From 3dbf08b655ac1f14bc7a5ae2b8cd8ae385063640 Mon Sep 17 00:00:00 2001 From: fauxpark Date: Mon, 21 Oct 2019 06:51:37 +1100 Subject: Cleanup rules.mk for 32U4 keyboards, H (#7030) * Cleanup rules.mk for 32U4 keyboards, H * Change some boards incorrectly assumed to be halfkay --- keyboards/handwired/frenchdev/rules.mk | 77 ++++++---------------------------- 1 file changed, 13 insertions(+), 64 deletions(-) (limited to 'keyboards/handwired/frenchdev') diff --git a/keyboards/handwired/frenchdev/rules.mk b/keyboards/handwired/frenchdev/rules.mk index 69a12b68d..abf4e62c4 100644 --- a/keyboards/handwired/frenchdev/rules.mk +++ b/keyboards/handwired/frenchdev/rules.mk @@ -1,70 +1,15 @@ -#---------------------------------------------------------------------------- -# On command line: -# -# make = Make software. -# -# make clean = Clean out built project files. -# -# That's pretty much all you need. To compile, always go make clean, -# followed by make. -# -# For advanced users only: -# make teensy = Download the hex file to the device, using teensy_loader_cli. -# (must have teensy_loader_cli installed). -# -#---------------------------------------------------------------------------- - -# # project specific files -SRC = i2c_master.c \ - matrix.c - # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -BOOTLOADER = halfKay +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp +BOOTLOADER = halfkay # Build Options # comment out to disable the options. @@ -85,3 +30,7 @@ BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID AUDIO_ENABLE = no # Audio output on port C6 RGBLIGHT_ENABLE = no API_SYSEX_ENABLE = no + +# project specific files +SRC = i2c_master.c \ + matrix.c -- cgit v1.2.3-70-g09d2