diff options
Diffstat (limited to 'keyboards/wilba_tech/wt8_a')
| -rw-r--r-- | keyboards/wilba_tech/wt8_a/config.h | 12 | ||||
| -rw-r--r-- | keyboards/wilba_tech/wt8_a/rules.mk | 53 |
2 files changed, 17 insertions, 48 deletions
diff --git a/keyboards/wilba_tech/wt8_a/config.h b/keyboards/wilba_tech/wt8_a/config.h index 6604b7ce8..08556650d 100644 --- a/keyboards/wilba_tech/wt8_a/config.h +++ b/keyboards/wilba_tech/wt8_a/config.h @@ -100,16 +100,16 @@ // TODO: refactor with new user EEPROM code (coming soon) #define EEPROM_MAGIC 0x451F -#define EEPROM_MAGIC_ADDR 32 +#define EEPROM_MAGIC_ADDR 34 // Bump this every time we change what we store // This will automatically reset the EEPROM with defaults // and avoid loading invalid data from the EEPROM #define EEPROM_VERSION 0x08 -#define EEPROM_VERSION_ADDR 34 +#define EEPROM_VERSION_ADDR 36 // Dynamic keymap starts after EEPROM version -#define DYNAMIC_KEYMAP_EEPROM_ADDR 35 -// Dynamic macro starts after dynamic keymaps (35+(4*1*8*2)) = (35+64) -#define DYNAMIC_KEYMAP_MACRO_EEPROM_ADDR 99 -#define DYNAMIC_KEYMAP_MACRO_EEPROM_SIZE 925 +#define DYNAMIC_KEYMAP_EEPROM_ADDR 37 +// Dynamic macro starts after dynamic keymaps (37+(4*1*8*2)) = (37+64) +#define DYNAMIC_KEYMAP_MACRO_EEPROM_ADDR 101 +#define DYNAMIC_KEYMAP_MACRO_EEPROM_SIZE 923 #define DYNAMIC_KEYMAP_MACRO_COUNT 16 diff --git a/keyboards/wilba_tech/wt8_a/rules.mk b/keyboards/wilba_tech/wt8_a/rules.mk index f1c632289..7d1c2aa1b 100644 --- a/keyboards/wilba_tech/wt8_a/rules.mk +++ b/keyboards/wilba_tech/wt8_a/rules.mk @@ -1,50 +1,16 @@ -# project specific files -SRC = keyboards/wilba_tech/wt_main.c - # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = atmel-dfu - # Build Options # change yes to no to disable # @@ -63,3 +29,6 @@ UNICODE_ENABLE = no # Unicode BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID AUDIO_ENABLE = no # Audio output on port C6 FAUXCLICKY_ENABLE = no # Use buzzer to emulate clicky switches + +# project specific files +SRC = keyboards/wilba_tech/wt_main.c |