From 44441de8cad7255fd0637459ed39b89e34751b78 Mon Sep 17 00:00:00 2001 From: Fred Sundvik Date: Sun, 7 Aug 2016 17:04:39 +0300 Subject: Split keyboard makefiles into rules and Makefile --- keyboards/clueboard/rules.mk | 103 +++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 103 insertions(+) create mode 100644 keyboards/clueboard/rules.mk (limited to 'keyboards/clueboard/rules.mk') diff --git a/keyboards/clueboard/rules.mk b/keyboards/clueboard/rules.mk new file mode 100644 index 000000000..3909fbd5c --- /dev/null +++ b/keyboards/clueboard/rules.mk @@ -0,0 +1,103 @@ +#---------------------------------------------------------------------------- +# On command line: +# +# make all = Make software. +# +# make clean = Clean out built project files. +# +# make coff = Convert ELF to AVR COFF. +# +# make extcoff = Convert ELF to AVR Extended COFF. +# +# make program = Download the hex file to the device. +# Please customize your programmer settings(PROGRAM_CMD) +# +# make teensy = Download the hex file to the device, using teensy_loader_cli. +# (must have teensy_loader_cli installed). +# +# make dfu = Download the hex file to the device, using dfu-programmer (must +# have dfu-programmer installed). +# +# make flip = Download the hex file to the device, using Atmel FLIP (must +# have Atmel FLIP installed). +# +# make dfu-ee = Download the eeprom file to the device, using dfu-programmer +# (must have dfu-programmer installed). +# +# make flip-ee = Download the eeprom file to the device, using Atmel FLIP +# (must have Atmel FLIP installed). +# +# make debug = Start either simulavr or avarice as specified for debugging, +# with avr-gdb or avr-insight as the front end for debugging. +# +# make filename.s = Just compile filename.c into the assembler code only. +# +# make filename.i = Create a preprocessed source file for use in submitting +# bug reports to the GCC project. +# +# To rebuild project do "make clean" then "make all". +#---------------------------------------------------------------------------- + +# MCU name +MCU = atmega32u4 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + +# Boot Section Size in *bytes* +# Teensy halfKay 512 +# Teensy++ halfKay 1024 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +# USBaspLoader 2048 +OPT_DEFS += -DBOOTLOADER_SIZE=4096 + + +# Build Options +# comment out to disable the options. +# +BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE ?= no # Mouse keys(+4700) +EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) +CONSOLE_ENABLE ?= yes # Console for debug(+400) +COMMAND_ENABLE ?= yes # Commands for debug and configuration +NKRO_ENABLE ?= yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +AUDIO_ENABLE ?= no +RGBLIGHT_ENABLE ?= no # Enable keyboard underlight functionality +MIDI_ENABLE ?= no # MIDI controls +UNICODE_ENABLE ?= no # Unicode +BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID \ No newline at end of file -- cgit v1.2.3-70-g09d2