keyboard start-up code here + // runs once when the firmware starts up + + matrix_init_user(); +} + +__attribute__ ((weak)) +void matrix_scan_kb(void) { + // put your looping keyboard code here + // runs every cycle (a lot) + + matrix_scan_user(); +} + +bool process_record_kb(uint16_t keycode, keyrecord_t *record) { + // put your per-action keyboard code here + // runs for every action, just before processing by the firmware + + return process_record_user(keycode, record); +} + +__attribute__ ((weak)) +void led_set_kb(uint8_t usb_led) { + // put your keyboard LED indicator (ex: Caps Lock LED) toggling code here + + led_set_user(usb_led); +} diff --git a/keyboards/handwired/co60/rev1/rev1.h b/keyboards/handwired/co60/rev1/rev1.h new file mode 100644 index 000000000..3cf6a853f --- /dev/null +++ b/keyboards/handwired/co60/rev1/rev1.h @@ -0,0 +1,127 @@ +/* Copyright 2018 John M Daly + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ +#pragma once + +#include "quantum.h" + +// This a shortcut to help you visually see your layout. +// The following is a layout that uses all available switch positions. +// The first section contains all of the arguments +// The second converts the arguments into a two-dimensional array +#define LAYOUT_all( \ + K000, K001, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011, K012, K013, K014, \ + K100, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111, K112, K113, K114, \ + K200, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211, K212, K213, K214, \ + K300, K301, K302, K303, K304, K305, K306, K307, K308, K309, K310, K311, K313, K314, \ + K400, K401, K402, K404, K406, K408, K410, K411, K412, K413, K414 \ +) \ +{ \ + { K000, K001, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011, K012, K013, K014 }, \ + { K100, KC_NO, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111, K112, K113, K114 }, \ + { K200, KC_NO, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211, K212, K213, K214 }, \ + { K300, K301, K302, K303, K304, K305, K306, K307, K308, K309, K310, K311, KC_NO, K313, K314 }, \ + { K400, K401, K402, KC_NO, K404, KC_NO, K406, KC_NO, K408, KC_NO, K410, K411, K412, K413, K414 }, \ +} + +#define LAYOUT_60_ansi( \ + K000, K001, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011, K012, K014, \ + K100, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111, K112, K113, K114, \ + K200, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211, K212, K214, \ + K300, K302, K303, K304, K305, K306, K307, K308, K309, K310, K311, K313, \ + K400, K401, K402, K406, K410, K411, K413, K414 \ +) \ +{ \ + { K000, K001, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011, K012, KC_NO, K014 }, \ + { K100, KC_NO, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111, K112, K113, K114 }, \ + { K200, KC_NO, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211, K212, KC_NO, K214 }, \ + { K300, KC_NO, K302, K303, K304, K305, K306, K307, K308, K309, K310, K311, KC_NO, K313, KC_NO }, \ + { K400, K401, K402, KC_NO, KC_NO, KC_NO, K406, KC_NO, KC_NO, KC_NO, K410, K411, KC_NO, K413, K414 }, \ +} + +#define LAYOUT_60_ansi_split_bs_rshift( \ + K000, K001, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011, K012, K013, K014, \ + K100, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111, K112, K113, K114, \ + K200, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211, K212, K214, \ + K300, K302, K303, K304, K305, K306, K307, K308, K309, K310, K311, K313, K314, \ + K400, K401, K402, K406, K410, K411, K413, K414 \ +) \ +{ \ + { K000, K001, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011, K012, K013, K014 }, \ + { K100, KC_NO, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111, K112, K113, K114 }, \ + { K200, KC_NO, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211, K212, KC_NO, K214 }, \ + { K300, KC_NO, K302, K303, K304, K305, K306, K307, K308, K309, K310, K311, KC_NO, K313, K314 }, \ + { K400, K401, K402, KC_NO, KC_NO, KC_NO, K406, KC_NO, KC_NO, KC_NO, K410, K411, KC_NO, K413, K414 }, \ +} + +#define LAYOUT_60_iso( \ + K000, K001, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011, K012, K014, \ + K100, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111, K112, K113, \ + K200, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211, K212, K213, K214, \ + K300, K301, K302, K303, K304, K305, K306, K307, K308, K309, K310, K311, K313, \ + K400, K401, K402, K406, K410, K411, K413, K414 \ +) \ +{ \ + { K000, K001, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011, K012, KC_NO, K014 }, \ + { K100, KC_NO, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111, K112, K113, KC_NO }, \ + { K200, KC_NO, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211, K212, K213, K214 }, \ + { K300, K301, K302, K303, K304, K305, K306, K307, K308, K309, K310, K311, KC_NO, K313, KC_NO }, \ + { K400, K401, K402, KC_NO, KC_NO, KC_NO, K406, KC_NO, KC_NO, KC_NO, K410, K411, KC_NO, K413, K414 }, \ +} + +#define LAYOUT_60_hhkb( \ + K000, K001, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011, K012, K013, K014, \ + K100, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111, K112, K113, K114, \ + K200, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211, K212, K214, \ + K300, K302, K303, K304, K305, K306, K307, K308, K309, K310, K311, K313, K314, \ + K401, K402, K406, K411, K413 \ +) \ +{ \ + { K000, K001, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011, K012, K013, K014 }, \ + { K100, KC_NO, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111, K112, K113, K114 }, \ + { K200, KC_NO, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211, K212, KC_NO, K214 }, \ + { K300, KC_NO, K302, K303, K304, K305, K306, K307, K308, K309, K310, K311, KC_NO, K313, K314 }, \ + { KC_NO, K401, K402, KC_NO, KC_NO, KC_NO, K406, KC_NO, KC_NO, KC_NO, KC_NO, K411, KC_NO, K413, KC_NO }, \ +} + +#define LAYOUT_60_hhkb_split_space( \ + K000, K001, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011, K012, K013, K014, \ + K100, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111, K112, K113, K114, \ + K200, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211, K212, K214, \ + K300, K302, K303, K304, K305, K306, K307, K308, K309, K310, K311, K313, K314, \ + K401, K402, K404, K406, K408, K411, K413 \ +) \ +{ \ + { K000, K001, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011, K012, K013, K014 }, \ + { K100, KC_NO, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111, K112, K113, K114 }, \ + { K200, KC_NO, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211, K212, KC_NO, K214 }, \ + { K300, KC_NO, K302, K303, K304, K305, K306, K307, K308, K309, K310, K311, KC_NO, K313, K314 }, \ + { KC_NO, K401, K402, KC_NO, K404, KC_NO, K406, KC_NO, K408, KC_NO, KC_NO, K411, KC_NO, K413, KC_NO }, \ +} + +#define LAYOUT_60_hhkb_split_625u_space( \ + K000, K001, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011, K012, K013, K014, \ + K100, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111, K112, K113, K114, \ + K200, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211, K212, K214, \ + K300, K302, K303, K304, K305, K306, K307, K308, K309, K310, K311, K313, K314, \ + K401, K402, K404, K406, K408, K410, K411, K413 \ +) \ +{ \ + { K000, K001, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011, K012, K013, K014 }, \ + { K100, KC_NO, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111, K112, K113, K114 }, \ + { K200, KC_NO, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211, K212, KC_NO, K214 }, \ + { K300, KC_NO, K302, K303, K304, K305, K306, K307, K308, K309, K310, K311, KC_NO, K313, K314 }, \ + { KC_NO, K401, K402, KC_NO, K404, KC_NO, K406, KC_NO, K408, KC_NO, K410, K411, KC_NO, K413, KC_NO }, \ +} diff --git a/keyboards/handwired/co60/rev1/rules.mk b/keyboards/handwired/co60/rev1/rules.mk new file mode 100644 index 000000000..31ce6cbe4 --- /dev/null +++ b/keyboards/handwired/co60/rev1/rules.mk @@ -0,0 +1,70 @@ +# MCU name +MCU = atmega32u4 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# atmega32a bootloadHID +BOOTLOADER = atmel-dfu + +# Build Options +# change yes to no to disable +# +BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE = yes # Mouse keys(+4700) +EXTRAKEY_ENABLE = yes # Audio control and System control(+450) +CONSOLE_ENABLE = no # Console for debug(+400) +COMMAND_ENABLE = no # Commands for debug and configuration +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend +# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +NKRO_ENABLE = yes # USB Nkey Rollover +BACKLIGHT_ENABLE = yes # Enable keyboard backlight functionality on B7 by default +MIDI_ENABLE = no # MIDI support (+2400 to 4200, depending on config) +UNICODE_ENABLE = no # Unicode +BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID +AUDIO_ENABLE = no # Audio output on port C6 +FAUXCLICKY_ENABLE = no # Use buzzer to emulate clicky switches +LEADER_ENABLE = yes # Turn on leader support + +# Layouts supported by this PCB: +LAYOUTS = 60_ansi 60_iso 60_ansi_split_bs_rshift 60_hhkb diff --git a/keyboards/handwired/co60/rev6/chconf.h b/keyboards/handwired/co60/rev6/chconf.h new file mode 100644 index 000000000..1d9f12ff1 --- /dev/null +++ b/keyboards/handwired/co60/rev6/chconf.h @@ -0,0 +1,520 @@ +/* + ChibiOS - Copyright (C) 2006..2016 Giovanni Di Sirio + + Licensed under the Apache License, Version 2.0 (the "License"); + you may not use this file except in compliance with the License. + You may obtain a copy of the License at + + http://www.apache.org/licenses/LICENSE-2.0 + + Unless required by applicable law or agreed to in writing, software + distributed under the License is distributed on an "AS IS" BASIS, + WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. + See the License for the specific language governing permissions and + limitations under the License. +*/ + +/** + * @file templates/chconf.h + * @brief Configuration file template. + * @details A copy of this file must be placed in each project directory, it + * contains the application specific kernel settings. + * + * @addtogroup config + * @details Kernel related settings and hooks. + * @{ + */ + +#ifndef CHCONF_H +#define CHCONF_H + +#define _CHIBIOS_RT_CONF_ + +/*===========================================================================*/ +/** + * @name System timers settings + * @{ + */ +/*===========================================================================*/ + +/** + * @brief System time counter resolution. + * @note Allowed values are 16 or 32 bits. + */ +#define CH_CFG_ST_RESOLUTION 32 + +/** + * @brief System tick frequency. + * @details Frequency of the system timer that drives the system ticks. This + * setting also defines the system tick time unit. + */ +#define CH_CFG_ST_FREQUENCY 100000 + +/** + * @brief Time delta constant for the tick-less mode. + * @note If this value is zero then the system uses the classic + * periodic tick. This value represents the minimum number + * of ticks that is safe to specify in a timeout directive. + * The value one is not valid, timeouts are rounded up to + * this value. + */ +#define CH_CFG_ST_TIMEDELTA 2 + +/** @} */ + +/*===========================================================================*/ +/** + * @name Kernel parameters and options + * @{ + */ +/*===========================================================================*/ + +/** + * @brief Round robin interval. + * @details This constant is the number of system ticks allowed for the + * threads before preemption occurs. Setting this value to zero + * disables the preemption for threads with equal priority and the + * round robin becomes cooperative. Note that higher priority + * threads can still preempt, the kernel is always preemptive. + * @note Disabling the round robin preemption makes the kernel more compact + * and generally faster. + * @note The round robin preemption is not supported in tickless mode and + * must be set to zero in that case. + */ +#define CH_CFG_TIME_QUANTUM 0 + +/** + * @brief Managed RAM size. + * @details Size of the RAM area to be managed by the OS. If set to zero + * then the whole available RAM is used. The core memory is made + * available to the heap allocator and/or can be used directly through + * the simplified core memory allocator. + * + * @note In order to let the OS manage the whole RAM the linker script must + * provide the @p __heap_base__ and @p __heap_end__ symbols. + * @note Requires @p CH_CFG_USE_MEMCORE. + */ +#define CH_CFG_MEMCORE_SIZE 0 + +/** + * @brief Idle thread automatic spawn suppression. + * @details When this option is activated the function @p chSysInit() + * does not spawn the idle thread. The application @p main() + * function becomes the idle thread and must implement an + * infinite loop. + */ +#define CH_CFG_NO_IDLE_THREAD FALSE + +/** @} */ + +/*===========================================================================*/ +/** + * @name Performance options + * @{ + */ +/*===========================================================================*/ + +/** + * @brief OS optimization. + * @details If enabled then time efficient rather than space efficient code + * is used when two possible implementations exist. + * + * @note This is not related to the compiler optimization options. + * @note The default is @p TRUE. + */ +#define CH_CFG_OPTIMIZE_SPEED TRUE + +/** @} */ + +/*===========================================================================*/ +/** + * @name Subsystem options + * @{ + */ +/*===========================================================================*/ + +/** + * @brief Time Measurement APIs. + * @details If enabled then the time measurement APIs are included in + * the kernel. + * + * @note The default is @p TRUE. + */ +#define CH_CFG_USE_TM TRUE + +/** + * @brief Threads registry APIs. + * @details If enabled then the registry APIs are included in the kernel. + * + * @note The default is @p TRUE. + */ +#define CH_CFG_USE_REGISTRY TRUE + +/** + * @brief Threads synchronization APIs. + * @details If enabled then the @p chThdWait() function is included in + * the kernel. + * + * @note The default is @p TRUE. + */ +#define CH_CFG_USE_WAITEXIT TRUE + +/** + * @brief Semaphores APIs. + * @details If enabled then the Semaphores APIs are included in the kernel. + * + * @note The default is @p TRUE. + */ +#define CH_CFG_USE_SEMAPHORES TRUE + +/** + * @brief Semaphores queuing mode. + * @details If enabled then the threads are enqueued on semaphores by + * priority rather than in FIFO order. + * + * @note The default is @p FALSE. Enable this if you have special + * requirements. + * @note Requires @p CH_CFG_USE_SEMAPHORES. + */ +#define CH_CFG_USE_SEMAPHORES_PRIORITY FALSE + +/** + * @brief Mutexes APIs. + * @details If enabled then the mutexes APIs are included in the kernel. + * + * @note The default is @p TRUE. + */ +#define CH_CFG_USE_MUTEXES TRUE + +/** + * @brief Enables recursive behavior on mutexes. + * @note Recursive mutexes are heavier and have an increased + * memory footprint. + * + * @note The default is @p FALSE. + * @note Requires @p CH_CFG_USE_MUTEXES. + */ +#define CH_CFG_USE_MUTEXES_RECURSIVE FALSE + +/** + * @brief Conditional Variables APIs. + * @details If enabled then the conditional variables APIs are included + * in the kernel. + * + * @note The default is @p TRUE. + * @note Requires @p CH_CFG_USE_MUTEXES. + */ +#define CH_CFG_USE_CONDVARS TRUE + +/** + * @brief Conditional Variables APIs with timeout. + * @details If enabled then the conditional variables APIs with timeout + * specification are included in the kernel. + * + * @note The default is @p TRUE. + * @note Requires @p CH_CFG_USE_CONDVARS. + */ +#define CH_CFG_USE_CONDVARS_TIMEOUT TRUE + +/** + * @brief Events Flags APIs. + * @details If enabled then the event flags APIs are included in the kernel. + * + * @note The default is @p TRUE. + */ +#define CH_CFG_USE_EVENTS TRUE + +/** + * @brief Events Flags APIs with timeout. + * @details If enabled then the events APIs with timeout specification + * are included in the kernel. + * + * @note The default is @p TRUE. + * @note Requires @p CH_CFG_USE_EVENTS. + */ +#define CH_CFG_USE_EVENTS_TIMEOUT TRUE + +/** + * @brief Synchronous Messages APIs. + * @details If enabled then the synchronous messages APIs are included + * in the kernel. + * + * @note The default is @p TRUE. + */ +#define CH_CFG_USE_MESSAGES TRUE + +/** + * @brief Synchronous Messages queuing mode. + * @details If enabled then messages are served by priority rather than in + * FIFO order. + * + * @note The default is @p FALSE. Enable this if you have special + * requirements. + * @note Requires @p CH_CFG_USE_MESSAGES. + */ +#define CH_CFG_USE_MESSAGES_PRIORITY TRUE + +/** + * @brief Mailboxes APIs. + * @details If enabled then the asynchronous messages (mailboxes) APIs are + * included in the kernel. + * + * @note The default is @p TRUE. + * @note Requires @p CH_CFG_USE_SEMAPHORES. + */ +#define CH_CFG_USE_MAILBOXES TRUE + +/** + * @brief Core Memory Manager APIs. + * @details If enabled then the core memory manager APIs are included + * in the kernel. + * + * @note The default is @p TRUE. + */ +#define CH_CFG_USE_MEMCORE TRUE + +/** + * @brief Heap Allocator APIs. + * @details If enabled then the memory heap allocator APIs are included + * in the kernel. + * + * @note The default is @p TRUE. + * @note Requires @p CH_CFG_USE_MEMCORE and either @p CH_CFG_USE_MUTEXES or + * @p CH_CFG_USE_SEMAPHORES. + * @note Mutexes are recommended. + */ +#define CH_CFG_USE_HEAP TRUE + +/** + * @brief Memory Pools Allocator APIs. + * @details If enabled then the memory pools allocator APIs are included + * in the kernel. + * + * @note The default is @p TRUE. + */ +#define CH_CFG_USE_MEMPOOLS TRUE + +/** + * @brief Dynamic Threads APIs. + * @details If enabled then the dynamic threads creation APIs are included + * in the kernel. + * + * @note The default is @p TRUE. + * @note Requires @p CH_CFG_USE_WAITEXIT. + * @note Requires @p CH_CFG_USE_HEAP and/or @p CH_CFG_USE_MEMPOOLS. + */ +#define CH_CFG_USE_DYNAMIC TRUE + +/** @} */ + +/*===========================================================================*/ +/** + * @name Debug options + * @{ + */ +/*===========================================================================*/ + +/** + * @brief Debug option, kernel statistics. + * + * @note The default is @p FALSE. + */ +#define CH_DBG_STATISTICS FALSE + +/** + * @brief Debug option, system state check. + * @details If enabled the correct call protocol for system APIs is checked + * at runtime. + * + * @note The default is @p FALSE. + */ +#define CH_DBG_SYSTEM_STATE_CHECK FALSE + +/** + * @brief Debug option, parameters checks. + * @details If enabled then the checks on the API functions input + * parameters are activated. + * + * @note The default is @p FALSE. + */ +#define CH_DBG_ENABLE_CHECKS FALSE + +/** + * @brief Debug option, consistency checks. + * @details If enabled then all the assertions in the kernel code are + * activated. This includes consistency checks inside the kernel, + * runtime anomalies and port-defined checks. + * + * @note The default is @p FALSE. + */ +#define CH_DBG_ENABLE_ASSERTS FALSE + +/** + * @brief Debug option, trace buffer. + * @details If enabled then the trace buffer is activated. + * + * @note The default is @p CH_DBG_TRACE_MASK_DISABLED. + */ +#define CH_DBG_TRACE_MASK CH_DBG_TRACE_MASK_DISABLED + +/** + * @brief Trace buffer entries. + * @note The trace buffer is only allocated if @p CH_DBG_TRACE_MASK is + * different from @p CH_DBG_TRACE_MASK_DISABLED. + */ +#define CH_DBG_TRACE_BUFFER_SIZE 128 + +/** + * @brief Debug option, stack checks. + * @details If enabled then a runtime stack check is performed. + * + * @note The default is @p FALSE. + * @note The stack check is performed in a architecture/port dependent way. + * It may not be implemented or some ports. + * @note The default failure mode is to halt the system with the global + * @p panic_msg variable set to @p NULL. + */ +#define CH_DBG_ENABLE_STACK_CHECK TRUE + +/** + * @brief Debug option, stacks initialization. + * @details If enabled then the threads working area is filled with a byte + * value when a thread is created. This can be useful for the + * runtime measurement of the used stack. + * + * @note The default is @p FALSE. + */ +#define CH_DBG_FILL_THREADS FALSE + +/** + * @brief Debug option, threads profiling. + * @details If enabled then a field is added to the @p thread_t structure that + * counts the system ticks occurred while executing the thread. + * + * @note The default is @p FALSE. + * @note This debug option is not currently compatible with the + * tickless mode. + */ +#define CH_DBG_THREADS_PROFILING FALSE + +/** @} */ + +/*===========================================================================*/ +/** + * @name Kernel hooks + * @{ + */ +/*===========================================================================*/ + +/** + * @brief Threads descriptor structure extension. + * @details User fields added to the end of the @p thread_t structure. + */ +#define CH_CFG_THREAD_EXTRA_FIELDS \ + /* Add threads custom fields here.*/ + +/** + * @brief Threads initialization hook. + * @details User initialization code added to the @p chThdInit() API. + * + * @note It is invoked from within @p chThdInit() and implicitly from all + * the threads creation APIs. + */ +#define CH_CFG_THREAD_INIT_HOOK(tp) { \ + /* Add threads initialization code here.*/ \ +} + +/** + * @brief Threads finalization hook. + * @details User finalization code added to the @p chThdExit() API. + */ +#define CH_CFG_THREAD_EXIT_HOOK(tp) { \ + /* Add threads finalization code here.*/ \ +} + +/** + * @brief Context switch hook. + * @details This hook is invoked just before switching between threads. + */ +#define CH_CFG_CONTEXT_SWITCH_HOOK(ntp, otp) { \ + /* Context switch code here.*/ \ +} + +/** + * @brief ISR enter hook. + */ +#define CH_CFG_IRQ_PROLOGUE_HOOK() { \ + /* IRQ prologue code here.*/ \ +} + +/** + * @brief ISR exit hook. + */ +#define CH_CFG_IRQ_EPILOGUE_HOOK() { \ + /* IRQ epilogue code here.*/ \ +} + +/** + * @brief Idle thread enter hook. + * @note This hook is invoked within a critical zone, no OS functions + * should be invoked from here. + * @note This macro can be used to activate a power saving mode. + */ +#define CH_CFG_IDLE_ENTER_HOOK() { \ + /* Idle-enter code here.*/ \ +} + +/** + * @brief Idle thread leave hook. + * @note This hook is invoked within a critical zone, no OS functions + * should be invoked from here. + * @note This macro can be used to deactivate a power saving mode. + */ +#define CH_CFG_IDLE_LEAVE_HOOK() { \ + /* Idle-leave code here.*/ \ +} + +/** + * @brief Idle Loop hook. + * @details This hook is continuously invoked by the idle thread loop. + */ +#define CH_CFG_IDLE_LOOP_HOOK() { \ + /* Idle loop code here.*/ \ +} + +/** + * @brief System tick event hook. + * @details This hook is invoked in the system tick handler immediately + * after processing the virtual timers queue. + */ +#define CH_CFG_SYSTEM_TICK_HOOK() { \ + /* System tick event code here.*/ \ +} + +/** + * @brief System halt hook. + * @details This hook is invoked in case to a system halting error before + * the system is halted. + */ +#define CH_CFG_SYSTEM_HALT_HOOK(reason) { \ + /* System halt code here.*/ \ +} + +/** + * @brief Trace hook. + * @details This hook is invoked each time a new record is written in the + * trace buffer. + */ +#define CH_CFG_TRACE_HOOK(tep) { \ + /* Trace code here.*/ \ +} + +/** @} */ + +/*===========================================================================*/ +/* Port-specific settings (override port settings defaulted in chcore.h). */ +/*===========================================================================*/ + +#endif /* CHCONF_H */ + +/** @} */ diff --git a/keyboards/handwired/co60/rev6/config.h b/keyboards/handwired/co60/rev6/config.h new file mode 100644 index 000000000..b1ab99fd9 --- /dev/null +++ b/keyboards/handwired/co60/rev6/config.h @@ -0,0 +1,60 @@ +/* + * Copyright 2019 John M Daly <jmdaly@gmail.com> + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ +#pragma once + +#include "config_common.h" + +/* USB Device descriptor parameter */ +#define VENDOR_ID 0xFEED +#define PRODUCT_ID 0x0000 +#define DEVICE_VER 0x0001 +#define MANUFACTURER John M Daly +#define PRODUCT CO60 rev6 +#define DESCRIPTION An open hardware sixty percent PCB + +/* Address for jumping to bootloader on STM32 chips. */ +/* It is chip dependent, the correct number can be looked up here: + * http://www.st.com/web/en/resource/technical/document/application_note/CD00167594.pdf + */ +#define STM32_BOOTLOADER_ADDRESS 0x1FFFD800 + +/* key matrix size */ +#define MATRIX_ROWS 5 +#define MATRIX_COLS 15 + +/* ROWS: Top to bottom, COLS: Left to right +*/ +#define MATRIX_ROW_PINS { B0, B1, B2, A15, A10 } +#define MATRIX_COL_PINS { A2, A3, A6, B14, B15, A8, A9, A7, B3, B4, C14, C15, C13, B5, B6 } + +/* COL2ROW, ROW2COL, or CUSTOM_MATRIX */ +#define DIODE_DIRECTION COL2ROW + +/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */ +#define DEBOUNCE 5 + +/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ +#define LOCKING_SUPPORT_ENABLE +/* Locking resynchronize hack */ +#define LOCKING_RESYNC_ENABLE + +/* Backlight configuration + * Backlight LEDs on B8 + */ +#define BACKLIGHT_LEVELS 24 +#define BACKLIGHT_BREATHING +#define BREATHING_PERIOD 6 diff --git a/keyboards/handwired/co60/rev6/halconf.h b/keyboards/handwired/co60/rev6/halconf.h new file mode 100644 index 000000000..5e5d70219 --- /dev/null +++ b/keyboards/handwired/co60/rev6/halconf.h @@ -0,0 +1,388 @@ +/* + ChibiOS - Copyright (C) 2006..2016 Giovanni Di Sirio + + Licensed under the Apache License, Version 2.0 (the "License"); + you may not use this file except in compliance with the License. + You may obtain a copy of the License at + + http://www.apache.org/licenses/LICENSE-2.0 + + Unless required by applicable law or agreed to in writing, software + distributed under the License is distributed on an "AS IS" BASIS, + WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. + See the License for the specific language governing permissions and + limitations under the License. +*/ + +/** + * @file templates/halconf.h + * @brief HAL configuration header. + * @details HAL configuration file, this file allows to enable or disable the + * various device drivers from your application. You may also use + * this file in order to override the device drivers default settings. + * + * @addtogroup HAL_CONF + * @{ + */ + +#ifndef HALCONF_H +#define HALCONF_H + +#include "mcuconf.h" + +/** + * @brief Enables the PAL subsystem. + */ +#if !defined(HAL_USE_PAL) || defined(__DOXYGEN__) +#define HAL_USE_PAL TRUE +#endif + +/** + * @brief Enables the ADC subsystem. + */ +#if !defined(HAL_USE_ADC) || defined(__DOXYGEN__) +#define HAL_USE_ADC FALSE +#endif + +/** + * @brief Enables the CAN subsystem. + */ +#if !defined(HAL_USE_CAN) || defined(__DOXYGEN__) +#define HAL_USE_CAN FALSE +#endif + +/** + * @brief Enables the DAC subsystem. + */ +#if !defined(HAL_USE_DAC) || defined(__DOXYGEN__) +#define HAL_USE_DAC TRUE +#endif + +/** + * @brief Enables the EXT subsystem. + */ +#if !defined(HAL_USE_EXT) || defined(__DOXYGEN__) +#define HAL_USE_EXT FALSE +#endif + +/** + * @brief Enables the GPT subsystem. + */ +#if !defined(HAL_USE_GPT) || defined(__DOXYGEN__) +#define HAL_USE_GPT TRUE +#endif + +/** + * @brief Enables the I2C subsystem. + */ +#if !defined(HAL_USE_I2C) || defined(__DOXYGEN__) +#define HAL_USE_I2C FALSE +#endif + +/** + * @brief Enables the I2S subsystem. + */ +#if !defined(HAL_USE_I2S) || defined(__DOXYGEN__) +#define HAL_USE_I2S FALSE +#endif + +/** + * @brief Enables the ICU subsystem. + */ +#if !defined(HAL_USE_ICU) || defined(__DOXYGEN__) +#define HAL_USE_ICU FALSE +#endif + +/** + * @brief Enables the MAC subsystem. + */ +#if !defined(HAL_USE_MAC) || defined(__DOXYGEN__) +#define HAL_USE_MAC FALSE +#endif + +/** + * @brief Enables the MMC_SPI subsystem. + */ +#if !defined(HAL_USE_MMC_SPI) || defined(__DOXYGEN__) +#define HAL_USE_MMC_SPI FALSE +#endif + +/** + * @brief Enables the PWM subsystem. + */ +#if !defined(HAL_USE_PWM) || defined(__DOXYGEN__) +#define HAL_USE_PWM TRUE +#endif + +/** + * @brief Enables the QSPI subsystem. + */ +#if !defined(HAL_USE_QSPI) || defined(__DOXYGEN__) +#define HAL_USE_QSPI FALSE +#endif + +/** + * @brief Enables the RTC subsystem. + */ +#if !defined(HAL_USE_RTC) || defined(__DOXYGEN__) +#define HAL_USE_RTC FALSE +#endif + +/** + * @brief Enables the SDC subsystem. + */ +#if !defined(HAL_USE_SDC) || defined(__DOXYGEN__) +#define HAL_USE_SDC FALSE +#endif + +/** + * @brief Enables the SERIAL subsystem. + */ +#if !defined(HAL_USE_SERIAL) || defined(__DOXYGEN__) +#define HAL_USE_SERIAL FALSE +#endif + +/** + * @brief Enables the SERIAL over USB subsystem. + */ +#if !defined(HAL_USE_SERIAL_USB) || defined(__DOXYGEN__) +#define HAL_USE_SERIAL_USB TRUE +#endif + +/** + * @brief Enables the SPI subsystem. + */ +#if !defined(HAL_USE_SPI) || defined(__DOXYGEN__) +#define HAL_USE_SPI FALSE +#endif + +/** + * @brief Enables the UART subsystem. + */ +#if !defined(HAL_USE_UART) || defined(__DOXYGEN__) +#define HAL_USE_UART FALSE +#endif + +/** + * @brief Enables the USB subsystem. + */ +#if !defined(HAL_USE_USB) || defined(__DOXYGEN__) +#define HAL_USE_USB TRUE +#endif + +/** + * @brief Enables the WDG subsystem. + */ +#if !defined(HAL_USE_WDG) || defined(__DOXYGEN__) +#define HAL_USE_WDG FALSE +#endif + +/*===========================================================================*/ +/* ADC driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Enables synchronous APIs. + * @note Disabling this option saves both code and data space. + */ +#if !defined(ADC_USE_WAIT) || defined(__DOXYGEN__) +#define ADC_USE_WAIT TRUE +#endif + +/** + * @brief Enables the @p adcAcquireBus() and @p adcReleaseBus() APIs. + * @note Disabling this option saves both code and data space. + */ +#if !defined(ADC_USE_MUTUAL_EXCLUSION) || defined(__DOXYGEN__) +#define ADC_USE_MUTUAL_EXCLUSION TRUE +#endif + +/*===========================================================================*/ +/* CAN driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Sleep mode related APIs inclusion switch. + */ +#if !defined(CAN_USE_SLEEP_MODE) || defined(__DOXYGEN__) +#define CAN_USE_SLEEP_MODE TRUE +#endif + +/*===========================================================================*/ +/* I2C driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Enables the mutual exclusion APIs on the I2C bus. + */ +#if !defined(I2C_USE_MUTUAL_EXCLUSION) || defined(__DOXYGEN__) +#define I2C_USE_MUTUAL_EXCLUSION TRUE +#endif + +/*===========================================================================*/ +/* MAC driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Enables an event sources for incoming packets. + */ +#if !defined(MAC_USE_ZERO_COPY) || defined(__DOXYGEN__) +#define MAC_USE_ZERO_COPY FALSE +#endif + +/** + * @brief Enables an event sources for incoming packets. + */ +#if !defined(MAC_USE_EVENTS) || defined(__DOXYGEN__) +#define MAC_USE_EVENTS TRUE +#endif + +/*===========================================================================*/ +/* MMC_SPI driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Delays insertions. + * @details If enabled this options inserts delays into the MMC waiting + * routines releasing some extra CPU time for the threads with + * lower priority, this may slow down the driver a bit however. + * This option is recommended also if the SPI driver does not + * use a DMA channel and heavily loads the CPU. + */ +#if !defined(MMC_NICE_WAITING) || defined(__DOXYGEN__) +#define MMC_NICE_WAITING TRUE +#endif + +/*===========================================================================*/ +/* SDC driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Number of initialization attempts before rejecting the card. + * @note Attempts are performed at 10mS intervals. + */ +#if !defined(SDC_INIT_RETRY) || defined(__DOXYGEN__) +#define SDC_INIT_RETRY 100 +#endif + +/** + * @brief Include support for MMC cards. + * @note MMC support is not yet implemented so this option must be kept + * at @p FALSE. + */ +#if !defined(SDC_MMC_SUPPORT) || defined(__DOXYGEN__) +#define SDC_MMC_SUPPORT FALSE +#endif + +/** + * @brief Delays insertions. + * @details If enabled this options inserts delays into the MMC waiting + * routines releasing some extra CPU time for the threads with + * lower priority, this may slow down the driver a bit however. + */ +#if !defined(SDC_NICE_WAITING) || defined(__DOXYGEN__) +#define SDC_NICE_WAITING TRUE +#endif + +/*===========================================================================*/ +/* SERIAL driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Default bit rate. + * @details Configuration parameter, this is the baud rate selected for the + * default configuration. + */ +#if !defined(SERIAL_DEFAULT_BITRATE) || defined(__DOXYGEN__) +#define SERIAL_DEFAULT_BITRATE 38400 +#endif + +/** + * @brief Serial buffers size. + * @details Configuration parameter, you can change the depth of the queue + * buffers depending on the requirements of your application. + * @note The default is 16 bytes for both the transmission and receive + * buffers. + */ +#if !defined(SERIAL_BUFFERS_SIZE) || defined(__DOXYGEN__) +#define SERIAL_BUFFERS_SIZE 16 +#endif + +/*===========================================================================*/ +/* SERIAL_USB driver related setting. */ +/*===========================================================================*/ + +/** + * @brief Serial over USB buffers size. + * @details Configuration parameter, the buffer size must be a multiple of + * the USB data endpoint maximum packet size. + * @note The default is 256 bytes for both the transmission and receive + * buffers. + */ +#if !defined(SERIAL_USB_BUFFERS_SIZE) || defined(__DOXYGEN__) +#define SERIAL_USB_BUFFERS_SIZE 1 +#endif + +/** + * @brief Serial over USB number of buffers. + * @note The default is 2 buffers. + */ +#if !defined(SERIAL_USB_BUFFERS_NUMBER) || defined(__DOXYGEN__) +#define SERIAL_USB_BUFFERS_NUMBER 2 +#endif + +/*===========================================================================*/ +/* SPI driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Enables synchronous APIs. + * @note Disabling this option saves both code and data space. + */ +#if !defined(SPI_USE_WAIT) || defined(__DOXYGEN__) +#define SPI_USE_WAIT TRUE +#endif + +/** + * @brief Enables the @p spiAcquireBus() and @p spiReleaseBus() APIs. + * @note Disabling this option saves both code and data space. + */ +#if !defined(SPI_USE_MUTUAL_EXCLUSION) || defined(__DOXYGEN__) +#define SPI_USE_MUTUAL_EXCLUSION TRUE +#endif + +/*===========================================================================*/ +/* UART driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Enables synchronous APIs. + * @note Disabling this option saves both code and data space. + */ +#if !defined(UART_USE_WAIT) || defined(__DOXYGEN__) +#define UART_USE_WAIT FALSE +#endif + +/** + * @brief Enables the @p uartAcquireBus() and @p uartReleaseBus() APIs. + * @note Disabling this option saves both code and data space. + */ +#if !defined(UART_USE_MUTUAL_EXCLUSION) || defined(__DOXYGEN__) +#define UART_USE_MUTUAL_EXCLUSION FALSE +#endif + +/*===========================================================================*/ +/* USB driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Enables synchronous APIs. + * @note Disabling this option saves both code and data space. + */ +#if !defined(USB_USE_WAIT) || defined(__DOXYGEN__) +#define USB_USE_WAIT TRUE +#endif + +#endif /* HALCONF_H */ + +/** @} */ diff --git a/keyboards/handwired/co60/rev6/led.c b/keyboards/handwired/co60/rev6/led.c new file mode 100644 index 000000000..fe28ce2e8 --- /dev/null +++ b/keyboards/handwired/co60/rev6/led.c @@ -0,0 +1,240 @@ +/* +Copyright 2012 Jun Wako <wakojun@gmail.com> + +This program is free software: you can redistribute it and/or modify +it under the terms of the GNU General Public License as published by +the Free Software Foundation, either version 2 of the License, or +(at your option) any later version. + +This program is distributed in the hope that it will be useful, +but WITHOUT ANY WARRANTY; without even the implied warranty of +MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +GNU General Public License for more details. + +You should have received a copy of the GNU General Public License +along with this program. If not, see <http://www.gnu.org/licenses/>. +*/ + +#include "hal.h" +#include "led_custom.h" +#include "rev6.h" +#include "printf.h" + +static void breathing_callback(PWMDriver *pwmp); + +static PWMConfig pwmCFG = { + 0xFFFF, /* PWM clock frequency */ + 256, /* PWM period (in ticks) 1S (1/10kHz=0.1mS 0.1ms*10000 ticks=1S) */ + NULL, /* No Callback */ + { + {PWM_OUTPUT_DISABLED, NULL}, + {PWM_OUTPUT_DISABLED, NULL}, + {PWM_OUTPUT_ACTIVE_HIGH, NULL}, /* Enable Channel 3 */ + {PWM_OUTPUT_DISABLED, NULL} + }, + 0, /* HW dependent part.*/ + 0 +}; + +static PWMConfig pwmCFG_breathing = { + 0xFFFF, /* 10kHz PWM clock frequency */ + 256, /* PWM period (in ticks) 1S (1/10kHz=0.1mS 0.1ms*10000 ticks=1S) */ + breathing_callback, /* Breathing Callback */ + { + {PWM_OUTPUT_DISABLED, NULL}, + {PWM_OUTPUT_DISABLED, NULL}, + {PWM_OUTPUT_ACTIVE_HIGH, NULL}, /* Enable Channel 3 */ + {PWM_OUTPUT_DISABLED, NULL} + }, + 0, /* HW dependent part.*/ + 0 +}; + +// See http://jared.geek.nz/2013/feb/linear-led-pwm +static uint16_t cie_lightness(uint16_t v) { + if (v <= 5243) // if below 8% of max + return v / 9; // same as dividing by 900% + else { + uint32_t y = (((uint32_t)v + 10486) << 8) / (10486 + 0xFFFFUL); // add 16% of max and compare + // to get a useful result with integer division, we shift left in the expression above + // and revert what we've done again after squaring. + y = y * y * y >> 8; + if (y > 0xFFFFUL) // prevent overflow + return 0xFFFFU; + else + return (uint16_t)y; + } +} + +void backlight_init_ports(void) { + palSetPadMode(GPIOB, 8, PAL_MODE_ALTERNATE(2)); + pwmStart(&PWMD4, &pwmCFG); + if (kb_backlight_config.enable) { + if (kb_backlight_config.breathing) { + breathing_enable(); + } else { + backlight_set(kb_backlight_config.level); + } + } else { + backlight_set(0); + } +} + +void backlight_set(uint8_t level) { + uint32_t duty = (uint32_t)(cie_lightness(0xFFFF * (uint32_t)level / BACKLIGHT_LEVELS)); + if (level == 0) { + // Turn backlight off + // Disable channel 3 on PWM4 + pwmDisableChannel(&PWMD4, 2); + } else { + // Turn backlight on + if (!is_breathing()) { + // Enable channel 3 on PWM4 + pwmEnableChannel(&PWMD4, 2, PWM_FRACTION_TO_WIDTH(&PWMD4, 0xFFFF, duty)); + } + } +} + +uint8_t backlight_tick = 0; + +void backlight_task(void) { +} + +#define BREATHING_NO_HALT 0 +#define BREATHING_HALT_OFF 1 +#define BREATHING_HALT_ON 2 +#define BREATHING_STEPS 128 + +static uint8_t breathing_period = BREATHING_PERIOD; +static uint8_t breathing_halt = BREATHING_NO_HALT; +static uint16_t breathing_counter = 0; + +bool is_breathing(void) { + return PWMD4.config == &pwmCFG_breathing; +} + +#define breathing_min() do {breathing_counter = 0;} while (0) +#define breathing_max() do {breathing_counter = breathing_period * 256 / 2;} while (0) + + +void breathing_interrupt_enable(void){ + pwmStop(&PWMD4); + pwmStart(&PWMD4, &pwmCFG_breathing); + chSysLockFromISR(); + pwmEnablePeriodicNotification(&PWMD4); + pwmEnableChannelI( + &PWMD4, + 2, + PWM_FRACTION_TO_WIDTH( + &PWMD4, + 0xFFFF, + 0xFFFF + ) + ); + chSysUnlockFromISR(); +} + +void breathing_interrupt_disable(void){ + pwmStop(&PWMD4); + pwmStart(&PWMD4, &pwmCFG); +} + +void breathing_enable(void) +{ + breathing_counter = 0; + breathing_halt = BREATHING_NO_HALT; + breathing_interrupt_enable(); +} + +void breathing_pulse(void) +{ + if (kb_backlight_config.level == 0) + breathing_min(); + else + breathing_max(); + breathing_halt = BREATHING_HALT_ON; + breathing_interrupt_enable(); +} + +void breathing_disable(void) +{ + breathing_interrupt_disable(); + // Restore backlight level + backlight_set(kb_backlight_config.level); +} + +void breathing_self_disable(void) +{ + if (kb_backlight_config.level == 0) + breathing_halt = BREATHING_HALT_OFF; + else + breathing_halt = BREATHING_HALT_ON; +} + +void breathing_toggle(void) { + if (is_breathing()){ + breathing_disable(); + } else { + breathing_enable(); + } +} + +void breathing_period_set(uint8_t value) +{ + if (!value) + value = 1; + breathing_period = value; +} + +void breathing_period_default(void) { + breathing_period_set(BREATHING_PERIOD); +} + +void breathing_period_inc(void) +{ + breathing_period_set(breathing_period+1); +} + +void breathing_period_dec(void) +{ + breathing_period_set(breathing_period-1); +} + +/* To generate breathing curve in python: + * from math import sin, pi; [int(sin(x/128.0*pi)**4*255) for x in range(128)] + */ +static const uint8_t breathing_table[BREATHING_STEPS] = {0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 1, 1, 2, 3, 4, 5, 6, 8, 10, 12, 15, 17, 20, 24, 28, 32, 36, 41, 46, 51, 57, 63, 70, 76, 83, 91, 98, 106, 113, 121, 129, 138, 146, 154, 162, 170, 178, 185, 193, 200, 207, 213, 220, 225, 231, 235, 240, 244, 247, 250, 252, 253, 254, 255, 254, 253, 252, 250, 247, 244, 240, 235, 231, 225, 220, 213, 207, 200, 193, 185, 178, 170, 162, 154, 146, 138, 129, 121, 113, 106, 98, 91, 83, 76, 70, 63, 57, 51, 46, 41, 36, 32, 28, 24, 20, 17, 15, 12, 10, 8, 6, 5, 4, 3, 2, 1, 1, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0}; + +// Use this before the cie_lightness function. +static inline uint16_t scale_backlight(uint16_t v) { + return v / BACKLIGHT_LEVELS * kb_backlight_config.level; +} + +static void breathing_callback(PWMDriver *pwmp) +{ + (void)pwmp; + uint16_t interval = (uint16_t) breathing_period * 256 / BREATHING_STEPS; + // resetting after one period to prevent ugly reset at overflow. + breathing_counter = (breathing_counter + 1) % (breathing_period * 256); + uint8_t index = breathing_counter / interval % BREATHING_STEPS; + + if (((breathing_halt == BREATHING_HALT_ON) && (index == BREATHING_STEPS / 2)) || + ((breathing_halt == BREATHING_HALT_OFF) && (index == BREATHING_STEPS - 1))) + { + breathing_interrupt_disable(); + } + + uint32_t duty = cie_lightness(scale_backlight(breathing_table[index] * 256)); + + chSysLockFromISR(); + pwmEnableChannelI( + &PWMD4, + 2, + PWM_FRACTION_TO_WIDTH( + &PWMD4, + 0xFFFF, + duty + ) + ); + chSysUnlockFromISR(); +} diff --git a/keyboards/handwired/co60/rev6/led_custom.h b/keyboards/handwired/co60/rev6/led_custom.h new file mode 100644 index 000000000..96c4d0c2b --- /dev/null +++ b/keyboards/handwired/co60/rev6/led_custom.h @@ -0,0 +1,22 @@ +/* + * Copyright 2019 John M Daly <jmdaly@gmail.com> + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#pragma once + +void backlight_task(void); +void breathing_interrupt_disable(void); +void breathing_interrupt_enable(void); diff --git a/keyboards/handwired/co60/rev6/mcuconf.h b/keyboards/handwired/co60/rev6/mcuconf.h new file mode 100644 index 000000000..69bf9185d --- /dev/null +++ b/keyboards/handwired/co60/rev6/mcuconf.h @@ -0,0 +1,257 @@ +/* + ChibiOS - Copyright (C) 2006..2016 Giovanni Di Sirio + + Licensed under the Apache License, Version 2.0 (the "License"); + you may not use this file except in compliance with the License. + You may obtain a copy of the License at + + http://www.apache.org/licenses/LICENSE-2.0 + + Unless required by applicable law or agreed to in writing, software + distributed under the License is distributed on an "AS IS" BASIS, + WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. + See the License for the specific language governing permissions and + limitations under the License. +*/ + +#ifndef MCUCONF_H +#define MCUCONF_H + +/* + * STM32F3xx drivers configuration. + * The following settings override the default settings present in + * the various device driver implementation headers. + * Note that the settings for each driver only have effect if the whole + * driver is enabled in halconf.h. + * + * IRQ priorities: + * 15...0 Lowest...Highest. + * + * DMA priorities: + * 0...3 Lowest...Highest. + */ + +#define STM32F3xx_MCUCONF + +/* + * HAL driver system settings. + */ +#define STM32_NO_INIT FALSE +#define STM32_PVD_ENABLE FALSE +#define STM32_PLS STM32_PLS_LEV0 +#define STM32_HSI_ENABLED TRUE +#define STM32_LSI_ENABLED TRUE +#define STM32_HSE_ENABLED TRUE +#define STM32_LSE_ENABLED FALSE +#define STM32_SW STM32_SW_PLL +#define STM32_PLLSRC STM32_PLLSRC_HSE +#define STM32_PREDIV_VALUE 1 +#define STM32_PLLMUL_VALUE 9 +#define STM32_HPRE STM32_HPRE_DIV1 +#define STM32_PPRE1 STM32_PPRE1_DIV2 +#define STM32_PPRE2 STM32_PPRE2_DIV2 +#define STM32_MCOSEL STM32_MCOSEL_NOCLOCK +#define STM32_ADC12PRES STM32_ADC12PRES_DIV1 +#define STM32_ADC34PRES STM32_ADC34PRES_DIV1 +#define STM32_USART1SW STM32_USART1SW_PCLK +#define STM32_USART2SW STM32_USART2SW_PCLK +#define STM32_USART3SW STM32_USART3SW_PCLK +#define STM32_UART4SW STM32_UART4SW_PCLK +#define STM32_UART5SW STM32_UART5SW_PCLK +#define STM32_I2C1SW STM32_I2C1SW_SYSCLK +#define STM32_I2C2SW STM32_I2C2SW_SYSCLK +#define STM32_TIM1SW STM32_TIM1SW_PCLK2 +#define STM32_TIM8SW STM32_TIM8SW_PCLK2 +#define STM32_RTCSEL STM32_RTCSEL_LSI +#define STM32_USB_CLOCK_REQUIRED TRUE +#define STM32_USBPRE STM32_USBPRE_DIV1P5 + +#undef STM32_HSE_BYPASS +// #error "oh no" +// #endif + +/* + * ADC driver system settings. + */ +#define STM32_ADC_DUAL_MODE FALSE +#define STM32_ADC_COMPACT_SAMPLES FALSE +#define STM32_ADC_USE_ADC1 FALSE +#define STM32_ADC_USE_ADC2 FALSE +#define STM32_ADC_USE_ADC3 FALSE +#define STM32_ADC_USE_ADC4 FALSE +#define STM32_ADC_ADC1_DMA_STREAM STM32_DMA_STREAM_ID(1, 1) +#define STM32_ADC_ADC2_DMA_STREAM STM32_DMA_STREAM_ID(2, 1) +#define STM32_ADC_ADC3_DMA_STREAM STM32_DMA_STREAM_ID(2, 5) +#define STM32_ADC_ADC4_DMA_STREAM STM32_DMA_STREAM_ID(2, 2) +#define STM32_ADC_ADC1_DMA_PRIORITY 2 +#define STM32_ADC_ADC2_DMA_PRIORITY 2 +#define STM32_ADC_ADC3_DMA_PRIORITY 2 +#define STM32_ADC_ADC4_DMA_PRIORITY 2 +#define STM32_ADC_ADC12_IRQ_PRIORITY 5 +#define STM32_ADC_ADC3_IRQ_PRIORITY 5 +#define STM32_ADC_ADC4_IRQ_PRIORITY 5 +#define STM32_ADC_ADC1_DMA_IRQ_PRIORITY 5 +#define STM32_ADC_ADC2_DMA_IRQ_PRIORITY 5 +#define STM32_ADC_ADC3_DMA_IRQ_PRIORITY 5 +#define STM32_ADC_ADC4_DMA_IRQ_PRIORITY 5 +#define STM32_ADC_ADC12_CLOCK_MODE ADC_CCR_CKMODE_AHB_DIV1 +#define STM32_ADC_ADC34_CLOCK_MODE ADC_CCR_CKMODE_AHB_DIV1 + +/* + * CAN driver system settings. + */ +#define STM32_CAN_USE_CAN1 FALSE +#define STM32_CAN_CAN1_IRQ_PRIORITY 11 + +/* + * DAC driver system settings. + */ +#define STM32_DAC_DUAL_MODE FALSE +#define STM32_DAC_USE_DAC1_CH1 TRUE +#define STM32_DAC_USE_DAC1_CH2 TRUE +#define STM32_DAC_DAC1_CH1_IRQ_PRIORITY 10 +#define STM32_DAC_DAC1_CH2_IRQ_PRIORITY 10 +#define STM32_DAC_DAC1_CH1_DMA_PRIORITY 2 +#define STM32_DAC_DAC1_CH2_DMA_PRIORITY 2 + +/* + * EXT driver system settings. + */ +#define STM32_EXT_EXTI0_IRQ_PRIORITY 6 +#define STM32_EXT_EXTI1_IRQ_PRIORITY 6 +#define STM32_EXT_EXTI2_IRQ_PRIORITY 6 +#define STM32_EXT_EXTI3_IRQ_PRIORITY 6 +#define STM32_EXT_EXTI4_IRQ_PRIORITY 6 +#define STM32_EXT_EXTI5_9_IRQ_PRIORITY 6 +#define STM32_EXT_EXTI10_15_IRQ_PRIORITY 6 +#define STM32_EXT_EXTI16_IRQ_PRIORITY 6 +#define STM32_EXT_EXTI17_IRQ_PRIORITY 6 +#define STM32_EXT_EXTI18_IRQ_PRIORITY 6 +#define STM32_EXT_EXTI19_IRQ_PRIORITY 6 +#define STM32_EXT_EXTI20_IRQ_PRIORITY 6 +#define STM32_EXT_EXTI21_22_29_IRQ_PRIORITY 6 +#define STM32_EXT_EXTI30_32_IRQ_PRIORITY 6 +#define STM32_EXT_EXTI33_IRQ_PRIORITY 6 + +/* + * GPT driver system settings. + */ +#define STM32_GPT_USE_TIM1 FALSE +#define STM32_GPT_USE_TIM2 FALSE +#define STM32_GPT_USE_TIM3 FALSE +#define STM32_GPT_USE_TIM4 FALSE +#define STM32_GPT_USE_TIM6 TRUE +#define STM32_GPT_USE_TIM7 TRUE +#define STM32_GPT_USE_TIM8 TRUE +#define STM32_GPT_TIM1_IRQ_PRIORITY 7 +#define STM32_GPT_TIM2_IRQ_PRIORITY 7 +#define STM32_GPT_TIM3_IRQ_PRIORITY 7 +#define STM32_GPT_TIM4_IRQ_PRIORITY 7 +#define STM32_GPT_TIM6_IRQ_PRIORITY 7 +#define STM32_GPT_TIM7_IRQ_PRIORITY 7 +#define STM32_GPT_TIM8_IRQ_PRIORITY 7 + +/* + * I2C driver system settings. + */ +#define STM32_I2C_USE_I2C1 FALSE +#define STM32_I2C_USE_I2C2 FALSE +#define STM32_I2C_BUSY_TIMEOUT 50 +#define STM32_I2C_I2C1_IRQ_PRIORITY 10 +#define STM32_I2C_I2C2_IRQ_PRIORITY 10 +#define STM32_I2C_USE_DMA TRUE +#define STM32_I2C_I2C1_DMA_PRIORITY 1 +#define STM32_I2C_I2C2_DMA_PRIORITY 1 +#define STM32_I2C_DMA_ERROR_HOOK(i2cp) osalSysHalt("DMA failure") + +/* + * ICU driver system settings. + */ +#define STM32_ICU_USE_TIM1 FALSE +#define STM32_ICU_USE_TIM2 FALSE +#define STM32_ICU_USE_TIM3 FALSE +#define STM32_ICU_USE_TIM4 FALSE +#define STM32_ICU_USE_TIM8 FALSE +#define STM32_ICU_TIM1_IRQ_PRIORITY 7 +#define STM32_ICU_TIM2_IRQ_PRIORITY 7 +#define STM32_ICU_TIM3_IRQ_PRIORITY 7 +#define STM32_ICU_TIM4_IRQ_PRIORITY 7 +#define STM32_ICU_TIM8_IRQ_PRIORITY 7 + +/* + * PWM driver system settings. + */ +#define STM32_PWM_USE_ADVANCED FALSE +#define STM32_PWM_USE_TIM1 FALSE +#define STM32_PWM_USE_TIM2 FALSE +#define STM32_PWM_USE_TIM3 FALSE +#define STM32_PWM_USE_TIM4 TRUE +#define STM32_PWM_USE_TIM8 FALSE +#define STM32_PWM_TIM1_IRQ_PRIORITY 7 +#define STM32_PWM_TIM2_IRQ_PRIORITY 7 +#define STM32_PWM_TIM3_IRQ_PRIORITY 7 +#define STM32_PWM_TIM4_IRQ_PRIORITY 7 +#define STM32_PWM_TIM8_IRQ_PRIORITY 7 + +/* + * SERIAL driver system settings. + */ +#define STM32_SERIAL_USE_USART1 FALSE +#define STM32_SERIAL_USE_USART2 TRUE +#define STM32_SERIAL_USE_USART3 FALSE +#define STM32_SERIAL_USE_UART4 FALSE +#define STM32_SERIAL_USE_UART5 FALSE +#define STM32_SERIAL_USART1_PRIORITY 12 +#define STM32_SERIAL_USART2_PRIORITY 12 +#define STM32_SERIAL_USART3_PRIORITY 12 +#define STM32_SERIAL_UART4_PRIORITY 12 +#define STM32_SERIAL_UART5_PRIORITY 12 + +/* + * SPI driver system settings. + */ +#define STM32_SPI_USE_SPI1 FALSE +#define STM32_SPI_USE_SPI2 FALSE +#define STM32_SPI_USE_SPI3 FALSE +#define STM32_SPI_SPI1_DMA_PRIORITY 1 +#define STM32_SPI_SPI2_DMA_PRIORITY 1 +#define STM32_SPI_SPI3_DMA_PRIORITY 1 +#define STM32_SPI_SPI1_IRQ_PRIORITY 10 +#define STM32_SPI_SPI2_IRQ_PRIORITY 10 +#define STM32_SPI_SPI3_IRQ_PRIORITY 10 +#define STM32_SPI_DMA_ERROR_HOOK(spip) osalSysHalt("DMA failure") + +/* + * ST driver system settings. + */ +#define STM32_ST_IRQ_PRIORITY 8 +#define STM32_ST_USE_TIMER 2 + +/* + * UART driver system settings. + */ +#define STM32_UART_USE_USART1 FALSE +#define STM32_UART_USE_USART2 FALSE +#define STM32_UART_USE_USART3 FALSE +#define STM32_UART_USART1_IRQ_PRIORITY 12 +#define STM32_UART_USART2_IRQ_PRIORITY 12 +#define STM32_UART_USART3_IRQ_PRIORITY 12 +#define STM32_UART_USART1_DMA_PRIORITY 0 +#define STM32_UART_USART2_DMA_PRIORITY 0 +#define STM32_UART_USART3_DMA_PRIORITY 0 +#define STM32_UART_DMA_ERROR_HOOK(uartp) osalSysHalt("DMA failure") + +/* + * USB driver system settings. + */ +#define STM32_USB_USE_USB1 TRUE +#define STM32_USB_LOW_POWER_ON_SUSPEND FALSE +#define STM32_USB_USB1_HP_IRQ_PRIORITY 13 +#define STM32_USB_USB1_LP_IRQ_PRIORITY 14 + +/* + * WDG driver system settings. + */ +#define STM32_WDG_USE_IWDG FALSE + +#endif /* MCUCONF_H */ diff --git a/keyboards/handwired/co60/rev6/rev6.c b/keyboards/handwired/co60/rev6/rev6.c new file mode 100644 index 000000000..f597513b1 --- /dev/null +++ b/keyboards/handwired/co60/rev6/rev6.c @@ -0,0 +1,39 @@ +/* Copyright 2019 John M Daly <jmdaly@gmail.com> + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ +#include "rev6.h" + +#include "backlight.h" +#include "led.h" +#include "printf.h" + +backlight_levels_config_t kb_backlight_config = { + .enable = true, + .breathing = true, + .level = BACKLIGHT_LEVELS +}; + +uint8_t *o_fb; + +uint16_t counterst = 0; + +void matrix_init_kb(void) { + matrix_init_user(); + backlight_init_ports(); +} + +void matrix_scan_kb(void) { + matrix_scan_user(); +} diff --git a/keyboards/handwired/co60/rev6/rev6.h b/keyboards/handwired/co60/rev6/rev6.h new file mode 100644 index 000000000..7d11f19d3 --- /dev/null +++ b/keyboards/handwired/co60/rev6/rev6.h @@ -0,0 +1,146 @@ +/* Copyright 2019 John M Daly <jmdaly@gmail.com> + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ +#pragma once + +#include "quantum.h" + +// This a shortcut to help you visually see your layout. +// The following is a layout that uses all available switch positions. +// The first section contains all of the arguments +// The second converts the arguments into a two-dimensional array +#define LAYOUT_all( \ + K000, K001, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011, K012, K013, K014, \ + K100, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111, K112, K113, K114, \ + K200, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211, K212, K213, K214, \ + K300, K301, K302, K303, K304, K305, K306, K307, K308, K309, K310, K311, K313, K314, \ + K400, K401, K402, K404, K406, K408, K410, K411, K412, K413, K414 \ +) \ +{ \ + { K000, K001, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011, K012, K013, K014 }, \ + { K100, KC_NO, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111, K112, K113, K114 }, \ + { K200, KC_NO, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211, K212, K213, K214 }, \ + { K300, K301, K302, K303, K304, K305, K306, K307, K308, K309, K310, K311, KC_NO, K313, K314 }, \ + { K400, K401, K402, KC_NO, K404, KC_NO, K406, KC_NO, K408, KC_NO, K410, K411, K412, K413, K414 }, \ +} + +#define LAYOUT_60_ansi( \ + K000, K001, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011, K012, K014, \ + K100, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111, K112, K113, K114, \ + K200, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211, K212, K214, \ + K300, K302, K303, K304, K305, K306, K307, K308, K309, K310, K311, K313, \ + K400, K401, K402, K406, K410, K411, K413, K414 \ +) \ +{ \ + { K000, K001, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011, K012, KC_NO, K014 }, \ + { K100, KC_NO, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111, K112, K113, K114 }, \ + { K200, KC_NO, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211, K212, KC_NO, K214 }, \ + { K300, KC_NO, K302, K303, K304, K305, K306, K307, K308, K309, K310, K311, KC_NO, K313, KC_NO }, \ + { K400, K401, K402, KC_NO, KC_NO, KC_NO, K406, KC_NO, KC_NO, KC_NO, K410, K411, KC_NO, K413, K414 }, \ +} + +#define LAYOUT_60_ansi_split_bs_rshift( \ + K000, K001, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011, K012, K013, K014, \ + K100, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111, K112, K113, K114, \ + K200, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211, K212, K214, \ + K300, K302, K303, K304, K305, K306, K307, K308, K309, K310, K311, K313, K314, \ + K400, K401, K402, K406, K410, K411, K413, K414 \ +) \ +{ \ + { K000, K001, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011, K012, K013, K014 }, \ + { K100, KC_NO, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111, K112, K113, K114 }, \ + { K200, KC_NO, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211, K212, KC_NO, K214 }, \ + { K300, KC_NO, K302, K303, K304, K305, K306, K307, K308, K309, K310, K311, KC_NO, K313, K314 }, \ + { K400, K401, K402, KC_NO, KC_NO, KC_NO, K406, KC_NO, KC_NO, KC_NO, K410, K411, KC_NO, K413, K414 }, \ +} + +#define LAYOUT_60_iso( \ + K000, K001, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011, K012, K014, \ + K100, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111, K112, K113, \ + K200, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211, K212, K213, K214, \ + K300, K301, K302, K303, K304, K305, K306, K307, K308, K309, K310, K311, K313, \ + K400, K401, K402, K406, K410, K411, K413, K414 \ +) \ +{ \ + { K000, K001, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011, K012, KC_NO, K014 }, \ + { K100, KC_NO, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111, K112, K113, KC_NO }, \ + { K200, KC_NO, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211, K212, K213, K214 }, \ + { K300, K301, K302, K303, K304, K305, K306, K307, K308, K309, K310, K311, KC_NO, K313, KC_NO }, \ + { K400, K401, K402, KC_NO, KC_NO, KC_NO, K406, KC_NO, KC_NO, KC_NO, K410, K411, KC_NO, K413, K414 }, \ +} + +#define LAYOUT_60_hhkb( \ + K000, K001, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011, K012, K013, K014, \ + K100, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111, K112, K113, K114, \ + K200, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211, K212, K214, \ + K300, K302, K303, K304, K305, K306, K307, K308, K309, K310, K311, K313, K314, \ + K401, K402, K406, K411, K413 \ +) \ +{ \ + { K000, K001, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011, K012, K013, K014 }, \ + { K100, KC_NO, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111, K112, K113, K114 }, \ + { K200, KC_NO, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211, K212, KC_NO, K214 }, \ + { K300, KC_NO, K302, K303, K304, K305, K306, K307, K308, K309, K310, K311, KC_NO, K313, K314 }, \ + { KC_NO, K401, K402, KC_NO, KC_NO, KC_NO, K406, KC_NO, KC_NO, KC_NO, KC_NO, K411, KC_NO, K413, KC_NO }, \ +} + +#define LAYOUT_60_hhkb_split_space( \ + K000, K001, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011, K012, K013, K014, \ + K100, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111, K112, K113, K114, \ + K200, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211, K212, K214, \ + K300, K302, K303, K304, K305, K306, K307, K308, K309, K310, K311, K313, K314, \ + K401, K402, K404, K406, K408, K411, K413 \ +) \ +{ \ + { K000, K001, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011, K012, K013, K014 }, \ + { K100, KC_NO, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111, K112, K113, K114 }, \ + { K200, KC_NO, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211, K212, KC_NO, K214 }, \ + { K300, KC_NO, K302, K303, K304, K305, K306, K307, K308, K309, K310, K311, KC_NO, K313, K314 }, \ + { KC_NO, K401, K402, KC_NO, K404, KC_NO, K406, KC_NO, K408, KC_NO, KC_NO, K411, KC_NO, K413, KC_NO }, \ +} + +#define LAYOUT_60_hhkb_split_625u_space( \ + K000, K001, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011, K012, K013, K014, \ + K100, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111, K112, K113, K114, \ + K200, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211, K212, K214, \ + K300, K302, K303, K304, K305, K306, K307, K308, K309, K310, K311, K313, K314, \ + K401, K402, K404, K406, K408, K410, K411, K413 \ +) \ +{ \ + { K000, K001, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011, K012, K013, K014 }, \ + { K100, KC_NO, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111, K112, K113, K114 }, \ + { K200, KC_NO, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211, K212, KC_NO, K214 }, \ + { K300, KC_NO, K302, K303, K304, K305, K306, K307, K308, K309, K310, K311, KC_NO, K313, K314 }, \ + { KC_NO, K401, K402, KC_NO, K404, KC_NO, K406, KC_NO, K408, KC_NO, K410, K411, KC_NO, K413, KC_NO }, \ +} + +// Backlighting +typedef union { + uint8_t raw; + struct { + bool enable :1; + bool breathing : 1; + uint8_t level :6; + }; +} backlight_levels_config_t; + +extern backlight_levels_config_t kb_backlight_config; +extern bool kb_backlight_breathing; + +void backlight_init_ports(void); +void backlight_set(uint8_t level); +bool is_breathing(void); +void breathing_enable(void); +void breathing_disable(void); diff --git a/keyboards/handwired/co60/rev6/rules.mk b/keyboards/handwired/co60/rev6/rules.mk new file mode 100644 index 000000000..dba41e12b --- /dev/null +++ b/keyboards/handwired/co60/rev6/rules.mk @@ -0,0 +1,59 @@ +# project specific files + +## chip/board settings +# - the next two should match the directories in +# <chibios>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES) +MCU_FAMILY = STM32 +MCU_SERIES = STM32F3xx + +# Linker script to use +# - it should exist either in <chibios>/os/common/ports/ARMCMx/compilers/GCC/ld/ +# or <this_dir>/ld/ +MCU_LDSCRIPT = STM32F303xC + +# Startup code to use +# - it should exist in <chibios>/os/common/startup/ARMCMx/compilers/GCC/mk/ +MCU_STARTUP = stm32f3xx + +# Board: it should exist either in <chibios>/os/hal/boards/ +# or <this_dir>/boards +BOARD = GENERIC_STM32_F303XC + +# Cortex version +MCU = cortex-m4 + +# ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7 +ARMV = 7 + +USE_FPU = yes + +# Vector table for application +# 0x00000000-0x00001000 area is occupied by bootlaoder.*/ +# The CORTEX_VTOR... is needed only for MCHCK/Infinity KB +# OPT_DEFS = -DCORTEX_VTOR_INIT=0x08005000 + +# Options to pass to dfu-util when flashing +DFU_ARGS = -d 0483:df11 -a 0 -s 0x08000000:leave +DFU_SUFFIX_ARGS = -v 0483 -p df11 + +# Code for backlight breathing: +SRC += led.c + +# Build Options +# comment out to disable the options. +# +BACKLIGHT_ENABLE = yes +BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE = yes # Mouse keys(+4700) +EXTRAKEY_ENABLE = yes # Audio control and System control(+450) +CONSOLE_ENABLE = no # Console for debug(+400) +COMMAND_ENABLE = no # Commands for debug and configuration +NKRO_ENABLE = yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +AUDIO_ENABLE = no +RGBLIGHT_ENABLE = no # Enable keyboard underlight functionality +MIDI_ENABLE = no # MIDI controls +UNICODE_ENABLE = no # Unicode +BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID +LEADER_ENABLE = yes + +LAYOUTS += 60_ansi 60_ansi_split_bs_rshift 60_iso 60_hhkb diff --git a/keyboards/handwired/co60/rev7/chconf.h b/keyboards/handwired/co60/rev7/chconf.h new file mode 100644 index 000000000..1d9f12ff1 --- /dev/null +++ b/keyboards/handwired/co60/rev7/chconf.h @@ -0,0 +1,520 @@ +/* + ChibiOS - Copyright (C) 2006..2016 Giovanni Di Sirio + + Licensed under the Apache License, Version 2.0 (the "License"); + you may not use this file except in compliance with the License. + You may obtain a copy of the License at + + http://www.apache.org/licenses/LICENSE-2.0 + + Unless required by applicable law or agreed to in writing, software + distributed under the License is distributed on an "AS IS" BASIS, + WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. + See the License for the specific language governing permissions and + limitations under the License. +*/ + +/** + * @file templates/chconf.h + * @brief Configuration file template. + * @details A copy of this file must be placed in each project directory, it + * contains the application specific kernel settings. + * + * @addtogroup config + * @details Kernel related settings and hooks. + * @{ + */ + +#ifndef CHCONF_H +#define CHCONF_H + +#define _CHIBIOS_RT_CONF_ + +/*===========================================================================*/ +/** + * @name System timers settings + * @{ + */ +/*===========================================================================*/ + +/** + * @brief System time counter resolution. + * @note Allowed values are 16 or 32 bits. + */ +#define CH_CFG_ST_RESOLUTION 32 + +/** + * @brief System tick frequency. + * @details Frequency of the system timer that drives the system ticks. This + * setting also defines the system tick time unit. + */ +#define CH_CFG_ST_FREQUENCY 100000 + +/** + * @brief Time delta constant for the tick-less mode. + * @note If this value is zero then the system uses the classic + * periodic tick. This value represents the minimum number + * of ticks that is safe to specify in a timeout directive. + * The value one is not valid, timeouts are rounded up to + * this value. + */ +#define CH_CFG_ST_TIMEDELTA 2 + +/** @} */ + +/*===========================================================================*/ +/** + * @name Kernel parameters and options + * @{ + */ +/*===========================================================================*/ + +/** + * @brief Round robin interval. + * @details This constant is the number of system ticks allowed for the + * threads before preemption occurs. Setting this value to zero + * disables the preemption for threads with equal priority and the + * round robin becomes cooperative. Note that higher priority + * threads can still preempt, the kernel is always preemptive. + * @note Disabling the round robin preemption makes the kernel more compact + * and generally faster. + * @note The round robin preemption is not supported in tickless mode and + * must be set to zero in that case. + */ +#define CH_CFG_TIME_QUANTUM 0 + +/** + * @brief Managed RAM size. + * @details Size of the RAM area to be managed by the OS. If set to zero + * then the whole available RAM is used. The core memory is made + * available to the heap allocator and/or can be used directly through + * the simplified core memory allocator. + * + * @note In order to let the OS manage the whole RAM the linker script must + * provide the @p __heap_base__ and @p __heap_end__ symbols. + * @note Requires @p CH_CFG_USE_MEMCORE. + */ +#define CH_CFG_MEMCORE_SIZE 0 + +/** + * @brief Idle thread automatic spawn suppression. + * @details When this option is activated the function @p chSysInit() + * does not spawn the idle thread. The application @p main() + * function becomes the idle thread and must implement an + * infinite loop. + */ +#define CH_CFG_NO_IDLE_THREAD FALSE + +/** @} */ + +/*===========================================================================*/ +/** + * @name Performance options + * @{ + */ +/*===========================================================================*/ + +/** + * @brief OS optimization. + * @details If enabled then time efficient rather than space efficient code + * is used when two possible implementations exist. + * + * @note This is not related to the compiler optimization options. + * @note The default is @p TRUE. + */ +#define CH_CFG_OPTIMIZE_SPEED TRUE + +/** @} */ + +/*===========================================================================*/ +/** + * @name Subsystem options + * @{ + */ +/*===========================================================================*/ + +/** + * @brief Time Measurement APIs. + * @details If enabled then the time measurement APIs are included in + * the kernel. + * + * @note The default is @p TRUE. + */ +#define CH_CFG_USE_TM TRUE + +/** + * @brief Threads registry APIs. + * @details If enabled then the registry APIs are included in the kernel. + * + * @note The default is @p TRUE. + */ +#define CH_CFG_USE_REGISTRY TRUE + +/** + * @brief Threads synchronization APIs. + * @details If enabled then the @p chThdWait() function is included in + * the kernel. + * + * @note The default is @p TRUE. + */ +#define CH_CFG_USE_WAITEXIT TRUE + +/** + * @brief Semaphores APIs. + * @details If enabled then the Semaphores APIs are included in the kernel. + * + * @note The default is @p TRUE. + */ +#define CH_CFG_USE_SEMAPHORES TRUE + +/** + * @brief Semaphores queuing mode. + * @details If enabled then the threads are enqueued on semaphores by + * priority rather than in FIFO order. + * + * @note The default is @p FALSE. Enable this if you have special + * requirements. + * @note Requires @p CH_CFG_USE_SEMAPHORES. + */ +#define CH_CFG_USE_SEMAPHORES_PRIORITY FALSE + +/** + * @brief Mutexes APIs. + * @details If enabled then the mutexes APIs are included in the kernel. + * + * @note The default is @p TRUE. + */ +#define CH_CFG_USE_MUTEXES TRUE + +/** + * @brief Enables recursive behavior on mutexes. + * @note Recursive mutexes are heavier and have an increased + * memory footprint. + * + * @note The default is @p FALSE. + * @note Requires @p CH_CFG_USE_MUTEXES. + */ +#define CH_CFG_USE_MUTEXES_RECURSIVE FALSE + +/** + * @brief Conditional Variables APIs. + * @details If enabled then the conditional variables APIs are included + * in the kernel. + * + * @note The default is @p TRUE. + * @note Requires @p CH_CFG_USE_MUTEXES. + */ +#define CH_CFG_USE_CONDVARS TRUE + +/** + * @brief Conditional Variables APIs with timeout. + * @details If enabled then the conditional variables APIs with timeout + * specification are included in the kernel. + * + * @note The default is @p TRUE. + * @note Requires @p CH_CFG_USE_CONDVARS. + */ +#define CH_CFG_USE_CONDVARS_TIMEOUT TRUE + +/** + * @brief Events Flags APIs. + * @details If enabled then the event flags APIs are included in the kernel. + * + * @note The default is @p TRUE. + */ +#define CH_CFG_USE_EVENTS TRUE + +/** + * @brief Events Flags APIs with timeout. + * @details If enabled then the events APIs with timeout specification + * are included in the kernel. + * + * @note The default is @p TRUE. + * @note Requires @p CH_CFG_USE_EVENTS. + */ +#define CH_CFG_USE_EVENTS_TIMEOUT TRUE + +/** + * @brief Synchronous Messages APIs. + * @details If enabled then the synchronous messages APIs are included + * in the kernel. + * + * @note The default is @p TRUE. + */ +#define CH_CFG_USE_MESSAGES TRUE + +/** + * @brief Synchronous Messages queuing mode. + * @details If enabled then messages are served by priority rather than in + * FIFO order. + * + * @note The default is @p FALSE. Enable this if you have special + * requirements. + * @note Requires @p CH_CFG_USE_MESSAGES. + */ +#define CH_CFG_USE_MESSAGES_PRIORITY TRUE + +/** + * @brief Mailboxes APIs. + * @details If enabled then the asynchronous messages (mailboxes) APIs are + * included in the kernel. + * + * @note The default is @p TRUE. + * @note Requires @p CH_CFG_USE_SEMAPHORES. + */ +#define CH_CFG_USE_MAILBOXES TRUE + +/** + * @brief Core Memory Manager APIs. + * @details If enabled then the core memory manager APIs are included + * in the kernel. + * + * @note The default is @p TRUE. + */ +#define CH_CFG_USE_MEMCORE TRUE + +/** + * @brief Heap Allocator APIs. + * @details If enabled then the memory heap allocator APIs are included + * in the kernel. + * + * @note The default is @p TRUE. + * @note Requires @p CH_CFG_USE_MEMCORE and either @p CH_CFG_USE_MUTEXES or + * @p CH_CFG_USE_SEMAPHORES. + * @note Mutexes are recommended. + */ +#define CH_CFG_USE_HEAP TRUE + +/** + * @brief Memory Pools Allocator APIs. + * @details If enabled then the memory pools allocator APIs are included + * in the kernel. + * + * @note The default is @p TRUE. + */ +#define CH_CFG_USE_MEMPOOLS TRUE + +/** + * @brief Dynamic Threads APIs. + * @details If enabled then the dynamic threads creation APIs are included + * in the kernel. + * + * @note The default is @p TRUE. + * @note Requires @p CH_CFG_USE_WAITEXIT. + * @note Requires @p CH_CFG_USE_HEAP and/or @p CH_CFG_USE_MEMPOOLS. + */ +#define CH_CFG_USE_DYNAMIC TRUE + +/** @} */ + +/*===========================================================================*/ +/** + * @name Debug options + * @{ + */ +/*===========================================================================*/ + +/** + * @brief Debug option, kernel statistics. + * + * @note The default is @p FALSE. + */ +#define CH_DBG_STATISTICS FALSE + +/** + * @brief Debug option, system state check. + * @details If enabled the correct call protocol for system APIs is checked + * at runtime. + * + * @note The default is @p FALSE. + */ +#define CH_DBG_SYSTEM_STATE_CHECK FALSE + +/** + * @brief Debug option, parameters checks. + * @details If enabled then the checks on the API functions input + * parameters are activated. + * + * @note The default is @p FALSE. + */ +#define CH_DBG_ENABLE_CHECKS FALSE + +/** + * @brief Debug option, consistency checks. + * @details If enabled then all the assertions in the kernel code are + * activated. This includes consistency checks inside the kernel, + * runtime anomalies and port-defined checks. + * + * @note The default is @p FALSE. + */ +#define CH_DBG_ENABLE_ASSERTS FALSE + +/** + * @brief Debug option, trace buffer. + * @details If enabled then the trace buffer is activated. + * + * @note The default is @p CH_DBG_TRACE_MASK_DISABLED. + */ +#define CH_DBG_TRACE_MASK CH_DBG_TRACE_MASK_DISABLED + +/** + * @brief Trace buffer entries. + * @note The trace buffer is only allocated if @p CH_DBG_TRACE_MASK is + * different from @p CH_DBG_TRACE_MASK_DISABLED. + */ +#define CH_DBG_TRACE_BUFFER_SIZE 128 + +/** + * @brief Debug option, stack checks. + * @details If enabled then a runtime stack check is performed. + * + * @note The default is @p FALSE. + * @note The stack check is performed in a architecture/port dependent way. + * It may not be implemented or some ports. + * @note The default failure mode is to halt the system with the global + * @p panic_msg variable set to @p NULL. + */ +#define CH_DBG_ENABLE_STACK_CHECK TRUE + +/** + * @brief Debug option, stacks initialization. + * @details If enabled then the threads working area is filled with a byte + * value when a thread is created. This can be useful for the + * runtime measurement of the used stack. + * + * @note The default is @p FALSE. + */ +#define CH_DBG_FILL_THREADS FALSE + +/** + * @brief Debug option, threads profiling. + * @details If enabled then a field is added to the @p thread_t structure that + * counts the system ticks occurred while executing the thread. + * + * @note The default is @p FALSE. + * @note This debug option is not currently compatible with the + * tickless mode. + */ +#define CH_DBG_THREADS_PROFILING FALSE + +/** @} */ + +/*===========================================================================*/ +/** + * @name Kernel hooks + * @{ + */ +/*===========================================================================*/ + +/** + * @brief Threads descriptor structure extension. + * @details User fields added to the end of the @p thread_t structure. + */ +#define CH_CFG_THREAD_EXTRA_FIELDS \ + /* Add threads custom fields here.*/ + +/** + * @brief Threads initialization hook. + * @details User initialization code added to the @p chThdInit() API. + * + * @note It is invoked from within @p chThdInit() and implicitly from all + * the threads creation APIs. + */ +#define CH_CFG_THREAD_INIT_HOOK(tp) { \ + /* Add threads initialization code here.*/ \ +} + +/** + * @brief Threads finalization hook. + * @details User finalization code added to the @p chThdExit() API. + */ +#define CH_CFG_THREAD_EXIT_HOOK(tp) { \ + /* Add threads finalization code here.*/ \ +} + +/** + * @brief Context switch hook. + * @details This hook is invoked just before switching between threads. + */ +#define CH_CFG_CONTEXT_SWITCH_HOOK(ntp, otp) { \ + /* Context switch code here.*/ \ +} + +/** + * @brief ISR enter hook. + */ +#define CH_CFG_IRQ_PROLOGUE_HOOK() { \ + /* IRQ prologue code here.*/ \ +} + +/** + * @brief ISR exit hook. + */ +#define CH_CFG_IRQ_EPILOGUE_HOOK() { \ + /* IRQ epilogue code here.*/ \ +} + +/** + * @brief Idle thread enter hook. + * @note This hook is invoked within a critical zone, no OS functions + * should be invoked from here. + * @note This macro can be used to activate a power saving mode. + */ +#define CH_CFG_IDLE_ENTER_HOOK() { \ + /* Idle-enter code here.*/ \ +} + +/** + * @brief Idle thread leave hook. + * @note This hook is invoked within a critical zone, no OS functions + * should be invoked from here. + * @note This macro can be used to deactivate a power saving mode. + */ +#define CH_CFG_IDLE_LEAVE_HOOK() { \ + /* Idle-leave code here.*/ \ +} + +/** + * @brief Idle Loop hook. + * @details This hook is continuously invoked by the idle thread loop. + */ +#define CH_CFG_IDLE_LOOP_HOOK() { \ + /* Idle loop code here.*/ \ +} + +/** + * @brief System tick event hook. + * @details This hook is invoked in the system tick handler immediately + * after processing the virtual timers queue. + */ +#define CH_CFG_SYSTEM_TICK_HOOK() { \ + /* System tick event code here.*/ \ +} + +/** + * @brief System halt hook. + * @details This hook is invoked in case to a system halting error before + * the system is halted. + */ +#define CH_CFG_SYSTEM_HALT_HOOK(reason) { \ + /* System halt code here.*/ \ +} + +/** + * @brief Trace hook. + * @details This hook is invoked each time a new record is written in the + * trace buffer. + */ +#define CH_CFG_TRACE_HOOK(tep) { \ + /* Trace code here.*/ \ +} + +/** @} */ + +/*===========================================================================*/ +/* Port-specific settings (override port settings defaulted in chcore.h). */ +/*===========================================================================*/ + +#endif /* CHCONF_H */ + +/** @} */ diff --git a/keyboards/handwired/co60/rev7/config.h b/keyboards/handwired/co60/rev7/config.h new file mode 100644 index 000000000..1ccc12ad4 --- /dev/null +++ b/keyboards/handwired/co60/rev7/config.h @@ -0,0 +1,70 @@ +/* +Copyright 2019 John M Daly <jmdaly@gmail.com> + +This program is free software: you can redistribute it and/or modify +it under the terms of the GNU General Public License as published by +the Free Software Foundation, either version 2 of the License, or +(at your option) any later version. + +This program is distributed in the hope that it will be useful, +but WITHOUT ANY WARRANTY; without even the implied warranty of +MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +GNU General Public License for more details. + +You should have received a copy of the GNU General Public License +along with this program. If not, see <http://www.gnu.org/licenses/>. +*/ + +#pragma once + +#include "config_common.h" + +/* USB Device descriptor parameter */ +#define VENDOR_ID 0xFEED +#define PRODUCT_ID 0x0000 +#define DEVICE_VER 0x0001 +#define MANUFACTURER John M Daly +#define PRODUCT CO60 rev7 +#define DESCRIPTION An open hardware sixty percent PCB + +/* Address for jumping to bootloader on STM32 chips. */ +/* It is chip dependent, the correct number can be looked up here: + * http://www.st.com/web/en/resource/technical/document/application_note/CD00167594.pdf + */ +#define STM32_BOOTLOADER_ADDRESS 0x1FFFD800 + +/* key matrix size */ +#define MATRIX_ROWS 5 +#define MATRIX_COLS 15 + +/* ROWS: Top to bottom, COLS: Left to right +*/ +#define MATRIX_ROW_PINS { A8, A2, B13, B2, B10 } +#define MATRIX_COL_PINS { A10, A9, A3, A4, A5, A6, B0, B1, A15, B3, B4, B5, C13, C14, C15 } +#define UNUSED_PINS + +/* COL2ROW, ROW2COL, or CUSTOM_MATRIX */ +#define DIODE_DIRECTION COL2ROW + +/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */ +#define DEBOUNCE 5 + +/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ +#define LOCKING_SUPPORT_ENABLE +/* Locking resynchronize hack */ +#define LOCKING_RESYNC_ENABLE + +/* Backlight configuration + * Backlight LEDs on B8 + */ +#define BACKLIGHT_LEVELS 24 +#define BACKLIGHT_BREATHING +#define BREATHING_PERIOD 6 + +#define RGBLIGHT_ANIMATIONS + +#define RGBLED_NUM 16 +#define RGB_DI_PIN A7 +#define DRIVER_LED_TOTAL RGBLED_NUM + +#define RGB_MATRIX_KEYPRESSES diff --git a/keyboards/handwired/co60/rev7/halconf.h b/keyboards/handwired/co60/rev7/halconf.h new file mode 100644 index 000000000..5e5d70219 --- /dev/null +++ b/keyboards/handwired/co60/rev7/halconf.h @@ -0,0 +1,388 @@ +/* + ChibiOS - Copyright (C) 2006..2016 Giovanni Di Sirio + + Licensed under the Apache License, Version 2.0 (the "License"); + you may not use this file except in compliance with the License. + You may obtain a copy of the License at + + http://www.apache.org/licenses/LICENSE-2.0 + + Unless required by applicable law or agreed to in writing, software + distributed under the License is distributed on an "AS IS" BASIS, + WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. + See the License for the specific language governing permissions and + limitations under the License. +*/ + +/** + * @file templates/halconf.h + * @brief HAL configuration header. + * @details HAL configuration file, this file allows to enable or disable the + * various device drivers from your application. You may also use + * this file in order to override the device drivers default settings. + * + * @addtogroup HAL_CONF + * @{ + */ + +#ifndef HALCONF_H +#define HALCONF_H + +#include "mcuconf.h" + +/** + * @brief Enables the PAL subsystem. + */ +#if !defined(HAL_USE_PAL) || defined(__DOXYGEN__) +#define HAL_USE_PAL TRUE +#endif + +/** + * @brief Enables the ADC subsystem. + */ +#if !defined(HAL_USE_ADC) || defined(__DOXYGEN__) +#define HAL_USE_ADC FALSE +#endif + +/** + * @brief Enables the CAN subsystem. + */ +#if !defined(HAL_USE_CAN) || defined(__DOXYGEN__) +#define HAL_USE_CAN FALSE +#endif + +/** + * @brief Enables the DAC subsystem. + */ +#if !defined(HAL_USE_DAC) || defined(__DOXYGEN__) +#define HAL_USE_DAC TRUE +#endif + +/** + * @brief Enables the EXT subsystem. + */ +#if !defined(HAL_USE_EXT) || defined(__DOXYGEN__) +#define HAL_USE_EXT FALSE +#endif + +/** + * @brief Enables the GPT subsystem. + */ +#if !defined(HAL_USE_GPT) || defined(__DOXYGEN__) +#define HAL_USE_GPT TRUE +#endif + +/** + * @brief Enables the I2C subsystem. + */ +#if !defined(HAL_USE_I2C) || defined(__DOXYGEN__) +#define HAL_USE_I2C FALSE +#endif + +/** + * @brief Enables the I2S subsystem. + */ +#if !defined(HAL_USE_I2S) || defined(__DOXYGEN__) +#define HAL_USE_I2S FALSE +#endif + +/** + * @brief Enables the ICU subsystem. + */ +#if !defined(HAL_USE_ICU) || defined(__DOXYGEN__) +#define HAL_USE_ICU FALSE +#endif + +/** + * @brief Enables the MAC subsystem. + */ +#if !defined(HAL_USE_MAC) || defined(__DOXYGEN__) +#define HAL_USE_MAC FALSE +#endif + +/** + * @brief Enables the MMC_SPI subsystem. + */ +#if !defined(HAL_USE_MMC_SPI) || defined(__DOXYGEN__) +#define HAL_USE_MMC_SPI FALSE +#endif + +/** + * @brief Enables the PWM subsystem. + */ +#if !defined(HAL_USE_PWM) || defined(__DOXYGEN__) +#define HAL_USE_PWM TRUE +#endif + +/** + * @brief Enables the QSPI subsystem. + */ +#if !defined(HAL_USE_QSPI) || defined(__DOXYGEN__) +#define HAL_USE_QSPI FALSE +#endif + +/** + * @brief Enables the RTC subsystem. + */ +#if !defined(HAL_USE_RTC) || defined(__DOXYGEN__) +#define HAL_USE_RTC FALSE +#endif + +/** + * @brief Enables the SDC subsystem. + */ +#if !defined(HAL_USE_SDC) || defined(__DOXYGEN__) +#define HAL_USE_SDC FALSE +#endif + +/** + * @brief Enables the SERIAL subsystem. + */ +#if !defined(HAL_USE_SERIAL) || defined(__DOXYGEN__) +#define HAL_USE_SERIAL FALSE +#endif + +/** + * @brief Enables the SERIAL over USB subsystem. + */ +#if !defined(HAL_USE_SERIAL_USB) || defined(__DOXYGEN__) +#define HAL_USE_SERIAL_USB TRUE +#endif + +/** + * @brief Enables the SPI subsystem. + */ +#if !defined(HAL_USE_SPI) || defined(__DOXYGEN__) +#define HAL_USE_SPI FALSE +#endif + +/** + * @brief Enables the UART subsystem. + */ +#if !defined(HAL_USE_UART) || defined(__DOXYGEN__) +#define HAL_USE_UART FALSE +#endif + +/** + * @brief Enables the USB subsystem. + */ +#if !defined(HAL_USE_USB) || defined(__DOXYGEN__) +#define HAL_USE_USB TRUE +#endif + +/** + * @brief Enables the WDG subsystem. + */ +#if !defined(HAL_USE_WDG) || defined(__DOXYGEN__) +#define HAL_USE_WDG FALSE +#endif + +/*===========================================================================*/ +/* ADC driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Enables synchronous APIs. + * @note Disabling this option saves both code and data space. + */ +#if !defined(ADC_USE_WAIT) || defined(__DOXYGEN__) +#define ADC_USE_WAIT TRUE +#endif + +/** + * @brief Enables the @p adcAcquireBus() and @p adcReleaseBus() APIs. + * @note Disabling this option saves both code and data space. + */ +#if !defined(ADC_USE_MUTUAL_EXCLUSION) || defined(__DOXYGEN__) +#define ADC_USE_MUTUAL_EXCLUSION TRUE +#endif + +/*===========================================================================*/ +/* CAN driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Sleep mode related APIs inclusion switch. + */ +#if !defined(CAN_USE_SLEEP_MODE) || defined(__DOXYGEN__) +#define CAN_USE_SLEEP_MODE TRUE +#endif + +/*===========================================================================*/ +/* I2C driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Enables the mutual exclusion APIs on the I2C bus. + */ +#if !defined(I2C_USE_MUTUAL_EXCLUSION) || defined(__DOXYGEN__) +#define I2C_USE_MUTUAL_EXCLUSION TRUE +#endif + +/*===========================================================================*/ +/* MAC driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Enables an event sources for incoming packets. + */ +#if !defined(MAC_USE_ZERO_COPY) || defined(__DOXYGEN__) +#define MAC_USE_ZERO_COPY FALSE +#endif + +/** + * @brief Enables an event sources for incoming packets. + */ +#if !defined(MAC_USE_EVENTS) || defined(__DOXYGEN__) +#define MAC_USE_EVENTS TRUE +#endif + +/*===========================================================================*/ +/* MMC_SPI driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Delays insertions. + * @details If enabled this options inserts delays into the MMC waiting + * routines releasing some extra CPU time for the threads with + * lower priority, this may slow down the driver a bit however. + * This option is recommended also if the SPI driver does not + * use a DMA channel and heavily loads the CPU. + */ +#if !defined(MMC_NICE_WAITING) || defined(__DOXYGEN__) +#define MMC_NICE_WAITING TRUE +#endif + +/*===========================================================================*/ +/* SDC driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Number of initialization attempts before rejecting the card. + * @note Attempts are performed at 10mS intervals. + */ +#if !defined(SDC_INIT_RETRY) || defined(__DOXYGEN__) +#define SDC_INIT_RETRY 100 +#endif + +/** + * @brief Include support for MMC cards. + * @note MMC support is not yet implemented so this option must be kept + * at @p FALSE. + */ +#if !defined(SDC_MMC_SUPPORT) || defined(__DOXYGEN__) +#define SDC_MMC_SUPPORT FALSE +#endif + +/** + * @brief Delays insertions. + * @details If enabled this options inserts delays into the MMC waiting + * routines releasing some extra CPU time for the threads with + * lower priority, this may slow down the driver a bit however. + */ +#if !defined(SDC_NICE_WAITING) || defined(__DOXYGEN__) +#define SDC_NICE_WAITING TRUE +#endif + +/*===========================================================================*/ +/* SERIAL driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Default bit rate. + * @details Configuration parameter, this is the baud rate selected for the + * default configuration. + */ +#if !defined(SERIAL_DEFAULT_BITRATE) || defined(__DOXYGEN__) +#define SERIAL_DEFAULT_BITRATE 38400 +#endif + +/** + * @brief Serial buffers size. + * @details Configuration parameter, you can change the depth of the queue + * buffers depending on the requirements of your application. + * @note The default is 16 bytes for both the transmission and receive + * buffers. + */ +#if !defined(SERIAL_BUFFERS_SIZE) || defined(__DOXYGEN__) +#define SERIAL_BUFFERS_SIZE 16 +#endif + +/*===========================================================================*/ +/* SERIAL_USB driver related setting. */ +/*===========================================================================*/ + +/** + * @brief Serial over USB buffers size. + * @details Configuration parameter, the buffer size must be a multiple of + * the USB data endpoint maximum packet size. + * @note The default is 256 bytes for both the transmission and receive + * buffers. + */ +#if !defined(SERIAL_USB_BUFFERS_SIZE) || defined(__DOXYGEN__) +#define SERIAL_USB_BUFFERS_SIZE 1 +#endif + +/** + * @brief Serial over USB number of buffers. + * @note The default is 2 buffers. + */ +#if !defined(SERIAL_USB_BUFFERS_NUMBER) || defined(__DOXYGEN__) +#define SERIAL_USB_BUFFERS_NUMBER 2 +#endif + +/*===========================================================================*/ +/* SPI driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Enables synchronous APIs. + * @note Disabling this option saves both code and data space. + */ +#if !defined(SPI_USE_WAIT) || defined(__DOXYGEN__) +#define SPI_USE_WAIT TRUE +#endif + +/** + * @brief Enables the @p spiAcquireBus() and @p spiReleaseBus() APIs. + * @note Disabling this option saves both code and data space. + */ +#if !defined(SPI_USE_MUTUAL_EXCLUSION) || defined(__DOXYGEN__) +#define SPI_USE_MUTUAL_EXCLUSION TRUE +#endif + +/*===========================================================================*/ +/* UART driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Enables synchronous APIs. + * @note Disabling this option saves both code and data space. + */ +#if !defined(UART_USE_WAIT) || defined(__DOXYGEN__) +#define UART_USE_WAIT FALSE +#endif + +/** + * @brief Enables the @p uartAcquireBus() and @p uartReleaseBus() APIs. + * @note Disabling this option saves both code and data space. + */ +#if !defined(UART_USE_MUTUAL_EXCLUSION) || defined(__DOXYGEN__) +#define UART_USE_MUTUAL_EXCLUSION FALSE +#endif + +/*===========================================================================*/ +/* USB driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Enables synchronous APIs. + * @note Disabling this option saves both code and data space. + */ +#if !defined(USB_USE_WAIT) || defined(__DOXYGEN__) +#define USB_USE_WAIT TRUE +#endif + +#endif /* HALCONF_H */ + +/** @} */ diff --git a/keyboards/handwired/co60/rev7/led.c b/keyboards/handwired/co60/rev7/led.c new file mode 100644 index 000000000..13f8d9860 --- /dev/null +++ b/keyboards/handwired/co60/rev7/led.c @@ -0,0 +1,242 @@ +/* +Copyright 2012 Jun Wako <wakojun@gmail.com> + +This program is free software: you can redistribute it and/or modify +it under the terms of the GNU General Public License as published by +the Free Software Foundation, either version 2 of the License, or +(at your option) any later version. + +This program is distributed in the hope that it will be useful, +but WITHOUT ANY WARRANTY; without even the implied warranty of +MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +GNU General Public License for more details. + +You should have received a copy of the GNU General Public License +along with this program. If not, see <http://www.gnu.org/licenses/>. +*/ + +#include "hal.h" +#include "led_custom.h" +#include "rev7.h" +#include "printf.h" + +static void breathing_callback(PWMDriver *pwmp); + +static PWMConfig pwmCFG = { + 0xFFFF, /* PWM clock frequency */ + 256, /* PWM period (in ticks) 1S (1/10kHz=0.1mS 0.1ms*10000 ticks=1S) */ + NULL, /* No Callback */ + { + {PWM_OUTPUT_DISABLED, NULL}, + {PWM_OUTPUT_DISABLED, NULL}, + {PWM_OUTPUT_ACTIVE_HIGH, NULL}, /* Enable Channel 3 */ + {PWM_OUTPUT_DISABLED, NULL} + }, + 0, /* HW dependent part.*/ + 0 +}; + +static PWMConfig pwmCFG_breathing = { + 0xFFFF, /* 10kHz PWM clock frequency */ + 256, /* PWM period (in ticks) 1S (1/10kHz=0.1mS 0.1ms*10000 ticks=1S) */ + breathing_callback, /* Breathing Callback */ + { + {PWM_OUTPUT_DISABLED, NULL}, + {PWM_OUTPUT_DISABLED, NULL}, + {PWM_OUTPUT_ACTIVE_HIGH, NULL}, /* Enable Channel 3 */ + {PWM_OUTPUT_DISABLED, NULL} + }, + 0, /* HW dependent part.*/ + 0 +}; + +// See http://jared.geek.nz/2013/feb/linear-led-pwm +static uint16_t cie_lightness(uint16_t v) { + if (v <= 5243) // if below 8% of max + return v / 9; // same as dividing by 900% + else { + uint32_t y = (((uint32_t) v + 10486) << 8) / (10486 + 0xFFFFUL); // add 16% of max and compare + // to get a useful result with integer division, we shift left in the expression above + // and revert what we've done again after squaring. + y = y * y * y >> 8; + if (y > 0xFFFFUL) // prevent overflow + return 0xFFFFU; + else + return (uint16_t) y; + } +} + + +void backlight_init_ports(void) { + palSetPadMode(GPIOB, 8, PAL_MODE_ALTERNATE(2)); + pwmStart(&PWMD4, &pwmCFG); + if(kb_backlight_config.enable){ + if(kb_backlight_config.breathing){ + breathing_enable(); + } else{ + backlight_set(kb_backlight_config.level); + } + } else { + backlight_set(0); + } +} + +void backlight_set(uint8_t level) { + uint32_t duty = (uint32_t)(cie_lightness(0xFFFF * (uint32_t) level / BACKLIGHT_LEVELS)); + if (level == 0) { + // Turn backlight off + // Disable channel 3 on PWM4 + pwmDisableChannel(&PWMD4, 2); + } else { + // Turn backlight on + if(!is_breathing()){ + // Enable channel 3 on PWM4 + pwmEnableChannel(&PWMD4, 2, PWM_FRACTION_TO_WIDTH(&PWMD4,0xFFFF,duty)); + } + } +} + + +uint8_t backlight_tick = 0; + +void backlight_task(void) { +} + +#define BREATHING_NO_HALT 0 +#define BREATHING_HALT_OFF 1 +#define BREATHING_HALT_ON 2 +#define BREATHING_STEPS 128 + +static uint8_t breathing_period = BREATHING_PERIOD; +static uint8_t breathing_halt = BREATHING_NO_HALT; +static uint16_t breathing_counter = 0; + +bool is_breathing(void) { + return PWMD4.config == &pwmCFG_breathing; +} + +#define breathing_min() do {breathing_counter = 0;} while (0) +#define breathing_max() do {breathing_counter = breathing_period * 256 / 2;} while (0) + + +void breathing_interrupt_enable(void){ + pwmStop(&PWMD4); + pwmStart(&PWMD4, &pwmCFG_breathing); + chSysLockFromISR(); + pwmEnablePeriodicNotification(&PWMD4); + pwmEnableChannelI( + &PWMD4, + 2, + PWM_FRACTION_TO_WIDTH( + &PWMD4, + 0xFFFF, + 0xFFFF + ) + ); + chSysUnlockFromISR(); +} + +void breathing_interrupt_disable(void){ + pwmStop(&PWMD4); + pwmStart(&PWMD4, &pwmCFG); +} + +void breathing_enable(void) +{ + breathing_counter = 0; + breathing_halt = BREATHING_NO_HALT; + breathing_interrupt_enable(); +} + +void breathing_pulse(void) +{ + if (kb_backlight_config.level == 0) + breathing_min(); + else + breathing_max(); + breathing_halt = BREATHING_HALT_ON; + breathing_interrupt_enable(); +} + +void breathing_disable(void) +{ + breathing_interrupt_disable(); + // Restore backlight level + backlight_set(kb_backlight_config.level); +} + +void breathing_self_disable(void) +{ + if (kb_backlight_config.level == 0) + breathing_halt = BREATHING_HALT_OFF; + else + breathing_halt = BREATHING_HALT_ON; +} + +void breathing_toggle(void) { + if (is_breathing()){ + breathing_disable(); + } else { + breathing_enable(); + } +} + +void breathing_period_set(uint8_t value) +{ + if (!value) + value = 1; + breathing_period = value; +} + +void breathing_period_default(void) { + breathing_period_set(BREATHING_PERIOD); +} + +void breathing_period_inc(void) +{ + breathing_period_set(breathing_period+1); +} + +void breathing_period_dec(void) +{ + breathing_period_set(breathing_period-1); +} + +/* To generate breathing curve in python: + * from math import sin, pi; [int(sin(x/128.0*pi)**4*255) for x in range(128)] + */ +static const uint8_t breathing_table[BREATHING_STEPS] = {0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 1, 1, 2, 3, 4, 5, 6, 8, 10, 12, 15, 17, 20, 24, 28, 32, 36, 41, 46, 51, 57, 63, 70, 76, 83, 91, 98, 106, 113, 121, 129, 138, 146, 154, 162, 170, 178, 185, 193, 200, 207, 213, 220, 225, 231, 235, 240, 244, 247, 250, 252, 253, 254, 255, 254, 253, 252, 250, 247, 244, 240, 235, 231, 225, 220, 213, 207, 200, 193, 185, 178, 170, 162, 154, 146, 138, 129, 121, 113, 106, 98, 91, 83, 76, 70, 63, 57, 51, 46, 41, 36, 32, 28, 24, 20, 17, 15, 12, 10, 8, 6, 5, 4, 3, 2, 1, 1, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0}; + +// Use this before the cie_lightness function. +static inline uint16_t scale_backlight(uint16_t v) { + return v / BACKLIGHT_LEVELS * kb_backlight_config.level; +} + +static void breathing_callback(PWMDriver *pwmp) +{ + (void)pwmp; + uint16_t interval = (uint16_t) breathing_period * 256 / BREATHING_STEPS; + // resetting after one period to prevent ugly reset at overflow. + breathing_counter = (breathing_counter + 1) % (breathing_period * 256); + uint8_t index = breathing_counter / interval % BREATHING_STEPS; + + if (((breathing_halt == BREATHING_HALT_ON) && (index == BREATHING_STEPS / 2)) || + ((breathing_halt == BREATHING_HALT_OFF) && (index == BREATHING_STEPS - 1))) + { + breathing_interrupt_disable(); + } + + uint32_t duty = cie_lightness(scale_backlight(breathing_table[index] * 256)); + + chSysLockFromISR(); + pwmEnableChannelI( + &PWMD4, + 2, + PWM_FRACTION_TO_WIDTH( + &PWMD4, + 0xFFFF, + duty + ) + ); + chSysUnlockFromISR(); +} diff --git a/keyboards/handwired/co60/rev7/led_custom.h b/keyboards/handwired/co60/rev7/led_custom.h new file mode 100644 index 000000000..56e723db8 --- /dev/null +++ b/keyboards/handwired/co60/rev7/led_custom.h @@ -0,0 +1,22 @@ +/* +Copyright 2019 John M Daly <jmdaly@gmail.com> + +This program is free software: you can redistribute it and/or modify +it under the terms of the GNU General Public License as published by +the Free Software Foundation, either version 2 of the License, or +(at your option) any later version. + +This program is distributed in the hope that it will be useful, +but WITHOUT ANY WARRANTY; without even the implied warranty of +MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +GNU General Public License for more details. + +You should have received a copy of the GNU General Public License +along with this program. If not, see <http://www.gnu.org/licenses/>. +*/ + +#pragma once + +void backlight_task(void); +void breathing_interrupt_disable(void); +void breathing_interrupt_enable(void); diff --git a/keyboards/handwired/co60/rev7/mcuconf.h b/keyboards/handwired/co60/rev7/mcuconf.h new file mode 100644 index 000000000..69bf9185d --- /dev/null +++ b/keyboards/handwired/co60/rev7/mcuconf.h @@ -0,0 +1,257 @@ +/* + ChibiOS - Copyright (C) 2006..2016 Giovanni Di Sirio + + Licensed under the Apache License, Version 2.0 (the "License"); + you may not use this file except in compliance with the License. + You may obtain a copy of the License at + + http://www.apache.org/licenses/LICENSE-2.0 + + Unless required by applicable law or agreed to in writing, software + distributed under the License is distributed on an "AS IS" BASIS, + WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. + See the License for the specific language governing permissions and + limitations under the License. +*/ + +#ifndef MCUCONF_H +#define MCUCONF_H + +/* + * STM32F3xx drivers configuration. + * The following settings override the default settings present in + * the various device driver implementation headers. + * Note that the settings for each driver only have effect if the whole + * driver is enabled in halconf.h. + * + * IRQ priorities: + * 15...0 Lowest...Highest. + * + * DMA priorities: + * 0...3 Lowest...Highest. + */ + +#define STM32F3xx_MCUCONF + +/* + * HAL driver system settings. + */ +#define STM32_NO_INIT FALSE +#define STM32_PVD_ENABLE FALSE +#define STM32_PLS STM32_PLS_LEV0 +#define STM32_HSI_ENABLED TRUE +#define STM32_LSI_ENABLED TRUE +#define STM32_HSE_ENABLED TRUE +#define STM32_LSE_ENABLED FALSE +#define STM32_SW STM32_SW_PLL +#define STM32_PLLSRC STM32_PLLSRC_HSE +#define STM32_PREDIV_VALUE 1 +#define STM32_PLLMUL_VALUE 9 +#define STM32_HPRE STM32_HPRE_DIV1 +#define STM32_PPRE1 STM32_PPRE1_DIV2 +#define STM32_PPRE2 STM32_PPRE2_DIV2 +#define STM32_MCOSEL STM32_MCOSEL_NOCLOCK +#define STM32_ADC12PRES STM32_ADC12PRES_DIV1 +#define STM32_ADC34PRES STM32_ADC34PRES_DIV1 +#define STM32_USART1SW STM32_USART1SW_PCLK +#define STM32_USART2SW STM32_USART2SW_PCLK +#define STM32_USART3SW STM32_USART3SW_PCLK +#define STM32_UART4SW STM32_UART4SW_PCLK +#define STM32_UART5SW STM32_UART5SW_PCLK +#define STM32_I2C1SW STM32_I2C1SW_SYSCLK +#define STM32_I2C2SW STM32_I2C2SW_SYSCLK +#define STM32_TIM1SW STM32_TIM1SW_PCLK2 +#define STM32_TIM8SW STM32_TIM8SW_PCLK2 +#define STM32_RTCSEL STM32_RTCSEL_LSI +#define STM32_USB_CLOCK_REQUIRED TRUE +#define STM32_USBPRE STM32_USBPRE_DIV1P5 + +#undef STM32_HSE_BYPASS +// #error "oh no" +// #endif + +/* + * ADC driver system settings. + */ +#define STM32_ADC_DUAL_MODE FALSE +#define STM32_ADC_COMPACT_SAMPLES FALSE +#define STM32_ADC_USE_ADC1 FALSE +#define STM32_ADC_USE_ADC2 FALSE +#define STM32_ADC_USE_ADC3 FALSE +#define STM32_ADC_USE_ADC4 FALSE +#define STM32_ADC_ADC1_DMA_STREAM STM32_DMA_STREAM_ID(1, 1) +#define STM32_ADC_ADC2_DMA_STREAM STM32_DMA_STREAM_ID(2, 1) +#define STM32_ADC_ADC3_DMA_STREAM STM32_DMA_STREAM_ID(2, 5) +#define STM32_ADC_ADC4_DMA_STREAM STM32_DMA_STREAM_ID(2, 2) +#define STM32_ADC_ADC1_DMA_PRIORITY 2 +#define STM32_ADC_ADC2_DMA_PRIORITY 2 +#define STM32_ADC_ADC3_DMA_PRIORITY 2 +#define STM32_ADC_ADC4_DMA_PRIORITY 2 +#define STM32_ADC_ADC12_IRQ_PRIORITY 5 +#define STM32_ADC_ADC3_IRQ_PRIORITY 5 +#define STM32_ADC_ADC4_IRQ_PRIORITY 5 +#define STM32_ADC_ADC1_DMA_IRQ_PRIORITY 5 +#define STM32_ADC_ADC2_DMA_IRQ_PRIORITY 5 +#define STM32_ADC_ADC3_DMA_IRQ_PRIORITY 5 +#define STM32_ADC_ADC4_DMA_IRQ_PRIORITY 5 +#define STM32_ADC_ADC12_CLOCK_MODE ADC_CCR_CKMODE_AHB_DIV1 +#define STM32_ADC_ADC34_CLOCK_MODE ADC_CCR_CKMODE_AHB_DIV1 + +/* + * CAN driver system settings. + */ +#define STM32_CAN_USE_CAN1 FALSE +#define STM32_CAN_CAN1_IRQ_PRIORITY 11 + +/* + * DAC driver system settings. + */ +#define STM32_DAC_DUAL_MODE FALSE +#define STM32_DAC_USE_DAC1_CH1 TRUE +#define STM32_DAC_USE_DAC1_CH2 TRUE +#define STM32_DAC_DAC1_CH1_IRQ_PRIORITY 10 +#define STM32_DAC_DAC1_CH2_IRQ_PRIORITY 10 +#define STM32_DAC_DAC1_CH1_DMA_PRIORITY 2 +#define STM32_DAC_DAC1_CH2_DMA_PRIORITY 2 + +/* + * EXT driver system settings. + */ +#define STM32_EXT_EXTI0_IRQ_PRIORITY 6 +#define STM32_EXT_EXTI1_IRQ_PRIORITY 6 +#define STM32_EXT_EXTI2_IRQ_PRIORITY 6 +#define STM32_EXT_EXTI3_IRQ_PRIORITY 6 +#define STM32_EXT_EXTI4_IRQ_PRIORITY 6 +#define STM32_EXT_EXTI5_9_IRQ_PRIORITY 6 +#define STM32_EXT_EXTI10_15_IRQ_PRIORITY 6 +#define STM32_EXT_EXTI16_IRQ_PRIORITY 6 +#define STM32_EXT_EXTI17_IRQ_PRIORITY 6 +#define STM32_EXT_EXTI18_IRQ_PRIORITY 6 +#define STM32_EXT_EXTI19_IRQ_PRIORITY 6 +#define STM32_EXT_EXTI20_IRQ_PRIORITY 6 +#define STM32_EXT_EXTI21_22_29_IRQ_PRIORITY 6 +#define STM32_EXT_EXTI30_32_IRQ_PRIORITY 6 +#define STM32_EXT_EXTI33_IRQ_PRIORITY 6 + +/* + * GPT driver system settings. + */ +#define STM32_GPT_USE_TIM1 FALSE +#define STM32_GPT_USE_TIM2 FALSE +#define STM32_GPT_USE_TIM3 FALSE +#define STM32_GPT_USE_TIM4 FALSE +#define STM32_GPT_USE_TIM6 TRUE +#define STM32_GPT_USE_TIM7 TRUE +#define STM32_GPT_USE_TIM8 TRUE +#define STM32_GPT_TIM1_IRQ_PRIORITY 7 +#define STM32_GPT_TIM2_IRQ_PRIORITY 7 +#define STM32_GPT_TIM3_IRQ_PRIORITY 7 +#define STM32_GPT_TIM4_IRQ_PRIORITY 7 +#define STM32_GPT_TIM6_IRQ_PRIORITY 7 +#define STM32_GPT_TIM7_IRQ_PRIORITY 7 +#define STM32_GPT_TIM8_IRQ_PRIORITY 7 + +/* + * I2C driver system settings. + */ +#define STM32_I2C_USE_I2C1 FALSE +#define STM32_I2C_USE_I2C2 FALSE +#define STM32_I2C_BUSY_TIMEOUT 50 +#define STM32_I2C_I2C1_IRQ_PRIORITY 10 +#define STM32_I2C_I2C2_IRQ_PRIORITY 10 +#define STM32_I2C_USE_DMA TRUE +#define STM32_I2C_I2C1_DMA_PRIORITY 1 +#define STM32_I2C_I2C2_DMA_PRIORITY 1 +#define STM32_I2C_DMA_ERROR_HOOK(i2cp) osalSysHalt("DMA failure") + +/* + * ICU driver system settings. + */ +#define STM32_ICU_USE_TIM1 FALSE +#define STM32_ICU_USE_TIM2 FALSE +#define STM32_ICU_USE_TIM3 FALSE +#define STM32_ICU_USE_TIM4 FALSE +#define STM32_ICU_USE_TIM8 FALSE +#define STM32_ICU_TIM1_IRQ_PRIORITY 7 +#define STM32_ICU_TIM2_IRQ_PRIORITY 7 +#define STM32_ICU_TIM3_IRQ_PRIORITY 7 +#define STM32_ICU_TIM4_IRQ_PRIORITY 7 +#define STM32_ICU_TIM8_IRQ_PRIORITY 7 + +/* + * PWM driver system settings. + */ +#define STM32_PWM_USE_ADVANCED FALSE +#define STM32_PWM_USE_TIM1 FALSE +#define STM32_PWM_USE_TIM2 FALSE +#define STM32_PWM_USE_TIM3 FALSE +#define STM32_PWM_USE_TIM4 TRUE +#define STM32_PWM_USE_TIM8 FALSE +#define STM32_PWM_TIM1_IRQ_PRIORITY 7 +#define STM32_PWM_TIM2_IRQ_PRIORITY 7 +#define STM32_PWM_TIM3_IRQ_PRIORITY 7 +#define STM32_PWM_TIM4_IRQ_PRIORITY 7 +#define STM32_PWM_TIM8_IRQ_PRIORITY 7 + +/* + * SERIAL driver system settings. + */ +#define STM32_SERIAL_USE_USART1 FALSE +#define STM32_SERIAL_USE_USART2 TRUE +#define STM32_SERIAL_USE_USART3 FALSE +#define STM32_SERIAL_USE_UART4 FALSE +#define STM32_SERIAL_USE_UART5 FALSE +#define STM32_SERIAL_USART1_PRIORITY 12 +#define STM32_SERIAL_USART2_PRIORITY 12 +#define STM32_SERIAL_USART3_PRIORITY 12 +#define STM32_SERIAL_UART4_PRIORITY 12 +#define STM32_SERIAL_UART5_PRIORITY 12 + +/* + * SPI driver system settings. + */ +#define STM32_SPI_USE_SPI1 FALSE +#define STM32_SPI_USE_SPI2 FALSE +#define STM32_SPI_USE_SPI3 FALSE +#define STM32_SPI_SPI1_DMA_PRIORITY 1 +#define STM32_SPI_SPI2_DMA_PRIORITY 1 +#define STM32_SPI_SPI3_DMA_PRIORITY 1 +#define STM32_SPI_SPI1_IRQ_PRIORITY 10 +#define STM32_SPI_SPI2_IRQ_PRIORITY 10 +#define STM32_SPI_SPI3_IRQ_PRIORITY 10 +#define STM32_SPI_DMA_ERROR_HOOK(spip) osalSysHalt("DMA failure") + +/* + * ST driver system settings. + */ +#define STM32_ST_IRQ_PRIORITY 8 +#define STM32_ST_USE_TIMER 2 + +/* + * UART driver system settings. + */ +#define STM32_UART_USE_USART1 FALSE +#define STM32_UART_USE_USART2 FALSE +#define STM32_UART_USE_USART3 FALSE +#define STM32_UART_USART1_IRQ_PRIORITY 12 +#define STM32_UART_USART2_IRQ_PRIORITY 12 +#define STM32_UART_USART3_IRQ_PRIORITY 12 +#define STM32_UART_USART1_DMA_PRIORITY 0 +#define STM32_UART_USART2_DMA_PRIORITY 0 +#define STM32_UART_USART3_DMA_PRIORITY 0 +#define STM32_UART_DMA_ERROR_HOOK(uartp) osalSysHalt("DMA failure") + +/* + * USB driver system settings. + */ +#define STM32_USB_USE_USB1 TRUE +#define STM32_USB_LOW_POWER_ON_SUSPEND FALSE +#define STM32_USB_USB1_HP_IRQ_PRIORITY 13 +#define STM32_USB_USB1_LP_IRQ_PRIORITY 14 + +/* + * WDG driver system settings. + */ +#define STM32_WDG_USE_IWDG FALSE + +#endif /* MCUCONF_H */ diff --git a/keyboards/handwired/co60/rev7/rev7.c b/keyboards/handwired/co60/rev7/rev7.c new file mode 100644 index 000000000..3d0964d89 --- /dev/null +++ b/keyboards/handwired/co60/rev7/rev7.c @@ -0,0 +1,39 @@ +/* Copyright 2019 John M Daly <jmdaly@gmail.com> + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ +#include "rev7.h" + +#include "backlight.h" +#include "led.h" +#include "printf.h" + +backlight_levels_config_t kb_backlight_config = { + .enable = true, + .breathing = true, + .level = BACKLIGHT_LEVELS +}; + +uint8_t *o_fb; + +uint16_t counterst = 0; + +void matrix_init_kb(void) { + matrix_init_user(); + backlight_init_ports(); +} + +void matrix_scan_kb(void) { + matrix_scan_user(); +} diff --git a/keyboards/handwired/co60/rev7/rev7.h b/keyboards/handwired/co60/rev7/rev7.h new file mode 100644 index 000000000..4ab2b8d72 --- /dev/null +++ b/keyboards/handwired/co60/rev7/rev7.h @@ -0,0 +1,146 @@ +/* Copyright 2019 Jack Humbert <jmdaly@gmail.com> + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ +#pragma once + +#include "quantum.h" + +// This a shortcut to help you visually see your layout. +// The following is a layout that uses all available switch positions. +// The first section contains all of the arguments +// The second converts the arguments into a two-dimensional array +#define LAYOUT_all( \ + K000, K001, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011, K012, K013, K014, \ + K100, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111, K112, K113, K114, \ + K200, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211, K212, K213, K214, \ + K300, K301, K302, K303, K304, K305, K306, K307, K308, K309, K310, K311, K313, K314, \ + K400, K401, K402, K404, K406, K408, K410, K411, K412, K413, K414 \ +) \ +{ \ + { K000, K001, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011, K012, K013, K014 }, \ + { K100, KC_NO, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111, K112, K113, K114 }, \ + { K200, KC_NO, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211, K212, K213, K214 }, \ + { K300, K301, K302, K303, K304, K305, K306, K307, K308, K309, K310, K311, KC_NO, K313, K314 }, \ + { K400, K401, K402, KC_NO, K404, KC_NO, K406, KC_NO, K408, KC_NO, K410, K411, K412, K413, K414 }, \ +} + +#define LAYOUT_60_ansi( \ + K000, K001, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011, K012, K014, \ + K100, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111, K112, K113, K114, \ + K200, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211, K212, K214, \ + K300, K302, K303, K304, K305, K306, K307, K308, K309, K310, K311, K313, \ + K400, K401, K402, K406, K410, K411, K413, K414 \ +) \ +{ \ + { K000, K001, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011, K012, KC_NO, K014 }, \ + { K100, KC_NO, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111, K112, K113, K114 }, \ + { K200, KC_NO, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211, K212, KC_NO, K214 }, \ + { K300, KC_NO, K302, K303, K304, K305, K306, K307, K308, K309, K310, K311, KC_NO, K313, KC_NO }, \ + { K400, K401, K402, KC_NO, KC_NO, KC_NO, K406, KC_NO, KC_NO, KC_NO, K410, K411, KC_NO, K413, K414 }, \ +} + +#define LAYOUT_60_ansi_split_bs_rshift( \ + K000, K001, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011, K012, K013, K014, \ + K100, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111, K112, K113, K114, \ + K200, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211, K212, K214, \ + K300, K302, K303, K304, K305, K306, K307, K308, K309, K310, K311, K313, K314, \ + K400, K401, K402, K406, K410, K411, K413, K414 \ +) \ +{ \ + { K000, K001, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011, K012, K013, K014 }, \ + { K100, KC_NO, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111, K112, K113, K114 }, \ + { K200, KC_NO, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211, K212, KC_NO, K214 }, \ + { K300, KC_NO, K302, K303, K304, K305, K306, K307, K308, K309, K310, K311, KC_NO, K313, K314 }, \ + { K400, K401, K402, KC_NO, KC_NO, KC_NO, K406, KC_NO, KC_NO, KC_NO, K410, K411, KC_NO, K413, K414 }, \ +} + +#define LAYOUT_60_iso( \ + K000, K001, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011, K012, K014, \ + K100, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111, K112, K113, \ + K200, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211, K212, K213, K214, \ + K300, K301, K302, K303, K304, K305, K306, K307, K308, K309, K310, K311, K313, \ + K400, K401, K402, K406, K410, K411, K413, K414 \ +) \ +{ \ + { K000, K001, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011, K012, KC_NO, K014 }, \ + { K100, KC_NO, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111, K112, K113, KC_NO }, \ + { K200, KC_NO, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211, K212, K213, K214 }, \ + { K300, K301, K302, K303, K304, K305, K306, K307, K308, K309, K310, K311, KC_NO, K313, KC_NO }, \ + { K400, K401, K402, KC_NO, KC_NO, KC_NO, K406, KC_NO, KC_NO, KC_NO, K410, K411, KC_NO, K413, K414 }, \ +} + +#define LAYOUT_60_hhkb( \ + K000, K001, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011, K012, K013, K014, \ + K100, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111, K112, K113, K114, \ + K200, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211, K212, K214, \ + K300, K302, K303, K304, K305, K306, K307, K308, K309, K310, K311, K313, K314, \ + K401, K402, K406, K411, K413 \ +) \ +{ \ + { K000, K001, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011, K012, K013, K014 }, \ + { K100, KC_NO, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111, K112, K113, K114 }, \ + { K200, KC_NO, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211, K212, KC_NO, K214 }, \ + { K300, KC_NO, K302, K303, K304, K305, K306, K307, K308, K309, K310, K311, KC_NO, K313, K314 }, \ + { KC_NO, K401, K402, KC_NO, KC_NO, KC_NO, K406, KC_NO, KC_NO, KC_NO, KC_NO, K411, KC_NO, K413, KC_NO }, \ +} + +#define LAYOUT_60_hhkb_split_space( \ + K000, K001, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011, K012, K013, K014, \ + K100, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111, K112, K113, K114, \ + K200, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211, K212, K214, \ + K300, K302, K303, K304, K305, K306, K307, K308, K309, K310, K311, K313, K314, \ + K401, K402, K404, K406, K408, K411, K413 \ +) \ +{ \ + { K000, K001, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011, K012, K013, K014 }, \ + { K100, KC_NO, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111, K112, K113, K114 }, \ + { K200, KC_NO, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211, K212, KC_NO, K214 }, \ + { K300, KC_NO, K302, K303, K304, K305, K306, K307, K308, K309, K310, K311, KC_NO, K313, K314 }, \ + { KC_NO, K401, K402, KC_NO, K404, KC_NO, K406, KC_NO, K408, KC_NO, KC_NO, K411, KC_NO, K413, KC_NO }, \ +} + +#define LAYOUT_60_hhkb_split_625u_space( \ + K000, K001, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011, K012, K013, K014, \ + K100, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111, K112, K113, K114, \ + K200, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211, K212, K214, \ + K300, K302, K303, K304, K305, K306, K307, K308, K309, K310, K311, K313, K314, \ + K401, K402, K404, K406, K408, K410, K411, K413 \ +) \ +{ \ + { K000, K001, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011, K012, K013, K014 }, \ + { K100, KC_NO, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111, K112, K113, K114 }, \ + { K200, KC_NO, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211, K212, KC_NO, K214 }, \ + { K300, KC_NO, K302, K303, K304, K305, K306, K307, K308, K309, K310, K311, KC_NO, K313, K314 }, \ + { KC_NO, K401, K402, KC_NO, K404, KC_NO, K406, KC_NO, K408, KC_NO, K410, K411, KC_NO, K413, KC_NO }, \ +} + +// Backlighting +typedef union { + uint8_t raw; + struct { + bool enable :1; + bool breathing : 1; + uint8_t level :6; + }; +} backlight_levels_config_t; + +extern backlight_levels_config_t kb_backlight_config; +extern bool kb_backlight_breathing; + +void backlight_init_ports(void); +void backlight_set(uint8_t level); +bool is_breathing(void); +void breathing_enable(void); +void breathing_disable(void); diff --git a/keyboards/handwired/co60/rev7/rules.mk b/keyboards/handwired/co60/rev7/rules.mk new file mode 100644 index 000000000..6e0b3856a --- /dev/null +++ b/keyboards/handwired/co60/rev7/rules.mk @@ -0,0 +1,59 @@ +# project specific files + +## chip/board settings +# - the next two should match the directories in +# <chibios>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES) +MCU_FAMILY = STM32 +MCU_SERIES = STM32F3xx + +# Linker script to use +# - it should exist either in <chibios>/os/common/ports/ARMCMx/compilers/GCC/ld/ +# or <this_dir>/ld/ +MCU_LDSCRIPT = STM32F303xC + +# Startup code to use +# - it should exist in <chibios>/os/common/startup/ARMCMx/compilers/GCC/mk/ +MCU_STARTUP = stm32f3xx + +# Board: it should exist either in <chibios>/os/hal/boards/ +# or <this_dir>/boards +BOARD = GENERIC_STM32_F303XC + +# Cortex version +MCU = cortex-m4 + +# ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7 +ARMV = 7 + +USE_FPU = yes + +# Vector table for application +# 0x00000000-0x00001000 area is occupied by bootlaoder.*/ +# The CORTEX_VTOR... is needed only for MCHCK/Infinity KB +# OPT_DEFS = -DCORTEX_VTOR_INIT=0x08005000 + +# Options to pass to dfu-util when flashing +DFU_ARGS = -d 0483:df11 -a 0 -s 0x08000000:leave +DFU_SUFFIX_ARGS = -v 0483 -p df11 + +# Code for backlight breathing: +SRC += led.c + +# Build Options +# comment out to disable the options. +# +BACKLIGHT_ENABLE = yes +BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE = yes # Mouse keys(+4700) +EXTRAKEY_ENABLE = yes # Audio control and System control(+450) +CONSOLE_ENABLE = no # Console for debug(+400) +COMMAND_ENABLE = no # Commands for debug and configuration +NKRO_ENABLE = yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +AUDIO_ENABLE = no +RGBLIGHT_ENABLE = no # Enable keyboard underlight functionality +MIDI_ENABLE = no # MIDI controls +UNICODE_ENABLE = no # Unicode +BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID +LEADER_ENABLE = yes + +LAYOUTS = 60_ansi 60_ansi_split_bs_rshift 60_iso 60_hhkb diff --git a/keyboards/handwired/dactyl/config.h b/keyboards/handwired/dactyl/config.h index 8d42c0ae4..49524c209 100644 --- a/keyboards/handwired/dactyl/config.h +++ b/keyboards/handwired/dactyl/config.h @@ -36,7 +36,8 @@ along with this program. If not, see <http://www.gnu.org/licenses/>. #define COL_EXPANDED { true, true, true, true, true, true, false, false, false, false, false, false} #define MATRIX_ONBOARD_ROW_PINS { F0, F1, F4, F5, F6, F7 } #define MATRIX_ONBOARD_COL_PINS { 0, 0, 0, 0, 0, 0, B1, B2, B3, D2, D3, C6 } -#define EXPANDER_COL_REGISTER 0 +#define EXPANDER_COL_REGISTER GPIOA +#define EXPANDER_ROW_REGISTER GPIOB #define MATRIX_EXPANDER_COL_PINS {0, 1, 2, 3, 4, 5} #define MATRIX_EXPANDER_ROW_PINS {0, 1, 2, 3, 4, 5} diff --git a/keyboards/handwired/dactyl/matrix.c b/keyboards/handwired/dactyl/matrix.c index f63cf1188..28cf37522 100644 --- a/keyboards/handwired/dactyl/matrix.c +++ b/keyboards/handwired/dactyl/matrix.c @@ -31,11 +31,11 @@ along with this program. If not, see <http://www.gnu.org/licenses/>. /* Set 0 if debouncing isn't needed */ -#ifndef DEBOUNCING_DELAY -# define DEBOUNCING_DELAY 5 +#ifndef DEBOUNCE +# define DEBOUNCE 5 #endif -#if (DEBOUNCING_DELAY > 0) +#if (DEBOUNCE > 0) static uint16_t debouncing_time; static bool debouncing = false; #endif @@ -82,10 +82,6 @@ uint32_t matrix_scan_count; #endif #define ROW_SHIFTER ((matrix_row_t)1) -#if (DIODE_DIRECTION == COL2ROW) -// bitmask to ensure the row state from the expander only applies to its columns -#define EXPANDER_MASK ((matrix_row_t)0b00111111) -#endif __attribute__ ((weak)) void matrix_init_user(void) {} @@ -166,17 +162,17 @@ void init_expander(void) { /* Pin direction and pull-up depends on both the diode direction - and on whether the column register is 0 ("A") or 1 ("B"): + and on whether the column register is GPIOA or GPIOB +-------+---------------+---------------+ | | ROW2COL | COL2ROW | +-------+---------------+---------------+ - | Reg 0 | input, output | output, input | + | GPIOA | input, output | output, input | +-------+---------------+---------------+ - | Reg 1 | output, input | input, output | + | GPIOB | output, input | input, output | +-------+---------------+---------------+ */ -#if (EXPANDER_COLUMN_REGISTER == 0) +#if (EXPANDER_COL_REGISTER == GPIOA) # if (DIODE_DIRECTION == COL2ROW) expander_status = i2c_write(expander_input_pin_mask); if (expander_status) goto out; expander_status = i2c_write(0); if (expander_status) goto out; @@ -184,7 +180,7 @@ void init_expander(void) { expander_status = i2c_write(0); if (expander_status) goto out; expander_status = i2c_write(expander_input_pin_mask); if (expander_status) goto out; # endif -#elif (EXPANDER_COLUMN_REGISTER == 1) +#elif (EXPANDER_COL_REGISTER == GPIOB) # if (DIODE_DIRECTION == COL2ROW) expander_status = i2c_write(0); if (expander_status) goto out; expander_status = i2c_write(expander_input_pin_mask); if (expander_status) goto out; @@ -202,7 +198,7 @@ void init_expander(void) { // - driving : off : 0 expander_status = i2c_start(I2C_ADDR_WRITE); if (expander_status) goto out; expander_status = i2c_write(GPPUA); if (expander_status) goto out; -#if (EXPANDER_COLUMN_REGISTER == 0) +#if (EXPANDER_COL_REGISTER == GPIOA) # if (DIODE_DIRECTION == COL2ROW) expander_status = i2c_write(expander_input_pin_mask); if (expander_status) goto out; expander_status = i2c_write(0); if (expander_status) goto out; @@ -210,7 +206,7 @@ void init_expander(void) { expander_status = i2c_write(0); if (expander_status) goto out; expander_status = i2c_write(expander_input_pin_mask); if (expander_status) goto out; # endif -#elif (EXPANDER_COLUMN_REGISTER == 1) +#elif (EXPANDER_COL_REGISTER == GPIOB) # if (DIODE_DIRECTION == COL2ROW) expander_status = i2c_write(0); if (expander_status) goto out; expander_status = i2c_write(expander_input_pin_mask); if (expander_status) goto out; @@ -256,7 +252,7 @@ uint8_t matrix_scan(void) #if (DIODE_DIRECTION == COL2ROW) for (uint8_t current_row = 0; current_row < MATRIX_ROWS; current_row++) { -# if (DEBOUNCING_DELAY > 0) +# if (DEBOUNCE > 0) bool matrix_changed = read_cols_on_row(matrix_debouncing, current_row); if (matrix_changed) { @@ -270,7 +266,7 @@ uint8_t matrix_scan(void) #elif (DIODE_DIRECTION == ROW2COL) for (uint8_t current_col = 0; current_col < MATRIX_COLS; current_col++) { -# if (DEBOUNCING_DELAY > 0) +# if (DEBOUNCE > 0) bool matrix_changed = read_rows_on_col(matrix_debouncing, current_col); if (matrix_changed) { @@ -284,8 +280,8 @@ uint8_t matrix_scan(void) } #endif -# if (DEBOUNCING_DELAY > 0) - if (debouncing && (timer_elapsed(debouncing_time) > DEBOUNCING_DELAY)) { +# if (DEBOUNCE > 0) + if (debouncing && (timer_elapsed(debouncing_time) > DEBOUNCE)) { for (uint8_t i = 0; i < MATRIX_ROWS; i++) { matrix[i] = matrix_debouncing[i]; } @@ -299,7 +295,7 @@ uint8_t matrix_scan(void) bool matrix_is_modified(void) // deprecated and evidently not called. { -#if (DEBOUNCING_DELAY > 0) +#if (DEBOUNCE > 0) if (debouncing) return false; #endif return true; @@ -365,11 +361,11 @@ static bool read_cols_on_row(matrix_row_t current_matrix[], uint8_t current_row) // Read columns from expander, unless it's in an error state if (! expander_status) { - expander_status = i2c_start(I2C_ADDR_WRITE); if (expander_status) goto out; - expander_status = i2c_write(GPIOA); if (expander_status) goto out; - expander_status = i2c_start(I2C_ADDR_READ); if (expander_status) goto out; + expander_status = i2c_start(I2C_ADDR_WRITE); if (expander_status) goto out; + expander_status = i2c_write(EXPANDER_COL_REGISTER); if (expander_status) goto out; + expander_status = i2c_start(I2C_ADDR_READ); if (expander_status) goto out; - current_matrix[current_row] |= (~i2c_readNak()) & EXPANDER_MASK; + current_matrix[current_row] |= (~i2c_readNak()) & expander_input_pin_mask; out: i2c_stop(); @@ -394,9 +390,9 @@ static void select_row(uint8_t row) { if (! expander_status) { // set active row low : 0 // set other rows hi-Z : 1 - expander_status = i2c_start(I2C_ADDR_WRITE); if (expander_status) goto out; - expander_status = i2c_write(GPIOB); if (expander_status) goto out; - expander_status = i2c_write(0xFF & ~(1<<row)); if (expander_status) goto out; + expander_status = i2c_start(I2C_ADDR_WRITE); if (expander_status) goto out; + expander_status = i2c_write(EXPANDER_ROW_REGISTER); if (expander_status) goto out; + expander_status = i2c_write(0xFF & ~(1<<row)); if (expander_status) goto out; out: i2c_stop(); } @@ -454,9 +450,9 @@ static bool read_rows_on_col(matrix_row_t current_matrix[], uint8_t current_col) return false; } - expander_status = i2c_start(I2C_ADDR_WRITE); if (expander_status) goto out; - expander_status = i2c_write(GPIOB); if (expander_status) goto out; - expander_status = i2c_start(I2C_ADDR_READ); if (expander_status) goto out; + expander_status = i2c_start(I2C_ADDR_WRITE); if (expander_status) goto out; + expander_status = i2c_write(EXPANDER_ROW_REGISTER); if (expander_status) goto out; + expander_status = i2c_start(I2C_ADDR_READ); if (expander_status) goto out; column_state = i2c_readNak(); out: @@ -504,9 +500,9 @@ static void select_col(uint8_t col) } else { // set active col low : 0 // set other cols hi-Z : 1 - expander_status = i2c_start(I2C_ADDR_WRITE); if (expander_status) goto out; - expander_status = i2c_write(GPIOA); if (expander_status) goto out; - expander_status = i2c_write(0xFF & ~(1<<col)); if (expander_status) goto out; + expander_status = i2c_start(I2C_ADDR_WRITE); if (expander_status) goto out; + expander_status = i2c_write(EXPANDER_COL_REGISTER); if (expander_status) goto out; + expander_status = i2c_write(0xFF & ~(1<<col)); if (expander_status) goto out; out: i2c_stop(); } diff --git a/keyboards/handwired/dactyl_manuform/4x5/config.h b/keyboards/handwired/dactyl_manuform/4x5/config.h index c8417a2f0..1f24c9aca 100644 --- a/keyboards/handwired/dactyl_manuform/4x5/config.h +++ b/keyboards/handwired/dactyl_manuform/4x5/config.h @@ -40,7 +40,9 @@ along with this program. If not, see <http://www.gnu.org/licenses/>. /* define if matrix has ghost */ //#define MATRIX_HAS_GHOST +// WS2812 RGB LED strip input and number of LEDs +#define RGB_DI_PIN D3 +#define RGBLED_NUM 12 + /* number of backlight levels */ // #define BACKLIGHT_LEVELS 3 - - diff --git a/keyboards/handwired/dactyl_manuform/4x6/config.h b/keyboards/handwired/dactyl_manuform/4x6/config.h index d4a192287..a9ad1a36d 100644 --- a/keyboards/handwired/dactyl_manuform/4x6/config.h +++ b/keyboards/handwired/dactyl_manuform/4x6/config.h @@ -38,3 +38,7 @@ along with this program. If not, see <http://www.gnu.org/licenses/>. /* COL2ROW or ROW2COL */ #define DIODE_DIRECTION COL2ROW + +// WS2812 RGB LED strip input and number of LEDs +#define RGB_DI_PIN D3 +#define RGBLED_NUM 12 diff --git a/keyboards/handwired/dactyl_manuform/5x6/config.h b/keyboards/handwired/dactyl_manuform/5x6/config.h index 06ac02dfc..413039449 100644 --- a/keyboards/handwired/dactyl_manuform/5x6/config.h +++ b/keyboards/handwired/dactyl_manuform/5x6/config.h @@ -32,10 +32,12 @@ along with this program. If not, see <http://www.gnu.org/licenses/>. #define MATRIX_COL_PINS { D4, C6, D7, E6, B4, B5 } #define MATRIX_ROW_PINS { F6, F7, B1, B3, B2, B6 } +// WS2812 RGB LED strip input and number of LEDs +#define RGB_DI_PIN D3 +#define RGBLED_NUM 12 /* define if matrix has ghost */ //#define MATRIX_HAS_GHOST /* number of backlight levels */ // #define BACKLIGHT_LEVELS 3 - diff --git a/keyboards/handwired/dactyl_manuform/5x6/keymaps/333fred/keymap.c b/keyboards/handwired/dactyl_manuform/5x6/keymaps/333fred/keymap.c index 4f6151a51..bc61579de 100644 --- a/keyboards/handwired/dactyl_manuform/5x6/keymaps/333fred/keymap.c +++ b/keyboards/handwired/dactyl_manuform/5x6/keymaps/333fred/keymap.c @@ -43,38 +43,18 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { ), [VIM] = LAYOUT_5x6( - _______, RESET, _______, _______, _______, _______, _______, _______, _______, _______, RESET, _______, - _______, _______, _______, _______, KC_LSFT, _______, _______, _______, _______, _______, _______, _______, - _______, M(DLEFT), M(DRIGHT), KC_LCTL, KC_LGUI, _______, KC_LEFT, KC_DOWN, KC_UP, KC_RGHT, _______, _______, - _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, - _______, _______, _______, _______, - _______, _______, _______, _______, - _______, _______, _______, _______, - _______, _______, _______, _______ + _______, RESET, _______, _______, _______, _______, _______, _______, _______, _______, RESET, _______, + _______, _______, _______, _______, KC_LSFT, _______, _______, _______, _______, _______, _______, _______, + _______, DLEFT, DRIGHT, KC_LCTL, KC_LGUI, _______, KC_LEFT, KC_DOWN, KC_UP, KC_RGHT, _______, _______, + _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, + _______, _______, _______, _______, + _______, _______, _______, _______, + _______, _______, _______, _______, + _______, _______, _______, _______ ), }; -const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt) { - switch(id) { - case DLEFT: - if (record->event.pressed) { // Windows move desktop left - return MACRO(D(LCTL), D(LGUI), T(LEFT), U(LGUI), U(LCTL), END); - } - break; - case DRIGHT: - if (record->event.pressed) { // Windows move desktop right - return MACRO(D(LCTL), D(LGUI), T(RIGHT), U(LGUI), U(LCTL), END); - } - break; - case PSCREEN_APP: if (record->event.pressed) { - return MACRO(D(LALT), T(PSCR), U(LALT), END); - } - break; - } - return MACRO_NONE; -} - bool process_record_user(uint16_t keycode, keyrecord_t *record) { - tap_dance_process_record(keycode); - return true; + tap_dance_process_keycode(keycode); + return !try_handle_macro(keycode, record); } diff --git a/keyboards/handwired/dactyl_manuform/5x7/config.h b/keyboards/handwired/dactyl_manuform/5x7/config.h index bef48f17e..435837498 100644 --- a/keyboards/handwired/dactyl_manuform/5x7/config.h +++ b/keyboards/handwired/dactyl_manuform/5x7/config.h @@ -31,3 +31,7 @@ along with this program. If not, see <http://www.gnu.org/licenses/>. // wiring of each half #define MATRIX_ROW_PINS { D4, C6, D7, E6, B4, B5 } #define MATRIX_COL_PINS { F5, F6, F7, B1, B3, B2, B6 } + +// WS2812 RGB LED strip input and number of LEDs +#define RGB_DI_PIN D3 +#define RGBLED_NUM 12 diff --git a/keyboards/handwired/dactyl_manuform/6x6/config.h b/keyboards/handwired/dactyl_manuform/6x6/config.h index 9bb7b07bf..9bc501c5e 100644 --- a/keyboards/handwired/dactyl_manuform/6x6/config.h +++ b/keyboards/handwired/dactyl_manuform/6x6/config.h @@ -31,3 +31,7 @@ along with this program. If not, see <http://www.gnu.org/licenses/>. // wiring of each half #define MATRIX_COL_PINS { D4, C6, D7, E6, B4, B5 } #define MATRIX_ROW_PINS { F5, F6, F7, B1, B3, B2, B6 } + +// WS2812 RGB LED strip input and number of LEDs +#define RGB_DI_PIN D3 +#define RGBLED_NUM 12 diff --git a/keyboards/handwired/dactyl_manuform/config.h b/keyboards/handwired/dactyl_manuform/config.h index 5e7605d3a..7c95f7058 100644 --- a/keyboards/handwired/dactyl_manuform/config.h +++ b/keyboards/handwired/dactyl_manuform/config.h @@ -36,7 +36,7 @@ along with this program. If not, see <http://www.gnu.org/licenses/>. #define MOUSEKEY_WHEEL_DELAY 0 /* Set 0 if debouncing isn't needed */ -#define DEBOUNCING_DELAY 5 +#define DEBOUNCE 5 /* serial.c configuration for split keyboard */ #define SOFT_SERIAL_PIN D0 @@ -49,11 +49,6 @@ along with this program. If not, see <http://www.gnu.org/licenses/>. /* Enables This makes it easier for fast typists to use dual-function keys */ #define PERMISSIVE_HOLD -/* ws2812 RGB LED */ -#define RGB_DI_PIN D3 - -#define RGBLED_NUM 12 // Number of LEDs - /* * Feature disable options * These options are also useful to firmware size reduction. diff --git a/keyboards/handwired/dactyl_manuform/dactyl_manuform.h b/keyboards/handwired/dactyl_manuform/dactyl_manuform.h index eea0757d5..72f2acaab 100644 --- a/keyboards/handwired/dactyl_manuform/dactyl_manuform.h +++ b/keyboards/handwired/dactyl_manuform/dactyl_manuform.h @@ -10,6 +10,8 @@ #include "5x7.h" #elif KEYBOARD_handwired_dactyl_manuform_6x6 #include "6x6.h" +#elif KEYBOARD_handwired_dactyl_manuform_dmote_62key + #include "62key.h" #endif //void promicro_bootloader_jmp(bool program); @@ -23,5 +25,3 @@ #include <avr/interrupt.h> #endif #endif - - diff --git a/keyboards/handwired/dactyl_manuform/dmote/62key/62key.c b/keyboards/handwired/dactyl_manuform/dmote/62key/62key.c new file mode 100644 index 000000000..e5d444277 --- /dev/null +++ b/keyboards/handwired/dactyl_manuform/dmote/62key/62key.c @@ -0,0 +1,5 @@ +#include "62key.h" + +void matrix_init_kb(void) { + matrix_init_user(); +}; diff --git a/keyboards/handwired/dactyl_manuform/dmote/62key/62key.h b/keyboards/handwired/dactyl_manuform/dmote/62key/62key.h new file mode 100644 index 000000000..273410165 --- /dev/null +++ b/keyboards/handwired/dactyl_manuform/dmote/62key/62key.h @@ -0,0 +1,54 @@ +#pragma once + +#include "dactyl_manuform.h" +#include "quantum.h" + +#ifdef USE_I2C +#include <stddef.h> +#ifdef __AVR__ + #include <avr/io.h> + #include <avr/interrupt.h> +#endif +#endif + +// This uses the same coordinate system as the program that defines +// the case model, but not the same coordinates. +// Numbers increase going to the right and away from the user on the +// right-hand side of the keyboard. This is mirrored for the +// left-hand side. +// The matrix is constructed for ease of soldering, with the columns +// of the thumb cluster extending along the sides of the finger +// cluster so that everything can be contained in a 6x6 pattern. + +#define LAYOUT_62key( \ + LA_20, LA_10, LF_35, LF_25, LF_15, LF_05, \ + LF_55, LF_45, LF_34, LF_24, LF_14, LF_04, \ + LF_54, LF_44, LF_33, LF_23, LF_13, LF_03, \ + LF_53, LF_43, LF_32, LF_22, LF_12, \ + LF_21, LT_21, LT_22, \ + LT_10, LT_11, LT_12, \ + LT_01, LT_02, \ + \ + RF_05, RF_15, RF_25, RF_35, RA_10, RA_20, \ + RF_04, RF_14, RF_24, RF_34, RF_45, RF_55, \ + RF_03, RF_13, RF_23, RF_33, RF_44, RF_54, \ + RF_12, RF_22, RF_32, RF_43, RF_53, \ + RT_22, RT_21, RF_21, \ + RT_12, RT_11, RT_10, \ + RT_02, RT_01 \ + ) \ + { \ + { LA_20, LA_10, LF_35, LF_25, LF_15, LF_05 }, \ + { LF_55, LF_45, LF_34, LF_24, LF_14, LF_04 }, \ + { LF_54, LF_44, LF_33, LF_23, LF_13, LF_03 }, \ + { LF_53, LF_43, LF_32, LF_22, LF_12, LT_22 }, \ + { KC_NO, KC_NO, LT_21, LF_21, LT_11, LT_12 }, \ + { KC_NO, KC_NO, LT_10, KC_NO, LT_01, LT_02 }, \ + \ + { RA_20, RA_10, RF_35, RF_25, RF_15, RF_05 }, \ + { RF_55, RF_45, RF_34, RF_24, RF_14, RF_04 }, \ + { RF_54, RF_44, RF_33, RF_23, RF_13, RF_03 }, \ + { RF_53, RF_43, RF_32, RF_22, RF_12, RT_22 }, \ + { KC_NO, KC_NO, RT_21, RF_21, RT_11, RT_12 }, \ + { KC_NO, KC_NO, RT_10, KC_NO, RT_01, RT_02 }, \ + } diff --git a/keyboards/handwired/dactyl_manuform/dmote/62key/config.h b/keyboards/handwired/dactyl_manuform/dmote/62key/config.h new file mode 100644 index 000000000..7db3ceb75 --- /dev/null +++ b/keyboards/handwired/dactyl_manuform/dmote/62key/config.h @@ -0,0 +1,49 @@ +#pragma once + +#include "config_common.h" + +#define PRODUCT DMOTE (62-key) +#define MATRIX_ROWS 12 +#define MATRIX_COLS 6 + +// MCUs are flipped on each side, relative to the shape of the case, +// but for ease of mounting, the pinout is not flipped with the controller. +// The same finger on each hand uses a column connected to the pin with the +// same silk-screen label on each Pro Micro. + +// Pin use: +// +// MCU | Silk | DMOTE +// -----+------+---------- +// D3 | TX0 | +// D2 | RX1 | +// D1 | 2 | LED strip input (dominant half only) +// D0 | 3 | Serial interface between halves +// D4 | 4 | Outermost pinky-finger column +// C6 | 5 | Column +// D7 | 6 | Column +// E6 | 7 | Column +// B4 | 8 | Column +// B5 | 9 | Outermost index-finger column +// -----+------+---------- +// F4 | A3 | +// F5 | A2 | +// F6 | A1 | Top row (furthest from user) +// F7 | A0 | Row +// B1 | 15 | Row +// B3 | 14 | Row +// B2 | 16 | Row +// B6 | 10 | Bottom row (closest to user) +#define MATRIX_ROW_PINS { F6, F7, B1, B3, B2, B6 } +#define MATRIX_COL_PINS { D4, C6, D7, E6, B4, B5 } + +// WS2812 RGB LED, normally used to indicate keyboard state: +#define RGBLIGHT_EFFECT_KNIGHT +#define RGBLIGHT_EFFECT_KNIGHT_LENGTH 2 +#define RGBLIGHT_EFFECT_CHRISTMAS +#define RGBLIGHT_EFFECT_CHRISTMAS_STEP 1 +#define RGB_DI_PIN D1 +#define RGBLED_NUM 6 // Used when chaining strips +#define RGBLED_SPLIT { 3, 3 } // Used when not chaining strips +#define ws2812_PORTREG PORTD +#define ws2812_DDRREG DDRD diff --git a/keyboards/handwired/dactyl_manuform/dmote/62key/keymaps/default/config.h b/keyboards/handwired/dactyl_manuform/dmote/62key/keymaps/default/config.h new file mode 100644 index 000000000..2e1d4f8dc --- /dev/null +++ b/keyboards/handwired/dactyl_manuform/dmote/62key/keymaps/default/config.h @@ -0,0 +1,5 @@ +#pragma once + +#define USE_SERIAL + +#define EE_HANDS diff --git a/keyboards/handwired/dactyl_manuform/dmote/62key/keymaps/default/keymap.c b/keyboards/handwired/dactyl_manuform/dmote/62key/keymaps/default/keymap.c new file mode 100644 index 000000000..3012d40a1 --- /dev/null +++ b/keyboards/handwired/dactyl_manuform/dmote/62key/keymaps/default/keymap.c @@ -0,0 +1,146 @@ +#include "62key.h" +#include "rgblight.h" +#include <keymap_colemak.h> +#include <sendstring_colemak.h> + +extern keymap_config_t keymap_config; + +// Automatic Layer ID: +enum layer_names { + _QWERTY, // OS-side Colemak. Default. + _COLEMAK, // Keyboard-side Colemak. Portability, emergency. + _NUMERIC +}; + +// Shorthand: +#define LAYER_N MO(_NUMERIC) +#define LAYER_C TG(_COLEMAK) +#define PASTE LSFT(KC_INS) // Terminal-compatible paste. +#define SLQ RALT(KC_9) // Single left-side quotation mark (in Colemak). +#define SRQ RALT(KC_0) +#define EMDASH RALT(LSFT(KC_MINUS)) // Em dash character (in Colemak). +#define BK_LCTL CTL_T(KC_LBRACKET) +#define BK_RCTL RCTL_T(KC_RBRACKET) +// TODO: Mod-tap ALT with a curvilinear brace. +// https://github.com/qmk/qmk_firmware/pull/2055 + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { + +[_QWERTY] = LAYOUT_62key( + KC_VOLD, KC_VOLU, CM_W, CM_F, CM_P, CM_G, + KC_TAB, CM_Q, CM_R, CM_S, CM_T, CM_D, + KC_BSPC, CM_A, CM_X, CM_C, CM_V, CM_B, + SLQ, CM_Z, KC_HOME, KC_PGUP, KC_END, + KC_PGDN, KC_ENT, KC_SPC, + KC_LSPO, KC_LGUI, KC_MINS, + BK_LCTL, KC_LALT, + + CM_J, CM_L, CM_U, CM_Y, KC_MPLY, KC_MUTE, + CM_H, CM_N, CM_E, CM_I, CM_SCLN, KC_BSLS, + CM_K, CM_M, KC_COMM, KC_DOT, CM_O, KC_QUOT, + KC_LEFT, KC_UP, KC_RGHT, KC_SLSH, SRQ, + KC_DEL, KC_ESC, KC_DOWN, + KC_EQL, LAYER_N, KC_RSPC, + KC_RALT, BK_RCTL +), + +[_COLEMAK] = LAYOUT_62key( + _______, _______, KC_W, KC_F, KC_P, KC_G, + _______, KC_Q, KC_R, KC_S, KC_T, KC_D, + _______, KC_A, KC_X, KC_C, KC_V, KC_B, + _______, KC_Z, _______, _______, _______, + _______, _______, _______, + _______, _______, _______, + _______, _______, + + KC_J, KC_L, KC_U, KC_Y, _______, _______, + KC_H, KC_N, KC_E, KC_I, KC_SCLN, _______, + KC_K, KC_M, _______, _______, KC_O, _______, + _______, _______, _______, _______, _______, + _______, _______, _______, + _______, _______, _______, + _______, _______ +), + +[_NUMERIC] = LAYOUT_62key( + LAYER_C, KC_INS, KC_F2, KC_F3, KC_F4, KC_F5, + KC_F12, KC_F1, KC_2, KC_3, KC_4, KC_5, + _______, KC_1, KC_AT, KC_HASH, KC_DLR, KC_PERC, + KC_GRV, KC_EXLM, KC_BTN1, KC_WH_U, KC_BTN2, + KC_WH_D, RGB_MOD, _______, + _______, _______, EMDASH, + _______, _______, + + KC_F6, KC_F7, KC_F8, KC_F9, RESET, KC_WAKE, // * + KC_6, KC_7, KC_8, KC_9, KC_F10, KC_F11, + KC_CIRC, KC_AMPR, KC_ASTR, KC_APP, KC_0, PASTE, + KC_MS_L, KC_MS_U, KC_MS_R, KC_PSCR, RGB_TOG, + KC_ACL1, KC_ACL2, KC_MS_D, + KC_ACL0, _______, _______, + _______, _______ +) +}; +// *KC_WAKE: Used in place of KC_SLEP because X11 with i3 on prerelease +// Debian 10 was seeing duplicate keypress and release events for sleep +// (regardless of i3 binding), which ruined the function. + + +/* +The rest is all about lighting control. +The logic here represents a pretty poor compromise solution between the +following concerns: + +- Feedback on active modifiers. +- Flexibility: Both sides of the keyboard are interchangeable. +- Regular QMK RBG lighting modes. Specifically, Knight and Xmas. + +Currently, the last item suffers, because the first two seem to require +calling a function that implements the RGBLIGHT_SPLIT_SET_CHANGE_HSVS macro, +which most of the rgblight.c functions do not. In particular, functions that +target an individual LED do not do so correctly across the wire, so instead +we let HSV vary without ever targeting LEDs. +*/ + +// How long to wait between animation steps for "Knight" animation: +const uint8_t RGBLED_KNIGHT_INTERVALS[] PROGMEM = {255, 200, 100}; + +bool _initialized = false; +bool _leds_dirty = false; + +void modal_leds(void) { + uint8_t mods = get_mods(); + uint16_t hue = 355; // Rough match to printed case. + uint8_t saturation = 255; + uint8_t value = 0; + if (layer_state_is(_COLEMAK)) { hue -= 50; saturation -= 20; value += 20; }; + if (layer_state_is(_NUMERIC)) { value += 30; }; + if (mods & MOD_MASK_SHIFT) { saturation -= 20; value += 30; }; + if (mods & MOD_MASK_ALT) { hue -= 100; saturation -= 20; value += 30; }; + if (mods & MOD_MASK_CTRL) { hue -= 200; saturation -= 20; value += 30; }; + // rgblight_sethsv_eeprom_helper is not a great API function but it does + // affect both halves of a split keyboard. + rgblight_sethsv_eeprom_helper(hue, saturation, value, false); + _leds_dirty = false; +} + +void matrix_init_user(void) { +} + +void matrix_scan_user(void) { + if (_leds_dirty) { modal_leds(); }; +} + +bool process_record_user(uint16_t keycode, keyrecord_t *record) { + if (!_initialized) { + // Static lighting is amenable to customization. + rgblight_mode(RGBLIGHT_MODE_STATIC_LIGHT); + _initialized = true; + }; + if (keycode == KC_WAKE) { + // Turn the lights off before going to sleep. + rgblight_sethsv_eeprom_helper(0, 0, 0, false); + } else { + _leds_dirty = true; + }; + return true; +} diff --git a/keyboards/handwired/dactyl_manuform/dmote/62key/rules.mk b/keyboards/handwired/dactyl_manuform/dmote/62key/rules.mk new file mode 100644 index 000000000..28d0bfb5c --- /dev/null +++ b/keyboards/handwired/dactyl_manuform/dmote/62key/rules.mk @@ -0,0 +1,5 @@ +# Build-process overrides for the DMOTE. +MOUSEKEY_ENABLE = yes # Mouse keys(+4700) +EXTRAKEY_ENABLE = yes # Audio control and System control(+450) +RGBLIGHT_ENABLE = yes # Needed for the C linker with lighting control. +COMMAND_ENABLE = no # Not a good combo with Space Cadet shift. diff --git a/keyboards/handwired/dactyl_manuform/dmote/config.h b/keyboards/handwired/dactyl_manuform/dmote/config.h new file mode 100644 index 000000000..b8c5759db --- /dev/null +++ b/keyboards/handwired/dactyl_manuform/dmote/config.h @@ -0,0 +1,3 @@ +#pragma once + +#include "config_common.h" diff --git a/keyboards/handwired/dactyl_manuform/dmote/readme.md b/keyboards/handwired/dactyl_manuform/dmote/readme.md new file mode 100644 index 000000000..7aff2df52 --- /dev/null +++ b/keyboards/handwired/dactyl_manuform/dmote/readme.md @@ -0,0 +1,16 @@ +DMOTE +====== + +The “Dactyl-ManuForm: Opposable Thumb Edition” is made from a Clojure +application maintained [here](https://github.com/veikman/dactyl-keyboard). +The application supports varied physical layouts and therefore matrices. +This physical variability is its main feature; its QMK firmware is ordinary. + +Consult the general [Dactyl-ManuForm readme](../readme.md). + +## The `62key` layout + +This folder represents the default build target of the Clojure application +as of its version 0.4.0. The default keymap for this layout has a QWERTY base +layer but is intended for running Colemak on the OS side with the i3 tiling +window manager. It’s also got a layer that forces Colemak from the QMK side. diff --git a/keyboards/handwired/dactyl_promicro/config.h b/keyboards/handwired/dactyl_promicro/config.h index f81b3de51..3c0b541d1 100644 --- a/keyboards/handwired/dactyl_promicro/config.h +++ b/keyboards/handwired/dactyl_promicro/config.h @@ -46,7 +46,7 @@ along with this program. If not, see <http://www.gnu.org/licenses/>. #define MOUSEKEY_WHEEL_DELAY 0 /* Set 0 if debouncing isn't needed */ -#define DEBOUNCING_DELAY 5 +#define DEBOUNCE 5 /* serial.c configuration for split keyboard */ #define SOFT_SERIAL_PIN D0 diff --git a/keyboards/handwired/daishi/config.h b/keyboards/handwired/daishi/config.h new file mode 100644 index 000000000..15ff6a6a6 --- /dev/null +++ b/keyboards/handwired/daishi/config.h @@ -0,0 +1,61 @@ +/* +Copyright 2019 Crokto + +This program is free software: you can redistribute it and/or modify +it under the terms of the GNU General Public License as published by +the Free Software Foundation, either version 2 of the License, or +(at your option) any later version. + +This program is distributed in the hope that it will be useful, +but WITHOUT ANY WARRANTY; without even the implied warranty of +MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +GNU General Public License for more details. + +You should have received a copy of the GNU General Public License +along with this program. If not, see <http://www.gnu.org/licenses/>. +*/ + +#pragma once + +#include "config_common.h" + +/* USB Device descriptor parameter */ +#define VENDOR_ID 0x6D6D +#define PRODUCT_ID 0x0001 +#define DEVICE_VER 0x0001 +#define MANUFACTURER MetaMechs +#define PRODUCT Daishi +#define DESCRIPTION Compact Battlecruiser + +/* key matrix size */ +#define MATRIX_ROWS 7 +#define MATRIX_COLS 18 + +/* + * Keyboard Matrix Assignments + * + * Change this to how you wired your keyboard + * COLS: AVR pins used for columns, left to right + * ROWS: AVR pins used for rows, top to bottom + * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode) + * ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode) + * +*/ +#define MATRIX_ROW_PINS { D6, D7, E0, E1, C0, C1, C2 } +#define MATRIX_COL_PINS { E6, E7, E3, B0, B1, B2, A6, A5, A4, A3, A2, A1, A0, F7, F6, F5, F4, F3 } +#define UNUSED_PINS + +/* COL2ROW, ROW2COL, or CUSTOM_MATRIX */ +#define DIODE_DIRECTION COL2ROW + +/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */ +#define DEBOUNCE 5 + +/* Set up rotary encoder */ +#define NUMBER_OF_ENCODERS 1 +#define ENCODERS_PAD_A { F1 } +#define ENCODERS_PAD_B { F0 } +#define ENCODER_RESOLUTION 2 + +/* Set delay for tap_code on rotary encoder */ +#define TAP_CODE_DELAY 10
\ No newline at end of file diff --git a/keyboards/handwired/daishi/daishi.c b/keyboards/handwired/daishi/daishi.c new file mode 100644 index 000000000..dcd2cd0d1 --- /dev/null +++ b/keyboards/handwired/daishi/daishi.c @@ -0,0 +1,22 @@ +#include "daishi.h" + +void matrix_init_kb(void) { + // put your keyboard start-up code here + // runs once when the firmware starts up + + matrix_init_user(); +} + +void matrix_scan_kb(void) { + // put your looping keyboard code here + // runs every cycle (a lot) + + matrix_scan_user(); +} + +bool process_record_kb(uint16_t keycode, keyrecord_t *record) { + // put your per-action keyboard code here + // runs for every action, just before processing by the firmware + + return process_record_user(keycode, record); +}
\ No newline at end of file diff --git a/keyboards/handwired/daishi/daishi.h b/keyboards/handwired/daishi/daishi.h new file mode 100644 index 000000000..49e377589 --- /dev/null +++ b/keyboards/handwired/daishi/daishi.h @@ -0,0 +1,25 @@ +#pragma once + +#include "quantum.h" + +#define encoder_update(clockwise) encoder_update_user(uint8_t index, clockwise) + +// The first section contains all of the arguments +// The second converts the arguments into a two-dimensional array +#define LAYOUT( \ + K00, K01, K02, K03, K04, K05, K06, K07, K08, K09, K0A, K0B, K0C, K0D, K0E, K0F, K0G, K0H, \ + K10, K11, K12, K13, K14, K15, K16, K17, K18, K19, K1A, K1B, K1C, K1D, K1E, K1F, K1G, K1H, \ + K20, K21, K22, K23, K24, K25, K26, K27, K28, K29, K2A, K2B, K2C, K2D, K2E, K2F, K2G, K2H, \ + K30, K31, K32, K33, K34, K35, K36, K37, K38, K39, K3A, K3B, K3C, K3D, K3E, K3F, K3G, K3H, \ + K40, K41, K42, K43, K44, K45, K46, K47, K48, K49, K4A, K4B, K4C, K4E, K4F, K4G, K4H, \ + K50, K51, K52, K53, K54, K55, K56, K57, K58, K59, K5A, K5B, K5D, K5E, K5F, K5G, K5H, \ + K60, K61, K62, K65, K69, K6A, K6C, K6D, K6E, K6F, K6G \ +){ \ + { K00, K01, K02, K03, K04, K05, K06, K07, K08, K09, K0A, K0B, K0C, K0D, K0E, K0F, K0G, K0H }, \ + { K10, K11, K12, K13, K14, K15, K16, K17, K18, K19, K1A, K1B, K1C, K1D, K1E, K1F, K1G, K1H }, \ + { K20, K21, K22, K23, K24, K25, K26, K27, K28, K29, K2A, K2B, K2C, K2D, K2E, K2F, K2G, K2H }, \ + { K30, K31, K32, K33, K34, K35, K36, K37, K38, K39, K3A, K3B, K3C, K3D, K3E, K3F, K3G, K3H }, \ + { K40, K41, K42, K43, K44, K45, K46, K47, K48, K49, K4A, K4B, K4C, KC_NO, K4E, K4F, K4G, K4H }, \ + { K50, K51, K52, K53, K54, K55, K56, K57, K58, K59, K5A, K5B, KC_NO, K5D, K5E, K5F, K5G, K5H }, \ + { K60, K61, K62, KC_NO, KC_NO, K65, KC_NO, KC_NO, KC_NO, K69, K6A, KC_NO, K6C, K6D, K6E, K6F, K6G, KC_NO } \ +} diff --git a/keyboards/handwired/daishi/keymaps/default/keymap.c b/keyboards/handwired/daishi/keymaps/default/keymap.c new file mode 100644 index 000000000..c0baf7006 --- /dev/null +++ b/keyboards/handwired/daishi/keymaps/default/keymap.c @@ -0,0 +1,124 @@ +#include QMK_KEYBOARD_H + +// Layer shorthand +#define _QW 0 +#define _FN 1 + +enum custom_keycodes { + M_EXAMPLE1 = SAFE_RANGE, + M_EXAMPLE2, + DYNAMIC_MACRO_RANGE, +}; + +#include "dynamic_macro.h" + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { + +/* QWERTY + * .-----------------------------------------------------------------------------------------------------------------------------------------------------------------. + * | ESC | | | | | | | | | | DM1 | DM2 | DMSTOP | PRINT | SCROLL | PAUSE | FN | VOL | + * |--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------------------------------------------| + * | F1 | F2 | F3 | F4 | F5 | F6 | F7 | F8 | F9 | F10 | F11 | F12 | DEL | HOME | PGUP | END | INS | NUM | + * |--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------------------------------------------| + * | ` | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 0 | - | = | BACK | PGDN | / | * | - | + * |--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------------------------------------------| + * | TAB | Q | W | E | R | T | Y | U | I | O | P | [ | ] | \ | 7 | 8 | 9 | + | + * |--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------------------------------------------| + * | CAPS | A | S | D | F | G | H | J | K | L | ; | ' | ENTER | | 4 | 5 | 6 | = | + * |--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------------------------------------------| + * | LSHIFT | Z | X | C | V | B | N | M | , | . | / | SHIFT | | UP | 1 | 2 | 3 | ENTER | + * |--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------------------------------------------| + * | LCTRL | LGUI | LALT | | | SPACE | | | | RALT | RCTRL | | LEFT | DOWN | RIGHT | 0 | . | | + * |--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------------------------------------------' + */ + + [_QW] = LAYOUT( /* QWERTY */ + KC_ESC , _______, _______, _______, _______, _______, _______, _______, _______, _______,DYN_MACRO_PLAY1,DYN_MACRO_PLAY2,DYN_REC_STOP, KC_PSCR, KC_SLCK, KC_PAUS, MO(_FN), KC_MUTE, + KC_F1 , KC_F2 , KC_F3 , KC_F4 , KC_F5 , KC_F6 , KC_F7 , KC_F8 , KC_F9 , KC_F10 , KC_F11 , KC_F12 , KC_DEL , KC_HOME, KC_PGUP, KC_END , KC_INS , KC_NLCK, + KC_GRV , KC_1 , KC_2 , KC_3 , KC_4 , KC_5 , KC_6 , KC_7 , KC_8 , KC_9 , KC_0 , KC_MINS, KC_EQL , KC_BSPC, KC_PGDN, KC_PSLS, KC_PAST, KC_PMNS, + KC_TAB , KC_Q , KC_W , KC_E , KC_R , KC_T , KC_Y , KC_U , KC_I , KC_O , KC_P , KC_LBRC, KC_RBRC, KC_BSLS, KC_P7 , KC_P8 , KC_P9 , KC_PPLS, + KC_CAPS, KC_A , KC_S , KC_D , KC_F , KC_G , KC_H , KC_J , KC_K , KC_L , KC_SCLN, KC_QUOT, KC_ENT , KC_P4 , KC_P5 , KC_P6 , KC_EQL , + KC_LSFT, KC_Z , KC_X , KC_C , KC_V , KC_B , KC_N , KC_M , KC_COMM, KC_DOT , KC_SLSH, KC_RSFT, KC_UP , KC_P1 , KC_P2 , KC_P3 , KC_PENT, + KC_LCTL, KC_LGUI, KC_LALT, KC_SPC , KC_RALT, KC_RCTL, KC_LEFT, KC_DOWN, KC_RGHT, KC_P0 , KC_PDOT + ), + +/* FN + * .-----------------------------------------------------------------------------------------------------------------------------------------------------------------. + * | RESET | F13 | F14 | F15 | f16 | f17 | f18 | F19 | F20 | F21 | DM1 R | DM2 R | DMSTOP | | | | FN | DEBUG | + * |--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------------------------------------------| + * | | | | | | | | | | | | | | | | | | | + * |--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------------------------------------------| + * | | | | | | | | | | | | | | | | | | | + * |--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------------------------------------------| + * | | | | | | | | | | | | | | | | | | | + * |--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------------------------------------------| + * | | | | | | | | | | | | | | | | | | | + * |--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------------------------------------------| + * | | | | | | | | | | | | | | | | | | | + * |--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------------------------------------------| + * | | | | | | | | | | | | | | | | | | | + * |--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------------------------------------------' + */ + + [_FN] = LAYOUT( /* Function */ + RESET , KC_F13 , KC_F14 , KC_F15 , KC_F16 , KC_F17 , KC_F18 , KC_F19 , KC_F20 , KC_F21 ,DYN_REC_START1,DYN_REC_START2,DYN_REC_STOP, _______, _______, _______, MO(_FN), DEBUG, + _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, + _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, + _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, + _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, + _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, + _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______ + ) +}; + +bool process_record_user(uint16_t keycode, keyrecord_t *record) { + if (!process_record_dynamic_macro(keycode, record)) { + return false; + } + if (record->event.pressed) { + switch(keycode) { + case M_EXAMPLE1: + SEND_STRING("This is an example macro!"SS_TAP(X_ENTER)); //prints "This is an example macro!" and hits Enter + return false; + case M_EXAMPLE2: + SEND_STRING("This is a another example!"SS_TAP(X_ENTER)); //prints "This is a another example!" and hits Enter + return false; + } + } + return true; +}; + +void encoder_update(bool clockwise) { + if (clockwise) { + tap_code(KC_VOLU); + } else { + tap_code(KC_VOLD); + } +} + +void matrix_init_user(void) { + // Call the keymap level matrix init. + + // Set our LED pins as output + setPinOutput(C4); + setPinOutput(C5); + setPinOutput(C6); +} + +void led_set_kb(uint8_t usb_led) { + if (IS_LED_OFF(usb_led, USB_LED_NUM_LOCK)) { + writePinLow(C4); + } else { + writePinHigh(C4); + } + if (IS_LED_OFF(usb_led, USB_LED_CAPS_LOCK)) { + writePinLow(C5); + } else { + writePinHigh(C5); + } + if (IS_LED_OFF(usb_led, USB_LED_SCROLL_LOCK)) { + writePinLow(C6); + } else { + writePinHigh(C6); + } +}
\ No newline at end of file diff --git a/keyboards/handwired/daishi/keymaps/default/readme.md b/keyboards/handwired/daishi/keymaps/default/readme.md new file mode 100644 index 000000000..bed7fcb23 --- /dev/null +++ b/keyboards/handwired/daishi/keymaps/default/readme.md @@ -0,0 +1,5 @@ +# Default Daishi Layout + + + +This is the default layout that comes on the Daishi. For more information on the design of this layout, check out [kb.metamechs.com](http://kb.metamechs.com/daishi/). diff --git a/keyboards/handwired/daishi/readme.md b/keyboards/handwired/daishi/readme.md new file mode 100644 index 000000000..88ac8ea79 --- /dev/null +++ b/keyboards/handwired/daishi/readme.md @@ -0,0 +1,15 @@ +# Daishi + + + +A compact battlecruiser using the CBC1 PCB. [More info on kb.metamechs.com](http://kb.metamechs.com/daishi/) + +Keyboard Maintainer: [Crokto](https://github.com/Croktopus/) +Hardware Supported: CBC1 PCB +Hardware Availability: [kb.metamechs.com](http://kb.metamechs.com/daishi/get-your-own-daishi/) + +Make example for this keyboard (after setting up your build environment): + + make handwired/daishi:default + +See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs). diff --git a/keyboards/handwired/daishi/rules.mk b/keyboards/handwired/daishi/rules.mk new file mode 100644 index 000000000..ece1eaaac --- /dev/null +++ b/keyboards/handwired/daishi/rules.mk @@ -0,0 +1,66 @@ +# MCU name +MCU = at90usb1286 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + +# Boot Section Size in *bytes* +# Teensy halfKay 512 +# Teensy++ halfKay 1024 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +# USBaspLoader 2048 +BOOTLOADER = atmel-dfu + +# QMK Build Options +# change to "no" to disable the options, or define them in the Makefile in +# the appropriate keymap folder that will get included automatically +# +BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE = no # Mouse keys(+4700) +EXTRAKEY_ENABLE = yes # Audio control and System control(+450) +CONSOLE_ENABLE = yes # Console for debug(+400) +COMMAND_ENABLE = no # Commands for debug and configuration +NKRO_ENABLE = yes # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality +MIDI_ENABLE = no # MIDI support (+2400 to 4200, depending on config) +AUDIO_ENABLE = no # Audio output on port C6 +UNICODE_ENABLE = no # Unicode +BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID +RGBLIGHT_ENABLE = no # Enable WS2812 RGB underlight. Do not enable this with audio at the same time. +SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend +ENCODER_ENABLE = yes # Add rotary encoder support
\ No newline at end of file diff --git a/keyboards/handwired/datahand/config.h b/keyboards/handwired/datahand/config.h index a269775f3..c7a0a43de 100644 --- a/keyboards/handwired/datahand/config.h +++ b/keyboards/handwired/datahand/config.h @@ -33,7 +33,7 @@ //#define DIODE_DIRECTION /* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */ -#define DEBOUNCING_DELAY 0 +#define DEBOUNCE 0 /* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ #define LOCKING_SUPPORT_ENABLE diff --git a/keyboards/handwired/downbubble/config.h b/keyboards/handwired/downbubble/config.h index 4b2bd92e4..f2628cb70 100644 --- a/keyboards/handwired/downbubble/config.h +++ b/keyboards/handwired/downbubble/config.h @@ -80,7 +80,7 @@ along with this program. If not, see <http://www.gnu.org/licenses/>. // #endif /* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */ -#define DEBOUNCING_DELAY 5 +#define DEBOUNCE 5 /* define if matrix has ghost (lacks anti-ghosting diodes) */ //#define MATRIX_HAS_GHOST diff --git a/keyboards/handwired/fivethirteen/config.h b/keyboards/handwired/fivethirteen/config.h index 685d421b1..951122297 100644 --- a/keyboards/handwired/fivethirteen/config.h +++ b/keyboards/handwired/fivethirteen/config.h @@ -54,7 +54,7 @@ along with this program. If not, see <http://www.gnu.org/licenses/>. // #define BACKLIGHT_LEVELS 3 /* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */ -#define DEBOUNCING_DELAY 5 +#define DEBOUNCE 5 /* define if matrix has ghost (lacks anti-ghosting diodes) */ //#define MATRIX_HAS_GHOST diff --git a/keyboards/handwired/frenchdev/matrix.c b/keyboards/handwired/frenchdev/matrix.c index 4263555e9..26c2b3126 100644 --- a/keyboards/handwired/frenchdev/matrix.c +++ b/keyboards/handwired/frenchdev/matrix.c @@ -5,11 +5,6 @@ The "column" and "row" in here actually refers to the opposite on the keyboard see definition of KEYMAP in v1.h, the grid is transposed so that a "row" in here is actually a "column" on the physical keyboard Nicolas -Note for ErgoDox EZ customizers: Here be dragons! -This is not a file you want to be messing with. -All of the interesting stuff for you is under keymaps/ :) -Love, Erez - Copyright 2013 Oleg Kostyuk <cub.uanic@gmail.com> Copyright 2013 Nicolas Poirey <nicolas.poirey@gmail.com> diff --git a/keyboards/handwired/gamenum/config.h b/keyboards/handwired/gamenum/config.h index 180b1b01a..ff60aa529 100644 --- a/keyboards/handwired/gamenum/config.h +++ b/keyboards/handwired/gamenum/config.h @@ -54,7 +54,7 @@ along with this program. If not, see <http://www.gnu.org/licenses/>. // #define BACKLIGHT_LEVELS 3 /* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */ -#define DEBOUNCING_DELAY 5 +#define DEBOUNCE 5 /* define if matrix has ghost (lacks anti-ghosting diodes) */ //#define MATRIX_HAS_GHOST diff --git a/keyboards/handwired/hacked_motospeed/config.h b/keyboards/handwired/hacked_motospeed/config.h index 59300e0d2..1a341c0f4 100644 --- a/keyboards/handwired/hacked_motospeed/config.h +++ b/keyboards/handwired/hacked_motospeed/config.h @@ -84,7 +84,7 @@ along with this program. If not, see <http://www.gnu.org/licenses/>. // #endif /* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */ -#define DEBOUNCING_DELAY 5 +#define DEBOUNCE 5 /* define if matrix has ghost (lacks anti-ghosting diodes) */ #define MATRIX_HAS_GHOST diff --git a/keyboards/handwired/hexon38/config.h b/keyboards/handwired/hexon38/config.h index 5453eda54..e9e1eb4d2 100644 --- a/keyboards/handwired/hexon38/config.h +++ b/keyboards/handwired/hexon38/config.h @@ -31,7 +31,7 @@ #endif /* Set 0 if debouncing isn't needed */ -#define DEBOUNCING_DELAY 5 +#define DEBOUNCE 5 #ifdef RGB_DI_PIN #define RGBLIGHT_ANIMATIONS diff --git a/keyboards/handwired/hnah40/config.h b/keyboards/handwired/hnah40/config.h new file mode 100644 index 000000000..b7a4105d0 --- /dev/null +++ b/keyboards/handwired/hnah40/config.h @@ -0,0 +1,220 @@ +/* Copyright 2018 HnahKB + +This program is free software: you can redistribute it and/or modify +it under the terms of the GNU General Public License as published by +the Free Software Foundation, either version 2 of the License, or +(at your option) any later version. + +This program is distributed in the hope that it will be useful, +but WITHOUT ANY WARRANTY; without even the implied warranty of +MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +GNU General Public License for more details. + +You should have received a copy of the GNU General Public License +along with this program. If not, see <http://www.gnu.org/licenses/>. +*/ + +#pragma once + +#include "config_common.h" + +/* USB Device descriptor parameter */ +#define VENDOR_ID 0xFEED +#define PRODUCT_ID 0x0000 +#define DEVICE_VER 0x0002 +#define MANUFACTURER HnahKB +#define PRODUCT hnah40 +#define DESCRIPTION Custom 40% PCB + +/* key matrix size */ +#define MATRIX_ROWS 4 +#define MATRIX_COLS 11 + +/* + * Keyboard Matrix Assignments + * + * Change this to how you wired your keyboard + * COLS: AVR pins used for columns, left to right + * ROWS: AVR pins used for rows, top to bottom + * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode) + * ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode) + * +*/ +#define MATRIX_ROW_PINS { B4, B5, B3, D4 } +#define MATRIX_COL_PINS { B0, D7, D6, D5, B2, B1, C0, C1, C2, C3, D1 } +#define UNUSED_PINS + +/* COL2ROW, ROW2COL*/ +#define DIODE_DIRECTION COL2ROW + +// #define BACKLIGHT_PIN B7 +// #define BACKLIGHT_BREATHING +// #define BACKLIGHT_LEVELS 3 + +// #define RGB_DI_PIN E2 +// #ifdef RGB_DI_PIN +// #define RGBLIGHT_ANIMATIONS +// #define RGBLED_NUM 16 +// #define RGBLIGHT_HUE_STEP 8 +// #define RGBLIGHT_SAT_STEP 8 +// #define RGBLIGHT_VAL_STEP 8 +// #endif + +/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */ +#define DEBOUNCING 5 + +/* define if matrix has ghost (lacks anti-ghosting diodes) */ +//#define MATRIX_HAS_GHOST + +/* number of backlight levels */ + +/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ +#define LOCKING_SUPPORT_ENABLE +/* Locking resynchronize hack */ +#define LOCKING_RESYNC_ENABLE + +/* If defined, GRAVE_ESC will always act as ESC when CTRL is held. + * This is userful for the Windows task manager shortcut (ctrl+shift+esc). + */ +// #define GRAVE_ESC_CTRL_OVERRIDE + +/* + * Force NKRO + * + * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved + * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the + * makefile for this to work.) + * + * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N) + * until the next keyboard reset. + * + * NKRO may prevent your keystrokes from being detected in the BIOS, but it is + * fully operational during normal computer usage. + * + * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N) + * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by + * bootmagic, NKRO mode will always be enabled until it is toggled again during a + * power-up. + * + */ +//#define FORCE_NKRO + +/* + * Magic Key Options + * + * Magic keys are hotkey commands that allow control over firmware functions of + * the keyboard. They are best used in combination with the HID Listen program, + * found here: https://www.pjrc.com/teensy/hid_listen.html + * + * The options below allow the magic key functionality to be changed. This is + * useful if your keyboard/keypad is missing keys and you want magic key support. + * + */ + + + +/* control how magic key switches layers */ +//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS true +//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS true +//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM false + +/* override magic key keymap */ +//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS +//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS +//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM +//#define MAGIC_KEY_HELP1 H +//#define MAGIC_KEY_HELP2 SLASH +//#define MAGIC_KEY_DEBUG D +//#define MAGIC_KEY_DEBUG_MATRIX X +//#define MAGIC_KEY_DEBUG_KBD K +//#define MAGIC_KEY_DEBUG_MOUSE M +//#define MAGIC_KEY_VERSION V +//#define MAGIC_KEY_STATUS S +//#define MAGIC_KEY_CONSOLE C +//#define MAGIC_KEY_LAYER0_ALT1 ESC +//#define MAGIC_KEY_LAYER0_ALT2 GRAVE +//#define MAGIC_KEY_LAYER0 0 +//#define MAGIC_KEY_LAYER1 1 +//#define MAGIC_KEY_LAYER2 2 +//#define MAGIC_KEY_LAYER3 3 +//#define MAGIC_KEY_LAYER4 4 +//#define MAGIC_KEY_LAYER5 5 +//#define MAGIC_KEY_LAYER6 6 +//#define MAGIC_KEY_LAYER7 7 +//#define MAGIC_KEY_LAYER8 8 +//#define MAGIC_KEY_LAYER9 9 +//#define MAGIC_KEY_BOOTLOADER PAUSE +//#define MAGIC_KEY_LOCK CAPS +//#define MAGIC_KEY_EEPROM E +//#define MAGIC_KEY_NKRO N +//#define MAGIC_KEY_SLEEP_LED Z + +/* + * Feature disable options + * These options are also useful to firmware size reduction. + */ + +/* disable debug print */ +//#define NO_DEBUG + +/* disable print */ +//#define NO_PRINT + +/* disable action features */ +//#define NO_ACTION_LAYER +//#define NO_ACTION_TAPPING +//#define NO_ACTION_ONESHOT +//#define NO_ACTION_MACRO +//#define NO_ACTION_FUNCTION + +/* + * MIDI options + */ + +/* Prevent use of disabled MIDI features in the keymap */ +//#define MIDI_ENABLE_STRICT 1 + +/* enable basic MIDI features: + - MIDI notes can be sent when in Music mode is on +*/ +//#define MIDI_BASIC + +/* enable advanced MIDI features: + - MIDI notes can be added to the keymap + - Octave shift and transpose + - Virtual sustain, portamento, and modulation wheel + - etc. +*/ +//#define MIDI_ADVANCED + +/* override number of MIDI tone keycodes (each octave adds 12 keycodes and allocates 12 bytes) */ +//#define MIDI_TONE_KEYCODE_OCTAVES 1 + +/* + * HD44780 LCD Display Configuration + */ +/* +#define LCD_LINES 2 //< number of visible lines of the display +#define LCD_DISP_LENGTH 16 //< visibles characters per line of the display + +#define LCD_IO_MODE 1 //< 0: memory mapped mode, 1: IO port mode + +#if LCD_IO_MODE +#define LCD_PORT PORTB //< port for the LCD lines +#define LCD_DATA0_PORT LCD_PORT //< port for 4bit data bit 0 +#define LCD_DATA1_PORT LCD_PORT //< port for 4bit data bit 1 +#define LCD_DATA2_PORT LCD_PORT //< port for 4bit data bit 2 +#define LCD_DATA3_PORT LCD_PORT //< port for 4bit data bit 3 +#define LCD_DATA0_PIN 4 //< pin for 4bit data bit 0 +#define LCD_DATA1_PIN 5 //< pin for 4bit data bit 1 +#define LCD_DATA2_PIN 6 //< pin for 4bit data bit 2 +#define LCD_DATA3_PIN 7 //< pin for 4bit data bit 3 +#define LCD_RS_PORT LCD_PORT //< port for RS line +#define LCD_RS_PIN 3 //< pin for RS line +#define LCD_RW_PORT LCD_PORT //< port for RW line +#define LCD_RW_PIN 2 //< pin for RW line +#define LCD_E_PORT LCD_PORT //< port for Enable line +#define LCD_E_PIN 1 //< pin for Enable line +#endif +*/ + diff --git a/keyboards/handwired/hnah40/hnah40.c b/keyboards/handwired/hnah40/hnah40.c new file mode 100644 index 000000000..0f08136c2 --- /dev/null +++ b/keyboards/handwired/hnah40/hnah40.c @@ -0,0 +1,43 @@ +/* Copyright 2019 HnahKB + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ +#include "hnah40.h" + +void matrix_init_kb(void) { + // put your keyboard start-up code here + // runs once when the firmware starts up + + matrix_init_user(); +} + +void matrix_scan_kb(void) { + // put your looping keyboard code here + // runs every cycle (a lot) + + matrix_scan_user(); +} + +bool process_record_kb(uint16_t keycode, keyrecord_t *record) { + // put your per-action keyboard code here + // runs for every action, just before processing by the firmware + + return process_record_user(keycode, record); +} + +void led_set_kb(uint8_t usb_led) { + // put your keyboard LED indicator (ex: Caps Lock LED) toggling code here + + led_set_user(usb_led); +} diff --git a/keyboards/handwired/hnah40/hnah40.h b/keyboards/handwired/hnah40/hnah40.h new file mode 100644 index 000000000..28e09f668 --- /dev/null +++ b/keyboards/handwired/hnah40/hnah40.h @@ -0,0 +1,38 @@ +/* Copyright 2019 HnahKB + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ +#pragma once + +#include "quantum.h" + +// This a shortcut to help you visually see your layout. +// The following is an example using the Planck MIT layout +// The first section contains all of the arguments representing the physical +// layout of the board and position of the keys +// The second converts the arguments into a two-dimensional array which +// represents the switch matrix. + +#define LAYOUT( \ + k00, k01, k02, k03, k04, k05, k06, k07, k08, k09, k0A, k39, \ + k10, k11, k12, k13, k14, k15, k16, k17, k18, k19, k1A, \ + k20, k21, k22, k23, k24, k25, k26, k27, k28, k29, k2A, \ + k30, k31, k32, k33, k35, k37, k38, k3A\ +) \ +{ \ + { k00, k01, k02, k03, k04, k05, k06, k07, k08, k09, k0A }, \ + { k10, k11, k12, k13, k14, k15, k16, k17, k18, k19, k1A }, \ + { k20, k21, k22, k23, k24, k25, k26, k27, k28, k29, k2A }, \ + { k30, k31, k32, k33, KC_NO, k35, KC_NO, k37, k38, k39, k3A }, \ +} diff --git a/keyboards/handwired/hnah40/info.json b/keyboards/handwired/hnah40/info.json new file mode 100644 index 000000000..6a577a520 --- /dev/null +++ b/keyboards/handwired/hnah40/info.json @@ -0,0 +1,54 @@ +{ + "keyboard_name": "Hnah40", + "url": "https://github.com/vuhopkep/PCB/tree/master/Hnah40-Atmega328p/PCB_V1/PCB", + "maintainer": "HnahKB", + "width": 12, + "height": 4, + "layouts": { + "LAYOUT": { + "layout": [ + {"label":"Esc", "x":0, "y":0}, + {"label":"Q", "x":1, "y":0}, + {"label":"W", "x":2, "y":0}, + {"label":"E", "x":3, "y":0}, + {"label":"R", "x":4, "y":0}, + {"label":"T", "x":5, "y":0}, + {"label":"Y", "x":6, "y":0}, + {"label":"U", "x":7, "y":0}, + {"label":"I", "x":8, "y":0}, + {"label":"O", "x":9, "y":0}, + {"label":"P", "x":10, "y":0}, + {"label":"BSPC", "x":11, "y":0}, + {"label":"Tab", "x":0, "y":1, "w":1.5}, + {"label":"A", "x":1.5, "y":1}, + {"label":"S", "x":2.5, "y":1}, + {"label":"D", "x":3.5, "y":1}, + {"label":"F", "x":4.5, "y":1}, + {"label":"G", "x":5.5, "y":1}, + {"label":"H", "x":6.5, "y":1}, + {"label":"J", "x":7.5, "y":1}, + {"label":"K", "x":8.5, "y":1}, + {"label":"L", "x":9.5, "y":1}, + {"label":"Enter", "x":10.5, "y":1, "w":1.5}, + {"label":"Shift", "x":0, "y":2, "w":1.75}, + {"label":"Z", "x":1.75, "y":2}, + {"label":"X", "x":2.75, "y":2}, + {"label":"C", "x":3.75, "y":2}, + {"label":"V", "x":4.75, "y":2}, + {"label":"B", "x":5.75, "y":2}, + {"label":"N", "x":6.75, "y":2}, + {"label":"M", "x":7.75, "y":2}, + {"label":",", "x":8.75, "y":2}, + {"label":"Shift", "x":9.75, "y":2, "w":2.25}, + {"label":"Ctrl", "x":0, "y":3, "w":1.25}, + {"label":"Win", "x":1.25, "y":3, "w":1.5}, + {"label":"Alt", "x":2.75, "y":3, "w":1.25}, + {"label":"Space", "x":4, "y":3, "w":2}, + {"label":"Space", "x":6, "y":3, "w":2}, + {"label":"App", "x":8, "y":3, "w":1.25}, + {"label":"Fn", "x":9.25, "y":3, "w":1.5}, + {"label":"Ctrl", "x":10.75, "y":3, "w":1.25} + ] + } + } +}
\ No newline at end of file diff --git a/keyboards/handwired/hnah40/keymaps/default/config.h b/keyboards/handwired/hnah40/keymaps/default/config.h new file mode 100644 index 000000000..74412a948 --- /dev/null +++ b/keyboards/handwired/hnah40/keymaps/default/config.h @@ -0,0 +1,18 @@ +/* Copyright 2019 HnahKB + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#pragma once + +// place overrides here diff --git a/keyboards/handwired/hnah40/keymaps/default/keymap.c b/keyboards/handwired/hnah40/keymaps/default/keymap.c new file mode 100644 index 000000000..2fc67ba5e --- /dev/null +++ b/keyboards/handwired/hnah40/keymaps/default/keymap.c @@ -0,0 +1,48 @@ +/* Copyright 2019 HnahKB + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ +#include QMK_KEYBOARD_H + +// Defines the keycodes used by our macros in process_record_user +enum hnah_layers{ + _QWERTY, + _LOWER, + _RAISE +}; + + +#define LOWER MO(_LOWER) +#define RAISE MO(_RAISE) + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { + [_QWERTY] = LAYOUT( /* Base */ + KC_ESC, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_BSPC, + LT(RAISE, KC_CAPS), KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_ENT, + KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_RSFT, + KC_LCTL, KC_LGUI, KC_LALT, KC_SPACE, KC_SPACE, KC_APP, LOWER, KC_RCTL + ), + [_LOWER] = LAYOUT( /* Base */ + RESET, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_DEL, + RAISE, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_MINS, KC_EQL, KC_SCLN, KC_QUOT, + KC_LSFT, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, KC_COMM, KC_DOT, KC_SLSH, KC_SLSH, + KC_LCTL, KC_LGUI, KC_LALT, KC_SPACE, KC_SPACE, KC_APP, KC_TRNS, KC_RCTL + ), + [_RAISE] = LAYOUT( /* Base */ + RESET, KC_1, KC_UP, RGB_TOG, RGB_MOD, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_DEL, + KC_TRNS, KC_LEFT, KC_DOWN, KC_RGHT , RGB_HUI, RGB_HUD, RGB_SAI, RGB_SAD, RGB_VAI, RGB_VAD, KC_ENT, + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_UP, KC_TRNS, + KC_TRNS, KC_TRNS, KC_TRNS, KC_SPACE, KC_SPACE, KC_LEFT, KC_DOWN, KC_RGHT + ), +}; diff --git a/keyboards/handwired/hnah40/keymaps/default/readme.md b/keyboards/handwired/hnah40/keymaps/default/readme.md new file mode 100644 index 000000000..b948ef964 --- /dev/null +++ b/keyboards/handwired/hnah40/keymaps/default/readme.md @@ -0,0 +1 @@ +
\ No newline at end of file diff --git a/keyboards/handwired/hnah40/readme.md b/keyboards/handwired/hnah40/readme.md new file mode 100644 index 000000000..20e2d7127 --- /dev/null +++ b/keyboards/handwired/hnah40/readme.md @@ -0,0 +1,20 @@ +# hnah40 + + + +A custom 40% keyboard PCB, insprired by Plaid keyboard from hsgw + + +Keyboard Maintainer: [vuhopkep](https://github.com/vuhopkep) +Hardware Availability: https://github.com/vuhopkep/PCB/tree/master/Hnah40-Atmega328p + +Make example for this keyboard (after setting up your build environment): + + make handwired/hnah40:default:program + +## Bootloader +use usbasploader from hsgw. +https://github.com/hsgw/USBaspLoader/tree/plaid + + +See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs). diff --git a/keyboards/handwired/hnah40/rules.mk b/keyboards/handwired/hnah40/rules.mk new file mode 100644 index 000000000..efd11bfa5 --- /dev/null +++ b/keyboards/handwired/hnah40/rules.mk @@ -0,0 +1,73 @@ +# MCU name +MCU = atmega328p +PROTOCOL = VUSB + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + +BOOTLOADER = bootloadHID + +# Flash program via avrdude, but default command is not suitable. +# You can use hnah40:default:program +PROGRAM_CMD = avrdude -c usbasp -p m328p -U flash:w:$(BUILD_DIR)/$(TARGET).hex + + +# disable debug code +OPT_DEFS = -DDEBUG_LEVEL=0 + + +# Build Options +# change yes to no to disable +# +BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE = yes # Mouse keys(+4700) +EXTRAKEY_ENABLE = yes # Audio control and System control(+450) +CONSOLE_ENABLE = no # Console for debug(+400) +COMMAND_ENABLE = no # Commands for debug and configuration +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend +# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +NKRO_ENABLE = no # USB Nkey Rollover +BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality on B7 by default +RGBLIGHT_ENABLE = no # Enable keyboard RGB underglow +MIDI_ENABLE = no # MIDI support (+2400 to 4200, depending on config) +UNICODE_ENABLE = no # Unicode +BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID +AUDIO_ENABLE = no # Audio output on port C6 +FAUXCLICKY_ENABLE = no # Use buzzer to emulate clicky switches +HD44780_ENABLE = no # Enable support for HD44780 based LCDs (+400) +NO_UART = yes +NO_SUSPEND_POWER_DOWN = yes
\ No newline at end of file diff --git a/keyboards/handwired/hnah40/usbconfig.h b/keyboards/handwired/hnah40/usbconfig.h new file mode 100644 index 000000000..cbd37c34d --- /dev/null +++ b/keyboards/handwired/hnah40/usbconfig.h @@ -0,0 +1,397 @@ +/* Name: usbconfig.h + * Project: V-USB, virtual USB port for Atmel's(r) AVR(r) microcontrollers + * Author: Christian Starkjohann + * Creation Date: 2005-04-01 + * Tabsize: 4 + * Copyright: (c) 2005 by OBJECTIVE DEVELOPMENT Software GmbH + * License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt) + * This Revision: $Id: usbconfig-prototype.h 785 2010-05-30 17:57:07Z cs $ + */ + +#ifndef __usbconfig_h_included__ +#define __usbconfig_h_included__ + +#include "config.h" + +/* +General Description: +This file is an example configuration (with inline documentation) for the USB +driver. It configures V-USB for USB D+ connected to Port D bit 2 (which is +also hardware interrupt 0 on many devices) and USB D- to Port D bit 4. You may +wire the lines to any other port, as long as D+ is also wired to INT0 (or any +other hardware interrupt, as long as it is the highest level interrupt, see +section at the end of this file). +*/ + +/* ---------------------------- Hardware Config ---------------------------- */ + +#define USB_CFG_IOPORTNAME D +/* This is the port where the USB bus is connected. When you configure it to + * "B", the registers PORTB, PINB and DDRB will be used. + */ +#define USB_CFG_DMINUS_BIT 3 +/* This is the bit number in USB_CFG_IOPORT where the USB D- line is connected. + * This may be any bit in the port. + */ +#define USB_CFG_DPLUS_BIT 2 +/* This is the bit number in USB_CFG_IOPORT where the USB D+ line is connected. + * This may be any bit in the port. Please note that D+ must also be connected + * to interrupt pin INT0! [You can also use other interrupts, see section + * "Optional MCU Description" below, or you can connect D- to the interrupt, as + * it is required if you use the USB_COUNT_SOF feature. If you use D- for the + * interrupt, the USB interrupt will also be triggered at Start-Of-Frame + * markers every millisecond.] + */ +#define USB_CFG_CLOCK_KHZ (F_CPU/1000) +/* Clock rate of the AVR in kHz. Legal values are 12000, 12800, 15000, 16000, + * 16500, 18000 and 20000. The 12.8 MHz and 16.5 MHz versions of the code + * require no crystal, they tolerate +/- 1% deviation from the nominal + * frequency. All other rates require a precision of 2000 ppm and thus a + * crystal! + * Since F_CPU should be defined to your actual clock rate anyway, you should + * not need to modify this setting. + */ +#define USB_CFG_CHECK_CRC 0 +/* Define this to 1 if you want that the driver checks integrity of incoming + * data packets (CRC checks). CRC checks cost quite a bit of code size and are + * currently only available for 18 MHz crystal clock. You must choose + * USB_CFG_CLOCK_KHZ = 18000 if you enable this option. + */ + +/* ----------------------- Optional Hardware Config ------------------------ */ + +/* #define USB_CFG_PULLUP_IOPORTNAME D */ +/* If you connect the 1.5k pullup resistor from D- to a port pin instead of + * V+, you can connect and disconnect the device from firmware by calling + * the macros usbDeviceConnect() and usbDeviceDisconnect() (see usbdrv.h). + * This constant defines the port on which the pullup resistor is connected. + */ +/* #define USB_CFG_PULLUP_BIT 4 */ +/* This constant defines the bit number in USB_CFG_PULLUP_IOPORT (defined + * above) where the 1.5k pullup resistor is connected. See description + * above for details. + */ + +/* --------------------------- Functional Range ---------------------------- */ + +#define USB_CFG_HAVE_INTRIN_ENDPOINT 1 +/* Define this to 1 if you want to compile a version with two endpoints: The + * default control endpoint 0 and an interrupt-in endpoint (any other endpoint + * number). + */ +#define USB_CFG_HAVE_INTRIN_ENDPOINT3 1 +/* Define this to 1 if you want to compile a version with three endpoints: The + * default control endpoint 0, an interrupt-in endpoint 3 (or the number + * configured below) and a catch-all default interrupt-in endpoint as above. + * You must also define USB_CFG_HAVE_INTRIN_ENDPOINT to 1 for this feature. + */ +#define USB_CFG_EP3_NUMBER 3 +/* If the so-called endpoint 3 is used, it can now be configured to any other + * endpoint number (except 0) with this macro. Default if undefined is 3. + */ +/* #define USB_INITIAL_DATATOKEN USBPID_DATA1 */ +/* The above macro defines the startup condition for data toggling on the + * interrupt/bulk endpoints 1 and 3. Defaults to USBPID_DATA1. + * Since the token is toggled BEFORE sending any data, the first packet is + * sent with the oposite value of this configuration! + */ +#define USB_CFG_IMPLEMENT_HALT 0 +/* Define this to 1 if you also want to implement the ENDPOINT_HALT feature + * for endpoint 1 (interrupt endpoint). Although you may not need this feature, + * it is required by the standard. We have made it a config option because it + * bloats the code considerably. + */ +#define USB_CFG_SUPPRESS_INTR_CODE 0 +/* Define this to 1 if you want to declare interrupt-in endpoints, but don't + * want to send any data over them. If this macro is defined to 1, functions + * usbSetInterrupt() and usbSetInterrupt3() are omitted. This is useful if + * you need the interrupt-in endpoints in order to comply to an interface + * (e.g. HID), but never want to send any data. This option saves a couple + * of bytes in flash memory and the transmit buffers in RAM. + */ +#define USB_CFG_INTR_POLL_INTERVAL 1 +/* If you compile a version with endpoint 1 (interrupt-in), this is the poll + * interval. The value is in milliseconds and must not be less than 10 ms for + * low speed devices. + */ +#define USB_CFG_IS_SELF_POWERED 0 +/* Define this to 1 if the device has its own power supply. Set it to 0 if the + * device is powered from the USB bus. + */ +// max power draw with maxed white underglow measured at 120 mA (peaks) +#define USB_CFG_MAX_BUS_POWER 100 +/* Set this variable to the maximum USB bus power consumption of your device. + * The value is in milliamperes. [It will be divided by two since USB + * communicates power requirements in units of 2 mA.] + */ +#define USB_CFG_IMPLEMENT_FN_WRITE 1 +/* Set this to 1 if you want usbFunctionWrite() to be called for control-out + * transfers. Set it to 0 if you don't need it and want to save a couple of + * bytes. + */ +#define USB_CFG_IMPLEMENT_FN_READ 0 +/* Set this to 1 if you need to send control replies which are generated + * "on the fly" when usbFunctionRead() is called. If you only want to send + * data from a static buffer, set it to 0 and return the data from + * usbFunctionSetup(). This saves a couple of bytes. + */ +#define USB_CFG_IMPLEMENT_FN_WRITEOUT 0 +/* Define this to 1 if you want to use interrupt-out (or bulk out) endpoints. + * You must implement the function usbFunctionWriteOut() which receives all + * interrupt/bulk data sent to any endpoint other than 0. The endpoint number + * can be found in 'usbRxToken'. + */ +#define USB_CFG_HAVE_FLOWCONTROL 0 +/* Define this to 1 if you want flowcontrol over USB data. See the definition + * of the macros usbDisableAllRequests() and usbEnableAllRequests() in + * usbdrv.h. + */ +#define USB_CFG_DRIVER_FLASH_PAGE 0 +/* If the device has more than 64 kBytes of flash, define this to the 64 k page + * where the driver's constants (descriptors) are located. Or in other words: + * Define this to 1 for boot loaders on the ATMega128. + */ +#define USB_CFG_LONG_TRANSFERS 0 +/* Define this to 1 if you want to send/receive blocks of more than 254 bytes + * in a single control-in or control-out transfer. Note that the capability + * for long transfers increases the driver size. + */ +/* #define USB_RX_USER_HOOK(data, len) if(usbRxToken == (uchar)USBPID_SETUP) blinkLED(); */ +/* This macro is a hook if you want to do unconventional things. If it is + * defined, it's inserted at the beginning of received message processing. + * If you eat the received message and don't want default processing to + * proceed, do a return after doing your things. One possible application + * (besides debugging) is to flash a status LED on each packet. + */ +/* #define USB_RESET_HOOK(resetStarts) if(!resetStarts){hadUsbReset();} */ +/* This macro is a hook if you need to know when an USB RESET occurs. It has + * one parameter which distinguishes between the start of RESET state and its + * end. + */ +/* #define USB_SET_ADDRESS_HOOK() hadAddressAssigned(); */ +/* This macro (if defined) is executed when a USB SET_ADDRESS request was + * received. + */ +#define USB_COUNT_SOF 0 +/* define this macro to 1 if you need the global variable "usbSofCount" which + * counts SOF packets. This feature requires that the hardware interrupt is + * connected to D- instead of D+. + */ +/* #ifdef __ASSEMBLER__ + * macro myAssemblerMacro + * in YL, TCNT0 + * sts timer0Snapshot, YL + * endm + * #endif + * #define USB_SOF_HOOK myAssemblerMacro + * This macro (if defined) is executed in the assembler module when a + * Start Of Frame condition is detected. It is recommended to define it to + * the name of an assembler macro which is defined here as well so that more + * than one assembler instruction can be used. The macro may use the register + * YL and modify SREG. If it lasts longer than a couple of cycles, USB messages + * immediately after an SOF pulse may be lost and must be retried by the host. + * What can you do with this hook? Since the SOF signal occurs exactly every + * 1 ms (unless the host is in sleep mode), you can use it to tune OSCCAL in + * designs running on the internal RC oscillator. + * Please note that Start Of Frame detection works only if D- is wired to the + * interrupt, not D+. THIS IS DIFFERENT THAN MOST EXAMPLES! + */ +#define USB_CFG_CHECK_DATA_TOGGLING 0 +/* define this macro to 1 if you want to filter out duplicate data packets + * sent by the host. Duplicates occur only as a consequence of communication + * errors, when the host does not receive an ACK. Please note that you need to + * implement the filtering yourself in usbFunctionWriteOut() and + * usbFunctionWrite(). Use the global usbCurrentDataToken and a static variable + * for each control- and out-endpoint to check for duplicate packets. + */ +#define USB_CFG_HAVE_MEASURE_FRAME_LENGTH 0 +/* define this macro to 1 if you want the function usbMeasureFrameLength() + * compiled in. This function can be used to calibrate the AVR's RC oscillator. + */ +#define USB_USE_FAST_CRC 0 +/* The assembler module has two implementations for the CRC algorithm. One is + * faster, the other is smaller. This CRC routine is only used for transmitted + * messages where timing is not critical. The faster routine needs 31 cycles + * per byte while the smaller one needs 61 to 69 cycles. The faster routine + * may be worth the 32 bytes bigger code size if you transmit lots of data and + * run the AVR close to its limit. + */ + +/* -------------------------- Device Description --------------------------- */ + +#define USB_CFG_VENDOR_ID (VENDOR_ID & 0xFF), ((VENDOR_ID >> 8) & 0xFF) +/* USB vendor ID for the device, low byte first. If you have registered your + * own Vendor ID, define it here. Otherwise you may use one of obdev's free + * shared VID/PID pairs. Be sure to read USB-IDs-for-free.txt for rules! + * *** IMPORTANT NOTE *** + * This template uses obdev's shared VID/PID pair for Vendor Class devices + * with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand + * the implications! + */ +#define USB_CFG_DEVICE_ID (PRODUCT_ID & 0xFF), ((PRODUCT_ID >> 8) & 0xFF) +/* This is the ID of the product, low byte first. It is interpreted in the + * scope of the vendor ID. If you have registered your own VID with usb.org + * or if you have licensed a PID from somebody else, define it here. Otherwise + * you may use one of obdev's free shared VID/PID pairs. See the file + * USB-IDs-for-free.txt for details! + * *** IMPORTANT NOTE *** + * This template uses obdev's shared VID/PID pair for Vendor Class devices + * with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand + * the implications! + */ +#define USB_CFG_DEVICE_VERSION 0x00, 0x01 +/* Version number of the device: Minor number first, then major number. + */ +#define USB_CFG_VENDOR_NAME 'H','n','a','h','K','B' +#define USB_CFG_VENDOR_NAME_LEN 6 +/* These two values define the vendor name returned by the USB device. The name + * must be given as a list of characters under single quotes. The characters + * are interpreted as Unicode (UTF-16) entities. + * If you don't want a vendor name string, undefine these macros. + * ALWAYS define a vendor name containing your Internet domain name if you use + * obdev's free shared VID/PID pair. See the file USB-IDs-for-free.txt for + * details. + */ +#define USB_CFG_DEVICE_NAME 'H', 'n', 'a', 'h', '4', '0' +#define USB_CFG_DEVICE_NAME_LEN 6 +/* Same as above for the device name. If you don't want a device name, undefine + * the macros. See the file USB-IDs-for-free.txt before you assign a name if + * you use a shared VID/PID. + */ +#define USB_CFG_SERIAL_NUMBER 'H','n','a','h','K','B' +#define USB_CFG_SERIAL_NUMBER_LEN 6 +/* Same as above for the serial number. If you don't want a serial number, + * undefine the macros. + * It may be useful to provide the serial number through other means than at + * compile time. See the section about descriptor properties below for how + * to fine tune control over USB descriptors such as the string descriptor + * for the serial number. + */ +#define USB_CFG_DEVICE_CLASS 0 +#define USB_CFG_DEVICE_SUBCLASS 0 +/* See USB specification if you want to conform to an existing device class. + * Class 0xff is "vendor specific". + */ +#define USB_CFG_INTERFACE_CLASS 3 /* HID */ +#define USB_CFG_INTERFACE_SUBCLASS 1 /* Boot */ +#define USB_CFG_INTERFACE_PROTOCOL 1 /* Keyboard */ +/* See USB specification if you want to conform to an existing device class or + * protocol. The following classes must be set at interface level: + * HID class is 3, no subclass and protocol required (but may be useful!) + * CDC class is 2, use subclass 2 and protocol 1 for ACM + */ +#define USB_CFG_HID_REPORT_DESCRIPTOR_LENGTH 0 +/* Define this to the length of the HID report descriptor, if you implement + * an HID device. Otherwise don't define it or define it to 0. + * If you use this define, you must add a PROGMEM character array named + * "usbHidReportDescriptor" to your code which contains the report descriptor. + * Don't forget to keep the array and this define in sync! + */ + +/* #define USB_PUBLIC static */ +/* Use the define above if you #include usbdrv.c instead of linking against it. + * This technique saves a couple of bytes in flash memory. + */ + +/* ------------------- Fine Control over USB Descriptors ------------------- */ +/* If you don't want to use the driver's default USB descriptors, you can + * provide our own. These can be provided as (1) fixed length static data in + * flash memory, (2) fixed length static data in RAM or (3) dynamically at + * runtime in the function usbFunctionDescriptor(). See usbdrv.h for more + * information about this function. + * Descriptor handling is configured through the descriptor's properties. If + * no properties are defined or if they are 0, the default descriptor is used. + * Possible properties are: + * + USB_PROP_IS_DYNAMIC: The data for the descriptor should be fetched + * at runtime via usbFunctionDescriptor(). If the usbMsgPtr mechanism is + * used, the data is in FLASH by default. Add property USB_PROP_IS_RAM if + * you want RAM pointers. + * + USB_PROP_IS_RAM: The data returned by usbFunctionDescriptor() or found + * in static memory is in RAM, not in flash memory. + * + USB_PROP_LENGTH(len): If the data is in static memory (RAM or flash), + * the driver must know the descriptor's length. The descriptor itself is + * found at the address of a well known identifier (see below). + * List of static descriptor names (must be declared PROGMEM if in flash): + * char usbDescriptorDevice[]; + * char usbDescriptorConfiguration[]; + * char usbDescriptorHidReport[]; + * char usbDescriptorString0[]; + * int usbDescriptorStringVendor[]; + * int usbDescriptorStringDevice[]; + * int usbDescriptorStringSerialNumber[]; + * Other descriptors can't be provided statically, they must be provided + * dynamically at runtime. + * + * Descriptor properties are or-ed or added together, e.g.: + * #define USB_CFG_DESCR_PROPS_DEVICE (USB_PROP_IS_RAM | USB_PROP_LENGTH(18)) + * + * The following descriptors are defined: + * USB_CFG_DESCR_PROPS_DEVICE + * USB_CFG_DESCR_PROPS_CONFIGURATION + * USB_CFG_DESCR_PROPS_STRINGS + * USB_CFG_DESCR_PROPS_STRING_0 + * USB_CFG_DESCR_PROPS_STRING_VENDOR + * USB_CFG_DESCR_PROPS_STRING_PRODUCT + * USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER + * USB_CFG_DESCR_PROPS_HID + * USB_CFG_DESCR_PROPS_HID_REPORT + * USB_CFG_DESCR_PROPS_UNKNOWN (for all descriptors not handled by the driver) + * + * Note about string descriptors: String descriptors are not just strings, they + * are Unicode strings prefixed with a 2 byte header. Example: + * int serialNumberDescriptor[] = { + * USB_STRING_DESCRIPTOR_HEADER(6), + * 'S', 'e', 'r', 'i', 'a', 'l' + * }; + */ + +#define USB_CFG_DESCR_PROPS_DEVICE 0 +#define USB_CFG_DESCR_PROPS_CONFIGURATION USB_PROP_IS_DYNAMIC +//#define USB_CFG_DESCR_PROPS_CONFIGURATION 0 +#define USB_CFG_DESCR_PROPS_STRINGS 0 +#define USB_CFG_DESCR_PROPS_STRING_0 0 +#define USB_CFG_DESCR_PROPS_STRING_VENDOR 0 +#define USB_CFG_DESCR_PROPS_STRING_PRODUCT 0 +#define USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER 0 +#define USB_CFG_DESCR_PROPS_HID USB_PROP_IS_DYNAMIC +//#define USB_CFG_DESCR_PROPS_HID 0 +#define USB_CFG_DESCR_PROPS_HID_REPORT USB_PROP_IS_DYNAMIC +//#define USB_CFG_DESCR_PROPS_HID_REPORT 0 +#define USB_CFG_DESCR_PROPS_UNKNOWN 0 + +#define usbMsgPtr_t unsigned short +/* If usbMsgPtr_t is not defined, it defaults to 'uchar *'. We define it to + * a scalar type here because gcc generates slightly shorter code for scalar + * arithmetics than for pointer arithmetics. Remove this define for backward + * type compatibility or define it to an 8 bit type if you use data in RAM only + * and all RAM is below 256 bytes (tiny memory model in IAR CC). + */ + +/* ----------------------- Optional MCU Description ------------------------ */ + +/* The following configurations have working defaults in usbdrv.h. You + * usually don't need to set them explicitly. Only if you want to run + * the driver on a device which is not yet supported or with a compiler + * which is not fully supported (such as IAR C) or if you use a differnt + * interrupt than INT0, you may have to define some of these. + */ +/* #define USB_INTR_CFG MCUCR */ +/* #define USB_INTR_CFG_SET ((1 << ISC00) | (1 << ISC01)) */ +/* #define USB_INTR_CFG_CLR 0 */ +/* #define USB_INTR_ENABLE GIMSK */ +/* #define USB_INTR_ENABLE_BIT INT0 */ +/* #define USB_INTR_PENDING GIFR */ +/* #define USB_INTR_PENDING_BIT INTF0 */ +/* #define USB_INTR_VECTOR INT0_vect */ + +/* Set INT1 for D- falling edge to count SOF */ +/* #define USB_INTR_CFG EICRA */ +// #define USB_INTR_CFG_SET ((1 << ISC11) | (0 << ISC10)) +// /* #define USB_INTR_CFG_CLR 0 */ +// /* #define USB_INTR_ENABLE EIMSK */ +// #define USB_INTR_ENABLE_BIT INT1 +// /* #define USB_INTR_PENDING EIFR */ +// #define USB_INTR_PENDING_BIT INTF1 +// #define USB_INTR_VECTOR INT1_vect + +#endif /* __usbconfig_h_included__ */ diff --git a/keyboards/handwired/ibm122m/config.h b/keyboards/handwired/ibm122m/config.h index 1ef7be78d..8189f704d 100644 --- a/keyboards/handwired/ibm122m/config.h +++ b/keyboards/handwired/ibm122m/config.h @@ -53,7 +53,7 @@ along with this program. If not, see <http://www.gnu.org/licenses/>. // #define BACKLIGHT_LEVELS 3 /* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */ -#define DEBOUNCING_DELAY 15 +#define DEBOUNCE 15 /* define if matrix has ghost (lacks anti-ghosting diodes) */ //#define MATRIX_HAS_GHOST diff --git a/keyboards/handwired/jn68m/config.h b/keyboards/handwired/jn68m/config.h index f6ab4056b..ef0c09cf1 100644 --- a/keyboards/handwired/jn68m/config.h +++ b/keyboards/handwired/jn68m/config.h @@ -40,7 +40,7 @@ along with this program. If not, see <http://www.gnu.org/licenses/>. #define DIODE_DIRECTION COL2ROW /* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */ -#define DEBOUNCING_DELAY 5 +#define DEBOUNCE 5 /* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ #define LOCKING_SUPPORT_ENABLE diff --git a/keyboards/handwired/jopr/config.h b/keyboards/handwired/jopr/config.h new file mode 100644 index 000000000..aece70915 --- /dev/null +++ b/keyboards/handwired/jopr/config.h @@ -0,0 +1,49 @@ +#pragma once + +#include "config_common.h" + +/* USB Device descriptor parameter */ +#define VENDOR_ID 0x4DAE +#define PRODUCT_ID 0x1000 +#define DEVICE_VER 0x0001 +#define MANUFACTURER joelproko +#define PRODUCT jopr-106-Nl2SR-Cl2nL +#define DESCRIPTION jopr-106 Mechanical Keyboard + +/* key matrix size */ +#define MATRIX_ROWS 10 +#define MATRIX_COLS 11 + +/* key matrix pins */ +#define MATRIX_ROW_PINS { D0, D6, D2, D4, D3, D5, D7, C6, B6, F5 } +#define MATRIX_COL_PINS { B3, B2, B1, B0, F7, E6, F6, B5, C7, B4, D1 } +#define UNUSED_PINS { B7 } + +/* COL2ROW or ROW2COL */ +#define DIODE_DIRECTION COL2ROW + +/* number of backlight levels */ +#ifdef BACKLIGHT_PIN +#define BACKLIGHT_LEVELS 0 +#endif + +/* Set 0 if debouncing isn't needed */ +#define DEBOUNCE 5 + +/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ +/* #define LOCKING_SUPPORT_ENABLE */ + +/* Locking resynchronize hack */ +#define LOCKING_RESYNC_ENABLE +/* #define IS_COMMAND() (get_mods() == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT))) */ +#define NO_ACTION_ONESHOT +#define TAPPING_TOGGLE 3 + +/*#define RGB_DI_PIN F4*/ +#ifdef RGB_DI_PIN +/*#define RGBLIGHT_ANIMATIONS*/ +#define RGBLED_NUM 1 +#define RGBLIGHT_HUE_STEP 1 +#define RGBLIGHT_SAT_STEP 1 +#define RGBLIGHT_VAL_STEP 1 +#endif diff --git a/keyboards/handwired/jopr/info.json b/keyboards/handwired/jopr/info.json new file mode 100644 index 000000000..c4cadb8c3 --- /dev/null +++ b/keyboards/handwired/jopr/info.json @@ -0,0 +1,562 @@ +{ + "keyboard_name": "jopr-106", + "url": "https://github.com/joelproko/keyboard_layout_jopr", + "maintainer": "joelproko", + "width": 22.5, + "height": 6.25, + "layouts": { + "LAYOUT": { + "key_count": 106, + "layout": [ + { + "label": "MX_A0", + "x": 0, + "y": 0 + }, + { + "label": "MX_B0", + "x": 1.25, + "y": 0 + }, + { + "label": "MX_C0", + "x": 2.25, + "y": 0 + }, + { + "label": "MX_D0", + "x": 3.25, + "y": 0 + }, + { + "label": "MX_E0", + "x": 4.25, + "y": 0 + }, + { + "label": "MX_F0", + "x": 5.5, + "y": 0 + }, + { + "label": "MX_G0", + "x": 6.5, + "y": 0 + }, + { + "label": "MX_H0", + "x": 7.5, + "y": 0 + }, + { + "label": "MX_I0", + "x": 8.5, + "y": 0 + }, + { + "label": "MX_J0", + "x": 9.75, + "y": 0 + }, + { + "label": "MX_A6", + "x": 10.75, + "y": 0 + }, + { + "label": "MX_B6", + "x": 11.75, + "y": 0 + }, + { + "label": "MX_C6", + "x": 12.75, + "y": 0 + }, + { + "label": "MX_D6", + "x": 14, + "y": 0 + }, + { + "label": "MX_E6", + "x": 15.25, + "y": 0 + }, + { + "label": "MX_F6", + "x": 16.25, + "y": 0 + }, + { + "label": "MX_G6", + "x": 17.25, + "y": 0 + }, + { + "label": "MX_H6", + "x": 18.25, + "y": 0 + }, + { + "label": "MX_A1", + "x": 0, + "y": 1.25 + }, + { + "label": "MX_B1", + "x": 1, + "y": 1.25 + }, + { + "label": "MX_C1", + "x": 2, + "y": 1.25 + }, + { + "label": "MX_D1", + "x": 3, + "y": 1.25 + }, + { + "label": "MX_E1", + "x": 4, + "y": 1.25 + }, + { + "label": "MX_F1", + "x": 5, + "y": 1.25 + }, + { + "label": "MX_G1", + "x": 6, + "y": 1.25 + }, + { + "label": "MX_H1", + "x": 7, + "y": 1.25 + }, + { + "label": "MX_I1", + "x": 8, + "y": 1.25 + }, + { + "label": "MX_J1", + "x": 9, + "y": 1.25 + }, + { + "label": "MX_A7", + "x": 10, + "y": 1.25 + }, + { + "label": "MX_B7", + "x": 11, + "y": 1.25 + }, + { + "label": "MX_C7", + "x": 12, + "y": 1.25 + }, + { + "label": "MX_D7", + "x": 13, + "y": 1.25, + "w": 2 + }, + { + "label": "MX_E7", + "x": 15.25, + "y": 1.25 + }, + { + "label": "MX_F7", + "x": 16.25, + "y": 1.25 + }, + { + "label": "MX_G7", + "x": 17.25, + "y": 1.25 + }, + { + "label": "MX_H7", + "x": 18.25, + "y": 1.25 + }, + { + "label": "MX_A2", + "x": 0, + "y": 2.25, + "w": 1.5 + }, + { + "label": "MX_B2", + "x": 1.5, + "y": 2.25 + }, + { + "label": "MX_C2", + "x": 2.5, + "y": 2.25 + }, + { + "label": "MX_D2", + "x": 3.5, + "y": 2.25 + }, + { + "label": "MX_E2", + "x": 4.5, + "y": 2.25 + }, + { + "label": "MX_F2", + "x": 5.5, + "y": 2.25 + }, + { + "label": "MX_G2", + "x": 6.5, + "y": 2.25 + }, + { + "label": "MX_H2", + "x": 7.5, + "y": 2.25 + }, + { + "label": "MX_I2", + "x": 8.5, + "y": 2.25 + }, + { + "label": "MX_J2", + "x": 9.5, + "y": 2.25 + }, + { + "label": "MX_A8", + "x": 10.5, + "y": 2.25 + }, + { + "label": "MX_B8", + "x": 11.5, + "y": 2.25 + }, + { + "label": "MX_C8", + "x": 12.5, + "y": 2.25 + }, + { + "label": "MX_D8", + "x": 13.75, + "y": 2.25, + "w": 1.25, + "h": 2 + }, + { + "label": "MX_E8", + "x": 15.25, + "y": 2.25 + }, + { + "label": "MX_F8", + "x": 16.25, + "y": 2.25 + }, + { + "label": "MX_G8", + "x": 17.25, + "y": 2.25 + }, + { + "label": "MX_H8", + "x": 18.25, + "y": 2.25, + "h": 2 + }, + { + "label": "MX_A3", + "x": 0, + "y": 3.25, + "w": 1.75 + }, + { + "label": "MX_B3", + "x": 1.75, + "y": 3.25 + }, + { + "label": "MX_C3", + "x": 2.75, + "y": 3.25 + }, + { + "label": "MX_D3", + "x": 3.75, + "y": 3.25 + }, + { + "label": "MX_E3", + "x": 4.75, + "y": 3.25 + }, + { + "label": "MX_F3", + "x": 5.75, + "y": 3.25 + }, + { + "label": "MX_G3", + "x": 6.75, + "y": 3.25 + }, + { + "label": "MX_H3", + "x": 7.75, + "y": 3.25 + }, + { + "label": "MX_I3", + "x": 8.75, + "y": 3.25 + }, + { + "label": "MX_J3", + "x": 9.75, + "y": 3.25 + }, + { + "label": "MX_A9", + "x": 10.75, + "y": 3.25 + }, + { + "label": "MX_B9", + "x": 11.75, + "y": 3.25 + }, + { + "label": "MX_C9", + "x": 12.75, + "y": 3.25 + }, + { + "label": "MX_E9", + "x": 15.25, + "y": 3.25 + }, + { + "label": "MX_F9", + "x": 16.25, + "y": 3.25 + }, + { + "label": "MX_G9", + "x": 17.25, + "y": 3.25 + }, + { + "label": "MX_H9", + "x": 19.5, + "y": 3.25 + }, + { + "label": "MX_K1", + "x": 20.5, + "y": 3.25 + }, + { + "label": "MX_K0", + "x": 21.5, + "y": 3.25 + }, + { + "label": "MX_A4", + "x": 0, + "y": 4.25, + "w": 1.25 + }, + { + "label": "MX_B4", + "x": 1.25, + "y": 4.25 + }, + { + "label": "MX_C4", + "x": 2.25, + "y": 4.25 + }, + { + "label": "MX_D4", + "x": 3.25, + "y": 4.25 + }, + { + "label": "MX_E4", + "x": 4.25, + "y": 4.25 + }, + { + "label": "MX_F4", + "x": 5.25, + "y": 4.25 + }, + { + "label": "MX_G4", + "x": 6.25, + "y": 4.25 + }, + { + "label": "MX_H4", + "x": 7.25, + "y": 4.25 + }, + { + "label": "MX_I4", + "x": 8.25, + "y": 4.25 + }, + { + "label": "MX_J4", + "x": 9.25, + "y": 4.25 + }, + { + "label": "MX_I9", + "x": 10.25, + "y": 4.25 + }, + { + "label": "MX_I8", + "x": 11.25, + "y": 4.25 + }, + { + "label": "MX_I7", + "x": 12.25, + "y": 4.25, + "w": 2.75 + }, + { + "label": "MX_I6", + "x": 15.25, + "y": 4.25 + }, + { + "label": "MX_J9", + "x": 16.25, + "y": 4.25 + }, + { + "label": "MX_J8", + "x": 17.25, + "y": 4.25 + }, + { + "label": "MX_J7", + "x": 18.25, + "y": 4.25, + "h": 2 + }, + { + "label": "MX_J6", + "x": 19.5, + "y": 4.25 + }, + { + "label": "MX_K3", + "x": 20.5, + "y": 4.25 + }, + { + "label": "MX_K2", + "x": 21.5, + "y": 4.25 + }, + { + "label": "MX_A5", + "x": 0, + "y": 5.25, + "w": 1.25 + }, + { + "label": "MX_B5", + "x": 1.25, + "y": 5.25, + "w": 1.25 + }, + { + "label": "MX_C5", + "x": 2.5, + "y": 5.25, + "w": 1.25 + }, + { + "label": "MX_D5", + "x": 3.75, + "y": 5.25, + "w": 6.25 + }, + { + "label": "MX_J5", + "x": 10, + "y": 5.25, + "w": 1.25 + }, + { + "label": "MX_I5", + "x": 11.25, + "y": 5.25, + "w": 1.25 + }, + { + "label": "MX_K9", + "x": 12.5, + "y": 5.25, + "w": 1.25 + }, + { + "label": "MX_E5", + "x": 13.75, + "y": 5.25, + "w": 1.25 + }, + { + "label": "MX_K8", + "x": 15.25, + "y": 5.25, + "w": 2 + }, + { + "label": "MX_K7", + "x": 17.25, + "y": 5.25 + }, + { + "label": "MX_K6", + "x": 19.5, + "y": 5.25 + }, + { + "label": "MX_K5", + "x": 20.5, + "y": 5.25 + }, + { + "label": "MX_K4", + "x": 21.5, + "y": 5.25 + } + ] + } + } +} diff --git a/keyboards/handwired/jopr/jopr.c b/keyboards/handwired/jopr/jopr.c new file mode 100644 index 000000000..3dccb719c --- /dev/null +++ b/keyboards/handwired/jopr/jopr.c @@ -0,0 +1,11 @@ +#include "jopr.h" +void matrix_init_kb(void) { + matrix_init_user(); + led_init_ports(); +}; + +void led_init_ports(void) { + setPinOutput(F0); + setPinOutput(F1); + setPinOutput(F4); +}
\ No newline at end of file diff --git a/keyboards/handwired/jopr/jopr.h b/keyboards/handwired/jopr/jopr.h new file mode 100644 index 000000000..b79a8f264 --- /dev/null +++ b/keyboards/handwired/jopr/jopr.h @@ -0,0 +1,24 @@ +#pragma once + +#include "quantum.h" + +#define LAYOUT( \ + K000, K001, K002, K003, K004, K005, K006, K007, K008, K009, K600, K601, K602, K603, K604, K605, K606, K607, \ + K100, K101, K102, K103, K104, K105, K106, K107, K108, K109, K700, K701, K702, K703, K704, K705, K706, K707, \ + K200, K201, K202, K203, K204, K205, K206, K207, K208, K209, K800, K801, K802, K803, K804, K805, K806, K807, \ + K300, K301, K302, K303, K304, K305, K306, K307, K308, K309, K900, K901, K902, K904, K905, K906, K907, K110, K010, \ + K400, K401, K402, K403, K404, K405, K406, K407, K408, K409, K908, K808, K708, K608, K909, K809, K709, K609, K310, K210, \ + K500, K501, K502, K503, K509, K508, K910, K504, K810, K710, K610, K510, K410 \ +) \ +{ \ + { K000, K001, K002, K003, K004, K005, K006, K007, K008, K009, K010 }, \ + { K100, K101, K102, K103, K104, K105, K106, K107, K108, K109, K110 }, \ + { K200, K201, K202, K203, K204, K205, K206, K207, K208, K209, K210 }, \ + { K300, K301, K302, K303, K304, K305, K306, K307, K308, K309, K310 }, \ + { K400, K401, K402, K403, K404, K405, K406, K407, K408, K409, K410 }, \ + { K500, K501, K502, K503, K504, KC_NO, KC_NO, KC_NO, K508, K509, K510 }, \ + { K600, K601, K602, K603, K604, K605, K606, K607, K608, K609, K610 }, \ + { K700, K701, K702, K703, K704, K705, K706, K707, K708, K709, K710 }, \ + { K800, K801, K802, K803, K804, K805, K806, K807, K808, K809, K810 }, \ + { K900, K901, K902, KC_NO, K904, K905, K906, K907, K908, K909, K910 } \ +} diff --git a/keyboards/handwired/jopr/keymaps/default/keymap.c b/keyboards/handwired/jopr/keymaps/default/keymap.c new file mode 100644 index 000000000..d6b998f49 --- /dev/null +++ b/keyboards/handwired/jopr/keymaps/default/keymap.c @@ -0,0 +1,59 @@ +#include QMK_KEYBOARD_H + +#define _BL 0 +#define _FN 1 +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { + + [_BL] = LAYOUT( + KC_ESC, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, KC_DEL, KC_NO, KC_CAPS, KC_SLCK, KC_PAUS, + KC_GRV, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_EQL, KC_BSPC, KC_PSCR, KC_PSLS, KC_PAST, KC_PMNS, + KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_LBRC, KC_RBRC, KC_ENT, KC_P7, KC_P8, KC_P9, KC_PPLS, + KC_MHEN, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT, KC_NUHS, KC_P4, KC_P5, KC_P6, KC_PGUP, KC_INS, KC_PGDN, + KC_LSFT, KC_NUBS, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, KC_RSFT, KC_P1, KC_P2, KC_P3, KC_PENT, KC_HOME, KC_UP, KC_END, + KC_LCTL, KC_LWIN, KC_LALT, KC_SPC, KC_RALT, KC_RWIN, LT(_FN,KC_APP), KC_RCTL, KC_P0, KC_PDOT, KC_LEFT, KC_DOWN, KC_RGHT + ), + [_FN] = LAYOUT( + _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, KC_SYSREQ, _______, _______, _______, + _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, + _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, KC_MSTP, KC_VOLU, _______, _______, + _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, KC_MPRV, KC_MPLY, KC_MNXT, _______, KC_MUTE, _______, + _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, KC_MUTE, KC_VOLD, _______, _______, KC_VOLD, KC_MSTP, KC_VOLU, + _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, KC_MPRV, KC_MPLY, KC_MNXT + ) +}; + +void led_set_user(uint8_t usb_led) { + + if (IS_LED_ON(usb_led, USB_LED_CAPS_LOCK)) { + writePinHigh(F1); + } else { + writePinLow(F1); + } + + if (IS_LED_ON(usb_led, USB_LED_SCROLL_LOCK)) { + writePinHigh(F0); + } else { + writePinLow(F0); + } + + if (!(IS_LED_ON(usb_led, USB_LED_NUM_LOCK))) { + tap_code(KC_NUMLOCK); + } +} +bool process_record_user(uint16_t keycode, keyrecord_t *record) { + static bool sysreq_led = false; + if (record->event.pressed) { + if (sysreq_led) { + sysreq_led = false; + writePinLow(F4); + } + else { + switch(keycode) { + case KC_SYSREQ: + sysreq_led = true; + writePinHigh(F4); + } + } + } + return true; +} diff --git a/keyboards/handwired/jopr/keymaps/modded_white/keymap.c b/keyboards/handwired/jopr/keymaps/modded_white/keymap.c new file mode 100644 index 000000000..da1f9e183 --- /dev/null +++ b/keyboards/handwired/jopr/keymaps/modded_white/keymap.c @@ -0,0 +1,59 @@ +#include QMK_KEYBOARD_H + +#define _BL 0 +#define _FN 1 +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { + + [_BL] = LAYOUT( + KC_ESC, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, KC_DEL, KC_NO, KC_CAPS, KC_SLCK, KC_PAUS, + KC_NUHS, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_NUBS, KC_SLSH, KC_BSPC, KC_PSCR, KC_PSLS, KC_PAST, KC_PMNS, + KC_TAB, KC_V, KC_Y, KC_D, KC_COMM, KC_QUOT, KC_INT1, KC_J, KC_M, KC_L, KC_U, KC_LBRC, KC_RBRC, KC_ENT, KC_P7, KC_P8, KC_P9, KC_PPLS, + KC_MHEN, KC_A, KC_T, KC_H, KC_E, KC_B, KC_MINS, KC_C, KC_S, KC_N, KC_O, KC_I, KC_EQL, KC_P4, KC_P5, KC_P6, KC_PGUP, KC_INS, KC_PGDN, + KC_LSFT, KC_GRV, KC_P, KC_K, KC_G, KC_W, KC_Q, KC_X, KC_R, KC_F, KC_DOT, KC_Z, KC_RSFT, KC_P1, KC_P2, KC_P3, KC_PENT, KC_HOME, KC_UP, KC_END, + KC_LCTL, KC_LWIN, KC_LALT, KC_SPC, KC_RALT, KC_RWIN, LT(_FN,KC_APP), KC_RCTL, KC_P0, KC_PDOT, KC_LEFT, KC_DOWN, KC_RGHT + ), + [_FN] = LAYOUT( + _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, KC_SYSREQ, _______, _______, _______, + _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, + _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, KC_MSTP, KC_VOLU, _______, _______, + _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, KC_MPRV, KC_MPLY, KC_MNXT, _______, KC_MUTE, _______, + _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, KC_MUTE, KC_VOLD, _______, _______, KC_VOLD, KC_MSTP, KC_VOLU, + _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, KC_MPRV, KC_MPLY, KC_MNXT + ) +}; + +void led_set_user(uint8_t usb_led) { + + if (IS_LED_ON(usb_led, USB_LED_CAPS_LOCK)) { + writePinHigh(F1); + } else { + writePinLow(F1); + } + + if (IS_LED_ON(usb_led, USB_LED_SCROLL_LOCK)) { + writePinHigh(F0); + } else { + writePinLow(F0); + } + + if (!(IS_LED_ON(usb_led, USB_LED_NUM_LOCK))) { + tap_code(KC_NUMLOCK); + } +} +bool process_record_user(uint16_t keycode, keyrecord_t *record) { + static bool sysreq_led = false; + if (record->event.pressed) { + if (sysreq_led) { + sysreq_led = false; + writePinLow(F4); + } + else { + switch(keycode) { + case KC_SYSREQ: + sysreq_led = true; + writePinHigh(F4); + } + } + } + return true; +}
\ No newline at end of file diff --git a/keyboards/handwired/jopr/readme.md b/keyboards/handwired/jopr/readme.md new file mode 100644 index 000000000..eab197d2d --- /dev/null +++ b/keyboards/handwired/jopr/readme.md @@ -0,0 +1,17 @@ +# jopr-106-Nl2SR-Cl2MH + +106-key based on ISO 105-key, NumLock to SysReq, CapsLock to Muhenkan/ROYA, NumLock state forced on + + + + +Inspired by [KeyBored](https://github.com/itractus/KeyBored) and [white_keyboard_layout](https://github.com/mw8/white_keyboard_layout) + +Keyboard Maintainer: [joelproko](https://github.com/joelproko) +Hardware: https://github.com/joelproko/keyboard_layout_jopr + +Make example for this keyboard (after setting up your build environment): + + make jopr:default + +See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs). diff --git a/keyboards/handwired/jopr/rules.mk b/keyboards/handwired/jopr/rules.mk new file mode 100644 index 000000000..de83252c3 --- /dev/null +++ b/keyboards/handwired/jopr/rules.mk @@ -0,0 +1,63 @@ +# MCU name +MCU = atmega32u4 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# atmega32a bootloadHID +BOOTLOADER = atmel-dfu + + +# Build Options +# comment out to disable the options. +# +BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE = no # Mouse keys(+4700) +EXTRAKEY_ENABLE = yes # Audio control and System control(+450) +CONSOLE_ENABLE = no # Console for debug(+400) +COMMAND_ENABLE = no # Commands for debug and configuration +SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend +NKRO_ENABLE = yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality +AUDIO_ENABLE = no +UNICODE_ENABLE = yes +RGBLIGHT_ENABLE = no diff --git a/keyboards/handwired/jot50/config.h b/keyboards/handwired/jot50/config.h index 2dfcfd2d2..2d2c1c183 100644 --- a/keyboards/handwired/jot50/config.h +++ b/keyboards/handwired/jot50/config.h @@ -29,7 +29,7 @@ #define DIODE_DIRECTION COL2ROW /* Set 0 if debouncing isn't needed */ -#define DEBOUNCING_DELAY 5 +#define DEBOUNCE 5 /* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ #define LOCKING_SUPPORT_ENABLE diff --git a/keyboards/handwired/jotanck/config.h b/keyboards/handwired/jotanck/config.h index 38b77586e..925464825 100644 --- a/keyboards/handwired/jotanck/config.h +++ b/keyboards/handwired/jotanck/config.h @@ -20,17 +20,15 @@ #define UNUSED_PINS /* leds */ -#define QMK_LED B4 -#define BACKLIGHT_LEVELS 3 -#define BACKLIGHT_PIN B5 -#define BACKLIGHT_BREATHING -#define BREATHING_PERIOD 5 +#define JOTANCK_LEDS +#define JOTANCK_LED1 B5 +#define JOTANCK_LED2 B4 /* COL2ROW or ROW2COL */ #define DIODE_DIRECTION COL2ROW /* Set 0 if debouncing isn't needed */ -#define DEBOUNCING_DELAY 5 +#define DEBOUNCE 5 /* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ #define LOCKING_SUPPORT_ENABLE diff --git a/keyboards/handwired/jotanck/jotanck.c b/keyboards/handwired/jotanck/jotanck.c index 7744570b2..812781c3b 100644 --- a/keyboards/handwired/jotanck/jotanck.c +++ b/keyboards/handwired/jotanck/jotanck.c @@ -1,6 +1,10 @@ #include "jotanck.h" void matrix_init_kb(void) { + matrix_init_user(); +} - matrix_init_user(); +void keyboard_pre_init_user() { + setPinOutput(JOTANCK_LED1); + setPinOutput(JOTANCK_LED2); } diff --git a/keyboards/handwired/jotanck/keymaps/default/keymap.c b/keyboards/handwired/jotanck/keymaps/default/keymap.c index 2e9f4a39f..3eb01a658 100644 --- a/keyboards/handwired/jotanck/keymaps/default/keymap.c +++ b/keyboards/handwired/jotanck/keymaps/default/keymap.c @@ -78,7 +78,7 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { [_ADJUST] = LAYOUT_ortho_4x12 ( _______, RESET, _______, _______, _______, _______, _______, _______, KC_PSCR, KC_SLCK, KC_PAUS, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, - _______, _______, _______, _______, _______, BL_STEP, BL_BRTG, _______, _______, _______, _______, _______, + _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______ ), }; diff --git a/keyboards/handwired/jotanck/readme.md b/keyboards/handwired/jotanck/readme.md index 28bbab86b..e9dd82403 100644 --- a/keyboards/handwired/jotanck/readme.md +++ b/keyboards/handwired/jotanck/readme.md @@ -20,10 +20,10 @@ Hardware Availability: [Mercado Libre](https://articulo.mercadolibre.com.ar/MLA- | Arduino pin | A3 | A2 | A1 | A0 | 15 | 14 | TX0 | RXI | 2 | 3 | 4 | 5 | | QMK pin | F4 | F5 | F6 | F7 | B1 | B3 | D3 | D2 | D1 | D0 | D4 | C6 | -| | QMK led | Backlight | -|-------------|-----------|-----------| -| Arduino pin | 8 | 9 | -| QMK pin | B4 | B5 | +| | LED1 | LED2 | +|-------------|------|------| +| Arduino pin | 9 | 8 | +| QMK pin | B5 | B4 | ### Compiling the Firmware diff --git a/keyboards/handwired/jotanck/rules.mk b/keyboards/handwired/jotanck/rules.mk index 6b39b7cc1..fa2881413 100644 --- a/keyboards/handwired/jotanck/rules.mk +++ b/keyboards/handwired/jotanck/rules.mk @@ -50,10 +50,10 @@ OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000) MOUSEKEY_ENABLE = yes # Mouse keys(+4700) EXTRAKEY_ENABLE = yes # Audio control and System control(+450) -CONSOLE_ENABLE = yes # Console for debug(+400) -COMMAND_ENABLE = no # Commands for debug and configuration -NKRO_ENABLE = yes # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work -BACKLIGHT_ENABLE = yes # Enable keyboard backlight functionality +CONSOLE_ENABLE = yes # Console for debug(+400) +COMMAND_ENABLE = no # Commands for debug and configuration +NKRO_ENABLE = yes # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality MIDI_ENABLE = no # MIDI controls AUDIO_ENABLE = no # Audio output on port C6 UNICODE_ENABLE = no # Unicode diff --git a/keyboards/handwired/jotpad16/config.h b/keyboards/handwired/jotpad16/config.h index e113597dc..075f9649c 100644 --- a/keyboards/handwired/jotpad16/config.h +++ b/keyboards/handwired/jotpad16/config.h @@ -28,11 +28,10 @@ #define DIODE_DIRECTION COL2ROW /* Set 0 if debouncing isn't needed */ -#define DEBOUNCING_DELAY 0 +#define DEBOUNCE 0 /* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ #define LOCKING_SUPPORT_ENABLE /* Locking resynchronize hack */ #define LOCKING_RESYNC_ENABLE - diff --git a/keyboards/handwired/kbod/config.h b/keyboards/handwired/kbod/config.h index 5f02c7172..f0bba68a5 100644 --- a/keyboards/handwired/kbod/config.h +++ b/keyboards/handwired/kbod/config.h @@ -53,7 +53,7 @@ along with this program. If not, see <http://www.gnu.org/licenses/>. // #define BACKLIGHT_LEVELS 3 /* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */ -#define DEBOUNCING_DELAY 5 +#define DEBOUNCE 5 /* define if matrix has ghost (lacks anti-ghosting diodes) */ //#define MATRIX_HAS_GHOST diff --git a/keyboards/handwired/maartenwut/config.h b/keyboards/handwired/maartenwut/config.h index b939fa1f6..d059c6e4a 100755 --- a/keyboards/handwired/maartenwut/config.h +++ b/keyboards/handwired/maartenwut/config.h @@ -32,7 +32,7 @@ #define DIODE_DIRECTION COL2ROW /* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */ -#define DEBOUNCING_DELAY 5 +#define DEBOUNCE 5 #define QMK_ESC_OUTPUT C6 // usually COL #define QMK_ESC_INPUT D0 // usually ROW diff --git a/keyboards/handwired/magicforce61/config.h b/keyboards/handwired/magicforce61/config.h index 3dc74f83e..446f4aefc 100644 --- a/keyboards/handwired/magicforce61/config.h +++ b/keyboards/handwired/magicforce61/config.h @@ -53,7 +53,7 @@ along with this program. If not, see <http://www.gnu.org/licenses/>. // #define BACKLIGHT_LEVELS 3 /* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */ -#define DEBOUNCING_DELAY 5 +#define DEBOUNCE 5 /* define if matrix has ghost (lacks anti-ghosting diodes) */ //#define MATRIX_HAS_GHOST diff --git a/keyboards/handwired/magicforce68/config.h b/keyboards/handwired/magicforce68/config.h index dc0a82c94..1cb7e91b4 100644 --- a/keyboards/handwired/magicforce68/config.h +++ b/keyboards/handwired/magicforce68/config.h @@ -54,7 +54,7 @@ along with this program. If not, see <http://www.gnu.org/licenses/>. // #define BACKLIGHT_LEVELS 3 /* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */ -#define DEBOUNCING_DELAY 5 +#define DEBOUNCE 5 /* define if matrix has ghost (lacks anti-ghosting diodes) */ //#define MATRIX_HAS_GHOST diff --git a/keyboards/handwired/mechboards_micropad/config.h b/keyboards/handwired/mechboards_micropad/config.h index 01a0bdd90..8f237a64a 100644 --- a/keyboards/handwired/mechboards_micropad/config.h +++ b/keyboards/handwired/mechboards_micropad/config.h @@ -80,7 +80,7 @@ along with this program. If not, see <http://www.gnu.org/licenses/>. // #endif /* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */ -#define DEBOUNCING_DELAY 5 +#define DEBOUNCE 5 /* define if matrix has ghost (lacks anti-ghosting diodes) */ //#define MATRIX_HAS_GHOST diff --git a/keyboards/handwired/minorca/config.h b/keyboards/handwired/minorca/config.h index c30d54db7..fea201b9c 100644 --- a/keyboards/handwired/minorca/config.h +++ b/keyboards/handwired/minorca/config.h @@ -47,7 +47,7 @@ along with this program. If not, see <http://www.gnu.org/licenses/>. #define BACKLIGHT_LEVELS 3 /* Set 0 if debouncing isn't needed */ -#define DEBOUNCING_DELAY 5 +#define DEBOUNCE 5 /* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ #define LOCKING_SUPPORT_ENABLE diff --git a/keyboards/handwired/ms_sculpt_mobile/config.h b/keyboards/handwired/ms_sculpt_mobile/config.h index 6739b44fc..0b1d3e6b3 100644 --- a/keyboards/handwired/ms_sculpt_mobile/config.h +++ b/keyboards/handwired/ms_sculpt_mobile/config.h @@ -52,7 +52,7 @@ along with this program. If not, see <http://www.gnu.org/licenses/>. #define DIODE_DIRECTION ROW2COL /* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */ -#define DEBOUNCING_DELAY 5 +#define DEBOUNCE 5 /* define if matrix has ghost (lacks anti-ghosting diodes) */ //#define MATRIX_HAS_GHOST diff --git a/keyboards/handwired/not_so_minidox/config.h b/keyboards/handwired/not_so_minidox/config.h index fc6068628..e92621af4 100644 --- a/keyboards/handwired/not_so_minidox/config.h +++ b/keyboards/handwired/not_so_minidox/config.h @@ -54,7 +54,7 @@ along with this program. If not, see <http://www.gnu.org/licenses/>. // #define BACKLIGHT_LEVELS 3 /* Set 0 if debouncing isn't needed */ -#define DEBOUNCING_DELAY 5 +#define DEBOUNCE 5 /* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ #define LOCKING_SUPPORT_ENABLE diff --git a/keyboards/handwired/numbrero/config.h b/keyboards/handwired/numbrero/config.h index bb178bd22..ac38e0814 100644 --- a/keyboards/handwired/numbrero/config.h +++ b/keyboards/handwired/numbrero/config.h @@ -29,7 +29,7 @@ #endif /* Set 0 if debouncing isn't needed */ -#define DEBOUNCING_DELAY 5 +#define DEBOUNCE 5 /* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ #define LOCKING_SUPPORT_ENABLE diff --git a/keyboards/handwired/numpad20/config.h b/keyboards/handwired/numpad20/config.h index c597494c4..78d95965a 100644 --- a/keyboards/handwired/numpad20/config.h +++ b/keyboards/handwired/numpad20/config.h @@ -54,7 +54,7 @@ along with this program. If not, see <http://www.gnu.org/licenses/>. // #define BACKLIGHT_LEVELS 3 /* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */ -#define DEBOUNCING_DELAY 5 +#define DEBOUNCE 5 /* define if matrix has ghost (lacks anti-ghosting diodes) */ //#define MATRIX_HAS_GHOST diff --git a/keyboards/handwired/onekey/bluepill/boards/GENERIC_STM32_F103/board.c b/keyboards/handwired/onekey/bluepill/boards/GENERIC_STM32_F103/board.c new file mode 100644 index 000000000..8c5a87f35 --- /dev/null +++ b/keyboards/handwired/onekey/bluepill/boards/GENERIC_STM32_F103/board.c @@ -0,0 +1,56 @@ +/* + ChibiOS - Copyright (C) 2006..2015 Giovanni Di Sirio + + Licensed under the Apache License, Version 2.0 (the "License"); + you may not use this file except in compliance with the License. + You may obtain a copy of the License at + + http://www.apache.org/licenses/LICENSE-2.0 + + Unless required by applicable law or agreed to in writing, software + distributed under the License is distributed on an "AS IS" BASIS, + WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. + See the License for the specific language governing permissions and + limitations under the License. +*/ + +#include "hal.h" + +// Value to place in RTC backup register 10 for persistent bootloader mode +#define RTC_BOOTLOADER_FLAG 0x424C + +/** + * @brief PAL setup. + * @details Digital I/O ports static configuration as defined in @p board.h. + * This variable is used by the HAL when initializing the PAL driver. + */ +#if HAL_USE_PAL || defined(__DOXYGEN__) +const PALConfig pal_default_config = +{ + {VAL_GPIOAODR, VAL_GPIOACRL, VAL_GPIOACRH}, + {VAL_GPIOBODR, VAL_GPIOBCRL, VAL_GPIOBCRH}, + {VAL_GPIOCODR, VAL_GPIOCCRL, VAL_GPIOCCRH}, + {VAL_GPIODODR, VAL_GPIODCRL, VAL_GPIODCRH}, + {VAL_GPIOEODR, VAL_GPIOECRL, VAL_GPIOECRH}, +}; +#endif + +/* + * Early initialization code. + * This initialization must be performed just after stack setup and before + * any other initialization. + */ +void __early_init(void) { + + stm32_clock_init(); +} + +/* + * Board-specific initialization code. + */ +void boardInit(void) { + //JTAG-DP Disabled and SW-DP Enabled + AFIO->MAPR |= AFIO_MAPR_SWJ_CFG_JTAGDISABLE; + //Set backup register DR10 to enter bootloader on reset + BKP->DR10 = RTC_BOOTLOADER_FLAG; +} diff --git a/keyboards/handwired/onekey/bluepill/boards/GENERIC_STM32_F103/board.h b/keyboards/handwired/onekey/bluepill/boards/GENERIC_STM32_F103/board.h new file mode 100644 index 000000000..9427adabf --- /dev/null +++ b/keyboards/handwired/onekey/bluepill/boards/GENERIC_STM32_F103/board.h @@ -0,0 +1,166 @@ +/* + ChibiOS - Copyright (C) 2006..2015 Giovanni Di Sirio + + Licensed under the Apache License, Version 2.0 (the "License"); + you may not use this file except in compliance with the License. + You may obtain a copy of the License at + + http://www.apache.org/licenses/LICENSE-2.0 + + Unless required by applicable law or agreed to in writing, software + distributed under the License is distributed on an "AS IS" BASIS, + WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. + See the License for the specific language governing permissions and + limitations under the License. +*/ + +#ifndef _BOARD_H_ +#define _BOARD_H_ + +/* + * Setup for a Generic STM32F103 board. + */ + +/* + * Board identifier. + */ +#define BOARD_GENERIC_STM32_F103 +#define BOARD_NAME "Generic STM32F103x board" + +/* + * Board frequencies. + */ +#define STM32_LSECLK 32768 +#define STM32_HSECLK 8000000 + +/* + * MCU type, supported types are defined in ./os/hal/platforms/hal_lld.h. + */ +#define STM32F103xB + +/* + * IO pins assignments + */ + +/* on-board */ + +#define GPIOA_LED 8 +#define GPIOD_OSC_IN 0 +#define GPIOD_OSC_OUT 1 + +/* In case your board has a "USB enable" hardware + controlled by a pin, define it here. (It could be just + a 1.5k resistor connected to D+ line.) +*/ +/* +#define GPIOB_USB_DISC 10 +*/ + +/* + * I/O ports initial setup, this configuration is established soon after reset + * in the initialization code. + * + * The digits have the following meaning: + * 0 - Analog input. + * 1 - Push Pull output 10MHz. + * 2 - Push Pull output 2MHz. + * 3 - Push Pull output 50MHz. + * 4 - Digital input. + * 5 - Open Drain output 10MHz. + * 6 - Open Drain output 2MHz. + * 7 - Open Drain output 50MHz. + * 8 - Digital input with PullUp or PullDown resistor depending on ODR. + * 9 - Alternate Push Pull output 10MHz. + * A - Alternate Push Pull output 2MHz. + * B - Alternate Push Pull output 50MHz. + * C - Reserved. + * D - Alternate Open Drain output 10MHz. + * E - Alternate Open Drain output 2MHz. + * F - Alternate Open Drain output 50MHz. + * Please refer to the STM32 Reference Manual for details. + */ + +/* + * Port A setup. + * Everything input with pull-up except: + * PA2 - Alternate output (USART2 TX). + * PA3 - Normal input (USART2 RX). + * PA9 - Alternate output (USART1 TX). + * PA10 - Normal input (USART1 RX). + */ +#define VAL_GPIOACRL 0x88884B88 /* PA7...PA0 */ +#define VAL_GPIOACRH 0x888884B8 /* PA15...PA8 */ +#define VAL_GPIOAODR 0xFFFFFFFF + +/* + * Port B setup. + * Everything input with pull-up except: + * PB10 - Push Pull output (USB switch). + */ +#define VAL_GPIOBCRL 0x88888888 /* PB7...PB0 */ +#define VAL_GPIOBCRH 0x88888388 /* PB15...PB8 */ +#define VAL_GPIOBODR 0xFFFFFFFF + +/* + * Port C setup. + * Everything input with pull-up except: + * PC13 - Push Pull output (LED). + */ +#define VAL_GPIOCCRL 0x88888888 /* PC7...PC0 */ +#define VAL_GPIOCCRH 0x88388888 /* PC15...PC8 */ +#define VAL_GPIOCODR 0xFFFFFFFF + +/* + * Port D setup. + * Everything input with pull-up except: + * PD0 - Normal input (XTAL). + * PD1 - Normal input (XTAL). + */ +#define VAL_GPIODCRL 0x88888844 /* PD7...PD0 */ +#define VAL_GPIODCRH 0x88888888 /* PD15...PD8 */ +#define VAL_GPIODODR 0xFFFFFFFF + +/* + * Port E setup. + * Everything input with pull-up except: + */ +#define VAL_GPIOECRL 0x88888888 /* PE7...PE0 */ +#define VAL_GPIOECRH 0x88888888 /* PE15...PE8 */ +#define VAL_GPIOEODR 0xFFFFFFFF + +/* + * USB bus activation macro, required by the USB driver. + */ +/* The point is that most of the generic STM32F103* boards + have a 1.5k resistor connected on one end to the D+ line + and on the other end to some pin. Or even a slightly more + complicated "USB enable" circuit, controlled by a pin. + That should go here. + + However on some boards (e.g. one that I have), there's no + such hardware. In which case it's better to not do anything. +*/ +/* +#define usb_lld_connect_bus(usbp) palClearPad(GPIOB, GPIOB_USB_DISC) +*/ +#define usb_lld_connect_bus(usbp) palSetPadMode(GPIOA, 12, PAL_MODE_INPUT); + +/* + * USB bus de-activation macro, required by the USB driver. + */ +/* +#define usb_lld_disconnect_bus(usbp) palSetPad(GPIOB, GPIOB_USB_DISC) +*/ +#define usb_lld_disconnect_bus(usbp) palSetPadMode(GPIOA, 12, PAL_MODE_OUTPUT_PUSHPULL); palClearPad(GPIOA, 12); + +#if !defined(_FROM_ASM_) +#ifdef __cplusplus +extern "C" { +#endif + void boardInit(void); +#ifdef __cplusplus +} +#endif +#endif /* _FROM_ASM_ */ + +#endif /* _BOARD_H_ */ diff --git a/keyboards/handwired/onekey/bluepill/boards/GENERIC_STM32_F103/board.mk b/keyboards/handwired/onekey/bluepill/boards/GENERIC_STM32_F103/board.mk new file mode 100644 index 000000000..6b8b312fd --- /dev/null +++ b/keyboards/handwired/onekey/bluepill/boards/GENERIC_STM32_F103/board.mk @@ -0,0 +1,5 @@ +# List of all the board related files. +BOARDSRC = $(BOARD_PATH)/boards/GENERIC_STM32_F103/board.c + +# Required include directories +BOARDINC = $(BOARD_PATH)/boards/GENERIC_STM32_F103 diff --git a/keyboards/handwired/onekey/bluepill/bootloader_defs.h b/keyboards/handwired/onekey/bluepill/bootloader_defs.h new file mode 100644 index 000000000..6b8fa9f72 --- /dev/null +++ b/keyboards/handwired/onekey/bluepill/bootloader_defs.h @@ -0,0 +1,10 @@ +/* Address for jumping to bootloader on STM32 chips. */ +/* It is chip dependent, the correct number can be looked up here (page 175): + * http://www.st.com/web/en/resource/technical/document/application_note/CD00167594.pdf + * This also requires a patch to chibios: + * <tmk_dir>/tmk_core/tool/chibios/ch-bootloader-jump.patch + */ + +// STM32F103* does NOT have an USB bootloader in ROM (only serial), +// so setting anything here does not make much sense +#define STM32_BOOTLOADER_ADDRESS 0x80000000 diff --git a/keyboards/handwired/onekey/bluepill/chconf.h b/keyboards/handwired/onekey/bluepill/chconf.h new file mode 100644 index 000000000..bbd9b2da6 --- /dev/null +++ b/keyboards/handwired/onekey/bluepill/chconf.h @@ -0,0 +1,524 @@ +/* + ChibiOS - Copyright (C) 2006..2015 Giovanni Di Sirio + + Licensed under the Apache License, Version 2.0 (the "License"); + you may not use this file except in compliance with the License. + You may obtain a copy of the License at + + http://www.apache.org/licenses/LICENSE-2.0 + + Unless required by applicable law or agreed to in writing, software + distributed under the License is distributed on an "AS IS" BASIS, + WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. + See the License for the specific language governing permissions and + limitations under the License. +*/ + +/** + * @file templates/chconf.h + * @brief Configuration file template. + * @details A copy of this file must be placed in each project directory, it + * contains the application specific kernel settings. + * + * @addtogroup config + * @details Kernel related settings and hooks. + * @{ + */ + +#ifndef CHCONF_H +#define CHCONF_H + +#define _CHIBIOS_RT_CONF_ + +/*===========================================================================*/ +/** + * @name System timers settings + * @{ + */ +/*===========================================================================*/ + +/** + * @brief System time counter resolution. + * @note Allowed values are 16 or 32 bits. + */ +#define CH_CFG_ST_RESOLUTION 32 + +/** + * @brief System tick frequency. + * @details Frequency of the system timer that drives the system ticks. This + * setting also defines the system tick time unit. + */ +#define CH_CFG_ST_FREQUENCY 100000 + +/** + * @brief Time delta constant for the tick-less mode. + * @note If this value is zero then the system uses the classic + * periodic tick. This value represents the minimum number + * of ticks that is safe to specify in a timeout directive. + * The value one is not valid, timeouts are rounded up to + * this value. + */ +#define CH_CFG_ST_TIMEDELTA 0 + +/** @} */ + +/*===========================================================================*/ +/** + * @name Kernel parameters and options + * @{ + */ +/*===========================================================================*/ + +/** + * @brief Round robin interval. + * @details This constant is the number of system ticks allowed for the + * threads before preemption occurs. Setting this value to zero + * disables the preemption for threads with equal priority and the + * round robin becomes cooperative. Note that higher priority + * threads can still preempt, the kernel is always preemptive. + * @note Disabling the round robin preemption makes the kernel more compact + * and generally faster. + * @note The round robin preemption is not supported in tickless mode and + * must be set to zero in that case. + */ +#define CH_CFG_TIME_QUANTUM 0 + +/** + * @brief Managed RAM size. + * @details Size of the RAM area to be managed by the OS. If set to zero + * then the whole available RAM is used. The core memory is made + * available to the heap allocator and/or can be used directly through + * the simplified core memory allocator. + * + * @note In order to let the OS manage the whole RAM the linker script must + * provide the @p __heap_base__ and @p __heap_end__ symbols. + * @note Requires @p CH_CFG_USE_MEMCORE. + */ +#define CH_CFG_MEMCORE_SIZE 0 + +/** + * @brief Idle thread automatic spawn suppression. + * @details When this option is activated the function @p chSysInit() + * does not spawn the idle thread. The application @p main() + * function becomes the idle thread and must implement an + * infinite loop. + */ +#define CH_CFG_NO_IDLE_THREAD FALSE + +/* Use __WFI in the idle thread for waiting. Does lower the power + * consumption. */ +#define CORTEX_ENABLE_WFI_IDLE TRUE + +/** @} */ + +/*===========================================================================*/ +/** + * @name Performance options + * @{ + */ +/*===========================================================================*/ + +/** + * @brief OS optimization. + * @details If enabled then time efficient rather than space efficient code + * is used when two possible implementations exist. + * + * @note This is not related to the compiler optimization options. + * @note The default is @p TRUE. + */ +#define CH_CFG_OPTIMIZE_SPEED TRUE + +/** @} */ + +/*===========================================================================*/ +/** + * @name Subsystem options + * @{ + */ +/*===========================================================================*/ + +/** + * @brief Time Measurement APIs. + * @details If enabled then the time measurement APIs are included in + * the kernel. + * + * @note The default is @p TRUE. + */ +#define CH_CFG_USE_TM FALSE + +/** + * @brief Threads registry APIs. + * @details If enabled then the registry APIs are included in the kernel. + * + * @note The default is @p TRUE. + */ +#define CH_CFG_USE_REGISTRY TRUE + +/** + * @brief Threads synchronization APIs. + * @details If enabled then the @p chThdWait() function is included in + * the kernel. + * + * @note The default is @p TRUE. + */ +#define CH_CFG_USE_WAITEXIT TRUE + +/** + * @brief Semaphores APIs. + * @details If enabled then the Semaphores APIs are included in the kernel. + * + * @note The default is @p TRUE. + */ +#define CH_CFG_USE_SEMAPHORES TRUE + +/** + * @brief Semaphores queuing mode. + * @details If enabled then the threads are enqueued on semaphores by + * priority rather than in FIFO order. + * + * @note The default is @p FALSE. Enable this if you have special + * requirements. + * @note Requires @p CH_CFG_USE_SEMAPHORES. + */ +#define CH_CFG_USE_SEMAPHORES_PRIORITY FALSE + +/** + * @brief Mutexes APIs. + * @details If enabled then the mutexes APIs are included in the kernel. + * + * @note The default is @p TRUE. + */ +#define CH_CFG_USE_MUTEXES TRUE + +/** + * @brief Enables recursive behavior on mutexes. + * @note Recursive mutexes are heavier and have an increased + * memory footprint. + * + * @note The default is @p FALSE. + * @note Requires @p CH_CFG_USE_MUTEXES. + */ +#define CH_CFG_USE_MUTEXES_RECURSIVE FALSE + +/** + * @brief Conditional Variables APIs. + * @details If enabled then the conditional variables APIs are included + * in the kernel. + * + * @note The default is @p TRUE. + * @note Requires @p CH_CFG_USE_MUTEXES. + */ +#define CH_CFG_USE_CONDVARS TRUE + +/** + * @brief Conditional Variables APIs with timeout. + * @details If enabled then the conditional variables APIs with timeout + * specification are included in the kernel. + * + * @note The default is @p TRUE. + * @note Requires @p CH_CFG_USE_CONDVARS. + */ +#define CH_CFG_USE_CONDVARS_TIMEOUT FALSE + +/** + * @brief Events Flags APIs. + * @details If enabled then the event flags APIs are included in the kernel. + * + * @note The default is @p TRUE. + */ +#define CH_CFG_USE_EVENTS TRUE + +/** + * @brief Events Flags APIs with timeout. + * @details If enabled then the events APIs with timeout specification + * are included in the kernel. + * + * @note The default is @p TRUE. + * @note Requires @p CH_CFG_USE_EVENTS. + */ +#define CH_CFG_USE_EVENTS_TIMEOUT TRUE + +/** + * @brief Synchronous Messages APIs. + * @details If enabled then the synchronous messages APIs are included + * in the kernel. + * + * @note The default is @p TRUE. + */ +#define CH_CFG_USE_MESSAGES TRUE + +/** + * @brief Synchronous Messages queuing mode. + * @details If enabled then messages are served by priority rather than in + * FIFO order. + * + * @note The default is @p FALSE. Enable this if you have special + * requirements. + * @note Requires @p CH_CFG_USE_MESSAGES. + */ +#define CH_CFG_USE_MESSAGES_PRIORITY FALSE + +/** + * @brief Mailboxes APIs. + * @details If enabled then the asynchronous messages (mailboxes) APIs are + * included in the kernel. + * + * @note The default is @p TRUE. + * @note Requires @p CH_CFG_USE_SEMAPHORES. + */ +#define CH_CFG_USE_MAILBOXES TRUE + +/** + * @brief Core Memory Manager APIs. + * @details If enabled then the core memory manager APIs are included + * in the kernel. + * + * @note The default is @p TRUE. + */ +#define CH_CFG_USE_MEMCORE TRUE + +/** + * @brief Heap Allocator APIs. + * @details If enabled then the memory heap allocator APIs are included + * in the kernel. + * + * @note The default is @p TRUE. + * @note Requires @p CH_CFG_USE_MEMCORE and either @p CH_CFG_USE_MUTEXES or + * @p CH_CFG_USE_SEMAPHORES. + * @note Mutexes are recommended. + */ +#define CH_CFG_USE_HEAP TRUE + +/** + * @brief Memory Pools Allocator APIs. + * @details If enabled then the memory pools allocator APIs are included + * in the kernel. + * + * @note The default is @p TRUE. + */ +#define CH_CFG_USE_MEMPOOLS FALSE + +/** + * @brief Dynamic Threads APIs. + * @details If enabled then the dynamic threads creation APIs are included + * in the kernel. + * + * @note The default is @p TRUE. + * @note Requires @p CH_CFG_USE_WAITEXIT. + * @note Requires @p CH_CFG_USE_HEAP and/or @p CH_CFG_USE_MEMPOOLS. + */ +#define CH_CFG_USE_DYNAMIC FALSE + +/** @} */ + +/*===========================================================================*/ +/** + * @name Debug options + * @{ + */ +/*===========================================================================*/ + +/** + * @brief Debug option, kernel statistics. + * + * @note The default is @p FALSE. + */ +#define CH_DBG_STATISTICS FALSE + +/** + * @brief Debug option, system state check. + * @details If enabled the correct call protocol for system APIs is checked + * at runtime. + * + * @note The default is @p FALSE. + */ +#define CH_DBG_SYSTEM_STATE_CHECK FALSE + +/** + * @brief Debug option, parameters checks. + * @details If enabled then the checks on the API functions input + * parameters are activated. + * + * @note The default is @p FALSE. + */ +#define CH_DBG_ENABLE_CHECKS FALSE + +/** + * @brief Debug option, consistency checks. + * @details If enabled then all the assertions in the kernel code are + * activated. This includes consistency checks inside the kernel, + * runtime anomalies and port-defined checks. + * + * @note The default is @p FALSE. + */ +#define CH_DBG_ENABLE_ASSERTS FALSE + +/** + * @brief Debug option, trace buffer. + * @details If enabled then the trace buffer is activated. + * + * @note The default is @p CH_DBG_TRACE_MASK_DISABLED. + */ +#define CH_DBG_TRACE_MASK CH_DBG_TRACE_MASK_DISABLED + +/** + * @brief Trace buffer entries. + * @note The trace buffer is only allocated if @p CH_DBG_TRACE_MASK is + * different from @p CH_DBG_TRACE_MASK_DISABLED. + */ +#define CH_DBG_TRACE_BUFFER_SIZE 128 + +/** + * @brief Debug option, stack checks. + * @details If enabled then a runtime stack check is performed. + * + * @note The default is @p FALSE. + * @note The stack check is performed in a architecture/port dependent way. + * It may not be implemented or some ports. + * @note The default failure mode is to halt the system with the global + * @p panic_msg variable set to @p NULL. + */ +#define CH_DBG_ENABLE_STACK_CHECK FALSE + +/** + * @brief Debug option, stacks initialization. + * @details If enabled then the threads working area is filled with a byte + * value when a thread is created. This can be useful for the + * runtime measurement of the used stack. + * + * @note The default is @p FALSE. + */ +#define CH_DBG_FILL_THREADS FALSE + +/** + * @brief Debug option, threads profiling. + * @details If enabled then a field is added to the @p thread_t structure that + * counts the system ticks occurred while executing the thread. + * + * @note The default is @p FALSE. + * @note This debug option is not currently compatible with the + * tickless mode. + */ +#define CH_DBG_THREADS_PROFILING FALSE + +/** @} */ + +/*===========================================================================*/ +/** + * @name Kernel hooks + * @{ + */ +/*===========================================================================*/ + +/** + * @brief Threads descriptor structure extension. + * @details User fields added to the end of the @p thread_t structure. + */ +#define CH_CFG_THREAD_EXTRA_FIELDS \ + /* Add threads custom fields here.*/ + +/** + * @brief Threads initialization hook. + * @details User initialization code added to the @p chThdInit() API. + * + * @note It is invoked from within @p chThdInit() and implicitly from all + * the threads creation APIs. + */ +#define CH_CFG_THREAD_INIT_HOOK(tp) { \ + /* Add threads initialization code here.*/ \ +} + +/** + * @brief Threads finalization hook. + * @details User finalization code added to the @p chThdExit() API. + */ +#define CH_CFG_THREAD_EXIT_HOOK(tp) { \ + /* Add threads finalization code here.*/ \ +} + +/** + * @brief Context switch hook. + * @details This hook is invoked just before switching between threads. + */ +#define CH_CFG_CONTEXT_SWITCH_HOOK(ntp, otp) { \ + /* Context switch code here.*/ \ +} + +/** + * @brief ISR enter hook. + */ +#define CH_CFG_IRQ_PROLOGUE_HOOK() { \ + /* IRQ prologue code here.*/ \ +} + +/** + * @brief ISR exit hook. + */ +#define CH_CFG_IRQ_EPILOGUE_HOOK() { \ + /* IRQ epilogue code here.*/ \ +} + +/** + * @brief Idle thread enter hook. + * @note This hook is invoked within a critical zone, no OS functions + * should be invoked from here. + * @note This macro can be used to activate a power saving mode. + */ +#define CH_CFG_IDLE_ENTER_HOOK() { \ + /* Idle-enter code here.*/ \ +} + +/** + * @brief Idle thread leave hook. + * @note This hook is invoked within a critical zone, no OS functions + * should be invoked from here. + * @note This macro can be used to deactivate a power saving mode. + */ +#define CH_CFG_IDLE_LEAVE_HOOK() { \ + /* Idle-leave code here.*/ \ +} + +/** + * @brief Idle Loop hook. + * @details This hook is continuously invoked by the idle thread loop. + */ +#define CH_CFG_IDLE_LOOP_HOOK() { \ + /* Idle loop code here.*/ \ +} + +/** + * @brief System tick event hook. + * @details This hook is invoked in the system tick handler immediately + * after processing the virtual timers queue. + */ +#define CH_CFG_SYSTEM_TICK_HOOK() { \ + /* System tick event code here.*/ \ +} + +/** + * @brief System halt hook. + * @details This hook is invoked in case to a system halting error before + * the system is halted. + */ +#define CH_CFG_SYSTEM_HALT_HOOK(reason) { \ + /* System halt code here.*/ \ +} + +/** + * @brief Trace hook. + * @details This hook is invoked each time a new record is written in the + * trace buffer. + */ +#define CH_CFG_TRACE_HOOK(tep) { \ + /* Trace code here.*/ \ +} + +/** @} */ + +/*===========================================================================*/ +/* Port-specific settings (override port settings defaulted in chcore.h). */ +/*===========================================================================*/ + +#endif /* CHCONF_H */ + +/** @} */ diff --git a/keyboards/handwired/onekey/bluepill/config.h b/keyboards/handwired/onekey/bluepill/config.h new file mode 100644 index 000000000..3d88ee00e --- /dev/null +++ b/keyboards/handwired/onekey/bluepill/config.h @@ -0,0 +1,23 @@ +/* Copyright 2019 + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#pragma once + +#include "config_common.h" + +#define MATRIX_COL_PINS { B0 } +#define MATRIX_ROW_PINS { A7 } +#define UNUSED_PINS diff --git a/keyboards/handwired/onekey/bluepill/halconf.h b/keyboards/handwired/onekey/bluepill/halconf.h new file mode 100644 index 000000000..72879a575 --- /dev/null +++ b/keyboards/handwired/onekey/bluepill/halconf.h @@ -0,0 +1,353 @@ +/* + ChibiOS - Copyright (C) 2006..2015 Giovanni Di Sirio + + Licensed under the Apache License, Version 2.0 (the "License"); + you may not use this file except in compliance with the License. + You may obtain a copy of the License at + + http://www.apache.org/licenses/LICENSE-2.0 + + Unless required by applicable law or agreed to in writing, software + distributed under the License is distributed on an "AS IS" BASIS, + WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. + See the License for the specific language governing permissions and + limitations under the License. +*/ + +/** + * @file templates/halconf.h + * @brief HAL configuration header. + * @details HAL configuration file, this file allows to enable or disable the + * various device drivers from your application. You may also use + * this file in order to override the device drivers default settings. + * + * @addtogroup HAL_CONF + * @{ + */ + +#ifndef _HALCONF_H_ +#define _HALCONF_H_ + +#include "mcuconf.h" + +/** + * @brief Enables the PAL subsystem. + */ +#if !defined(HAL_USE_PAL) || defined(__DOXYGEN__) +#define HAL_USE_PAL TRUE +#endif + +/** + * @brief Enables the ADC subsystem. + */ +#if !defined(HAL_USE_ADC) || defined(__DOXYGEN__) +#define HAL_USE_ADC FALSE +#endif + +/** + * @brief Enables the CAN subsystem. + */ +#if !defined(HAL_USE_CAN) || defined(__DOXYGEN__) +#define HAL_USE_CAN FALSE +#endif + +/** + * @brief Enables the DAC subsystem. + */ +#if !defined(HAL_USE_DAC) || defined(__DOXYGEN__) +#define HAL_USE_DAC FALSE +#endif + +/** + * @brief Enables the EXT subsystem. + */ +#if !defined(HAL_USE_EXT) || defined(__DOXYGEN__) +#define HAL_USE_EXT FALSE +#endif + +/** + * @brief Enables the GPT subsystem. + */ +#if !defined(HAL_USE_GPT) || defined(__DOXYGEN__) +#define HAL_USE_GPT FALSE +#endif + +/** + * @brief Enables the I2C subsystem. + */ +#if !defined(HAL_USE_I2C) || defined(__DOXYGEN__) +#define HAL_USE_I2C FALSE +#endif + +/** + * @brief Enables the I2S subsystem. + */ +#if !defined(HAL_USE_I2S) || defined(__DOXYGEN__) +#define HAL_USE_I2S FALSE +#endif + +/** + * @brief Enables the ICU subsystem. + */ +#if !defined(HAL_USE_ICU) || defined(__DOXYGEN__) +#define HAL_USE_ICU FALSE +#endif + +/** + * @brief Enables the MAC subsystem. + */ +#if !defined(HAL_USE_MAC) || defined(__DOXYGEN__) +#define HAL_USE_MAC FALSE +#endif + +/** + * @brief Enables the MMC_SPI subsystem. + */ +#if !defined(HAL_USE_MMC_SPI) || defined(__DOXYGEN__) +#define HAL_USE_MMC_SPI FALSE +#endif + +/** + * @brief Enables the PWM subsystem. + */ +#if !defined(HAL_USE_PWM) || defined(__DOXYGEN__) +#define HAL_USE_PWM TRUE +#endif + +/** + * @brief Enables the RTC subsystem. + */ +#if !defined(HAL_USE_RTC) || defined(__DOXYGEN__) +#define HAL_USE_RTC FALSE +#endif + +/** + * @brief Enables the SDC subsystem. + */ +#if !defined(HAL_USE_SDC) || defined(__DOXYGEN__) +#define HAL_USE_SDC FALSE +#endif + +/** + * @brief Enables the SERIAL subsystem. + */ +#if !defined(HAL_USE_SERIAL) || defined(__DOXYGEN__) +#define HAL_USE_SERIAL FALSE +#endif + +/** + * @brief Enables the SERIAL over USB subsystem. + */ +#if !defined(HAL_USE_SERIAL_USB) || defined(__DOXYGEN__) +#define HAL_USE_SERIAL_USB FALSE +#endif + +/** + * @brief Enables the SPI subsystem. + */ +#if !defined(HAL_USE_SPI) || defined(__DOXYGEN__) +#define HAL_USE_SPI TRUE +#endif + +/** + * @brief Enables the UART subsystem. + */ +#if !defined(HAL_USE_UART) || defined(__DOXYGEN__) +#define HAL_USE_UART FALSE +#endif + +/** + * @brief Enables the USB subsystem. + */ +#if !defined(HAL_USE_USB) || defined(__DOXYGEN__) +#define HAL_USE_USB TRUE +#endif + +/** + * @brief Enables the WDG subsystem. + */ +#if !defined(HAL_USE_WDG) || defined(__DOXYGEN__) +#define HAL_USE_WDG FALSE +#endif + +/*===========================================================================*/ +/* ADC driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Enables synchronous APIs. + * @note Disabling this option saves both code and data space. + */ +#if !defined(ADC_USE_WAIT) || defined(__DOXYGEN__) +#define ADC_USE_WAIT TRUE +#endif + +/** + * @brief Enables the @p adcAcquireBus() and @p adcReleaseBus() APIs. + * @note Disabling this option saves both code and data space. + */ +#if !defined(ADC_USE_MUTUAL_EXCLUSION) || defined(__DOXYGEN__) +#define ADC_USE_MUTUAL_EXCLUSION TRUE +#endif + +/*===========================================================================*/ +/* CAN driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Sleep mode related APIs inclusion switch. + */ +#if !defined(CAN_USE_SLEEP_MODE) || defined(__DOXYGEN__) +#define CAN_USE_SLEEP_MODE TRUE +#endif + +/*===========================================================================*/ +/* I2C driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Enables the mutual exclusion APIs on the I2C bus. + */ +#if !defined(I2C_USE_MUTUAL_EXCLUSION) || defined(__DOXYGEN__) +#define I2C_USE_MUTUAL_EXCLUSION TRUE +#endif + +/*===========================================================================*/ +/* MAC driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Enables an event sources for incoming packets. + */ +#if !defined(MAC_USE_ZERO_COPY) || defined(__DOXYGEN__) +#define MAC_USE_ZERO_COPY FALSE +#endif + +/** + * @brief Enables an event sources for incoming packets. + */ +#if !defined(MAC_USE_EVENTS) || defined(__DOXYGEN__) +#define MAC_USE_EVENTS TRUE +#endif + +/*===========================================================================*/ +/* MMC_SPI driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Delays insertions. + * @details If enabled this options inserts delays into the MMC waiting + * routines releasing some extra CPU time for the threads with + * lower priority, this may slow down the driver a bit however. + * This option is recommended also if the SPI driver does not + * use a DMA channel and heavily loads the CPU. + */ +#if !defined(MMC_NICE_WAITING) || defined(__DOXYGEN__) +#define MMC_NICE_WAITING TRUE +#endif + +/*===========================================================================*/ +/* SDC driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Number of initialization attempts before rejecting the card. + * @note Attempts are performed at 10mS intervals. + */ +#if !defined(SDC_INIT_RETRY) || defined(__DOXYGEN__) +#define SDC_INIT_RETRY 100 +#endif + +/** + * @brief Include support for MMC cards. + * @note MMC support is not yet implemented so this option must be kept + * at @p FALSE. + */ +#if !defined(SDC_MMC_SUPPORT) || defined(__DOXYGEN__) +#define SDC_MMC_SUPPORT FALSE +#endif + +/** + * @brief Delays insertions. + * @details If enabled this options inserts delays into the MMC waiting + * routines releasing some extra CPU time for the threads with + * lower priority, this may slow down the driver a bit however. + */ +#if !defined(SDC_NICE_WAITING) || defined(__DOXYGEN__) +#define SDC_NICE_WAITING TRUE +#endif + +/*===========================================================================*/ +/* SERIAL driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Default bit rate. + * @details Configuration parameter, this is the baud rate selected for the + * default configuration. + */ +#if !defined(SERIAL_DEFAULT_BITRATE) || defined(__DOXYGEN__) +#define SERIAL_DEFAULT_BITRATE 38400 +#endif + +/** + * @brief Serial buffers size. + * @details Configuration parameter, you can change the depth of the queue + * buffers depending on the requirements of your application. + * @note The default is 64 bytes for both the transmission and receive + * buffers. + */ +#if !defined(SERIAL_BUFFERS_SIZE) || defined(__DOXYGEN__) +#define SERIAL_BUFFERS_SIZE 16 +#endif + +/*===========================================================================*/ +/* SERIAL_USB driver related setting. */ +/*===========================================================================*/ + +/** + * @brief Serial over USB buffers size. + * @details Configuration parameter, the buffer size must be a multiple of + * the USB data endpoint maximum packet size. + * @note The default is 64 bytes for both the transmission and receive + * buffers. + */ +#if !defined(SERIAL_USB_BUFFERS_SIZE) || defined(__DOXYGEN__) +#define SERIAL_USB_BUFFERS_SIZE 1 +#endif + +/*===========================================================================*/ +/* SPI driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Enables synchronous APIs. + * @note Disabling this option saves both code and data space. + */ +#if !defined(SPI_USE_WAIT) || defined(__DOXYGEN__) +#define SPI_USE_WAIT TRUE +#endif + +/** + * @brief Enables the @p spiAcquireBus() and @p spiReleaseBus() APIs. + * @note Disabling this option saves both code and data space. + */ +#if !defined(SPI_USE_MUTUAL_EXCLUSION) || defined(__DOXYGEN__) +#define SPI_USE_MUTUAL_EXCLUSION TRUE +#endif + +/*===========================================================================*/ +/* USB driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Enables synchronous APIs. + * @note Disabling this option saves both code and data space. + */ +#if !defined(USB_USE_WAIT) || defined(__DOXYGEN__) +#define USB_USE_WAIT TRUE +#endif + +#endif /* _HALCONF_H_ */ + +/** @} */ diff --git a/keyboards/handwired/onekey/bluepill/ld/STM32F103x8_stm32duino_bootloader.ld b/keyboards/handwired/onekey/bluepill/ld/STM32F103x8_stm32duino_bootloader.ld new file mode 100644 index 000000000..d0688ef60 --- /dev/null +++ b/keyboards/handwired/onekey/bluepill/ld/STM32F103x8_stm32duino_bootloader.ld @@ -0,0 +1,88 @@ +/* + ChibiOS - Copyright (C) 2006..2016 Giovanni Di Sirio + + Licensed under the Apache License, Version 2.0 (the "License"); + you may not use this file except in compliance with the License. + You may obtain a copy of the License at + + http://www.apache.org/licenses/LICENSE-2.0 + + Unless required by applicable law or agreed to in writing, software + distributed under the License is distributed on an "AS IS" BASIS, + WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. + See the License for the specific language governing permissions and + limitations under the License. +*/ + +/* + * ST32F103xB memory setup for use with the maplemini bootloader. + * You will have to + * #define CORTEX_VTOR_INIT 0x5000 + * in your projects chconf.h + */ +MEMORY +{ + flash0 : org = 0x08002000, len = 64k - 0x2000 + flash1 : org = 0x00000000, len = 0 + flash2 : org = 0x00000000, len = 0 + flash3 : org = 0x00000000, len = 0 + flash4 : org = 0x00000000, len = 0 + flash5 : org = 0x00000000, len = 0 + flash6 : org = 0x00000000, len = 0 + flash7 : org = 0x00000000, len = 0 + ram0 : org = 0x20000000, len = 20k + ram1 : org = 0x00000000, len = 0 + ram2 : org = 0x00000000, len = 0 + ram3 : org = 0x00000000, len = 0 + ram4 : org = 0x00000000, len = 0 + ram5 : org = 0x00000000, len = 0 + ram6 : org = 0x00000000, len = 0 + ram7 : org = 0x00000000, len = 0 +} + +/* For each data/text section two region are defined, a virtual region + and a load region (_LMA suffix).*/ + +/* Flash region to be used for exception vectors.*/ +REGION_ALIAS("VECTORS_FLASH", flash0); +REGION_ALIAS("VECTORS_FLASH_LMA", flash0); + +/* Flash region to be used for constructors and destructors.*/ +REGION_ALIAS("XTORS_FLASH", flash0); +REGION_ALIAS("XTORS_FLASH_LMA", flash0); + +/* Flash region to be used for code text.*/ +REGION_ALIAS("TEXT_FLASH", flash0); +REGION_ALIAS("TEXT_FLASH_LMA", flash0); + +/* Flash region to be used for read only data.*/ +REGION_ALIAS("RODATA_FLASH", flash0); +REGION_ALIAS("RODATA_FLASH_LMA", flash0); + +/* Flash region to be used for various.*/ +REGION_ALIAS("VARIOUS_FLASH", flash0); +REGION_ALIAS("VARIOUS_FLASH_LMA", flash0); + +/* Flash region to be used for RAM(n) initialization data.*/ +REGION_ALIAS("RAM_INIT_FLASH_LMA", flash0); + +/* RAM region to be used for Main stack. This stack accommodates the processing + of all exceptions and interrupts.*/ +REGION_ALIAS("MAIN_STACK_RAM", ram0); + +/* RAM region to be used for the process stack. This is the stack used by + the main() function.*/ +REGION_ALIAS("PROCESS_STACK_RAM", ram0); + +/* RAM region to be used for data segment.*/ +REGION_ALIAS("DATA_RAM", ram0); +REGION_ALIAS("DATA_RAM_LMA", flash0); + +/* RAM region to be used for BSS segment.*/ +REGION_ALIAS("BSS_RAM", ram0); + +/* RAM region to be used for the default heap.*/ +REGION_ALIAS("HEAP_RAM", ram0); + +/* Generic rules inclusion.*/ +INCLUDE rules.ld diff --git a/keyboards/handwired/onekey/bluepill/mcuconf.h b/keyboards/handwired/onekey/bluepill/mcuconf.h new file mode 100644 index 000000000..fced27289 --- /dev/null +++ b/keyboards/handwired/onekey/bluepill/mcuconf.h @@ -0,0 +1,209 @@ +/* + ChibiOS - Copyright (C) 2006..2015 Giovanni Di Sirio + + Licensed under the Apache License, Version 2.0 (the "License"); + you may not use this file except in compliance with the License. + You may obtain a copy of the License at + + http://www.apache.org/licenses/LICENSE-2.0 + + Unless required by applicable law or agreed to in writing, software + distributed under the License is distributed on an "AS IS" BASIS, + WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. + See the License for the specific language governing permissions and + limitations under the License. +*/ + +#ifndef _MCUCONF_H_ +#define _MCUCONF_H_ + +#define STM32F103_MCUCONF + +/* + * STM32F103 drivers configuration. + * The following settings override the default settings present in + * the various device driver implementation headers. + * Note that the settings for each driver only have effect if the whole + * driver is enabled in halconf.h. + * + * IRQ priorities: + * 15...0 Lowest...Highest. + * + * DMA priorities: + * 0...3 Lowest...Highest. + */ + +/* + * HAL driver system settings. + */ +#define STM32_NO_INIT FALSE +#define STM32_HSI_ENABLED TRUE +#define STM32_LSI_ENABLED FALSE +#define STM32_HSE_ENABLED TRUE +#define STM32_LSE_ENABLED FALSE +#define STM32_SW STM32_SW_PLL +#define STM32_PLLSRC STM32_PLLSRC_HSE +#define STM32_PLLXTPRE STM32_PLLXTPRE_DIV1 +#define STM32_PLLMUL_VALUE 9 +#define STM32_HPRE STM32_HPRE_DIV1 +#define STM32_PPRE1 STM32_PPRE1_DIV2 +#define STM32_PPRE2 STM32_PPRE2_DIV2 +#define STM32_ADCPRE STM32_ADCPRE_DIV4 +#define STM32_USB_CLOCK_REQUIRED TRUE +#define STM32_USBPRE STM32_USBPRE_DIV1P5 +#define STM32_MCOSEL STM32_MCOSEL_NOCLOCK +#define STM32_RTCSEL STM32_RTCSEL_HSEDIV +#define STM32_PVD_ENABLE FALSE +#define STM32_PLS STM32_PLS_LEV0 + +/* + * ADC driver system settings. + */ +#define STM32_ADC_USE_ADC1 FALSE +#define STM32_ADC_ADC1_DMA_PRIORITY 2 +#define STM32_ADC_ADC1_IRQ_PRIORITY 6 + +/* + * CAN driver system settings. + */ +#define STM32_CAN_USE_CAN1 FALSE +#define STM32_CAN_CAN1_IRQ_PRIORITY 11 + +/* + * EXT driver system settings. + */ +#define STM32_EXT_EXTI0_IRQ_PRIORITY 6 +#define STM32_EXT_EXTI1_IRQ_PRIORITY 6 +#define STM32_EXT_EXTI2_IRQ_PRIORITY 6 +#define STM32_EXT_EXTI3_IRQ_PRIORITY 6 +#define STM32_EXT_EXTI4_IRQ_PRIORITY 6 +#define STM32_EXT_EXTI5_9_IRQ_PRIORITY 6 +#define STM32_EXT_EXTI10_15_IRQ_PRIORITY 6 +#define STM32_EXT_EXTI16_IRQ_PRIORITY 6 +#define STM32_EXT_EXTI17_IRQ_PRIORITY 6 +#define STM32_EXT_EXTI18_IRQ_PRIORITY 6 +#define STM32_EXT_EXTI19_IRQ_PRIORITY 6 + +/* + * GPT driver system settings. + */ +#define STM32_GPT_USE_TIM1 FALSE +#define STM32_GPT_USE_TIM2 FALSE +#define STM32_GPT_USE_TIM3 FALSE +#define STM32_GPT_USE_TIM4 FALSE +#define STM32_GPT_USE_TIM5 FALSE +#define STM32_GPT_USE_TIM8 FALSE +#define STM32_GPT_TIM1_IRQ_PRIORITY 7 +#define STM32_GPT_TIM2_IRQ_PRIORITY 7 +#define STM32_GPT_TIM3_IRQ_PRIORITY 7 +#define STM32_GPT_TIM4_IRQ_PRIORITY 7 +#define STM32_GPT_TIM5_IRQ_PRIORITY 7 +#define STM32_GPT_TIM8_IRQ_PRIORITY 7 + +/* + * I2C driver system settings. + */ +#define STM32_I2C_USE_I2C1 FALSE +#define STM32_I2C_USE_I2C2 FALSE +#define STM32_I2C_BUSY_TIMEOUT 50 +#define STM32_I2C_I2C1_IRQ_PRIORITY 5 +#define STM32_I2C_I2C2_IRQ_PRIORITY 5 +#define STM32_I2C_I2C1_DMA_PRIORITY 3 +#define STM32_I2C_I2C2_DMA_PRIORITY 3 +#define STM32_I2C_DMA_ERROR_HOOK(i2cp) osalSysHalt("DMA failure") + +/* + * ICU driver system settings. + */ +#define STM32_ICU_USE_TIM1 FALSE +#define STM32_ICU_USE_TIM2 FALSE +#define STM32_ICU_USE_TIM3 FALSE +#define STM32_ICU_USE_TIM4 FALSE +#define STM32_ICU_USE_TIM5 FALSE +#define STM32_ICU_USE_TIM8 FALSE +#define STM32_ICU_TIM1_IRQ_PRIORITY 7 +#define STM32_ICU_TIM2_IRQ_PRIORITY 7 +#define STM32_ICU_TIM3_IRQ_PRIORITY 7 +#define STM32_ICU_TIM4_IRQ_PRIORITY 7 +#define STM32_ICU_TIM5_IRQ_PRIORITY 7 +#define STM32_ICU_TIM8_IRQ_PRIORITY 7 + +/* + * PWM driver system settings. + */ +#define STM32_PWM_USE_ADVANCED FALSE +#define STM32_PWM_USE_TIM1 TRUE +#define STM32_PWM_USE_TIM2 FALSE +#define STM32_PWM_USE_TIM3 FALSE +#define STM32_PWM_USE_TIM4 FALSE +#define STM32_PWM_USE_TIM5 FALSE +#define STM32_PWM_USE_TIM8 FALSE +#define STM32_PWM_TIM1_IRQ_PRIORITY 7 +#define STM32_PWM_TIM2_IRQ_PRIORITY 7 +#define STM32_PWM_TIM3_IRQ_PRIORITY 7 +#define STM32_PWM_TIM4_IRQ_PRIORITY 7 +#define STM32_PWM_TIM5_IRQ_PRIORITY 7 +#define STM32_PWM_TIM8_IRQ_PRIORITY 7 + +/* + * RTC driver system settings. + */ +#define STM32_RTC_IRQ_PRIORITY 15 + +/* + * SERIAL driver system settings. + */ +#define STM32_SERIAL_USE_USART1 FALSE +#define STM32_SERIAL_USE_USART2 FALSE +#define STM32_SERIAL_USE_USART3 FALSE +#define STM32_SERIAL_USE_UART4 FALSE +#define STM32_SERIAL_USE_UART5 FALSE +#define STM32_SERIAL_USART1_PRIORITY 12 +#define STM32_SERIAL_USART2_PRIORITY 12 +#define STM32_SERIAL_USART3_PRIORITY 12 +#define STM32_SERIAL_UART4_PRIORITY 12 +#define STM32_SERIAL_UART5_PRIORITY 12 + +/* + * SPI driver system settings. + */ +#define STM32_SPI_USE_SPI1 FALSE +#define STM32_SPI_USE_SPI2 TRUE +#define STM32_SPI_USE_SPI3 FALSE +#define STM32_SPI_SPI1_DMA_PRIORITY 1 +#define STM32_SPI_SPI2_DMA_PRIORITY 1 +#define STM32_SPI_SPI3_DMA_PRIORITY 1 +#define STM32_SPI_SPI1_IRQ_PRIORITY 10 +#define STM32_SPI_SPI2_IRQ_PRIORITY 10 +#define STM32_SPI_SPI3_IRQ_PRIORITY 10 +#define STM32_SPI_DMA_ERROR_HOOK(spip) osalSysHalt("DMA failure") + +/* + * ST driver system settings. + */ +#define STM32_ST_IRQ_PRIORITY 8 +#define STM32_ST_USE_TIMER 2 + +/* + * UART driver system settings. + */ +#define STM32_UART_USE_USART1 FALSE +#define STM32_UART_USE_USART2 FALSE +#define STM32_UART_USE_USART3 FALSE +#define STM32_UART_USART1_IRQ_PRIORITY 12 +#define STM32_UART_USART2_IRQ_PRIORITY 12 +#define STM32_UART_USART3_IRQ_PRIORITY 12 +#define STM32_UART_USART1_DMA_PRIORITY 0 +#define STM32_UART_USART2_DMA_PRIORITY 0 +#define STM32_UART_USART3_DMA_PRIORITY 0 +#define STM32_UART_DMA_ERROR_HOOK(uartp) osalSysHalt("DMA failure") + +/* + * USB driver system settings. + */ +#define STM32_USB_USE_USB1 TRUE +#define STM32_USB_LOW_POWER_ON_SUSPEND FALSE +#define STM32_USB_USB1_HP_IRQ_PRIORITY 13 +#define STM32_USB_USB1_LP_IRQ_PRIORITY 14 + +#endif /* _MCUCONF_H_ */ diff --git a/keyboards/handwired/onekey/bluepill/readme.md b/keyboards/handwired/onekey/bluepill/readme.md new file mode 100644 index 000000000..0bf1f5701 --- /dev/null +++ b/keyboards/handwired/onekey/bluepill/readme.md @@ -0,0 +1,3 @@ +# bluepill onekey + +To trigger keypress, short together pins *B0* and *A7*. diff --git a/keyboards/handwired/onekey/bluepill/rules.mk b/keyboards/handwired/onekey/bluepill/rules.mk new file mode 100644 index 000000000..46274066d --- /dev/null +++ b/keyboards/handwired/onekey/bluepill/rules.mk @@ -0,0 +1,37 @@ +# GENERIC STM32F103C8T6 board - stm32duino bootloader +OPT_DEFS = -DCORTEX_VTOR_INIT=0x2000 +MCU_LDSCRIPT = STM32F103x8_stm32duino_bootloader +BOARD = GENERIC_STM32_F103 + +# OPT_DEFS = +# MCU_LDSCRIPT = STM32F103x8 +# BOARD = GENERIC_STM32_F103 + +## chip/board settings +# the next two should match the directories in +# <chibios>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES) +MCU_FAMILY = STM32 +MCU_SERIES = STM32F1xx +# linker script to use +# it should exist either in <chibios>/os/common/ports/ARMCMx/compilers/GCC/ld/ +# or <this_dir>/ld/ +# startup code to use +# is should exist in <chibios>/os/common/ports/ARMCMx/compilers/GCC/mk/ +MCU_STARTUP = stm32f1xx +# it should exist either in <chibios>/os/hal/boards/ +# or <this_dir>/boards +# Cortex version +# Teensy LC is cortex-m0; Teensy 3.x are cortex-m4 +MCU = cortex-m3 +# ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7 +ARMV = 7 +# If you want to be able to jump to bootloader from firmware on STM32 MCUs, +# set the correct BOOTLOADER_ADDRESS. Either set it here, or define it in +# ./bootloader_defs.h or in ./boards/<FOO>/bootloader_defs.h (if you have +# a custom board definition that you plan to reuse). +# If you're not setting it here, leave it commented out. +# It is chip dependent, the correct number can be looked up here (page 175): +# http://www.st.com/web/en/resource/technical/document/application_note/CD00167594.pdf +# This also requires a patch to chibios: +# <tmk_dir>/tmk_core/tool/chibios/ch-bootloader-jump.patch +#STM32_BOOTLOADER_ADDRESS = 0x1FFFC800 diff --git a/keyboards/handwired/onekey/config.h b/keyboards/handwired/onekey/config.h index 4a3042eea..6f7ec1289 100644 --- a/keyboards/handwired/onekey/config.h +++ b/keyboards/handwired/onekey/config.h @@ -15,14 +15,11 @@ You should have received a copy of the GNU General Public License along with this program. If not, see <http://www.gnu.org/licenses/>. */ -#ifndef CONFIG_H -#define CONFIG_H - -#include "config_common.h" +#pragma once /* USB Device descriptor parameter */ #define VENDOR_ID 0xFEED -#define PRODUCT_ID 0x6464 +#define PRODUCT_ID 0x6465 #define DEVICE_VER 0x0001 #define MANUFACTURER none #define PRODUCT onekey @@ -32,10 +29,6 @@ along with this program. If not, see <http://www.gnu.org/licenses/>. #define MATRIX_ROWS 1 #define MATRIX_COLS 1 -#define MATRIX_COL_PINS { B0 } -#define MATRIX_ROW_PINS { D0 } -#define UNUSED_PINS - /* define if matrix has ghost */ //#define MATRIX_HAS_GHOST @@ -64,5 +57,3 @@ along with this program. If not, see <http://www.gnu.org/licenses/>. //#define NO_ACTION_ONESHOT //#define NO_ACTION_MACRO //#define NO_ACTION_FUNCTION - -#endif diff --git a/keyboards/handwired/onekey/elite_c/config.h b/keyboards/handwired/onekey/elite_c/config.h new file mode 100644 index 000000000..fbcd630d7 --- /dev/null +++ b/keyboards/handwired/onekey/elite_c/config.h @@ -0,0 +1,23 @@ +/* Copyright 2019 + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#pragma once + +#include "config_common.h" + +#define MATRIX_COL_PINS { F4 } +#define MATRIX_ROW_PINS { F5 } +#define UNUSED_PINS diff --git a/keyboards/handwired/onekey/elite_c/readme.md b/keyboards/handwired/onekey/elite_c/readme.md new file mode 100644 index 000000000..28a0885bb --- /dev/null +++ b/keyboards/handwired/onekey/elite_c/readme.md @@ -0,0 +1,3 @@ +# Elite-C onekey + +To trigger keypress, short together pins *F4* and *F5* (marked on the PCB as *A3* and *A2*). diff --git a/keyboards/handwired/onekey/elite_c/rules.mk b/keyboards/handwired/onekey/elite_c/rules.mk new file mode 100644 index 000000000..eb7c44395 --- /dev/null +++ b/keyboards/handwired/onekey/elite_c/rules.mk @@ -0,0 +1,58 @@ +# MCU name +MCU = atmega32u4 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# atmega32a bootloadHID +BOOTLOADER = atmel-dfu + + +# If you don't know the bootloader type, then you can specify the +# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line +# Teensy halfKay 512 +# Teensy++ halfKay 1024 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +# USBaspLoader 2048 +# OPT_DEFS += -DBOOTLOADER_SIZE=4096 diff --git a/keyboards/handwired/onekey/onekey.h b/keyboards/handwired/onekey/onekey.h index 8ce6fec2d..2924ff3ff 100644 --- a/keyboards/handwired/onekey/onekey.h +++ b/keyboards/handwired/onekey/onekey.h @@ -1,5 +1,20 @@ -#ifndef ONEKEY_H -#define ONEKEY_H +/* Copyright 2019 + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#pragma once #include "quantum.h" @@ -8,5 +23,3 @@ ) { \ { k00 } \ } - -#endif diff --git a/keyboards/handwired/onekey/promicro/config.h b/keyboards/handwired/onekey/promicro/config.h new file mode 100644 index 000000000..fbcd630d7 --- /dev/null +++ b/keyboards/handwired/onekey/promicro/config.h @@ -0,0 +1,23 @@ +/* Copyright 2019 + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#pragma once + +#include "config_common.h" + +#define MATRIX_COL_PINS { F4 } +#define MATRIX_ROW_PINS { F5 } +#define UNUSED_PINS diff --git a/keyboards/handwired/onekey/promicro/readme.md b/keyboards/handwired/onekey/promicro/readme.md new file mode 100644 index 000000000..260eab83d --- /dev/null +++ b/keyboards/handwired/onekey/promicro/readme.md @@ -0,0 +1,3 @@ +# Pro Micro onekey + +To trigger keypress, short together pins *F4* and *F5* (marked on the PCB as *A3* and *A2*). diff --git a/keyboards/handwired/onekey/promicro/rules.mk b/keyboards/handwired/onekey/promicro/rules.mk new file mode 100644 index 000000000..dc6f19623 --- /dev/null +++ b/keyboards/handwired/onekey/promicro/rules.mk @@ -0,0 +1,58 @@ +# MCU name +MCU = atmega32u4 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# atmega32a bootloadHID +BOOTLOADER = caterina + + +# If you don't know the bootloader type, then you can specify the +# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line +# Teensy halfKay 512 +# Teensy++ halfKay 1024 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +# USBaspLoader 2048 +# OPT_DEFS += -DBOOTLOADER_SIZE=4096 diff --git a/keyboards/handwired/onekey/proton_c/config.h b/keyboards/handwired/onekey/proton_c/config.h new file mode 100644 index 000000000..f6bedcfe6 --- /dev/null +++ b/keyboards/handwired/onekey/proton_c/config.h @@ -0,0 +1,23 @@ +/* Copyright 2019 + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#pragma once + +#include "config_common.h" + +#define MATRIX_COL_PINS { A3 } +#define MATRIX_ROW_PINS { A2 } +#define UNUSED_PINS diff --git a/keyboards/handwired/onekey/proton_c/readme.md b/keyboards/handwired/onekey/proton_c/readme.md new file mode 100644 index 000000000..0feedbbd4 --- /dev/null +++ b/keyboards/handwired/onekey/proton_c/readme.md @@ -0,0 +1,3 @@ +# Proton C onekey + +To trigger keypress, short together pins *A3* and *A2*. diff --git a/keyboards/handwired/onekey/proton_c/rules.mk b/keyboards/handwired/onekey/proton_c/rules.mk new file mode 100644 index 000000000..b17a3d031 --- /dev/null +++ b/keyboards/handwired/onekey/proton_c/rules.mk @@ -0,0 +1,2 @@ +# MCU name +MCU = STM32F303 diff --git a/keyboards/handwired/onekey/readme.md b/keyboards/handwired/onekey/readme.md index eab3b75a9..0e9d6a538 100644 --- a/keyboards/handwired/onekey/readme.md +++ b/keyboards/handwired/onekey/readme.md @@ -2,11 +2,11 @@ Custom handwired one key keyboard. -Keyboard Maintainer: -Hardware Supported: Custom handwired one key +Keyboard Maintainer: QMK Community +Hardware Supported: bluepill, Elite-C, Pro Micro, Proton C, Teensy 2.0, Teensy++ 2.0, Teensy LC, Teensy 3.2 Hardware Availability: -Switch must be connected to pins B0 and D0. +**See each individual board for pin infomation** Make example for this keyboard (after setting up your build environment): diff --git a/keyboards/handwired/onekey/rules.mk b/keyboards/handwired/onekey/rules.mk index cfa693a73..245f9025d 100644 --- a/keyboards/handwired/onekey/rules.mk +++ b/keyboards/handwired/onekey/rules.mk @@ -1,61 +1,22 @@ - - -# MCU name -MCU = atmega32u4 - -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=4096 - - # Build Options -# comment out to disable the options. +# change yes to no to disable # -BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000) -MOUSEKEY_ENABLE = yes # Mouse keys(+4700) -EXTRAKEY_ENABLE = yes # Audio control and System control(+450) -CONSOLE_ENABLE = yes # Console for debug(+400) -COMMAND_ENABLE = yes # Commands for debug and configuration -#SLEEP_LED_ENABLE = yes # Breathing sleep LED during USB suspend -#NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA
\ No newline at end of file +BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE = yes # Mouse keys(+4700) +EXTRAKEY_ENABLE = yes # Audio control and System control(+450) +CONSOLE_ENABLE = yes # Console for debug(+400) +COMMAND_ENABLE = yes # Commands for debug and configuration +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +SLEEP_LED_ENABLE = yes # Breathing sleep LED during USB suspend +# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +NKRO_ENABLE = yes # USB Nkey Rollover +BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality on B7 by default +RGBLIGHT_ENABLE = no # Enable keyboard RGB underglow +MIDI_ENABLE = no # MIDI support (+2400 to 4200, depending on config) +UNICODE_ENABLE = no # Unicode +BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID +AUDIO_ENABLE = no # Audio output on port C6 +FAUXCLICKY_ENABLE = no # Use buzzer to emulate clicky switches +HD44780_ENABLE = no # Enable support for HD44780 based LCDs (+400) + +DEFAULT_FOLDER = handwired/onekey/promicro diff --git a/keyboards/handwired/onekey/teensy_2/config.h b/keyboards/handwired/onekey/teensy_2/config.h new file mode 100644 index 000000000..fbcd630d7 --- /dev/null +++ b/keyboards/handwired/onekey/teensy_2/config.h @@ -0,0 +1,23 @@ +/* Copyright 2019 + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#pragma once + +#include "config_common.h" + +#define MATRIX_COL_PINS { F4 } +#define MATRIX_ROW_PINS { F5 } +#define UNUSED_PINS diff --git a/keyboards/handwired/onekey/teensy_2/readme.md b/keyboards/handwired/onekey/teensy_2/readme.md new file mode 100644 index 000000000..86a3114e5 --- /dev/null +++ b/keyboards/handwired/onekey/teensy_2/readme.md @@ -0,0 +1,3 @@ +# Teensy 2.0 onekey + +To trigger keypress, short together pins *F4* and *F5* diff --git a/keyboards/handwired/onekey/teensy_2/rules.mk b/keyboards/handwired/onekey/teensy_2/rules.mk new file mode 100644 index 000000000..3fb7c7e5a --- /dev/null +++ b/keyboards/handwired/onekey/teensy_2/rules.mk @@ -0,0 +1,58 @@ +# MCU name +MCU = atmega32u4 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# atmega32a bootloadHID +BOOTLOADER = halfkay + + +# If you don't know the bootloader type, then you can specify the +# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line +# Teensy halfKay 512 +# Teensy++ halfKay 1024 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +# USBaspLoader 2048 +# OPT_DEFS += -DBOOTLOADER_SIZE=4096 diff --git a/keyboards/handwired/onekey/teensy_2pp/config.h b/keyboards/handwired/onekey/teensy_2pp/config.h new file mode 100644 index 000000000..9d993980c --- /dev/null +++ b/keyboards/handwired/onekey/teensy_2pp/config.h @@ -0,0 +1,23 @@ +/* Copyright 2019 + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#pragma once + +#include "config_common.h" + +#define MATRIX_COL_PINS { B2 } +#define MATRIX_ROW_PINS { B1 } +#define UNUSED_PINS diff --git a/keyboards/handwired/onekey/teensy_2pp/readme.md b/keyboards/handwired/onekey/teensy_2pp/readme.md new file mode 100644 index 000000000..9cb99e118 --- /dev/null +++ b/keyboards/handwired/onekey/teensy_2pp/readme.md @@ -0,0 +1,3 @@ +# Teensy++ 2.0 onekey + +To trigger keypress, short together pins *B2* and *B1* diff --git a/keyboards/handwired/onekey/teensy_2pp/rules.mk b/keyboards/handwired/onekey/teensy_2pp/rules.mk new file mode 100644 index 000000000..e318e4b9e --- /dev/null +++ b/keyboards/handwired/onekey/teensy_2pp/rules.mk @@ -0,0 +1,58 @@ +# MCU name +MCU = at90usb1286 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# atmega32a bootloadHID +BOOTLOADER = halfkay + + +# If you don't know the bootloader type, then you can specify the +# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line +# Teensy halfKay 512 +# Teensy++ halfKay 1024 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +# USBaspLoader 2048 +# OPT_DEFS += -DBOOTLOADER_SIZE=4096 diff --git a/keyboards/handwired/onekey/teensy_32/chconf.h b/keyboards/handwired/onekey/teensy_32/chconf.h new file mode 100644 index 000000000..3294ac7ee --- /dev/null +++ b/keyboards/handwired/onekey/teensy_32/chconf.h @@ -0,0 +1,524 @@ +/* + ChibiOS - Copyright (C) 2006..2015 Giovanni Di Sirio + + Licensed under the Apache License, Version 2.0 (the "License"); + you may not use this file except in compliance with the License. + You may obtain a copy of the License at + + http://www.apache.org/licenses/LICENSE-2.0 + + Unless required by applicable law or agreed to in writing, software + distributed under the License is distributed on an "AS IS" BASIS, + WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. + See the License for the specific language governing permissions and + limitations under the License. +*/ + +/** + * @file templates/chconf.h + * @brief Configuration file template. + * @details A copy of this file must be placed in each project directory, it + * contains the application specific kernel settings. + * + * @addtogroup config + * @details Kernel related settings and hooks. + * @{ + */ + +#ifndef CHCONF_H +#define CHCONF_H + +#define _CHIBIOS_RT_CONF_ + +/*===========================================================================*/ +/** + * @name System timers settings + * @{ + */ +/*===========================================================================*/ + +/** + * @brief System time counter resolution. + * @note Allowed values are 16 or 32 bits. + */ +#define CH_CFG_ST_RESOLUTION 32 + +/** + * @brief System tick frequency. + * @details Frequency of the system timer that drives the system ticks. This + * setting also defines the system tick time unit. + */ +#define CH_CFG_ST_FREQUENCY 1000 + +/** + * @brief Time delta constant for the tick-less mode. + * @note If this value is zero then the system uses the classic + * periodic tick. This value represents the minimum number + * of ticks that is safe to specify in a timeout directive. + * The value one is not valid, timeouts are rounded up to + * this value. + */ +#define CH_CFG_ST_TIMEDELTA 0 + +/** @} */ + +/*===========================================================================*/ +/** + * @name Kernel parameters and options + * @{ + */ +/*===========================================================================*/ + +/** + * @brief Round robin interval. + * @details This constant is the number of system ticks allowed for the + * threads before preemption occurs. Setting this value to zero + * disables the preemption for threads with equal priority and the + * round robin becomes cooperative. Note that higher priority + * threads can still preempt, the kernel is always preemptive. + * @note Disabling the round robin preemption makes the kernel more compact + * and generally faster. + * @note The round robin preemption is not supported in tickless mode and + * must be set to zero in that case. + */ +#define CH_CFG_TIME_QUANTUM 20 + +/** + * @brief Managed RAM size. + * @details Size of the RAM area to be managed by the OS. If set to zero + * then the whole available RAM is used. The core memory is made + * available to the heap allocator and/or can be used directly through + * the simplified core memory allocator. + * + * @note In order to let the OS manage the whole RAM the linker script must + * provide the @p __heap_base__ and @p __heap_end__ symbols. + * @note Requires @p CH_CFG_USE_MEMCORE. + */ +#define CH_CFG_MEMCORE_SIZE 0 + +/** + * @brief Idle thread automatic spawn suppression. + * @details When this option is activated the function @p chSysInit() + * does not spawn the idle thread. The application @p main() + * function becomes the idle thread and must implement an + * infinite loop. + */ +#define CH_CFG_NO_IDLE_THREAD FALSE + +/* Use __WFI in the idle thread for waiting. Does lower the power + * consumption. */ +#define CORTEX_ENABLE_WFI_IDLE TRUE + +/** @} */ + +/*===========================================================================*/ +/** + * @name Performance options + * @{ + */ +/*===========================================================================*/ + +/** + * @brief OS optimization. + * @details If enabled then time efficient rather than space efficient code + * is used when two possible implementations exist. + * + * @note This is not related to the compiler optimization options. + * @note The default is @p TRUE. + */ +#define CH_CFG_OPTIMIZE_SPEED TRUE + +/** @} */ + +/*===========================================================================*/ +/** + * @name Subsystem options + * @{ + */ +/*===========================================================================*/ + +/** + * @brief Time Measurement APIs. + * @details If enabled then the time measurement APIs are included in + * the kernel. + * + * @note The default is @p TRUE. + */ +#define CH_CFG_USE_TM FALSE + +/** + * @brief Threads registry APIs. + * @details If enabled then the registry APIs are included in the kernel. + * + * @note The default is @p TRUE. + */ +#define CH_CFG_USE_REGISTRY TRUE + +/** + * @brief Threads synchronization APIs. + * @details If enabled then the @p chThdWait() function is included in + * the kernel. + * + * @note The default is @p TRUE. + */ +#define CH_CFG_USE_WAITEXIT TRUE + +/** + * @brief Semaphores APIs. + * @details If enabled then the Semaphores APIs are included in the kernel. + * + * @note The default is @p TRUE. + */ +#define CH_CFG_USE_SEMAPHORES TRUE + +/** + * @brief Semaphores queuing mode. + * @details If enabled then the threads are enqueued on semaphores by + * priority rather than in FIFO order. + * + * @note The default is @p FALSE. Enable this if you have special + * requirements. + * @note Requires @p CH_CFG_USE_SEMAPHORES. + */ +#define CH_CFG_USE_SEMAPHORES_PRIORITY FALSE + +/** + * @brief Mutexes APIs. + * @details If enabled then the mutexes APIs are included in the kernel. + * + * @note The default is @p TRUE. + */ +#define CH_CFG_USE_MUTEXES TRUE + +/** + * @brief Enables recursive behavior on mutexes. + * @note Recursive mutexes are heavier and have an increased + * memory footprint. + * + * @note The default is @p FALSE. + * @note Requires @p CH_CFG_USE_MUTEXES. + */ +#define CH_CFG_USE_MUTEXES_RECURSIVE FALSE + +/** + * @brief Conditional Variables APIs. + * @details If enabled then the conditional variables APIs are included + * in the kernel. + * + * @note The default is @p TRUE. + * @note Requires @p CH_CFG_USE_MUTEXES. + */ +#define CH_CFG_USE_CONDVARS TRUE + +/** + * @brief Conditional Variables APIs with timeout. + * @details If enabled then the conditional variables APIs with timeout + * specification are included in the kernel. + * + * @note The default is @p TRUE. + * @note Requires @p CH_CFG_USE_CONDVARS. + */ +#define CH_CFG_USE_CONDVARS_TIMEOUT TRUE + +/** + * @brief Events Flags APIs. + * @details If enabled then the event flags APIs are included in the kernel. + * + * @note The default is @p TRUE. + */ +#define CH_CFG_USE_EVENTS TRUE + +/** + * @brief Events Flags APIs with timeout. + * @details If enabled then the events APIs with timeout specification + * are included in the kernel. + * + * @note The default is @p TRUE. + * @note Requires @p CH_CFG_USE_EVENTS. + */ +#define CH_CFG_USE_EVENTS_TIMEOUT TRUE + +/** + * @brief Synchronous Messages APIs. + * @details If enabled then the synchronous messages APIs are included + * in the kernel. + * + * @note The default is @p TRUE. + */ +#define CH_CFG_USE_MESSAGES TRUE + +/** + * @brief Synchronous Messages queuing mode. + * @details If enabled then messages are served by priority rather than in + * FIFO order. + * + * @note The default is @p FALSE. Enable this if you have special + * requirements. + * @note Requires @p CH_CFG_USE_MESSAGES. + */ +#define CH_CFG_USE_MESSAGES_PRIORITY FALSE + +/** + * @brief Mailboxes APIs. + * @details If enabled then the asynchronous messages (mailboxes) APIs are + * included in the kernel. + * + * @note The default is @p TRUE. + * @note Requires @p CH_CFG_USE_SEMAPHORES. + */ +#define CH_CFG_USE_MAILBOXES TRUE + +/** + * @brief Core Memory Manager APIs. + * @details If enabled then the core memory manager APIs are included + * in the kernel. + * + * @note The default is @p TRUE. + */ +#define CH_CFG_USE_MEMCORE TRUE + +/** + * @brief Heap Allocator APIs. + * @details If enabled then the memory heap allocator APIs are included + * in the kernel. + * + * @note The default is @p TRUE. + * @note Requires @p CH_CFG_USE_MEMCORE and either @p CH_CFG_USE_MUTEXES or + * @p CH_CFG_USE_SEMAPHORES. + * @note Mutexes are recommended. + */ +#define CH_CFG_USE_HEAP TRUE + +/** + * @brief Memory Pools Allocator APIs. + * @details If enabled then the memory pools allocator APIs are included + * in the kernel. + * + * @note The default is @p TRUE. + */ +#define CH_CFG_USE_MEMPOOLS TRUE + +/** + * @brief Dynamic Threads APIs. + * @details If enabled then the dynamic threads creation APIs are included + * in the kernel. + * + * @note The default is @p TRUE. + * @note Requires @p CH_CFG_USE_WAITEXIT. + * @note Requires @p CH_CFG_USE_HEAP and/or @p CH_CFG_USE_MEMPOOLS. + */ +#define CH_CFG_USE_DYNAMIC TRUE + +/** @} */ + +/*===========================================================================*/ +/** + * @name Debug options + * @{ + */ +/*===========================================================================*/ + +/** + * @brief Debug option, kernel statistics. + * + * @note The default is @p FALSE. + */ +#define CH_DBG_STATISTICS FALSE + +/** + * @brief Debug option, system state check. + * @details If enabled the correct call protocol for system APIs is checked + * at runtime. + * + * @note The default is @p FALSE. + */ +#define CH_DBG_SYSTEM_STATE_CHECK TRUE + +/** + * @brief Debug option, parameters checks. + * @details If enabled then the checks on the API functions input + * parameters are activated. + * + * @note The default is @p FALSE. + */ +#define CH_DBG_ENABLE_CHECKS TRUE + +/** + * @brief Debug option, consistency checks. + * @details If enabled then all the assertions in the kernel code are + * activated. This includes consistency checks inside the kernel, + * runtime anomalies and port-defined checks. + * + * @note The default is @p FALSE. + */ +#define CH_DBG_ENABLE_ASSERTS TRUE + +/** + * @brief Debug option, trace buffer. + * @details If enabled then the trace buffer is activated. + * + * @note The default is @p CH_DBG_TRACE_MASK_DISABLED. + */ +#define CH_DBG_TRACE_MASK CH_DBG_TRACE_MASK_DISABLED + +/** + * @brief Trace buffer entries. + * @note The trace buffer is only allocated if @p CH_DBG_TRACE_MASK is + * different from @p CH_DBG_TRACE_MASK_DISABLED. + */ +#define CH_DBG_TRACE_BUFFER_SIZE 128 + +/** + * @brief Debug option, stack checks. + * @details If enabled then a runtime stack check is performed. + * + * @note The default is @p FALSE. + * @note The stack check is performed in a architecture/port dependent way. + * It may not be implemented or some ports. + * @note The default failure mode is to halt the system with the global + * @p panic_msg variable set to @p NULL. + */ +#define CH_DBG_ENABLE_STACK_CHECK TRUE + +/** + * @brief Debug option, stacks initialization. + * @details If enabled then the threads working area is filled with a byte + * value when a thread is created. This can be useful for the + * runtime measurement of the used stack. + * + * @note The default is @p FALSE. + */ +#define CH_DBG_FILL_THREADS TRUE + +/** + * @brief Debug option, threads profiling. + * @details If enabled then a field is added to the @p thread_t structure that + * counts the system ticks occurred while executing the thread. + * + * @note The default is @p FALSE. + * @note This debug option is not currently compatible with the + * tickless mode. + */ +#define CH_DBG_THREADS_PROFILING FALSE + +/** @} */ + +/*===========================================================================*/ +/** + * @name Kernel hooks + * @{ + */ +/*===========================================================================*/ + +/** + * @brief Threads descriptor structure extension. + * @details User fields added to the end of the @p thread_t structure. + */ +#define CH_CFG_THREAD_EXTRA_FIELDS \ + /* Add threads custom fields here.*/ + +/** + * @brief Threads initialization hook. + * @details User initialization code added to the @p chThdInit() API. + * + * @note It is invoked from within @p chThdInit() and implicitly from all + * the threads creation APIs. + */ +#define CH_CFG_THREAD_INIT_HOOK(tp) { \ + /* Add threads initialization code here.*/ \ +} + +/** + * @brief Threads finalization hook. + * @details User finalization code added to the @p chThdExit() API. + */ +#define CH_CFG_THREAD_EXIT_HOOK(tp) { \ + /* Add threads finalization code here.*/ \ +} + +/** + * @brief Context switch hook. + * @details This hook is invoked just before switching between threads. + */ +#define CH_CFG_CONTEXT_SWITCH_HOOK(ntp, otp) { \ + /* Context switch code here.*/ \ +} + +/** + * @brief ISR enter hook. + */ +#define CH_CFG_IRQ_PROLOGUE_HOOK() { \ + /* IRQ prologue code here.*/ \ +} + +/** + * @brief ISR exit hook. + */ +#define CH_CFG_IRQ_EPILOGUE_HOOK() { \ + /* IRQ epilogue code here.*/ \ +} + +/** + * @brief Idle thread enter hook. + * @note This hook is invoked within a critical zone, no OS functions + * should be invoked from here. + * @note This macro can be used to activate a power saving mode. + */ +#define CH_CFG_IDLE_ENTER_HOOK() { \ + /* Idle-enter code here.*/ \ +} + +/** + * @brief Idle thread leave hook. + * @note This hook is invoked within a critical zone, no OS functions + * should be invoked from here. + * @note This macro can be used to deactivate a power saving mode. + */ +#define CH_CFG_IDLE_LEAVE_HOOK() { \ + /* Idle-leave code here.*/ \ +} + +/** + * @brief Idle Loop hook. + * @details This hook is continuously invoked by the idle thread loop. + */ +#define CH_CFG_IDLE_LOOP_HOOK() { \ + /* Idle loop code here.*/ \ +} + +/** + * @brief System tick event hook. + * @details This hook is invoked in the system tick handler immediately + * after processing the virtual timers queue. + */ +#define CH_CFG_SYSTEM_TICK_HOOK() { \ + /* System tick event code here.*/ \ +} + +/** + * @brief System halt hook. + * @details This hook is invoked in case to a system halting error before + * the system is halted. + */ +#define CH_CFG_SYSTEM_HALT_HOOK(reason) { \ + /* System halt code here.*/ \ +} + +/** + * @brief Trace hook. + * @details This hook is invoked each time a new record is written in the + * trace buffer. + */ +#define CH_CFG_TRACE_HOOK(tep) { \ + /* Trace code here.*/ \ +} + +/** @} */ + +/*===========================================================================*/ +/* Port-specific settings (override port settings defaulted in chcore.h). */ +/*===========================================================================*/ + +#endif /* CHCONF_H */ + +/** @} */ diff --git a/keyboards/handwired/onekey/teensy_32/config.h b/keyboards/handwired/onekey/teensy_32/config.h new file mode 100644 index 000000000..0d82a0578 --- /dev/null +++ b/keyboards/handwired/onekey/teensy_32/config.h @@ -0,0 +1,24 @@ +/* Copyright 2019 + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#pragma once + +// TODO: including this causes "error: expected identifier before '(' token" errors +//#include "config_common.h" + +#define MATRIX_COL_PINS { D5 } +#define MATRIX_ROW_PINS { B2 } +#define UNUSED_PINS diff --git a/keyboards/handwired/onekey/teensy_32/halconf.h b/keyboards/handwired/onekey/teensy_32/halconf.h new file mode 100644 index 000000000..1b6f2adc2 --- /dev/null +++ b/keyboards/handwired/onekey/teensy_32/halconf.h @@ -0,0 +1,354 @@ +/* + ChibiOS - Copyright (C) 2006..2015 Giovanni Di Sirio + + Licensed under the Apache License, Version 2.0 (the "License"); + you may not use this file except in compliance with the License. + You may obtain a copy of the License at + + http://www.apache.org/licenses/LICENSE-2.0 + + Unless required by applicable law or agreed to in writing, software + distributed under the License is distributed on an "AS IS" BASIS, + WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. + See the License for the specific language governing permissions and + limitations under the License. +*/ + +/** + * @file templates/halconf.h + * @brief HAL configuration header. + * @details HAL configuration file, this file allows to enable or disable the + * various device drivers from your application. You may also use + * this file in order to override the device drivers default settings. + * + * @addtogroup HAL_CONF + * @{ + */ + +#ifndef _HALCONF_H_ +#define _HALCONF_H_ + +#include "mcuconf.h" + +/** + * @brief Enables the PAL subsystem. + */ +#if !defined(HAL_USE_PAL) || defined(__DOXYGEN__) +#define HAL_USE_PAL TRUE +#endif + +/** + * @brief Enables the ADC subsystem. + */ +#if !defined(HAL_USE_ADC) || defined(__DOXYGEN__) +#define HAL_USE_ADC FALSE +#endif + +/** + * @brief Enables the CAN subsystem. + */ +#if !defined(HAL_USE_CAN) || defined(__DOXYGEN__) +#define HAL_USE_CAN FALSE +#endif + +/** + * @brief Enables the DAC subsystem. + */ +#if !defined(HAL_USE_DAC) || defined(__DOXYGEN__) +#define HAL_USE_DAC FALSE +#endif + +/** + * @brief Enables the EXT subsystem. + */ +#if !defined(HAL_USE_EXT) || defined(__DOXYGEN__) +#define HAL_USE_EXT FALSE +#endif + +/** + * @brief Enables the GPT subsystem. + */ +#if !defined(HAL_USE_GPT) || defined(__DOXYGEN__) +#define HAL_USE_GPT FALSE +#endif + +/** + * @brief Enables the I2C subsystem. + */ +#if !defined(HAL_USE_I2C) || defined(__DOXYGEN__) +#define HAL_USE_I2C FALSE +#endif + +/** + * @brief Enables the I2S subsystem. + */ +#if !defined(HAL_USE_I2S) || defined(__DOXYGEN__) +#define HAL_USE_I2S FALSE +#endif + +/** + * @brief Enables the ICU subsystem. + */ +#if !defined(HAL_USE_ICU) || defined(__DOXYGEN__) +#define HAL_USE_ICU FALSE +#endif + +/** + * @brief Enables the MAC subsystem. + */ +#if !defined(HAL_USE_MAC) || defined(__DOXYGEN__) +#define HAL_USE_MAC FALSE +#endif + +/** + * @brief Enables the MMC_SPI subsystem. + */ +#if !defined(HAL_USE_MMC_SPI) || defined(__DOXYGEN__) +#define HAL_USE_MMC_SPI FALSE +#endif + +/** + * @brief Enables the PWM subsystem. + */ +#if !defined(HAL_USE_PWM) || defined(__DOXYGEN__) +#define HAL_USE_PWM FALSE +#endif + +/** + * @brief Enables the RTC subsystem. + */ +#if !defined(HAL_USE_RTC) || defined(__DOXYGEN__) +#define HAL_USE_RTC FALSE +#endif + +/** + * @brief Enables the SDC subsystem. + */ +#if !defined(HAL_USE_SDC) || defined(__DOXYGEN__) +#define HAL_USE_SDC FALSE +#endif + +/** + * @brief Enables the SERIAL subsystem. + */ +#if !defined(HAL_USE_SERIAL) || defined(__DOXYGEN__) +#define HAL_USE_SERIAL FALSE +#endif + +/** + * @brief Enables the SERIAL over USB subsystem. + */ +#if !defined(HAL_USE_SERIAL_USB) || defined(__DOXYGEN__) +#define HAL_USE_SERIAL_USB FALSE +#endif + +/** + * @brief Enables the SPI subsystem. + */ +#if !defined(HAL_USE_SPI) || defined(__DOXYGEN__) +#define HAL_USE_SPI FALSE +#endif + +/** + * @brief Enables the UART subsystem. + */ +#if !defined(HAL_USE_UART) || defined(__DOXYGEN__) +#define HAL_USE_UART FALSE +#endif + +/** + * @brief Enables the USB subsystem. + */ +#if !defined(HAL_USE_USB) || defined(__DOXYGEN__) +#define HAL_USE_USB TRUE +#endif + +/** + * @brief Enables the WDG subsystem. + */ +#if !defined(HAL_USE_WDG) || defined(__DOXYGEN__) +#define HAL_USE_WDG FALSE +#endif + +/*===========================================================================*/ +/* ADC driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Enables synchronous APIs. + * @note Disabling this option saves both code and data space. + */ +#if !defined(ADC_USE_WAIT) || defined(__DOXYGEN__) +#define ADC_USE_WAIT TRUE +#endif + +/** + * @brief Enables the @p adcAcquireBus() and @p adcReleaseBus() APIs. + * @note Disabling this option saves both code and data space. + */ +#if !defined(ADC_USE_MUTUAL_EXCLUSION) || defined(__DOXYGEN__) +#define ADC_USE_MUTUAL_EXCLUSION TRUE +#endif + +/*===========================================================================*/ +/* CAN driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Sleep mode related APIs inclusion switch. + */ +#if !defined(CAN_USE_SLEEP_MODE) || defined(__DOXYGEN__) +#define CAN_USE_SLEEP_MODE TRUE +#endif + +/*===========================================================================*/ +/* I2C driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Enables the mutual exclusion APIs on the I2C bus. + */ +#if !defined(I2C_USE_MUTUAL_EXCLUSION) || defined(__DOXYGEN__) +#define I2C_USE_MUTUAL_EXCLUSION TRUE +#endif + +/*===========================================================================*/ +/* MAC driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Enables an event sources for incoming packets. + */ +#if !defined(MAC_USE_ZERO_COPY) || defined(__DOXYGEN__) +#define MAC_USE_ZERO_COPY FALSE +#endif + +/** + * @brief Enables an event sources for incoming packets. + */ +#if !defined(MAC_USE_EVENTS) || defined(__DOXYGEN__) +#define MAC_USE_EVENTS TRUE +#endif + +/*===========================================================================*/ +/* MMC_SPI driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Delays insertions. + * @details If enabled this options inserts delays into the MMC waiting + * routines releasing some extra CPU time for the threads with + * lower priority, this may slow down the driver a bit however. + * This option is recommended also if the SPI driver does not + * use a DMA channel and heavily loads the CPU. + */ +#if !defined(MMC_NICE_WAITING) || defined(__DOXYGEN__) +#define MMC_NICE_WAITING TRUE +#endif + +/*===========================================================================*/ +/* SDC driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Number of initialization attempts before rejecting the card. + * @note Attempts are performed at 10mS intervals. + */ +#if !defined(SDC_INIT_RETRY) || defined(__DOXYGEN__) +#define SDC_INIT_RETRY 100 +#endif + +/** + * @brief Include support for MMC cards. + * @note MMC support is not yet implemented so this option must be kept + * at @p FALSE. + */ +#if !defined(SDC_MMC_SUPPORT) || defined(__DOXYGEN__) +#define SDC_MMC_SUPPORT FALSE +#endif + +/** + * @brief Delays insertions. + * @details If enabled this options inserts delays into the MMC waiting + * routines releasing some extra CPU time for the threads with + * lower priority, this may slow down the driver a bit however. + */ +#if !defined(SDC_NICE_WAITING) || defined(__DOXYGEN__) +#define SDC_NICE_WAITING TRUE +#endif + +/*===========================================================================*/ +/* SERIAL driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Default bit rate. + * @details Configuration parameter, this is the baud rate selected for the + * default configuration. + */ +#if !defined(SERIAL_DEFAULT_BITRATE) || defined(__DOXYGEN__) +#define SERIAL_DEFAULT_BITRATE 38400 +#endif + +/** + * @brief Serial buffers size. + * @details Configuration parameter, you can change the depth of the queue + * buffers depending on the requirements of your application. + * @note The default is 64 bytes for both the transmission and receive + * buffers. + */ +#if !defined(SERIAL_BUFFERS_SIZE) || defined(__DOXYGEN__) +#define SERIAL_BUFFERS_SIZE 16 +#endif + +/*===========================================================================*/ +/* SERIAL_USB driver related setting. */ +/*===========================================================================*/ + +/** + * @brief Serial over USB buffers size. + * @details Configuration parameter, the buffer size must be a multiple of + * the USB data endpoint maximum packet size. + * @note The default is 64 bytes for both the transmission and receive + * buffers. + */ +#if !defined(SERIAL_USB_BUFFERS_SIZE) || defined(__DOXYGEN__) +#define SERIAL_USB_BUFFERS_SIZE 1 +#endif + +/*===========================================================================*/ +/* SPI driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Enables synchronous APIs. + * @note Disabling this option saves both code and data space. + */ +#if !defined(SPI_USE_WAIT) || defined(__DOXYGEN__) +#define SPI_USE_WAIT TRUE +#endif + +/** + * @brief Enables the @p spiAcquireBus() and @p spiReleaseBus() APIs. + * @note Disabling this option saves both code and data space. + */ +#if !defined(SPI_USE_MUTUAL_EXCLUSION) || defined(__DOXYGEN__) +#define SPI_USE_MUTUAL_EXCLUSION TRUE +#endif + +/*===========================================================================*/ +/* USB driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Enables synchronous APIs. + * @note Disabling this option saves both code and data space. + */ +#if !defined(USB_USE_WAIT) || defined(__DOXYGEN__) +#define USB_USE_WAIT TRUE +#endif + +#endif /* _HALCONF_H_ */ + +/** @} */ + diff --git a/keyboards/handwired/onekey/teensy_32/ld/MK20DX256.ld b/keyboards/handwired/onekey/teensy_32/ld/MK20DX256.ld new file mode 100644 index 000000000..66bc6b81e --- /dev/null +++ b/keyboards/handwired/onekey/teensy_32/ld/MK20DX256.ld @@ -0,0 +1,101 @@ +/* + * Copyright (C) 2013-2016 Fabio Utzig, http://fabioutzig.com + * (C) 2016 flabbergast <s3+flabbergast@sdfeu.org> + * + * Permission is hereby granted, free of charge, to any person obtaining + * a copy of this software and associated documentation files (the "Software"), + * to deal in the Software without restriction, including without limitation + * the rights to use, copy, modify, merge, publish, distribute, sublicense, + * and/or sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS + * OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE + * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, + * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE + * SOFTWARE. + */ + +/* + * MK20DX256 memory setup. + */ +MEMORY +{ + flash0 : org = 0x00000000, len = 0x400 + flash1 : org = 0x00000400, len = 0x10 + flash2 : org = 0x00000410, len = 256k - 0x410 + flash3 : org = 0x00000000, len = 0 + flash4 : org = 0x00000000, len = 0 + flash5 : org = 0x00000000, len = 0 + flash6 : org = 0x00000000, len = 0 + flash7 : org = 0x00000000, len = 0 + ram0 : org = 0x1FFF8000, len = 64k + ram1 : org = 0x00000000, len = 0 + ram2 : org = 0x00000000, len = 0 + ram3 : org = 0x00000000, len = 0 + ram4 : org = 0x00000000, len = 0 + ram5 : org = 0x00000000, len = 0 + ram6 : org = 0x00000000, len = 0 + ram7 : org = 0x00000000, len = 0 +} + +/* Flash region for the configuration bytes.*/ +SECTIONS +{ + .cfmprotect : ALIGN(4) SUBALIGN(4) + { + KEEP(*(.cfmconfig)) + } > flash1 +} + +/* For each data/text section two region are defined, a virtual region + and a load region (_LMA suffix).*/ + +/* Flash region to be used for exception vectors.*/ +REGION_ALIAS("VECTORS_FLASH", flash0); +REGION_ALIAS("VECTORS_FLASH_LMA", flash0); + +/* Flash region to be used for constructors and destructors.*/ +REGION_ALIAS("XTORS_FLASH", flash2); +REGION_ALIAS("XTORS_FLASH_LMA", flash2); + +/* Flash region to be used for code text.*/ +REGION_ALIAS("TEXT_FLASH", flash2); +REGION_ALIAS("TEXT_FLASH_LMA", flash2); + +/* Flash region to be used for read only data.*/ +REGION_ALIAS("RODATA_FLASH", flash2); +REGION_ALIAS("RODATA_FLASH_LMA", flash2); + +/* Flash region to be used for various.*/ +REGION_ALIAS("VARIOUS_FLASH", flash2); +REGION_ALIAS("VARIOUS_FLASH_LMA", flash2); + +/* Flash region to be used for RAM(n) initialization data.*/ +REGION_ALIAS("RAM_INIT_FLASH_LMA", flash2); + +/* RAM region to be used for Main stack. This stack accommodates the processing + of all exceptions and interrupts.*/ +REGION_ALIAS("MAIN_STACK_RAM", ram0); + +/* RAM region to be used for the process stack. This is the stack used by + the main() function.*/ +REGION_ALIAS("PROCESS_STACK_RAM", ram0); + +/* RAM region to be used for data segment.*/ +REGION_ALIAS("DATA_RAM", ram0); +REGION_ALIAS("DATA_RAM_LMA", flash2); + +/* RAM region to be used for BSS segment.*/ +REGION_ALIAS("BSS_RAM", ram0); + +/* RAM region to be used for the default heap.*/ +REGION_ALIAS("HEAP_RAM", ram0); + +/* Generic rules inclusion.*/ +INCLUDE rules.ld diff --git a/keyboards/handwired/onekey/teensy_32/mcuconf.h b/keyboards/handwired/onekey/teensy_32/mcuconf.h new file mode 100644 index 000000000..13a9e3333 --- /dev/null +++ b/keyboards/handwired/onekey/teensy_32/mcuconf.h @@ -0,0 +1,45 @@ +/* + ChibiOS - Copyright (C) 2006..2015 Giovanni Di Sirio + + Licensed under the Apache License, Version 2.0 (the "License"); + you may not use this file except in compliance with the License. + You may obtain a copy of the License at + + http://www.apache.org/licenses/LICENSE-2.0 + + Unless required by applicable law or agreed to in writing, software + distributed under the License is distributed on an "AS IS" BASIS, + WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. + See the License for the specific language governing permissions and + limitations under the License. +*/ + +#ifndef _MCUCONF_H_ +#define _MCUCONF_H_ + +#define K20x_MCUCONF + +/* + * HAL driver system settings. + */ +/* PEE mode - 48MHz system clock driven by (16 MHz) external crystal. */ +#define KINETIS_MCG_MODE KINETIS_MCG_MODE_PEE +#define KINETIS_PLLCLK_FREQUENCY 96000000UL +#define KINETIS_SYSCLK_FREQUENCY 48000000UL + +/* + * SERIAL driver system settings. + */ +#define KINETIS_SERIAL_USE_UART0 TRUE + +/* + * USB driver settings + */ +#define KINETIS_USB_USE_USB0 TRUE + +/* Need to redefine this, since the default (configured for K20x) might not apply + * 2 for Teensy LC + * 5 for Teensy 3.x */ +#define KINETIS_USB_USB0_IRQ_PRIORITY 5 + +#endif /* _MCUCONF_H_ */ diff --git a/keyboards/handwired/onekey/teensy_32/readme.md b/keyboards/handwired/onekey/teensy_32/readme.md new file mode 100644 index 000000000..216aecfaf --- /dev/null +++ b/keyboards/handwired/onekey/teensy_32/readme.md @@ -0,0 +1,40 @@ +# Teensy 3.2 onekey + +To trigger keypress, short together pins *D5* and *B2* (marked on the PCB as *20* and *19*). + +## Hardware + +### Pins +When setting matrix pins, you need to use the MCU definitions instead of what is printed on the PCB. Sourced from <https://www.pjrc.com/teensy/schematic32.gif>. The following table can be used to convert between the two. + +| PCB | MCU | Notes | +|------- |-----|-----------------------------| +| 0 | B16 | | +| 1 | B17 | | +| 2 | D0 | | +| 3 | A12 | | +| 4 | A13 | | +| 5 | D7 | | +| 6 | D4 | | +| 7 | D2 | | +| 8 | D3 | | +| 9 | C3 | | +| 10 | C4 | | +| 11 | C6 | | +| 12 | C7 | | +| 13/LED | C5 | | +| 14/A0 | D1 | | +| 15/A1 | C0 | | +| 16/A2 | B0 | | +| 17/A3 | B1 | | +| 18/A4 | B3 | | +| 19/A5 | B2 | | +| 20/A6 | D5 | | +| 21/A7 | D6 | | +| 22/A8 | C1 | | +| 23/A9 | C2 | | +| 24/A10 | | ADC0_DP0 in schematic *[1]* | +| 25/A11 | | ADC0_DM0 in schematic *[1]* | +| 26/A12 | | ADC0_DP3 in schematic *[1]* | + +*[1]* - Currently not configured and may require extra work to implement. diff --git a/keyboards/handwired/onekey/teensy_32/rules.mk b/keyboards/handwired/onekey/teensy_32/rules.mk new file mode 100644 index 000000000..97171611e --- /dev/null +++ b/keyboards/handwired/onekey/teensy_32/rules.mk @@ -0,0 +1,41 @@ +## chip/board settings +# - the next two should match the directories in +# <chibios>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES) +# - For Teensies, FAMILY = KINETIS and SERIES is either +# KL2x (LC) or K20x (3.0,3.1,3.2). +MCU_FAMILY = KINETIS +MCU_SERIES = K20x + +# Linker script to use +# - it should exist either in <chibios>/os/common/ports/ARMCMx/compilers/GCC/ld/ +# or <this_dir>/ld/ +# - NOTE: a custom ld script is needed for EEPROM on Teensy LC +# - LDSCRIPT = +# - MKL26Z64 for Teensy LC +# - MK20DX128 for Teensy 3.0 +# - MK20DX256 for Teensy 3.1 and 3.2 +MCU_LDSCRIPT = MK20DX256 + +# Startup code to use +# - it should exist in <chibios>/os/common/ports/ARMCMx/compilers/GCC/mk/ +# - STARTUP = +# - kl2x for Teensy LC +# - k20x5 for Teensy 3.0 +# - k20x7 for Teensy 3.1 and 3.2 +MCU_STARTUP = k20x7 + +# Board: it should exist either in <chibios>/os/hal/boards/ +# or <this_dir>/boards +# - BOARD = +# - PJRC_TEENSY_LC for Teensy LC +# - PJRC_TEENSY_3 for Teensy 3.0 +# - PJRC_TEENSY_3_1 for Teensy 3.1 or 3.2 +BOARD = PJRC_TEENSY_3_1 + +# Cortex version +# Teensy LC is cortex-m0plus; Teensy 3.x are cortex-m4 +MCU = cortex-m4 + +# ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7 +# I.e. 6 for Teensy LC; 7 for Teensy 3.x +ARMV = 7 diff --git a/keyboards/handwired/onekey/teensy_lc/chconf.h b/keyboards/handwired/onekey/teensy_lc/chconf.h new file mode 100644 index 000000000..3294ac7ee --- /dev/null +++ b/keyboards/handwired/onekey/teensy_lc/chconf.h @@ -0,0 +1,524 @@ +/* + ChibiOS - Copyright (C) 2006..2015 Giovanni Di Sirio + + Licensed under the Apache License, Version 2.0 (the "License"); + you may not use this file except in compliance with the License. + You may obtain a copy of the License at + + http://www.apache.org/licenses/LICENSE-2.0 + + Unless required by applicable law or agreed to in writing, software + distributed under the License is distributed on an "AS IS" BASIS, + WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. + See the License for the specific language governing permissions and + limitations under the License. +*/ + +/** + * @file templates/chconf.h + * @brief Configuration file template. + * @details A copy of this file must be placed in each project directory, it + * contains the application specific kernel settings. + * + * @addtogroup config + * @details Kernel related settings and hooks. + * @{ + */ + +#ifndef CHCONF_H +#define CHCONF_H + +#define _CHIBIOS_RT_CONF_ + +/*===========================================================================*/ +/** + * @name System timers settings + * @{ + */ +/*===========================================================================*/ + +/** + * @brief System time counter resolution. + * @note Allowed values are 16 or 32 bits. + */ +#define CH_CFG_ST_RESOLUTION 32 + +/** + * @brief System tick frequency. + * @details Frequency of the system timer that drives the system ticks. This + * setting also defines the system tick time unit. + */ +#define CH_CFG_ST_FREQUENCY 1000 + +/** + * @brief Time delta constant for the tick-less mode. + * @note If this value is zero then the system uses the classic + * periodic tick. This value represents the minimum number + * of ticks that is safe to specify in a timeout directive. + * The value one is not valid, timeouts are rounded up to + * this value. + */ +#define CH_CFG_ST_TIMEDELTA 0 + +/** @} */ + +/*===========================================================================*/ +/** + * @name Kernel parameters and options + * @{ + */ +/*===========================================================================*/ + +/** + * @brief Round robin interval. + * @details This constant is the number of system ticks allowed for the + * threads before preemption occurs. Setting this value to zero + * disables the preemption for threads with equal priority and the + * round robin becomes cooperative. Note that higher priority + * threads can still preempt, the kernel is always preemptive. + * @note Disabling the round robin preemption makes the kernel more compact + * and generally faster. + * @note The round robin preemption is not supported in tickless mode and + * must be set to zero in that case. + */ +#define CH_CFG_TIME_QUANTUM 20 + +/** + * @brief Managed RAM size. + * @details Size of the RAM area to be managed by the OS. If set to zero + * then the whole available RAM is used. The core memory is made + * available to the heap allocator and/or can be used directly through + * the simplified core memory allocator. + * + * @note In order to let the OS manage the whole RAM the linker script must + * provide the @p __heap_base__ and @p __heap_end__ symbols. + * @note Requires @p CH_CFG_USE_MEMCORE. + */ +#define CH_CFG_MEMCORE_SIZE 0 + +/** + * @brief Idle thread automatic spawn suppression. + * @details When this option is activated the function @p chSysInit() + * does not spawn the idle thread. The application @p main() + * function becomes the idle thread and must implement an + * infinite loop. + */ +#define CH_CFG_NO_IDLE_THREAD FALSE + +/* Use __WFI in the idle thread for waiting. Does lower the power + * consumption. */ +#define CORTEX_ENABLE_WFI_IDLE TRUE + +/** @} */ + +/*===========================================================================*/ +/** + * @name Performance options + * @{ + */ +/*===========================================================================*/ + +/** + * @brief OS optimization. + * @details If enabled then time efficient rather than space efficient code + * is used when two possible implementations exist. + * + * @note This is not related to the compiler optimization options. + * @note The default is @p TRUE. + */ +#define CH_CFG_OPTIMIZE_SPEED TRUE + +/** @} */ + +/*===========================================================================*/ +/** + * @name Subsystem options + * @{ + */ +/*===========================================================================*/ + +/** + * @brief Time Measurement APIs. + * @details If enabled then the time measurement APIs are included in + * the kernel. + * + * @note The default is @p TRUE. + */ +#define CH_CFG_USE_TM FALSE + +/** + * @brief Threads registry APIs. + * @details If enabled then the registry APIs are included in the kernel. + * + * @note The default is @p TRUE. + */ +#define CH_CFG_USE_REGISTRY TRUE + +/** + * @brief Threads synchronization APIs. + * @details If enabled then the @p chThdWait() function is included in + * the kernel. + * + * @note The default is @p TRUE. + */ +#define CH_CFG_USE_WAITEXIT TRUE + +/** + * @brief Semaphores APIs. + * @details If enabled then the Semaphores APIs are included in the kernel. + * + * @note The default is @p TRUE. + */ +#define CH_CFG_USE_SEMAPHORES TRUE + +/** + * @brief Semaphores queuing mode. + * @details If enabled then the threads are enqueued on semaphores by + * priority rather than in FIFO order. + * + * @note The default is @p FALSE. Enable this if you have special + * requirements. + * @note Requires @p CH_CFG_USE_SEMAPHORES. + */ +#define CH_CFG_USE_SEMAPHORES_PRIORITY FALSE + +/** + * @brief Mutexes APIs. + * @details If enabled then the mutexes APIs are included in the kernel. + * + * @note The default is @p TRUE. + */ +#define CH_CFG_USE_MUTEXES TRUE + +/** + * @brief Enables recursive behavior on mutexes. + * @note Recursive mutexes are heavier and have an increased + * memory footprint. + * + * @note The default is @p FALSE. + * @note Requires @p CH_CFG_USE_MUTEXES. + */ +#define CH_CFG_USE_MUTEXES_RECURSIVE FALSE + +/** + * @brief Conditional Variables APIs. + * @details If enabled then the conditional variables APIs are included + * in the kernel. + * + * @note The default is @p TRUE. + * @note Requires @p CH_CFG_USE_MUTEXES. + */ +#define CH_CFG_USE_CONDVARS TRUE + +/** + * @brief Conditional Variables APIs with timeout. + * @details If enabled then the conditional variables APIs with timeout + * specification are included in the kernel. + * + * @note The default is @p TRUE. + * @note Requires @p CH_CFG_USE_CONDVARS. + */ +#define CH_CFG_USE_CONDVARS_TIMEOUT TRUE + +/** + * @brief Events Flags APIs. + * @details If enabled then the event flags APIs are included in the kernel. + * + * @note The default is @p TRUE. + */ +#define CH_CFG_USE_EVENTS TRUE + +/** + * @brief Events Flags APIs with timeout. + * @details If enabled then the events APIs with timeout specification + * are included in the kernel. + * + * @note The default is @p TRUE. + * @note Requires @p CH_CFG_USE_EVENTS. + */ +#define CH_CFG_USE_EVENTS_TIMEOUT TRUE + +/** + * @brief Synchronous Messages APIs. + * @details If enabled then the synchronous messages APIs are included + * in the kernel. + * + * @note The default is @p TRUE. + */ +#define CH_CFG_USE_MESSAGES TRUE + +/** + * @brief Synchronous Messages queuing mode. + * @details If enabled then messages are served by priority rather than in + * FIFO order. + * + * @note The default is @p FALSE. Enable this if you have special + * requirements. + * @note Requires @p CH_CFG_USE_MESSAGES. + */ +#define CH_CFG_USE_MESSAGES_PRIORITY FALSE + +/** + * @brief Mailboxes APIs. + * @details If enabled then the asynchronous messages (mailboxes) APIs are + * included in the kernel. + * + * @note The default is @p TRUE. + * @note Requires @p CH_CFG_USE_SEMAPHORES. + */ +#define CH_CFG_USE_MAILBOXES TRUE + +/** + * @brief Core Memory Manager APIs. + * @details If enabled then the core memory manager APIs are included + * in the kernel. + * + * @note The default is @p TRUE. + */ +#define CH_CFG_USE_MEMCORE TRUE + +/** + * @brief Heap Allocator APIs. + * @details If enabled then the memory heap allocator APIs are included + * in the kernel. + * + * @note The default is @p TRUE. + * @note Requires @p CH_CFG_USE_MEMCORE and either @p CH_CFG_USE_MUTEXES or + * @p CH_CFG_USE_SEMAPHORES. + * @note Mutexes are recommended. + */ +#define CH_CFG_USE_HEAP TRUE + +/** + * @brief Memory Pools Allocator APIs. + * @details If enabled then the memory pools allocator APIs are included + * in the kernel. + * + * @note The default is @p TRUE. + */ +#define CH_CFG_USE_MEMPOOLS TRUE + +/** + * @brief Dynamic Threads APIs. + * @details If enabled then the dynamic threads creation APIs are included + * in the kernel. + * + * @note The default is @p TRUE. + * @note Requires @p CH_CFG_USE_WAITEXIT. + * @note Requires @p CH_CFG_USE_HEAP and/or @p CH_CFG_USE_MEMPOOLS. + */ +#define CH_CFG_USE_DYNAMIC TRUE + +/** @} */ + +/*===========================================================================*/ +/** + * @name Debug options + * @{ + */ +/*===========================================================================*/ + +/** + * @brief Debug option, kernel statistics. + * + * @note The default is @p FALSE. + */ +#define CH_DBG_STATISTICS FALSE + +/** + * @brief Debug option, system state check. + * @details If enabled the correct call protocol for system APIs is checked + * at runtime. + * + * @note The default is @p FALSE. + */ +#define CH_DBG_SYSTEM_STATE_CHECK TRUE + +/** + * @brief Debug option, parameters checks. + * @details If enabled then the checks on the API functions input + * parameters are activated. + * + * @note The default is @p FALSE. + */ +#define CH_DBG_ENABLE_CHECKS TRUE + +/** + * @brief Debug option, consistency checks. + * @details If enabled then all the assertions in the kernel code are + * activated. This includes consistency checks inside the kernel, + * runtime anomalies and port-defined checks. + * + * @note The default is @p FALSE. + */ +#define CH_DBG_ENABLE_ASSERTS TRUE + +/** + * @brief Debug option, trace buffer. + * @details If enabled then the trace buffer is activated. + * + * @note The default is @p CH_DBG_TRACE_MASK_DISABLED. + */ +#define CH_DBG_TRACE_MASK CH_DBG_TRACE_MASK_DISABLED + +/** + * @brief Trace buffer entries. + * @note The trace buffer is only allocated if @p CH_DBG_TRACE_MASK is + * different from @p CH_DBG_TRACE_MASK_DISABLED. + */ +#define CH_DBG_TRACE_BUFFER_SIZE 128 + +/** + * @brief Debug option, stack checks. + * @details If enabled then a runtime stack check is performed. + * + * @note The default is @p FALSE. + * @note The stack check is performed in a architecture/port dependent way. + * It may not be implemented or some ports. + * @note The default failure mode is to halt the system with the global + * @p panic_msg variable set to @p NULL. + */ +#define CH_DBG_ENABLE_STACK_CHECK TRUE + +/** + * @brief Debug option, stacks initialization. + * @details If enabled then the threads working area is filled with a byte + * value when a thread is created. This can be useful for the + * runtime measurement of the used stack. + * + * @note The default is @p FALSE. + */ +#define CH_DBG_FILL_THREADS TRUE + +/** + * @brief Debug option, threads profiling. + * @details If enabled then a field is added to the @p thread_t structure that + * counts the system ticks occurred while executing the thread. + * + * @note The default is @p FALSE. + * @note This debug option is not currently compatible with the + * tickless mode. + */ +#define CH_DBG_THREADS_PROFILING FALSE + +/** @} */ + +/*===========================================================================*/ +/** + * @name Kernel hooks + * @{ + */ +/*===========================================================================*/ + +/** + * @brief Threads descriptor structure extension. + * @details User fields added to the end of the @p thread_t structure. + */ +#define CH_CFG_THREAD_EXTRA_FIELDS \ + /* Add threads custom fields here.*/ + +/** + * @brief Threads initialization hook. + * @details User initialization code added to the @p chThdInit() API. + * + * @note It is invoked from within @p chThdInit() and implicitly from all + * the threads creation APIs. + */ +#define CH_CFG_THREAD_INIT_HOOK(tp) { \ + /* Add threads initialization code here.*/ \ +} + +/** + * @brief Threads finalization hook. + * @details User finalization code added to the @p chThdExit() API. + */ +#define CH_CFG_THREAD_EXIT_HOOK(tp) { \ + /* Add threads finalization code here.*/ \ +} + +/** + * @brief Context switch hook. + * @details This hook is invoked just before switching between threads. + */ +#define CH_CFG_CONTEXT_SWITCH_HOOK(ntp, otp) { \ + /* Context switch code here.*/ \ +} + +/** + * @brief ISR enter hook. + */ +#define CH_CFG_IRQ_PROLOGUE_HOOK() { \ + /* IRQ prologue code here.*/ \ +} + +/** + * @brief ISR exit hook. + */ +#define CH_CFG_IRQ_EPILOGUE_HOOK() { \ + /* IRQ epilogue code here.*/ \ +} + +/** + * @brief Idle thread enter hook. + * @note This hook is invoked within a critical zone, no OS functions + * should be invoked from here. + * @note This macro can be used to activate a power saving mode. + */ +#define CH_CFG_IDLE_ENTER_HOOK() { \ + /* Idle-enter code here.*/ \ +} + +/** + * @brief Idle thread leave hook. + * @note This hook is invoked within a critical zone, no OS functions + * should be invoked from here. + * @note This macro can be used to deactivate a power saving mode. + */ +#define CH_CFG_IDLE_LEAVE_HOOK() { \ + /* Idle-leave code here.*/ \ +} + +/** + * @brief Idle Loop hook. + * @details This hook is continuously invoked by the idle thread loop. + */ +#define CH_CFG_IDLE_LOOP_HOOK() { \ + /* Idle loop code here.*/ \ +} + +/** + * @brief System tick event hook. + * @details This hook is invoked in the system tick handler immediately + * after processing the virtual timers queue. + */ +#define CH_CFG_SYSTEM_TICK_HOOK() { \ + /* System tick event code here.*/ \ +} + +/** + * @brief System halt hook. + * @details This hook is invoked in case to a system halting error before + * the system is halted. + */ +#define CH_CFG_SYSTEM_HALT_HOOK(reason) { \ + /* System halt code here.*/ \ +} + +/** + * @brief Trace hook. + * @details This hook is invoked each time a new record is written in the + * trace buffer. + */ +#define CH_CFG_TRACE_HOOK(tep) { \ + /* Trace code here.*/ \ +} + +/** @} */ + +/*===========================================================================*/ +/* Port-specific settings (override port settings defaulted in chcore.h). */ +/*===========================================================================*/ + +#endif /* CHCONF_H */ + +/** @} */ diff --git a/keyboards/handwired/onekey/teensy_lc/config.h b/keyboards/handwired/onekey/teensy_lc/config.h new file mode 100644 index 000000000..0d82a0578 --- /dev/null +++ b/keyboards/handwired/onekey/teensy_lc/config.h @@ -0,0 +1,24 @@ +/* Copyright 2019 + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#pragma once + +// TODO: including this causes "error: expected identifier before '(' token" errors +//#include "config_common.h" + +#define MATRIX_COL_PINS { D5 } +#define MATRIX_ROW_PINS { B2 } +#define UNUSED_PINS diff --git a/keyboards/handwired/onekey/teensy_lc/halconf.h b/keyboards/handwired/onekey/teensy_lc/halconf.h new file mode 100644 index 000000000..1b6f2adc2 --- /dev/null +++ b/keyboards/handwired/onekey/teensy_lc/halconf.h @@ -0,0 +1,354 @@ +/* + ChibiOS - Copyright (C) 2006..2015 Giovanni Di Sirio + + Licensed under the Apache License, Version 2.0 (the "License"); + you may not use this file except in compliance with the License. + You may obtain a copy of the License at + + http://www.apache.org/licenses/LICENSE-2.0 + + Unless required by applicable law or agreed to in writing, software + distributed under the License is distributed on an "AS IS" BASIS, + WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. + See the License for the specific language governing permissions and + limitations under the License. +*/ + +/** + * @file templates/halconf.h + * @brief HAL configuration header. + * @details HAL configuration file, this file allows to enable or disable the + * various device drivers from your application. You may also use + * this file in order to override the device drivers default settings. + * + * @addtogroup HAL_CONF + * @{ + */ + +#ifndef _HALCONF_H_ +#define _HALCONF_H_ + +#include "mcuconf.h" + +/** + * @brief Enables the PAL subsystem. + */ +#if !defined(HAL_USE_PAL) || defined(__DOXYGEN__) +#define HAL_USE_PAL TRUE +#endif + +/** + * @brief Enables the ADC subsystem. + */ +#if !defined(HAL_USE_ADC) || defined(__DOXYGEN__) +#define HAL_USE_ADC FALSE +#endif + +/** + * @brief Enables the CAN subsystem. + */ +#if !defined(HAL_USE_CAN) || defined(__DOXYGEN__) +#define HAL_USE_CAN FALSE +#endif + +/** + * @brief Enables the DAC subsystem. + */ +#if !defined(HAL_USE_DAC) || defined(__DOXYGEN__) +#define HAL_USE_DAC FALSE +#endif + +/** + * @brief Enables the EXT subsystem. + */ +#if !defined(HAL_USE_EXT) || defined(__DOXYGEN__) +#define HAL_USE_EXT FALSE +#endif + +/** + * @brief Enables the GPT subsystem. + */ +#if !defined(HAL_USE_GPT) || defined(__DOXYGEN__) +#define HAL_USE_GPT FALSE +#endif + +/** + * @brief Enables the I2C subsystem. + */ +#if !defined(HAL_USE_I2C) || defined(__DOXYGEN__) +#define HAL_USE_I2C FALSE +#endif + +/** + * @brief Enables the I2S subsystem. + */ +#if !defined(HAL_USE_I2S) || defined(__DOXYGEN__) +#define HAL_USE_I2S FALSE +#endif + +/** + * @brief Enables the ICU subsystem. + */ +#if !defined(HAL_USE_ICU) || defined(__DOXYGEN__) +#define HAL_USE_ICU FALSE +#endif + +/** + * @brief Enables the MAC subsystem. + */ +#if !defined(HAL_USE_MAC) || defined(__DOXYGEN__) +#define HAL_USE_MAC FALSE +#endif + +/** + * @brief Enables the MMC_SPI subsystem. + */ +#if !defined(HAL_USE_MMC_SPI) || defined(__DOXYGEN__) +#define HAL_USE_MMC_SPI FALSE +#endif + +/** + * @brief Enables the PWM subsystem. + */ +#if !defined(HAL_USE_PWM) || defined(__DOXYGEN__) +#define HAL_USE_PWM FALSE +#endif + +/** + * @brief Enables the RTC subsystem. + */ +#if !defined(HAL_USE_RTC) || defined(__DOXYGEN__) +#define HAL_USE_RTC FALSE +#endif + +/** + * @brief Enables the SDC subsystem. + */ +#if !defined(HAL_USE_SDC) || defined(__DOXYGEN__) +#define HAL_USE_SDC FALSE +#endif + +/** + * @brief Enables the SERIAL subsystem. + */ +#if !defined(HAL_USE_SERIAL) || defined(__DOXYGEN__) +#define HAL_USE_SERIAL FALSE +#endif + +/** + * @brief Enables the SERIAL over USB subsystem. + */ +#if !defined(HAL_USE_SERIAL_USB) || defined(__DOXYGEN__) +#define HAL_USE_SERIAL_USB FALSE +#endif + +/** + * @brief Enables the SPI subsystem. + */ +#if !defined(HAL_USE_SPI) || defined(__DOXYGEN__) +#define HAL_USE_SPI FALSE +#endif + +/** + * @brief Enables the UART subsystem. + */ +#if !defined(HAL_USE_UART) || defined(__DOXYGEN__) +#define HAL_USE_UART FALSE +#endif + +/** + * @brief Enables the USB subsystem. + */ +#if !defined(HAL_USE_USB) || defined(__DOXYGEN__) +#define HAL_USE_USB TRUE +#endif + +/** + * @brief Enables the WDG subsystem. + */ +#if !defined(HAL_USE_WDG) || defined(__DOXYGEN__) +#define HAL_USE_WDG FALSE +#endif + +/*===========================================================================*/ +/* ADC driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Enables synchronous APIs. + * @note Disabling this option saves both code and data space. + */ +#if !defined(ADC_USE_WAIT) || defined(__DOXYGEN__) +#define ADC_USE_WAIT TRUE +#endif + +/** + * @brief Enables the @p adcAcquireBus() and @p adcReleaseBus() APIs. + * @note Disabling this option saves both code and data space. + */ +#if !defined(ADC_USE_MUTUAL_EXCLUSION) || defined(__DOXYGEN__) +#define ADC_USE_MUTUAL_EXCLUSION TRUE +#endif + +/*===========================================================================*/ +/* CAN driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Sleep mode related APIs inclusion switch. + */ +#if !defined(CAN_USE_SLEEP_MODE) || defined(__DOXYGEN__) +#define CAN_USE_SLEEP_MODE TRUE +#endif + +/*===========================================================================*/ +/* I2C driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Enables the mutual exclusion APIs on the I2C bus. + */ +#if !defined(I2C_USE_MUTUAL_EXCLUSION) || defined(__DOXYGEN__) +#define I2C_USE_MUTUAL_EXCLUSION TRUE +#endif + +/*===========================================================================*/ +/* MAC driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Enables an event sources for incoming packets. + */ +#if !defined(MAC_USE_ZERO_COPY) || defined(__DOXYGEN__) +#define MAC_USE_ZERO_COPY FALSE +#endif + +/** + * @brief Enables an event sources for incoming packets. + */ +#if !defined(MAC_USE_EVENTS) || defined(__DOXYGEN__) +#define MAC_USE_EVENTS TRUE +#endif + +/*===========================================================================*/ +/* MMC_SPI driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Delays insertions. + * @details If enabled this options inserts delays into the MMC waiting + * routines releasing some extra CPU time for the threads with + * lower priority, this may slow down the driver a bit however. + * This option is recommended also if the SPI driver does not + * use a DMA channel and heavily loads the CPU. + */ +#if !defined(MMC_NICE_WAITING) || defined(__DOXYGEN__) +#define MMC_NICE_WAITING TRUE +#endif + +/*===========================================================================*/ +/* SDC driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Number of initialization attempts before rejecting the card. + * @note Attempts are performed at 10mS intervals. + */ +#if !defined(SDC_INIT_RETRY) || defined(__DOXYGEN__) +#define SDC_INIT_RETRY 100 +#endif + +/** + * @brief Include support for MMC cards. + * @note MMC support is not yet implemented so this option must be kept + * at @p FALSE. + */ +#if !defined(SDC_MMC_SUPPORT) || defined(__DOXYGEN__) +#define SDC_MMC_SUPPORT FALSE +#endif + +/** + * @brief Delays insertions. + * @details If enabled this options inserts delays into the MMC waiting + * routines releasing some extra CPU time for the threads with + * lower priority, this may slow down the driver a bit however. + */ +#if !defined(SDC_NICE_WAITING) || defined(__DOXYGEN__) +#define SDC_NICE_WAITING TRUE +#endif + +/*===========================================================================*/ +/* SERIAL driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Default bit rate. + * @details Configuration parameter, this is the baud rate selected for the + * default configuration. + */ +#if !defined(SERIAL_DEFAULT_BITRATE) || defined(__DOXYGEN__) +#define SERIAL_DEFAULT_BITRATE 38400 +#endif + +/** + * @brief Serial buffers size. + * @details Configuration parameter, you can change the depth of the queue + * buffers depending on the requirements of your application. + * @note The default is 64 bytes for both the transmission and receive + * buffers. + */ +#if !defined(SERIAL_BUFFERS_SIZE) || defined(__DOXYGEN__) +#define SERIAL_BUFFERS_SIZE 16 +#endif + +/*===========================================================================*/ +/* SERIAL_USB driver related setting. */ +/*===========================================================================*/ + +/** + * @brief Serial over USB buffers size. + * @details Configuration parameter, the buffer size must be a multiple of + * the USB data endpoint maximum packet size. + * @note The default is 64 bytes for both the transmission and receive + * buffers. + */ +#if !defined(SERIAL_USB_BUFFERS_SIZE) || defined(__DOXYGEN__) +#define SERIAL_USB_BUFFERS_SIZE 1 +#endif + +/*===========================================================================*/ +/* SPI driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Enables synchronous APIs. + * @note Disabling this option saves both code and data space. + */ +#if !defined(SPI_USE_WAIT) || defined(__DOXYGEN__) +#define SPI_USE_WAIT TRUE +#endif + +/** + * @brief Enables the @p spiAcquireBus() and @p spiReleaseBus() APIs. + * @note Disabling this option saves both code and data space. + */ +#if !defined(SPI_USE_MUTUAL_EXCLUSION) || defined(__DOXYGEN__) +#define SPI_USE_MUTUAL_EXCLUSION TRUE +#endif + +/*===========================================================================*/ +/* USB driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Enables synchronous APIs. + * @note Disabling this option saves both code and data space. + */ +#if !defined(USB_USE_WAIT) || defined(__DOXYGEN__) +#define USB_USE_WAIT TRUE +#endif + +#endif /* _HALCONF_H_ */ + +/** @} */ + diff --git a/keyboards/handwired/onekey/teensy_lc/ld/MKL26Z64.ld b/keyboards/handwired/onekey/teensy_lc/ld/MKL26Z64.ld new file mode 100644 index 000000000..c4ca8b874 --- /dev/null +++ b/keyboards/handwired/onekey/teensy_lc/ld/MKL26Z64.ld @@ -0,0 +1,105 @@ +/* + * Copyright (C) 2013-2016 Fabio Utzig, http://fabioutzig.com + * (C) 2016 flabbergast <s3+flabbergast@sdfeu.org> + * + * Permission is hereby granted, free of charge, to any person obtaining + * a copy of this software and associated documentation files (the "Software"), + * to deal in the Software without restriction, including without limitation + * the rights to use, copy, modify, merge, publish, distribute, sublicense, + * and/or sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS + * OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE + * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, + * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE + * SOFTWARE. + */ + +/* + * KL26Z64 memory setup. + */ +MEMORY +{ + flash0 : org = 0x00000000, len = 0x100 + flash1 : org = 0x00000400, len = 0x10 + flash2 : org = 0x00000410, len = 62k - 0x410 + flash3 : org = 0x0000F800, len = 2k + flash4 : org = 0x00000000, len = 0 + flash5 : org = 0x00000000, len = 0 + flash6 : org = 0x00000000, len = 0 + flash7 : org = 0x00000000, len = 0 + ram0 : org = 0x1FFFF800, len = 8k + ram1 : org = 0x00000000, len = 0 + ram2 : org = 0x00000000, len = 0 + ram3 : org = 0x00000000, len = 0 + ram4 : org = 0x00000000, len = 0 + ram5 : org = 0x00000000, len = 0 + ram6 : org = 0x00000000, len = 0 + ram7 : org = 0x00000000, len = 0 +} + +/* Flash region for the configuration bytes.*/ +SECTIONS +{ + .cfmprotect : ALIGN(4) SUBALIGN(4) + { + KEEP(*(.cfmconfig)) + } > flash1 +} + +/* For each data/text section two region are defined, a virtual region + and a load region (_LMA suffix).*/ + +/* Flash region to be used for exception vectors.*/ +REGION_ALIAS("VECTORS_FLASH", flash0); +REGION_ALIAS("VECTORS_FLASH_LMA", flash0); + +/* Flash region to be used for constructors and destructors.*/ +REGION_ALIAS("XTORS_FLASH", flash2); +REGION_ALIAS("XTORS_FLASH_LMA", flash2); + +/* Flash region to be used for code text.*/ +REGION_ALIAS("TEXT_FLASH", flash2); +REGION_ALIAS("TEXT_FLASH_LMA", flash2); + +/* Flash region to be used for read only data.*/ +REGION_ALIAS("RODATA_FLASH", flash2); +REGION_ALIAS("RODATA_FLASH_LMA", flash2); + +/* Flash region to be used for various.*/ +REGION_ALIAS("VARIOUS_FLASH", flash2); +REGION_ALIAS("VARIOUS_FLASH_LMA", flash2); + +/* Flash region to be used for RAM(n) initialization data.*/ +REGION_ALIAS("RAM_INIT_FLASH_LMA", flash2); + +/* RAM region to be used for Main stack. This stack accommodates the processing + of all exceptions and interrupts.*/ +REGION_ALIAS("MAIN_STACK_RAM", ram0); + +/* RAM region to be used for the process stack. This is the stack used by + the main() function.*/ +REGION_ALIAS("PROCESS_STACK_RAM", ram0); + +/* RAM region to be used for data segment.*/ +REGION_ALIAS("DATA_RAM", ram0); +REGION_ALIAS("DATA_RAM_LMA", flash2); + +/* RAM region to be used for BSS segment.*/ +REGION_ALIAS("BSS_RAM", ram0); + +/* RAM region to be used for the default heap.*/ +REGION_ALIAS("HEAP_RAM", ram0); + +__eeprom_workarea_start__ = ORIGIN(flash3); +__eeprom_workarea_size__ = LENGTH(flash3); +__eeprom_workarea_end__ = __eeprom_workarea_start__ + __eeprom_workarea_size__; + +/* Generic rules inclusion.*/ +INCLUDE rules.ld diff --git a/keyboards/handwired/onekey/teensy_lc/mcuconf.h b/keyboards/handwired/onekey/teensy_lc/mcuconf.h new file mode 100644 index 000000000..ea576df5b --- /dev/null +++ b/keyboards/handwired/onekey/teensy_lc/mcuconf.h @@ -0,0 +1,45 @@ +/* + ChibiOS - Copyright (C) 2006..2015 Giovanni Di Sirio + + Licensed under the Apache License, Version 2.0 (the "License"); + you may not use this file except in compliance with the License. + You may obtain a copy of the License at + + http://www.apache.org/licenses/LICENSE-2.0 + + Unless required by applicable law or agreed to in writing, software + distributed under the License is distributed on an "AS IS" BASIS, + WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. + See the License for the specific language governing permissions and + limitations under the License. +*/ + +#ifndef _MCUCONF_H_ +#define _MCUCONF_H_ + +#define KL2x_MCUCONF + +/* + * HAL driver system settings. + */ +/* PEE mode - 48MHz system clock driven by (16 MHz) external crystal. */ +#define KINETIS_MCG_MODE KINETIS_MCG_MODE_PEE +#define KINETIS_PLLCLK_FREQUENCY 96000000UL +#define KINETIS_SYSCLK_FREQUENCY 48000000UL + +/* + * SERIAL driver system settings. + */ +#define KINETIS_SERIAL_USE_UART0 TRUE + +/* + * USB driver settings + */ +#define KINETIS_USB_USE_USB0 TRUE + +/* Need to redefine this, since the default (configured for K20x) might not apply + * 2 for Teensy LC + * 5 for Teensy 3.x */ +#define KINETIS_USB_USB0_IRQ_PRIORITY 2 + +#endif /* _MCUCONF_H_ */ diff --git a/keyboards/handwired/onekey/teensy_lc/readme.md b/keyboards/handwired/onekey/teensy_lc/readme.md new file mode 100644 index 000000000..676d794d8 --- /dev/null +++ b/keyboards/handwired/onekey/teensy_lc/readme.md @@ -0,0 +1,40 @@ +# Teensy LC onekey + +To trigger keypress, short together pins *D5* and *B2* (marked on the PCB as *20* and *19*). + +## Hardware + +### Pins +When setting matrix pins, you need to use the MCU definitions instead of what is printed on the PCB. Sourced from <https://www.pjrc.com/teensy/schematic_lc.gif>. The following table can be used to convert between the two. + +| PCB | MCU | Notes | +|------- |-----|-------| +| 0 | B16 | | +| 1 | B17 | | +| 2 | D0 | | +| 3 | A1 | | +| 4 | A2 | | +| 5 | D7 | | +| 6 | D4 | | +| 7 | D2 | | +| 8 | D3 | | +| 9 | C3 | | +| 10 | C4 | | +| 11 | C6 | | +| 12 | C7 | | +| 13/LED | C5 | | +| 14/A0 | D1 | | +| 15/A1 | C0 | | +| 16/A2 | B0 | | +| 17/A3 | B1 | | +| 18/A4 | B3 | | +| 19/A5 | B2 | | +| 20/A6 | D5 | | +| 21/A7 | D6 | | +| 22/A8 | C1 | | +| 23/A9 | C2 | | +| 24/A10 | E2 | | +| 25/A11 | E21 | *[1]* | +| 26/A12 | E30 | *[1]* | + +*[1]* - Currently not configured and may require extra work to implement. diff --git a/keyboards/handwired/onekey/teensy_lc/rules.mk b/keyboards/handwired/onekey/teensy_lc/rules.mk new file mode 100644 index 000000000..7859f6d74 --- /dev/null +++ b/keyboards/handwired/onekey/teensy_lc/rules.mk @@ -0,0 +1,41 @@ +## chip/board settings +# - the next two should match the directories in +# <chibios>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES) +# - For Teensies, FAMILY = KINETIS and SERIES is either +# KL2x (LC) or K20x (3.0,3.1,3.2). +MCU_FAMILY = KINETIS +MCU_SERIES = KL2x + +# Linker script to use +# - it should exist either in <chibios>/os/common/ports/ARMCMx/compilers/GCC/ld/ +# or <this_dir>/ld/ +# - NOTE: a custom ld script is needed for EEPROM on Teensy LC +# - LDSCRIPT = +# - MKL26Z64 for Teensy LC +# - MK20DX128 for Teensy 3.0 +# - MK20DX256 for Teensy 3.1 and 3.2 +MCU_LDSCRIPT = MKL26Z64 + +# Startup code to use +# - it should exist in <chibios>/os/common/ports/ARMCMx/compilers/GCC/mk/ +# - STARTUP = +# - kl2x for Teensy LC +# - k20x5 for Teensy 3.0 +# - k20x7 for Teensy 3.1 and 3.2 +MCU_STARTUP = kl2x + +# Board: it should exist either in <chibios>/os/hal/boards/ +# or <this_dir>/boards +# - BOARD = +# - PJRC_TEENSY_LC for Teensy LC +# - PJRC_TEENSY_3 for Teensy 3.0 +# - PJRC_TEENSY_3_1 for Teensy 3.1 or 3.2 +BOARD = PJRC_TEENSY_LC + +# Cortex version +# Teensy LC is cortex-m0plus; Teensy 3.x are cortex-m4 +MCU = cortex-m0plus + +# ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7 +# I.e. 6 for Teensy LC; 7 for Teensy 3.x +ARMV = 6 diff --git a/keyboards/handwired/ortho5x13/config.h b/keyboards/handwired/ortho5x13/config.h index 1e2128b65..b3850a48a 100644 --- a/keyboards/handwired/ortho5x13/config.h +++ b/keyboards/handwired/ortho5x13/config.h @@ -54,7 +54,7 @@ along with this program. If not, see <http://www.gnu.org/licenses/>. // #define BACKLIGHT_LEVELS 3 /* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */ -#define DEBOUNCING_DELAY 5 +#define DEBOUNCE 5 /* define if matrix has ghost (lacks anti-ghosting diodes) */ //#define MATRIX_HAS_GHOST diff --git a/keyboards/handwired/pilcrow/config.h b/keyboards/handwired/pilcrow/config.h index 8f562de3b..439686ae6 100644 --- a/keyboards/handwired/pilcrow/config.h +++ b/keyboards/handwired/pilcrow/config.h @@ -54,7 +54,7 @@ along with this program. If not, see <http://www.gnu.org/licenses/>. // #define BACKLIGHT_LEVELS 3 /* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */ -#define DEBOUNCING_DELAY 5 +#define DEBOUNCE 5 /* define if matrix has ghost (lacks anti-ghosting diodes) */ //#define MATRIX_HAS_GHOST diff --git a/keyboards/handwired/prime_exl/config.h b/keyboards/handwired/prime_exl/config.h index 3201a8247..a2962c074 100644 --- a/keyboards/handwired/prime_exl/config.h +++ b/keyboards/handwired/prime_exl/config.h @@ -43,7 +43,7 @@ along with this program. If not, see <http://www.gnu.org/licenses/>. #define BACKLIGHT_LEVELS 5 /* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */ -#define DEBOUNCING_DELAY 5 +#define DEBOUNCE 5 /* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ #define LOCKING_SUPPORT_ENABLE diff --git a/keyboards/handwired/promethium/config.h b/keyboards/handwired/promethium/config.h index b5a0a7f4b..f05273d25 100644 --- a/keyboards/handwired/promethium/config.h +++ b/keyboards/handwired/promethium/config.h @@ -60,7 +60,7 @@ along with this program. If not, see <http://www.gnu.org/licenses/>. // #define BACKLIGHT_LEVELS 3 /* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */ -#define DEBOUNCING_DELAY 5 +#define DEBOUNCE 5 /* define if matrix has ghost (lacks anti-ghosting diodes) */ //#define MATRIX_HAS_GHOST diff --git a/keyboards/handwired/promethium/matrix.c b/keyboards/handwired/promethium/matrix.c index 0b4456e28..3b8e5af82 100644 --- a/keyboards/handwired/promethium/matrix.c +++ b/keyboards/handwired/promethium/matrix.c @@ -31,11 +31,11 @@ along with this program. If not, see <http://www.gnu.org/licenses/>. /* Set 0 if debouncing isn't needed */ -#ifndef DEBOUNCING_DELAY -# define DEBOUNCING_DELAY 5 +#ifndef DEBOUNCE +# define DEBOUNCE 5 #endif -#if (DEBOUNCING_DELAY > 0) +#if (DEBOUNCE > 0) static uint16_t debouncing_time; static bool debouncing = false; #endif @@ -128,7 +128,7 @@ uint8_t matrix_scan(void) { // Set row, read cols for (uint8_t current_row = 0; current_row < MATRIX_ROWS; current_row++) { -# if (DEBOUNCING_DELAY > 0) +# if (DEBOUNCE > 0) bool matrix_changed = read_cols_on_row(matrix_debouncing, current_row); if (matrix_changed) { @@ -142,8 +142,8 @@ uint8_t matrix_scan(void) } -# if (DEBOUNCING_DELAY > 0) - if (debouncing && (timer_elapsed(debouncing_time) > DEBOUNCING_DELAY)) { +# if (DEBOUNCE > 0) + if (debouncing && (timer_elapsed(debouncing_time) > DEBOUNCE)) { for (uint8_t i = 0; i < MATRIX_ROWS; i++) { matrix[i] = matrix_debouncing[i]; } @@ -157,7 +157,7 @@ uint8_t matrix_scan(void) bool matrix_is_modified(void) { -#if (DEBOUNCING_DELAY > 0) +#if (DEBOUNCE > 0) if (debouncing) return false; #endif return true; @@ -294,4 +294,3 @@ static void unselect_row(uint8_t row) static void unselect_rows(void) { } - diff --git a/keyboards/handwired/promethium/rgbsps.c b/keyboards/handwired/promethium/rgbsps.c index 84fac1ae1..f43987691 100644 --- a/keyboards/handwired/promethium/rgbsps.c +++ b/keyboards/handwired/promethium/rgbsps.c @@ -1,7 +1,7 @@ #include "ws2812.h" #include "rgbsps.h" -struct cRGB led[RGBSPS_NUM]; +cRGB led[RGBSPS_NUM]; void rgbsps_set(uint8_t index, uint8_t r, uint8_t g, uint8_t b) { led[index].r = r; diff --git a/keyboards/handwired/promethium/rules.mk b/keyboards/handwired/promethium/rules.mk index 21328b7f8..dab92e52c 100644 --- a/keyboards/handwired/promethium/rules.mk +++ b/keyboards/handwired/promethium/rules.mk @@ -47,7 +47,7 @@ OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT OPT_DEFS += -DBOOTLOADER_SIZE=4096 # Build Options -# change to "no" to disable the options, or define them in the Makefile in +# change to "no" to disable the options, or define them in the Makefile in # the appropriate keymap folder that will get included automatically # BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000) @@ -62,7 +62,7 @@ AUDIO_ENABLE = no # Audio output on port C6 UNICODE_ENABLE = no # Unicode UNICODEMAP_ENABLE = yes BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID -RGBLIGHT_ENABLE = no # Enable WS2812 RGB underlight. +RGBLIGHT_ENABLE = no # Enable WS2812 RGB underlight. PS2_MOUSE_ENABLE = yes PS2_USE_INT = yes API_SYSEX_ENABLE = no @@ -76,3 +76,5 @@ SRC += ws2812.c SRC += rgbsps.c SRC += analog.c SRC += matrix.c + +LINK_TIME_OPTIMIZATION_ENABLE = yes diff --git a/keyboards/handwired/pteron/config.h b/keyboards/handwired/pteron/config.h index d0b074c68..56921b020 100644 --- a/keyboards/handwired/pteron/config.h +++ b/keyboards/handwired/pteron/config.h @@ -23,7 +23,7 @@ #define DIODE_DIRECTION ROW2COL /* Set 0 if debouncing isn't needed */ -#define DEBOUNCING_DELAY 5 // 5 is default +#define DEBOUNCE 5 // 5 is default /* prevent stuck modifiers */ #define PREVENT_STUCK_MODIFIERS diff --git a/keyboards/handwired/qc60/config.h b/keyboards/handwired/qc60/config.h index aad1d64a0..0c8f8f007 100644 --- a/keyboards/handwired/qc60/config.h +++ b/keyboards/handwired/qc60/config.h @@ -16,7 +16,7 @@ #define MATRIX_COLS 8 /* Set 0 if debouncing isn't needed */ -#define DEBOUNCING_DELAY 5 +#define DEBOUNCE 5 /* serial.c configuration for split keyboard */ #define SOFT_SERIAL_PIN D0 diff --git a/keyboards/handwired/reddot/config.h b/keyboards/handwired/reddot/config.h index 82fe01863..4d908041b 100755 --- a/keyboards/handwired/reddot/config.h +++ b/keyboards/handwired/reddot/config.h @@ -54,7 +54,7 @@ along with this program. If not, see <http://www.gnu.org/licenses/>. // #define BACKLIGHT_LEVELS 3 /* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */ -#define DEBOUNCING_DELAY 5 +#define DEBOUNCE 5 /* define if matrix has ghost (lacks anti-ghosting diodes) */ //#define MATRIX_HAS_GHOST diff --git a/keyboards/handwired/retro_refit/config.h b/keyboards/handwired/retro_refit/config.h index 34def3815..1d4f1e075 100644 --- a/keyboards/handwired/retro_refit/config.h +++ b/keyboards/handwired/retro_refit/config.h @@ -47,7 +47,7 @@ along with this program. If not, see <http://www.gnu.org/licenses/>. #define BACKLIGHT_LEVELS 0 /* Set 0 if debouncing isn't needed */ -#define DEBOUNCING_DELAY 5 +#define DEBOUNCE 5 /* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ #define LOCKING_SUPPORT_ENABLE diff --git a/keyboards/handwired/space_oddity/config.h b/keyboards/handwired/space_oddity/config.h index 832216423..09975cfc8 100644 --- a/keyboards/handwired/space_oddity/config.h +++ b/keyboards/handwired/space_oddity/config.h @@ -35,7 +35,7 @@ #endif /* Set 0 if debouncing isn't needed */ -#define DEBOUNCING_DELAY 5 +#define DEBOUNCE 5 /* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ #define LOCKING_SUPPORT_ENABLE diff --git a/keyboards/handwired/splittest/config.h b/keyboards/handwired/splittest/config.h index 9e4fb38ca..a502d1238 100644 --- a/keyboards/handwired/splittest/config.h +++ b/keyboards/handwired/splittest/config.h @@ -43,7 +43,7 @@ along with this program. If not, see <http://www.gnu.org/licenses/>. //#define MATRIX_HAS_GHOST /* Set 0 if debouncing isn't needed */ -#define DEBOUNCING_DELAY 5 +#define DEBOUNCE 5 /* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ #define LOCKING_SUPPORT_ENABLE diff --git a/keyboards/handwired/tennie/config.h b/keyboards/handwired/tennie/config.h index b50886cdc..20795b048 100644 --- a/keyboards/handwired/tennie/config.h +++ b/keyboards/handwired/tennie/config.h @@ -80,7 +80,7 @@ along with this program. If not, see <http://www.gnu.org/licenses/>. #endif /* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */ -#define DEBOUNCING_DELAY 5 +#define DEBOUNCE 5 /* define if matrix has ghost (lacks anti-ghosting diodes) */ //#define MATRIX_HAS_GHOST diff --git a/keyboards/handwired/terminus_mini/config.h b/keyboards/handwired/terminus_mini/config.h index e1b5daccd..a5a6736ba 100644 --- a/keyboards/handwired/terminus_mini/config.h +++ b/keyboards/handwired/terminus_mini/config.h @@ -60,7 +60,7 @@ along with this program. If not, see <http://www.gnu.org/licenses/>. #define TAPPING_TERM 150 //reduce time required to register a held key /* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */ -#define DEBOUNCING_DELAY 5 +#define DEBOUNCE 5 /* define if matrix has ghost (lacks anti-ghosting diodes) */ //#define MATRIX_HAS_GHOST diff --git a/keyboards/handwired/trackpoint/config.h b/keyboards/handwired/trackpoint/config.h index cecb6a509..a1c12efb0 100644 --- a/keyboards/handwired/trackpoint/config.h +++ b/keyboards/handwired/trackpoint/config.h @@ -61,7 +61,7 @@ /* COL2ROW or ROW2COL */ #define DIODE_DIRECTION COL2ROW -#define DEBOUNCING_DELAY 5 +#define DEBOUNCE 5 #define LOCKING_SUPPORT_ENABLE #define LOCKING_RESYNC_ENABLE diff --git a/keyboards/handwired/tradestation/config.h b/keyboards/handwired/tradestation/config.h index 22650d2f1..33c87548f 100644 --- a/keyboards/handwired/tradestation/config.h +++ b/keyboards/handwired/tradestation/config.h @@ -29,7 +29,7 @@ #endif /* Set 0 if debouncing isn't needed */ -#define DEBOUNCING_DELAY 5 +#define DEBOUNCE 5 /* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ #define LOCKING_SUPPORT_ENABLE diff --git a/keyboards/handwired/traveller/config.h b/keyboards/handwired/traveller/config.h index ccf214736..3812ec61f 100644 --- a/keyboards/handwired/traveller/config.h +++ b/keyboards/handwired/traveller/config.h @@ -63,7 +63,7 @@ along with this program. If not, see <http://www.gnu.org/licenses/>. // #define BACKLIGHT_LEVELS 3 /* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */ -#define DEBOUNCING_DELAY 5 +#define DEBOUNCE 5 /* define if matrix has ghost (lacks anti-ghosting diodes) */ //#define MATRIX_HAS_GHOST diff --git a/keyboards/handwired/tritium_numpad/config.h b/keyboards/handwired/tritium_numpad/config.h new file mode 100644 index 000000000..83333c0fb --- /dev/null +++ b/keyboards/handwired/tritium_numpad/config.h @@ -0,0 +1,83 @@ +/* +Copyright 2012 Jun Wako <wakojun@gmail.com> + +This program is free software: you can redistribute it and/or modify +it under the terms of the GNU General Public License as published by +the Free Software Foundation, either version 2 of the License, or +(at your option) any later version. + +This program is distributed in the hope that it will be useful, +but WITHOUT ANY WARRANTY; without even the implied warranty of +MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +GNU General Public License for more details. + +You should have received a copy of the GNU General Public License +along with this program. If not, see <http://www.gnu.org/licenses/>. +*/ + +#pragma once + +#include "config_common.h" + +/* USB Device descriptor parameter */ +#define VENDOR_ID 0xFEED +#define PRODUCT_ID 0x6060 +#define DEVICE_VER 0x0003 +#define MANUFACTURER Handwired +#define PRODUCT Tritium Numpad +#define DESCRIPTION QMK keyboard firmware for handwired numpad + +/* key matrix size */ +#define MATRIX_ROWS 6 +#define MATRIX_COLS 4 + +// ROWS: Top to bottom, COLS: Left to right + +#define MATRIX_ROW_PINS { D1, D0, D4, C6, D7, E6 } +#define MATRIX_COL_PINS { F4, F6, B1, B2 } +#define UNUSED_PINS + +#define BACKLIGHT_PIN B6 + +/* COL2ROW or ROW2COL */ +#define DIODE_DIRECTION COL2ROW + +/* define if matrix has ghost */ +//#define MATRIX_HAS_GHOST + +/* Set 0 if debouncing isn't needed */ +#define DEBOUNCE 5 + +/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ +#define LOCKING_SUPPORT_ENABLE +/* Locking resynchronize hack */ +#define LOCKING_RESYNC_ENABLE + +/* Backlight configuration + */ +#define BACKLIGHT_LEVELS 4 + +/* Underlight configuration + */ + +#define RGB_DI_PIN D2 +#define RGBLED_NUM 4 // Number of LEDs + +/* + * Feature disable options + * These options are also useful to firmware size reduction. + */ + +/* disable debug print */ +//#define NO_DEBUG + +/* disable print */ +//#define NO_PRINT + +/* disable action features */ +//#define NO_ACTION_LAYER +//#define NO_ACTION_TAPPING +//#define NO_ACTION_ONESHOT +//#define NO_ACTION_MACRO +//#define NO_ACTION_FUNCTION + diff --git a/keyboards/handwired/tritium_numpad/info.json b/keyboards/handwired/tritium_numpad/info.json new file mode 100644 index 000000000..bc10efc82 --- /dev/null +++ b/keyboards/handwired/tritium_numpad/info.json @@ -0,0 +1,21 @@ +{ + "keyboard_name": "Tritium_numpad", + "url": "https://www.thingiverse.com/thing:2855938", + "maintainer": "qmk", + "width": 4, + "height": 6, + "layouts": { + "LAYOUT_numpad_6x4": { + "key_count": 21, + "layout": [{"label":"k00", "x":0, "y":0}, {"label":"k01", "x":1, "y":0}, {"label":"k02", "x":2, "y":0}, {"label":"k03", "x":3, "y":0}, {"label":"k10", "x":0, "y":1}, {"label":"k11", "x":1, "y":1}, {"label":"k12", "x":2, "y":1}, {"label":"k13", "x":3, "y":1}, {"label":"k20", "x":0, "y":2}, {"label":"k21", "x":1, "y":2}, {"label":"k22", "x":2, "y":2}, {"label":"k30", "x":0, "y":3}, {"label":"k31", "x":1, "y":3}, {"label":"k32", "x":2, "y":3}, {"label":"k23", "x":3, "y":2, "h":2}, {"label":"k40", "x":0, "y":4}, {"label":"k41", "x":1, "y":4}, {"label":"k42", "x":2, "y":4}, {"label":"k50", "x":0, "y":5, "w":2}, {"label":"k52", "x":2, "y":5}, {"label":"k43", "x":3, "y":4, "h":2}] + }, + "LAYOUT_nontra_6x4": { + "key_count": 22, + "layout": [{"label":"k00", "x":0, "y":0}, {"label":"k01", "x":1, "y":0}, {"label":"k02", "x":2, "y":0}, {"label":"k03", "x":3, "y":0}, {"label":"k10", "x":0, "y":1}, {"label":"k11", "x":1, "y":1}, {"label":"k12", "x":2, "y":1}, {"label":"k13", "x":3, "y":1}, {"label":"k20", "x":0, "y":2}, {"label":"k21", "x":1, "y":2}, {"label":"k22", "x":2, "y":2}, {"label":"k23", "x":3, "y":2, "h":2}, {"label":"k30", "x":0, "y":3}, {"label":"k31", "x":1, "y":3}, {"label":"k32", "x":2, "y":3}, {"label":"k40", "x":0, "y":4}, {"label":"k41", "x":1, "y":4}, {"label":"k42", "x":2, "y":4}, {"label":"k43", "x":3, "y":4, "h":2}, {"label":"k50", "x":0, "y":5}, {"label":"k51", "x":1, "y":5}, {"label":"k52", "x":2, "y":5}] + }, + "LAYOUT_ortho_6x4": { + "key_count": 24, + "layout": [{"label":"k00", "x":0, "y":0}, {"label":"k01", "x":1, "y":0}, {"label":"k02", "x":2, "y":0}, {"label":"k03", "x":3, "y":0}, {"label":"k10", "x":0, "y":1}, {"label":"k11", "x":1, "y":1}, {"label":"k12", "x":2, "y":1}, {"label":"k13", "x":3, "y":1}, {"label":"k20", "x":0, "y":2}, {"label":"k21", "x":1, "y":2}, {"label":"k22", "x":2, "y":2}, {"label":"k23", "x":3, "y":2}, {"label":"k30", "x":0, "y":3}, {"label":"k31", "x":1, "y":3}, {"label":"k32", "x":2, "y":3}, {"label":"k33", "x":3, "y":3}, {"label":"k40", "x":0, "y":4}, {"label":"k41", "x":1, "y":4}, {"label":"k42", "x":2, "y":4}, {"label":"k43", "x":3, "y":4}, {"label":"k50", "x":0, "y":5}, {"label":"k51", "x":1, "y":5}, {"label":"k52", "x":2, "y":5}, {"label":"k53", "x":3, "y":5}] + } + } +} diff --git a/keyboards/handwired/tritium_numpad/keymaps/blu/keymap.c b/keyboards/handwired/tritium_numpad/keymaps/blu/keymap.c new file mode 100644 index 000000000..958c17e42 --- /dev/null +++ b/keyboards/handwired/tritium_numpad/keymaps/blu/keymap.c @@ -0,0 +1,40 @@ +#include QMK_KEYBOARD_H + +void keyboard_pre_init_user(void) +{ + // Set layer LED as an output + setPinOutput(B0); +} + +uint32_t layer_state_set_user(uint32_t state) +{ + // Switch layer LED accordingly + switch (biton32(state)) { + case 0: + writePinHigh(B0); + break; + case 1: + writePinLow(B0); + break; + } + return state; +} + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { + [0] = LAYOUT_ortho_6x4( + KC_NLCK, KC_PSLS, KC_PAST, KC_PMNS, + KC_P7, KC_P8, KC_P9, KC_PPLS, + KC_P4, KC_P5, KC_P6, KC_BSPC, + KC_P1, KC_P2, KC_P3, KC_PENT, + KC_P0, KC_UP, KC_PDOT, TT(1), + KC_LEFT, KC_DOWN, KC_RGHT, BL_STEP + ), + [1] = LAYOUT_ortho_6x4( + KC_NO, KC_NO, KC_NO, KC_NO, + KC_NO, KC_K, KC_NO, KC_NO, + KC_H, KC_NO, KC_L, KC_NO, + KC_NO, KC_J, KC_NO, KC_NO, + KC_LSFT, KC_Z, KC_X, KC_TRNS, + KC_NO, KC_NO, KC_NO, KC_NO + ) +}; diff --git a/keyboards/handwired/tritium_numpad/keymaps/blu/layers.json b/keyboards/handwired/tritium_numpad/keymaps/blu/layers.json new file mode 100644 index 000000000..5335c651f --- /dev/null +++ b/keyboards/handwired/tritium_numpad/keymaps/blu/layers.json @@ -0,0 +1 @@ +[["KC_NLCK", "KC_PSLS", "KC_PAST", "KC_PMNS", "KC_P7", "KC_P8", "KC_P9", "KC_PPLS", "KC_P4", "KC_P5", "KC_P6", "KC_BSPC", "KC_P1", "KC_P2", "KC_P3", "KC_PENT", "KC_P0", "KC_UP", "KC_PDOT", "TT(1)", "KC_LEFT", "KC_DOWN", "KC_RGHT", "BL_STEP"], ["KC_NO", "KC_NO", "KC_NO", "KC_NO", "KC_NO", "KC_K", "KC_NO", "KC_NO", "KC_H", "KC_NO", "KC_L", "KC_NO", "KC_NO", "KC_J", "KC_NO", "KC_NO", "KC_LSFT", "KC_Z", "KC_X", "KC_TRNS", "KC_NO", "KC_NO", "KC_NO", "KC_NO"]]
\ No newline at end of file diff --git a/keyboards/handwired/tritium_numpad/keymaps/blu/readme.md b/keyboards/handwired/tritium_numpad/keymaps/blu/readme.md new file mode 100644 index 000000000..fd07b155f --- /dev/null +++ b/keyboards/handwired/tritium_numpad/keymaps/blu/readme.md @@ -0,0 +1,13 @@ +# Generated Keymap Layout + +This layout was generated by the QMK API. You can find the JSON data used to +generate this keymap in the file layers.json. + +To make use of this file you will need follow the following steps: + +* Download or Clone QMK Firmware: <https://github.com/qmk/qmk_firmware/> +* Extract QMK Firmware to a location on your hard drive +* Copy this folder into %s +* You are now ready to compile or use your keymap with the source + +More information can be found in the QMK docs: <https://docs.qmk.fm>
\ No newline at end of file diff --git a/keyboards/handwired/tritium_numpad/keymaps/default/keymap.c b/keyboards/handwired/tritium_numpad/keymaps/default/keymap.c new file mode 100644 index 000000000..60430217b --- /dev/null +++ b/keyboards/handwired/tritium_numpad/keymaps/default/keymap.c @@ -0,0 +1,59 @@ +#include QMK_KEYBOARD_H + +// Each layer gets a name for readability, which is then used in the keymap matrix below. +// The underscores don't mean anything - you can have a layer called STUFF or any other name. +// Layer names don't all need to be of the same length, obviously, and you can also skip them +// entirely and just use numbers. +#define _BL 0 +#define _FL 1 + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { + /* Keymap _BL: (Base Layer) Default Layer + * ,-------------------. + * |Esc |TAB |BS | = | + * |----|----|----|----| + * | NL | / | * | - | + * |----|----|----|----| + * | 7 | 8 | 9 | | + * |----|----|----| + | + * | 4 | 5 | 6 | | + * |----|----|----|----| + * | 1 | 2 | 3 | | + * |----|----|----| En | + * | 0 |./FN| | + * `-------------------' + */ + + [_BL] = LAYOUT_numpad_6x4( + KC_ESC, KC_TAB, KC_BSPC, KC_PEQL, + KC_NLCK, KC_PSLS, KC_PAST, KC_PMNS, + KC_P7, KC_P8, KC_P9, + KC_P4, KC_P5, KC_P6, KC_PPLS, + KC_P1, KC_P2, KC_P3, + KC_P0, LT(_FL,KC_PDOT), KC_PENT + ), + + /* Keymap _FL: Function Layer + * ,-------------------. + * |Esc |TAB |BS | = | + * |----|----|----|----| + * | NL | / | * | - | + * |----|----|----|----| + * | 7 | 8 | 9 | | + * |----|----|----|RST | + * | 4 | 5 | 6 | | + * |----|----|----|----| + * | 1 | 2 | 3 | | + * |----|----|----| En | + * | 0 |./FN| | + * `-------------------' + */ + [_FL] = LAYOUT_numpad_6x4( + KC_ESC, KC_TAB, KC_BSPC, KC_PEQL, + KC_NLCK, KC_PSLS, KC_PAST, KC_PMNS, + KC_P7, KC_P8, KC_P9, + KC_P4, KC_P5, KC_P6, RESET, + KC_P1, KC_P2, KC_P3, + KC_P0, LT(_FL,KC_PDOT), KC_PENT + ), +}; diff --git a/keyboards/handwired/tritium_numpad/keymaps/max/keymap.c b/keyboards/handwired/tritium_numpad/keymaps/max/keymap.c new file mode 100644 index 000000000..bba5c43bb --- /dev/null +++ b/keyboards/handwired/tritium_numpad/keymaps/max/keymap.c @@ -0,0 +1,59 @@ +#include QMK_KEYBOARD_H + +// Each layer gets a name for readability, which is then used in the keymap matrix below. +// The underscores don't mean anything - you can have a layer called STUFF or any other name. +// Layer names don't all need to be of the same length, obviously, and you can also skip them +// entirely and just use numbers. +#define _BL 0 +#define _FL 1 + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { + /* Keymap _BL: (Base Layer) Default Layer + * ,-------------------. + * |Esc |Setp| - | = | + * |----|----|----|----| + * | F1 | F2 | F3 | F4 | + * |----|----|----|----| + * | 7 | 8 | 9 | - | + * |----|----|----|----| + * | 4 | 5 | 6 | LF | + * |----|----|----|----| + * | 1 | 2 | 3 | \ | + * |----|----|----|----| + * |Left|Down| Up |Rght| + * `-------------------' + */ + + [_BL] = LAYOUT_ortho_6x4( + KC_ESC, KC_TAB, KC_MINS,KC_EQL, + KC_F1, KC_F2, KC_F3, KC_F4, + KC_P7, KC_P8, KC_P9, KC_PMNS, + KC_P4, KC_P5, KC_P6, KC_PENT, + KC_P1, KC_P2, KC_P3, KC_BSLS, + KC_LEFT, KC_DOWN, KC_UP, KC_RIGHT + ), + + /* Keymap _FL: Function Layer + * ,-------------------. + * |Esc |TAB |BS | = | + * |----|----|----|----| + * | NL | / | * | - | + * |----|----|----|----| + * | 7 | 8 | 9 | | + * |----|----|----|RST | + * | 4 | 5 | 6 | | + * |----|----|----|----| + * | 1 | 2 | 3 | | + * |----|----|----| En | + * | 0 |./FN| | + * `-------------------' + */ + [_FL] = LAYOUT_ortho_6x4( + KC_ESC, KC_TAB, KC_BSPC, KC_PEQL, + KC_NLCK, KC_PSLS, KC_PAST, KC_PMNS, + KC_P7, KC_P8, KC_P9, RESET, + KC_P4, KC_P5, KC_P6, KC_PENT, + KC_P1, KC_P2, KC_P3, KC_PENT, + KC_LEFT, KC_DOWN, KC_UP, KC_RIGHT + ), +}; diff --git a/keyboards/handwired/tritium_numpad/keymaps/ortho_left/keymap.c b/keyboards/handwired/tritium_numpad/keymaps/ortho_left/keymap.c new file mode 100644 index 000000000..9d569f18a --- /dev/null +++ b/keyboards/handwired/tritium_numpad/keymaps/ortho_left/keymap.c @@ -0,0 +1,59 @@ +#include QMK_KEYBOARD_H + +// Each layer gets a name for readability, which is then used in the keymap matrix below. +// The underscores don't mean anything - you can have a layer called STUFF or any other name. +// Layer names don't all need to be of the same length, obviously, and you can also skip them +// entirely and just use numbers. +#define _BL 0 +#define _FL 1 + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { + /* Keymap _BL: (Base Layer) Default Layer + * ,-------------------. + * | T | G | B |Spac| + * |----|----|----|----| + * | R | F | V | Fn | + * |----|----|----|----| + * | E | D | C | OS | + * |----|----|----|----| + * | W | S | X | Alt| + * |----|----|----|----| + * | Q | A | Z | Ctl| + * |----|----|----|----| + * | Esc| Tab|Shft| Fn2| + * `-------------------' + */ + + [_BL] = LAYOUT_ortho_6x4( + KC_T, KC_G, KC_B, KC_SPACE, + KC_R, KC_F, KC_V, MO(1), + KC_E, KC_D, KC_C, KC_LGUI, + KC_W, KC_S, KC_X, KC_LALT, + KC_Q, KC_A, KC_Z, KC_LCTL, + KC_TAB, KC_ESC, KC_LSHIFT, MO(1) + ), + + /* Keymap _FL: Function Layer + * ,-------------------. + * | 5 | F5 | F11|Spac| + * |----|----|----|----| + * | 4 | F4 | F10| | + * |----|----|----|----| + * | 3 | F3 | F9 | OS | + * |----|----|----|----| + * | 2 | F2 | F8 | Alt| + * |----|----|----|----| + * | 1 | F1 | F7 | Ctl| + * |----|----|----|----| + * | ` | Del|Shft| | + * `-------------------' + */ + [_FL] = LAYOUT_ortho_6x4( + KC_5, KC_F5, KC_F11, _______, + KC_4, KC_F4, KC_F10, _______, + KC_3, KC_F3, KC_F9, _______, + KC_2, KC_F2, KC_F8, _______, + KC_1, KC_F1, KC_F7, _______, + KC_GRV,KC_DEL, _______, _______ + ), +}; diff --git a/keyboards/handwired/tritium_numpad/keymaps/ortho_right/keymap.c b/keyboards/handwired/tritium_numpad/keymaps/ortho_right/keymap.c new file mode 100644 index 000000000..0dc2f81bc --- /dev/null +++ b/keyboards/handwired/tritium_numpad/keymaps/ortho_right/keymap.c @@ -0,0 +1,61 @@ +#include QMK_KEYBOARD_H + +#ifdef RGBLIGHT_ENABLE +#endif + +// Each layer gets a name for readability, which is then used in the keymap matrix below. +// The underscores don't mean anything - you can have a layer called STUFF or any other name. +// Layer names don't all need to be of the same length, obviously, and you can also skip them +// entirely and just use numbers. +#define _BL 0 +#define _FL 1 + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { + /* Keymap _BL: (Base Layer) Default Layer + * ,-------------------. + * |Spac| N | H | Y | + * |----|----|----|----| + * | Fn | M | J | U | + * |----|----|----|----| + * |Left| , | K | I | + * |----|----|----|----| + * |Down| . | L | O | + * |----|----|----|----| + * | Up | / | ; | P | + * |----|----|----|----| + * |Rght| Ret| " |Bspc| + * `-------------------' + */ + [_BL] = LAYOUT_ortho_6x4( + KC_SPACE, KC_N, KC_H, KC_Y, + MO(1), KC_M, KC_J, KC_U, + KC_LEFT, KC_COMM, KC_K, KC_I, + KC_DOWN, KC_DOT, KC_L, KC_O, + KC_UP, KC_SLASH, KC_SCLN, KC_P, + KC_RIGHT, KC_ENT, KC_QUOT, KC_BSPC + ), + + /* Keymap _FL: Function Layer + * ,-------------------. + * |Esc | F12| F6 | 6 | + * |----|----|----|----| + * | NL | M | - | 7 | + * |----|----|----|----| + * |Left| , | = | 8 | + * |----|----|----|----| + * |Down| . | [ | 9 | + * |----|----|----|----| + * | Up | / | ] | 0 | + * |----|----|----|----| + * |Rght| Ret| \ | Del| + * `-------------------' + */ + [_FL] = LAYOUT_ortho_6x4( + _______, KC_F12, KC_F6, KC_6, + _______, _______, KC_MINS, KC_7, + _______, _______, KC_EQL, KC_8, + _______, _______, KC_LBRC, KC_9, + _______, _______, KC_RBRC, KC_0, + _______, _______, KC_BSLS, KC_DEL + ), +}; diff --git a/keyboards/handwired/tritium_numpad/readme.md b/keyboards/handwired/tritium_numpad/readme.md new file mode 100644 index 000000000..21acfe759 --- /dev/null +++ b/keyboards/handwired/tritium_numpad/readme.md @@ -0,0 +1,28 @@ +Tritium Numpad +=== + +Keyboard Maintainer: QMK Community +Hardware Supported: Handwired 6x4 numpads using promicro controller +Hardware Availability: https://www.thingiverse.com/thing:2855938 + +Wiring is accomplished on the Pro Micro board using the following pins as rows: +* D2 : Row 1 +* D3 : Row 2 +* D4 : Row 3 +* D5 : Row 4 +* D6 : Row 5 +* D7 : Row 6 + +and the following pins as columns: +* A3 : Col 1 +* A1 : Col 2 +* D15 : Col 3 +* D16 : Col 4 + +Make example for this keyboard (after setting up your build environment): + + make tritium_numpad:default + +Bootmagic is enabled. Press the key at 0,0 (usually escape or numlock in the top left corner) while plugging the keyboard in to jump to bootloader. + +See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs). diff --git a/keyboards/handwired/tritium_numpad/rules.mk b/keyboards/handwired/tritium_numpad/rules.mk new file mode 100644 index 000000000..c990a6ab1 --- /dev/null +++ b/keyboards/handwired/tritium_numpad/rules.mk @@ -0,0 +1,61 @@ +# MCU name +MCU = atmega32u4 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Bootloader +# This definition is optional, and if your keyboard supports multiple bootloaders of +# different sizes, comment this out, and the correct address will be loaded +# automatically (+60). See bootloader.mk for all options. +BOOTLOADER = caterina + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + +# Build Options +# comment out to disable the options. +# +BOOTMAGIC_ENABLE = lite # Key at 0,0 makes the keyboard go into bootloader(+1000) +MOUSEKEY_ENABLE = no # Mouse keys(+4700) +EXTRAKEY_ENABLE = yes # Audio control and System control(+450) +CONSOLE_ENABLE = yes # Console for debug(+400) +COMMAND_ENABLE = yes # Commands for debug and configuration +NKRO_ENABLE = yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +RGBLIGHT_ENABLE = no # Enable keyboard underlight functionality (+4870) +BACKLIGHT_ENABLE = yes # Enable keyboard backlight functionality (+1150) +MIDI_ENABLE = no # MIDI controls +AUDIO_ENABLE = no +UNICODE_ENABLE = no # Unicode +BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID + +LAYOUTS = numpad_6x4 ortho_6x4 nontra_6x4 diff --git a/keyboards/handwired/tritium_numpad/tritium_numpad.c b/keyboards/handwired/tritium_numpad/tritium_numpad.c new file mode 100644 index 000000000..7193a934d --- /dev/null +++ b/keyboards/handwired/tritium_numpad/tritium_numpad.c @@ -0,0 +1,29 @@ +#include "tritium_numpad.h" +#include "led.h" + +void keyboard_pre_init_kb(void) { + // put your keyboard start-up code here + // runs once when the firmware starts up + keyboard_pre_init_user(); + led_init_ports(); +}; + +void matrix_scan_kb(void) { + // put your looping keyboard code here + // runs every cycle (a lot) + matrix_scan_user(); +}; + +void led_init_ports(void) { + // * Set our LED pins as output + // Numlock LED + setPinOutput(D5); +} + +void led_set_kb(uint8_t usb_led) { + if (IS_LED_ON(usb_led, USB_LED_NUM_LOCK)) { + writePinLow(D5); + } else { + writePinHigh(D5); + } +} diff --git a/keyboards/handwired/tritium_numpad/tritium_numpad.h b/keyboards/handwired/tritium_numpad/tritium_numpad.h new file mode 100644 index 000000000..8d2e78329 --- /dev/null +++ b/keyboards/handwired/tritium_numpad/tritium_numpad.h @@ -0,0 +1,95 @@ +#pragma once + +#include "quantum.h" + +// readability +#define XXX KC_NO + +/* matrix layout + * ,-------------------. + * | 00 | 01 | 02 | 03 | + * |----|----|----|----| + * | 10 | 11 | 12 | 13 | + * |----|----|----|----| + * | 20 | 21 | 22 | | + * |----|----|----| 23 | + * | 30 | 31 | 32 | | + * |----|----|----|----| + * | 40 | 41 | 42 | | + * |----|----|----| 43 | + * | 50 | 52 | | + * `-------------------' + */ +// The first section contains all of the arguments +// The second converts the arguments into a two-dimensional array +#define LAYOUT_numpad_6x4( \ + k00, k01, k02, k03, \ + k10, k11, k12, k13, \ + k20, k21, k22, \ + k30, k31, k32, k23, \ + k40, k41, k42, \ + k50, k52, k43 \ +) \ +{ \ + {k00, k01, k02, k03}, \ + {k10, k11, k12, k13}, \ + {k20, k21, k22, k23}, \ + {k30, k31, k32, XXX}, \ + {k40, k41, k42, k43}, \ + {k50, XXX, k52, XXX} \ +} + +/* matrix layout + * ,-------------------. + * | 00 | 01 | 02 | 03 | + * |----|----|----|----| + * | 10 | 11 | 12 | 13 | + * |----|----|----|----| + * | 20 | 21 | 22 | | + * |----|----|----| 23 | + * | 30 | 31 | 32 | | + * |----|----|----|----| + * | 40 | 41 | 42 | | + * |----|----|----| 43 | + * | 50 | 51 | 52 | | + * `-------------------' + */ +// The first section contains all of the arguments +// The second converts the arguments into a two-dimensional array +#define LAYOUT_nontra_6x4( \ + k00, k01, k02, k03, \ + k10, k11, k12, k13, \ + k20, k21, k22, \ + k30, k31, k32, k23, \ + k40, k41, k42, \ + k50, k51, k52, k43 \ +) \ +{ \ + {k00, k01, k02, k03}, \ + {k10, k11, k12, k13}, \ + {k20, k21, k22, k23}, \ + {k30, k31, k32, xxx}, \ + {k40, k41, k42, k43}, \ + {k50, k51, k52, xxx} \ +} + +#define LAYOUT_ortho_6x4( \ + k00, k01, k02, k03, \ + k10, k11, k12, k13, \ + k20, k21, k22, k23, \ + k30, k31, k32, k33, \ + k40, k41, k42, k43, \ + k50, k51, k52, k53 \ +) \ +{ \ + {k00, k01, k02, k03}, \ + {k10, k11, k12, k13}, \ + {k20, k21, k22, k23}, \ + {k30, k31, k32, k33}, \ + {k40, k41, k42, k43}, \ + {k50, k51, k52, k53} \ +} + +void keyboard_pre_init_user(void); +void matrix_scan_user(void); + diff --git a/keyboards/handwired/woodpad/config.h b/keyboards/handwired/woodpad/config.h index 77be4a0d9..d08c47387 100644 --- a/keyboards/handwired/woodpad/config.h +++ b/keyboards/handwired/woodpad/config.h @@ -54,7 +54,7 @@ along with this program. If not, see <http://www.gnu.org/licenses/>. // #define BACKLIGHT_LEVELS 3 /* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */ -#define DEBOUNCING_DELAY 5 +#define DEBOUNCE 5 /* define if matrix has ghost (lacks anti-ghosting diodes) */ //#define MATRIX_HAS_GHOST diff --git a/keyboards/handwired/wulkan/README.md b/keyboards/handwired/wulkan/README.md new file mode 100644 index 000000000..c6ea77389 --- /dev/null +++ b/keyboards/handwired/wulkan/README.md @@ -0,0 +1,14 @@ +# wulkan + +Handwired 40% keyboard build with Proton C. + +Keyboard Maintainer: [Napoleon Wulkan](https://github.com/wulkan) +Hardware Supported: Proton C +Hardware Availability: [OLKB.com](https://olkb.com) + + +Make example for this keyboard (after setting up your build environment): + + make handwired/wulkan:default:dfu-util + +See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs). diff --git a/keyboards/handwired/wulkan/config.h b/keyboards/handwired/wulkan/config.h new file mode 100644 index 000000000..4a9cbada7 --- /dev/null +++ b/keyboards/handwired/wulkan/config.h @@ -0,0 +1,23 @@ +#pragma once + +#include "config_common.h" + +/* USB Device descriptor parameter */ +#define VENDOR_ID 0xFEED +#define PRODUCT_ID 0x6060 +#define DEVICE_VER 0x0001 +#define MANUFACTURER Wulkan +#define PRODUCT Handwired48Keys +#define DESCRIPTION A compact ortholinear handwired keyboard + +/* key matrix size */ +#define MATRIX_ROWS 4 +#define MATRIX_COLS 12 + +#define MATRIX_ROW_PINS { B8, A0, A1, A2 } +#define MATRIX_COL_PINS { B13, B14, B15, B9, B7, B6, B5, B4, B3, B2, B1, B0 } + +/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */ +#define DEBOUNCE 5 + +#define FORCE_NKRO diff --git a/keyboards/handwired/wulkan/info.json b/keyboards/handwired/wulkan/info.json new file mode 100644 index 000000000..db292af3d --- /dev/null +++ b/keyboards/handwired/wulkan/info.json @@ -0,0 +1,13 @@ +{ + "keyboard_name": "wulkan", + "url": "", + "maintainer": "Napoleon Wulkan", + "width": 12, + "height": 4, + "layouts": { + "LAYOUT_ortho_4x12": { + "key_count": 48, + "layout": [{"x":0, "y":0}, {"x":1, "y":0}, {"x":2, "y":0}, {"x":3, "y":0}, {"x":4, "y":0}, {"x":5, "y":0}, {"x":6, "y":0}, {"x":7, "y":0}, {"x":8, "y":0}, {"x":9, "y":0}, {"x":10, "y":0}, {"x":11, "y":0}, {"x":0, "y":1}, {"x":1, "y":1}, {"x":2, "y":1}, {"x":3, "y":1}, {"x":4, "y":1}, {"x":5, "y":1}, {"x":6, "y":1}, {"x":7, "y":1}, {"x":8, "y":1}, {"x":9, "y":1}, {"x":10, "y":1}, {"x":11, "y":1}, {"x":0, "y":2}, {"x":1, "y":2}, {"x":2, "y":2}, {"x":3, "y":2}, {"x":4, "y":2}, {"x":5, "y":2}, {"x":6, "y":2}, {"x":7, "y":2}, {"x":8, "y":2}, {"x":9, "y":2}, {"x":10, "y":2}, {"x":11, "y":2}, {"x":0, "y":3}, {"x":1, "y":3}, {"x":2, "y":3}, {"x":3, "y":3}, {"x":4, "y":3}, {"x":5, "y":3}, {"x":6, "y":3}, {"x":7, "y":3}, {"x":8, "y":3}, {"x":9, "y":3}, {"x":10, "y":3}, {"x":11, "y":3}] + } + } + } diff --git a/keyboards/handwired/wulkan/keymaps/default/keymap.c b/keyboards/handwired/wulkan/keymaps/default/keymap.c new file mode 100644 index 000000000..5134fb000 --- /dev/null +++ b/keyboards/handwired/wulkan/keymaps/default/keymap.c @@ -0,0 +1,111 @@ +#include QMK_KEYBOARD_H + +enum layers { + _QWERTY, + _LOWER, + _RAISE, + _ADJUST, +}; + +enum unicode_names { + SE_AA_HIGH, + SE_AE_HIGH, + SE_OE_HIGH, + SE_AA_LOW, + SE_AE_LOW, + SE_OE_LOW, +}; + +const uint32_t PROGMEM unicode_map[] = { + [SE_AA_HIGH] = 0x00C5, + [SE_AE_HIGH] = 0x00C4, + [SE_OE_HIGH] = 0x00D6, + [SE_AA_LOW] = 0x00E5, + [SE_AE_LOW] = 0x00E4, + [SE_OE_LOW] = 0x00F6, +}; + +#define LOWER MO(_LOWER) +#define RAISE MO(_RAISE) + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { +/* Qwerty + * ,-----------------------------------------------------------------------------------. + * | Tab | Q | W | E | R | T | Y | U | I | O | P | Bksp | + * |------+------+------+------+------+-------------+------+------+------+------+------| + * | Esc | A | S | D | F | G | H | J | K | L | ; | " | + * |------+------+------+------+------+------|------+------+------+------+------+------| + * | Shift| Z | X | C | V | B | N | M | , | . | / |Shift | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | | Ctrl | Alt | GUI |Lower |Enter |Space |Raise | Left | Down | Up |Right | + * `-----------------------------------------------------------------------------------' + */ +[_QWERTY] = LAYOUT_ortho_4x12( + KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_BSPC, + KC_ESC, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT, + KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, KC_RSFT, + _______, KC_LCTL, KC_LALT, KC_LGUI, LOWER, KC_ENT, KC_SPC, RAISE, KC_LEFT, KC_DOWN, KC_UP, KC_RGHT +), + +/* Lower + * ,-----------------------------------------------------------------------------------. + * | ~ | ! | @ | # | $ | % | ^ | & | * | ( | ) | Bksp | + * |------+------+------+------+------+-------------+------+------+------+------+------| + * | Del | F1 | F2 | F3 | F4 | F5 | F6 | _ | + | { | } | | | + * |------+------+------+------+------+------|------+------+------+------+------+------| + * | | F7 | F8 | F9 | F10 | F11 | F12 |ISO ~ |ISO | | | | | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | | | | | | | | | Next | Vol- | Vol+ | Play | + * `-----------------------------------------------------------------------------------' + */ +[_LOWER] = LAYOUT_ortho_4x12( + KC_TILD, KC_EXLM, KC_AT, KC_HASH, KC_DLR, KC_PERC, KC_CIRC, KC_AMPR, KC_ASTR, KC_LPRN, KC_RPRN, KC_BSPC, + KC_DEL, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_UNDS, KC_PLUS, KC_LCBR, KC_RCBR, KC_PIPE, + _______, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, S(KC_NUHS), S(KC_NUBS), _______, _______, _______, + _______, _______, _______, _______, _______, _______, _______, _______, KC_MNXT, KC_VOLD, KC_VOLU, KC_MPLY +), + +/* Raise + * ,-----------------------------------------------------------------------------------. + * | ` | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 0 | Del | + * |------+------+------+------+------+-------------+------+------+------+------+------| + * | Del | F1 | F2 | F3 | F4 | F5 | F6 | - | = | [ | ] | \ | + * |------+------+------+------+------+------|------+------+------+------+------+------| + * | | F7 | F8 | F9 | F10 | F11 | F12 |ISO # |ISO / | | | | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | | | | | | | | | Next | Vol- | Vol+ | Play | + * `-----------------------------------------------------------------------------------' + */ +[_RAISE] = LAYOUT_ortho_4x12( + KC_GRV, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_DEL, + KC_DEL, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_MINS, KC_EQL, KC_LBRC, KC_RBRC, KC_BSLS, + _______, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, KC_NUHS, KC_NUBS, _______, _______, _______, + _______, _______, _______, _______, _______, _______, _______, _______, KC_MNXT, KC_VOLD, KC_VOLU, KC_MPLY +), + +/* Adjust (Lower + Raise) + * ,-----------------------------------------------------------------------------------. + * | | Reset| | | | | | | | | Å | Del | + * |------+------+------+------+------+-------------+------+------+------+------+------| + * | | | | | | | | | | Ö | Ä | | + * |------+------+------+------+------+------|------+------+------+------+------+------| + * | | | | | | | | | | | | | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | | | | | | | | | | | | | + * `-----------------------------------------------------------------------------------' + */ +[_ADJUST] = LAYOUT_ortho_4x12( + _______, RESET, _______, _______, KC_WH_U, _______, _______, KC_MS_U, _______, _______, XP(SE_AA_LOW, SE_AA_HIGH), KC_DEL, + _______, _______, _______, _______, KC_WH_D, _______, KC_MS_L, KC_MS_D, KC_MS_R, XP(SE_OE_LOW, SE_OE_HIGH), XP(SE_AE_LOW, SE_AE_HIGH), _______, + _______, KC_ACL0, KC_ACL1, KC_ACL2, _______, _______, KC_BTN1, _______, KC_BTN2, _______, _______, _______, + _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______ +) +}; + +uint32_t layer_state_set_user(uint32_t state) { + return update_tri_layer_state(state, _LOWER, _RAISE, _ADJUST); +} + +void eeconfig_init_user(void) { + set_unicode_input_mode(UC_LNX); +} diff --git a/keyboards/handwired/wulkan/keymaps/default/rules.mk b/keyboards/handwired/wulkan/keymaps/default/rules.mk new file mode 100644 index 000000000..502b2def7 --- /dev/null +++ b/keyboards/handwired/wulkan/keymaps/default/rules.mk @@ -0,0 +1 @@ +UNICODEMAP_ENABLE = yes diff --git a/keyboards/handwired/wulkan/rules.mk b/keyboards/handwired/wulkan/rules.mk new file mode 100644 index 000000000..3f881b7f1 --- /dev/null +++ b/keyboards/handwired/wulkan/rules.mk @@ -0,0 +1,22 @@ +MCU = STM32F303 + +# Build Options +# comment out to disable the options. +# +BACKLIGHT_ENABLE = no +BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration +MOUSEKEY_ENABLE = yes # Mouse keys +EXTRAKEY_ENABLE = yes # Audio control and System control +CONSOLE_ENABLE = no # Console for debug +COMMAND_ENABLE = no # Commands for debug and configuration +NKRO_ENABLE = yes # USB Nkey Rollover +AUDIO_ENABLE = no +RGBLIGHT_ENABLE = no +LAYOUTS = ortho_4x12 +MIDI_ENABLE = no # MIDI support (+2400 to 4200, depending on config) +UNICODE_ENABLE = no # Unicode +BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID +FAUXCLICKY_ENABLE = no # Use buzzer to emulate clicky switches +HD44780_ENABLE = no # Enable support for HD44780 based LCDs (+400) +NO_SUSPEND_POWER_DOWN = yes +UNICODEMAP_ENABLE = no diff --git a/keyboards/handwired/wulkan/wulkan.c b/keyboards/handwired/wulkan/wulkan.c new file mode 100644 index 000000000..5409fa5b5 --- /dev/null +++ b/keyboards/handwired/wulkan/wulkan.c @@ -0,0 +1,6 @@ +#include "wulkan.h" + +void matrix_init_kb(void) { + matrix_init_user(); +} + diff --git a/keyboards/handwired/wulkan/wulkan.h b/keyboards/handwired/wulkan/wulkan.h new file mode 100644 index 000000000..cb4882ac9 --- /dev/null +++ b/keyboards/handwired/wulkan/wulkan.h @@ -0,0 +1,21 @@ +#pragma once + +#include "quantum.h" + +#define ___ KC_NO + +#define LAYOUT_ortho_4x12( \ + K00, K01, K02, K03, K04, K05, K06, K07, K08, K09, K0A, K0B, \ + K10, K11, K12, K13, K14, K15, K16, K17, K18, K19, K1A, K1B, \ + K20, K21, K22, K23, K24, K25, K26, K27, K28, K29, K2A, K2B, \ + K30, K31, K32, K33, K34, K35, K36, K37, K38, K39, K3A, K3B \ +) \ +{ \ + { K00, K01, K02, K03, K04, K05, K06, K07, K08, K09, K0A, K0B }, \ + { K10, K11, K12, K13, K14, K15, K16, K17, K18, K19, K1A, K1B }, \ + { K20, K21, K22, K23, K24, K25, K26, K27, K28, K29, K2A, K2B }, \ + { K30, K31, K32, K33, K34, K35, K36, K37, K38, K39, K3A, K3B } \ +} + + +#define LAYOUT LAYOUT_ortho_4x12 diff --git a/keyboards/handwired/xealous/rev1/config.h b/keyboards/handwired/xealous/rev1/config.h index f58c8f90b..ab39dfbc1 100644 --- a/keyboards/handwired/xealous/rev1/config.h +++ b/keyboards/handwired/xealous/rev1/config.h @@ -62,7 +62,7 @@ along with this program. If not, see <http://www.gnu.org/licenses/>. // #define BACKLIGHT_LEVELS 3 /* Set 0 if debouncing isn't needed */ -#define DEBOUNCING_DELAY 5 +#define DEBOUNCE 5 /* * Feature disable options |