From 44441de8cad7255fd0637459ed39b89e34751b78 Mon Sep 17 00:00:00 2001 From: Fred Sundvik Date: Sun, 7 Aug 2016 17:04:39 +0300 Subject: Split keyboard makefiles into rules and Makefile --- keyboards/handwired/Makefile | 2 +- keyboards/handwired/onekey/Makefile | 66 ++----------------------------------- keyboards/handwired/rules.mk | 0 3 files changed, 3 insertions(+), 65 deletions(-) create mode 100644 keyboards/handwired/rules.mk (limited to 'keyboards/handwired') diff --git a/keyboards/handwired/Makefile b/keyboards/handwired/Makefile index 57493a47c..4e2a6f00f 100644 --- a/keyboards/handwired/Makefile +++ b/keyboards/handwired/Makefile @@ -1,3 +1,3 @@ -ifndef QUANTUM_DIR +ifndef MAKEFILE_INCLUDED include ../../Makefile endif \ No newline at end of file diff --git a/keyboards/handwired/onekey/Makefile b/keyboards/handwired/onekey/Makefile index c6d10856a..4e2a6f00f 100644 --- a/keyboards/handwired/onekey/Makefile +++ b/keyboards/handwired/onekey/Makefile @@ -1,65 +1,3 @@ - - -# MCU name -MCU = atmega32u4 - -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=4096 - - -# Build Options -# comment out to disable the options. -# -BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000) -MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) -EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) -CONSOLE_ENABLE ?= yes # Console for debug(+400) -COMMAND_ENABLE ?= yes # Commands for debug and configuration -#SLEEP_LED_ENABLE = yes # Breathing sleep LED during USB suspend -#NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA - -ifndef QUANTUM_DIR - include ../../../Makefile +ifndef MAKEFILE_INCLUDED + include ../../Makefile endif \ No newline at end of file diff --git a/keyboards/handwired/rules.mk b/keyboards/handwired/rules.mk new file mode 100644 index 000000000..e69de29bb -- cgit v1.3.1 From 051017c3129a17a1f4c610f19067c60bf0a49da9 Mon Sep 17 00:00:00 2001 From: Fred Sundvik Date: Sun, 7 Aug 2016 18:38:03 +0300 Subject: Split subproject make files into Makefile and rules.mk --- keyboards/chibios_test/stm32_f072_onekey/Makefile | 42 +---------- keyboards/chibios_test/stm32_f072_onekey/rules.mk | 41 +++++++++++ keyboards/chibios_test/stm32_f103_onekey/Makefile | 53 +------------ keyboards/chibios_test/stm32_f103_onekey/rules.mk | 52 +++++++++++++ keyboards/chibios_test/teensy_lc_onekey/Makefile | 48 +----------- keyboards/chibios_test/teensy_lc_onekey/rules.mk | 49 ++++++++++++ keyboards/clueboard/rev1/Makefile | 6 +- keyboards/clueboard/rev1/rules.mk | 5 ++ keyboards/clueboard/rev2/Makefile | 6 +- keyboards/clueboard/rev2/rules.mk | 5 ++ keyboards/ergodox/ez/Makefile | 77 +------------------ keyboards/ergodox/ez/rules.mk | 76 +++++++++++++++++++ keyboards/ergodox/infinity/Makefile | 78 +------------------- keyboards/ergodox/infinity/rules.mk | 77 +++++++++++++++++++ keyboards/handwired/CMD60/Makefile | 74 +------------------ keyboards/handwired/CMD60/rules.mk | 73 ++++++++++++++++++ keyboards/handwired/fivethirteen/Makefile | 74 +------------------ keyboards/handwired/fivethirteen/rules.mk | 73 ++++++++++++++++++ keyboards/handwired/minorca/Makefile | 70 +----------------- keyboards/handwired/minorca/rules.mk | 67 +++++++++++++++++ keyboards/handwired/onekey/Makefile | 2 +- keyboards/handwired/onekey/rules.mk | 65 ++++++++++++++++ keyboards/handwired/traveller/Makefile | 90 +---------------------- keyboards/handwired/traveller/rules.mk | 89 ++++++++++++++++++++++ keyboards/planck/rev3/Makefile | 4 +- keyboards/planck/rev3/rules.mk | 5 ++ keyboards/planck/rev4/Makefile | 4 +- keyboards/planck/rev4/rules.mk | 5 ++ 28 files changed, 705 insertions(+), 605 deletions(-) create mode 100644 keyboards/chibios_test/stm32_f072_onekey/rules.mk create mode 100644 keyboards/chibios_test/stm32_f103_onekey/rules.mk create mode 100644 keyboards/chibios_test/teensy_lc_onekey/rules.mk create mode 100644 keyboards/clueboard/rev1/rules.mk create mode 100644 keyboards/clueboard/rev2/rules.mk create mode 100644 keyboards/ergodox/ez/rules.mk create mode 100644 keyboards/ergodox/infinity/rules.mk create mode 100644 keyboards/handwired/CMD60/rules.mk create mode 100644 keyboards/handwired/fivethirteen/rules.mk create mode 100644 keyboards/handwired/minorca/rules.mk create mode 100644 keyboards/handwired/onekey/rules.mk create mode 100644 keyboards/handwired/traveller/rules.mk create mode 100644 keyboards/planck/rev3/rules.mk create mode 100644 keyboards/planck/rev4/rules.mk (limited to 'keyboards/handwired') diff --git a/keyboards/chibios_test/stm32_f072_onekey/Makefile b/keyboards/chibios_test/stm32_f072_onekey/Makefile index eae38c4b2..191c6bb66 100644 --- a/keyboards/chibios_test/stm32_f072_onekey/Makefile +++ b/keyboards/chibios_test/stm32_f072_onekey/Makefile @@ -1,41 +1,3 @@ -# project specific files -SRC = matrix.c \ - led.c - -## chip/board settings -# the next two should match the directories in -# /os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES) -MCU_FAMILY = STM32 -MCU_SERIES = STM32F0xx -# linker script to use -# it should exist either in /os/common/ports/ARMCMx/compilers/GCC/ld/ -# or /ld/ -MCU_LDSCRIPT = STM32F072xB -# startup code to use -# is should exist in /os/common/ports/ARMCMx/compilers/GCC/mk/ -MCU_STARTUP = stm32f0xx -# it should exist either in /os/hal/boards/ -# or /boards -BOARD = ST_STM32F072B_DISCOVERY -# Cortex version -# Teensy LC is cortex-m0; Teensy 3.x are cortex-m4 -MCU = cortex-m0 -# ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7 -ARMV = 6 -# If you want to be able to jump to bootloader from firmware on STM32 MCUs, -# set the correct BOOTLOADER_ADDRESS. Either set it here, or define it in -# ./bootloader_defs.h or in ./boards//bootloader_defs.h (if you have -# a custom board definition that you plan to reuse). -# If you're not setting it here, leave it commented out. -# It is chip dependent, the correct number can be looked up here (page 175): -# http://www.st.com/web/en/resource/technical/document/application_note/CD00167594.pdf -# This also requires a patch to chibios: -# /tmk_core/tool/chibios/ch-bootloader-jump.patch -#STM32_BOOTLOADER_ADDRESS = 0x1FFFC800 - -# Build Options -# comment out to disable the options. -# -ifndef QUANTUM_DIR +ifndef MAKEFILE_INCLUDED include ../../../Makefile -endif +endif \ No newline at end of file diff --git a/keyboards/chibios_test/stm32_f072_onekey/rules.mk b/keyboards/chibios_test/stm32_f072_onekey/rules.mk new file mode 100644 index 000000000..eae38c4b2 --- /dev/null +++ b/keyboards/chibios_test/stm32_f072_onekey/rules.mk @@ -0,0 +1,41 @@ +# project specific files +SRC = matrix.c \ + led.c + +## chip/board settings +# the next two should match the directories in +# /os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES) +MCU_FAMILY = STM32 +MCU_SERIES = STM32F0xx +# linker script to use +# it should exist either in /os/common/ports/ARMCMx/compilers/GCC/ld/ +# or /ld/ +MCU_LDSCRIPT = STM32F072xB +# startup code to use +# is should exist in /os/common/ports/ARMCMx/compilers/GCC/mk/ +MCU_STARTUP = stm32f0xx +# it should exist either in /os/hal/boards/ +# or /boards +BOARD = ST_STM32F072B_DISCOVERY +# Cortex version +# Teensy LC is cortex-m0; Teensy 3.x are cortex-m4 +MCU = cortex-m0 +# ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7 +ARMV = 6 +# If you want to be able to jump to bootloader from firmware on STM32 MCUs, +# set the correct BOOTLOADER_ADDRESS. Either set it here, or define it in +# ./bootloader_defs.h or in ./boards//bootloader_defs.h (if you have +# a custom board definition that you plan to reuse). +# If you're not setting it here, leave it commented out. +# It is chip dependent, the correct number can be looked up here (page 175): +# http://www.st.com/web/en/resource/technical/document/application_note/CD00167594.pdf +# This also requires a patch to chibios: +# /tmk_core/tool/chibios/ch-bootloader-jump.patch +#STM32_BOOTLOADER_ADDRESS = 0x1FFFC800 + +# Build Options +# comment out to disable the options. +# +ifndef QUANTUM_DIR + include ../../../Makefile +endif diff --git a/keyboards/chibios_test/stm32_f103_onekey/Makefile b/keyboards/chibios_test/stm32_f103_onekey/Makefile index 307ca5b19..191c6bb66 100644 --- a/keyboards/chibios_test/stm32_f103_onekey/Makefile +++ b/keyboards/chibios_test/stm32_f103_onekey/Makefile @@ -1,52 +1,3 @@ -# project specific files -SRC = matrix.c \ - led.c - -# GENERIC STM32F103C8T6 board - stm32duino bootloader -OPT_DEFS = -DCORTEX_VTOR_INIT=0x2000 -MCU_LDSCRIPT = STM32F103x8_stm32duino_bootloader -BOARD = GENERIC_STM32_F103 - -# GENERIC STM32F103C8T6 board - no bootloader (programmer over serial or SWD) -# OPT_DEFS = -# MCU_LDSCRIPT = STM32F103x8 -# BOARD = GENERIC_STM32_F103 - -# MAPLE MINI -# OPT_DEFS = -DCORTEX_VTOR_INIT=0x5000 -# MCU_LDSCRIPT = STM32F103xB_maplemini_bootloader -# BOARD = MAPLEMINI_STM32_F103 - -## chip/board settings -# the next two should match the directories in -# /os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES) -MCU_FAMILY = STM32 -MCU_SERIES = STM32F1xx -# linker script to use -# it should exist either in /os/common/ports/ARMCMx/compilers/GCC/ld/ -# or /ld/ -# startup code to use -# is should exist in /os/common/ports/ARMCMx/compilers/GCC/mk/ -MCU_STARTUP = stm32f1xx -# it should exist either in /os/hal/boards/ -# or /boards -# Cortex version -# Teensy LC is cortex-m0; Teensy 3.x are cortex-m4 -MCU = cortex-m3 -# ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7 -ARMV = 7 -# If you want to be able to jump to bootloader from firmware on STM32 MCUs, -# set the correct BOOTLOADER_ADDRESS. Either set it here, or define it in -# ./bootloader_defs.h or in ./boards//bootloader_defs.h (if you have -# a custom board definition that you plan to reuse). -# If you're not setting it here, leave it commented out. -# It is chip dependent, the correct number can be looked up here (page 175): -# http://www.st.com/web/en/resource/technical/document/application_note/CD00167594.pdf -# This also requires a patch to chibios: -# /tmk_core/tool/chibios/ch-bootloader-jump.patch -#STM32_BOOTLOADER_ADDRESS = 0x1FFFC800 - - -ifndef QUANTUM_DIR +ifndef MAKEFILE_INCLUDED include ../../../Makefile -endif +endif \ No newline at end of file diff --git a/keyboards/chibios_test/stm32_f103_onekey/rules.mk b/keyboards/chibios_test/stm32_f103_onekey/rules.mk new file mode 100644 index 000000000..307ca5b19 --- /dev/null +++ b/keyboards/chibios_test/stm32_f103_onekey/rules.mk @@ -0,0 +1,52 @@ +# project specific files +SRC = matrix.c \ + led.c + +# GENERIC STM32F103C8T6 board - stm32duino bootloader +OPT_DEFS = -DCORTEX_VTOR_INIT=0x2000 +MCU_LDSCRIPT = STM32F103x8_stm32duino_bootloader +BOARD = GENERIC_STM32_F103 + +# GENERIC STM32F103C8T6 board - no bootloader (programmer over serial or SWD) +# OPT_DEFS = +# MCU_LDSCRIPT = STM32F103x8 +# BOARD = GENERIC_STM32_F103 + +# MAPLE MINI +# OPT_DEFS = -DCORTEX_VTOR_INIT=0x5000 +# MCU_LDSCRIPT = STM32F103xB_maplemini_bootloader +# BOARD = MAPLEMINI_STM32_F103 + +## chip/board settings +# the next two should match the directories in +# /os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES) +MCU_FAMILY = STM32 +MCU_SERIES = STM32F1xx +# linker script to use +# it should exist either in /os/common/ports/ARMCMx/compilers/GCC/ld/ +# or /ld/ +# startup code to use +# is should exist in /os/common/ports/ARMCMx/compilers/GCC/mk/ +MCU_STARTUP = stm32f1xx +# it should exist either in /os/hal/boards/ +# or /boards +# Cortex version +# Teensy LC is cortex-m0; Teensy 3.x are cortex-m4 +MCU = cortex-m3 +# ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7 +ARMV = 7 +# If you want to be able to jump to bootloader from firmware on STM32 MCUs, +# set the correct BOOTLOADER_ADDRESS. Either set it here, or define it in +# ./bootloader_defs.h or in ./boards//bootloader_defs.h (if you have +# a custom board definition that you plan to reuse). +# If you're not setting it here, leave it commented out. +# It is chip dependent, the correct number can be looked up here (page 175): +# http://www.st.com/web/en/resource/technical/document/application_note/CD00167594.pdf +# This also requires a patch to chibios: +# /tmk_core/tool/chibios/ch-bootloader-jump.patch +#STM32_BOOTLOADER_ADDRESS = 0x1FFFC800 + + +ifndef QUANTUM_DIR + include ../../../Makefile +endif diff --git a/keyboards/chibios_test/teensy_lc_onekey/Makefile b/keyboards/chibios_test/teensy_lc_onekey/Makefile index 43ea9d82d..191c6bb66 100644 --- a/keyboards/chibios_test/teensy_lc_onekey/Makefile +++ b/keyboards/chibios_test/teensy_lc_onekey/Makefile @@ -1,49 +1,3 @@ -# project specific files -SRC = matrix.c \ - led.c - -## chip/board settings -# - the next two should match the directories in -# /os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES) -# - For Teensies, FAMILY = KINETIS and SERIES is either -# KL2x (LC) or K20x (3.0,3.1,3.2). -MCU_FAMILY = KINETIS -MCU_SERIES = KL2x - -# Linker script to use -# - it should exist either in /os/common/ports/ARMCMx/compilers/GCC/ld/ -# or /ld/ -# - NOTE: a custom ld script is needed for EEPROM on Teensy LC -# - LDSCRIPT = -# - MKL26Z64 for Teensy LC -# - MK20DX128 for Teensy 3.0 -# - MK20DX256 for Teensy 3.1 and 3.2 -MCU_LDSCRIPT = MKL26Z64 - -# Startup code to use -# - it should exist in /os/common/ports/ARMCMx/compilers/GCC/mk/ -# - STARTUP = -# - kl2x for Teensy LC -# - k20x5 for Teensy 3.0 -# - k20x7 for Teensy 3.1 and 3.2 -MCU_STARTUP = kl2x - -# Board: it should exist either in /os/hal/boards/ -# or /boards -# - BOARD = -# - PJRC_TEENSY_LC for Teensy LC -# - PJRC_TEENSY_3 for Teensy 3.0 -# - PJRC_TEENSY_3_1 for Teensy 3.1 or 3.2 -BOARD = PJRC_TEENSY_LC - -# Cortex version -# Teensy LC is cortex-m0plus; Teensy 3.x are cortex-m4 -MCU = cortex-m0plus - -# ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7 -# I.e. 6 for Teensy LC; 7 for Teensy 3.x -ARMV = 6 - -ifndef QUANTUM_DIR +ifndef MAKEFILE_INCLUDED include ../../../Makefile endif \ No newline at end of file diff --git a/keyboards/chibios_test/teensy_lc_onekey/rules.mk b/keyboards/chibios_test/teensy_lc_onekey/rules.mk new file mode 100644 index 000000000..43ea9d82d --- /dev/null +++ b/keyboards/chibios_test/teensy_lc_onekey/rules.mk @@ -0,0 +1,49 @@ +# project specific files +SRC = matrix.c \ + led.c + +## chip/board settings +# - the next two should match the directories in +# /os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES) +# - For Teensies, FAMILY = KINETIS and SERIES is either +# KL2x (LC) or K20x (3.0,3.1,3.2). +MCU_FAMILY = KINETIS +MCU_SERIES = KL2x + +# Linker script to use +# - it should exist either in /os/common/ports/ARMCMx/compilers/GCC/ld/ +# or /ld/ +# - NOTE: a custom ld script is needed for EEPROM on Teensy LC +# - LDSCRIPT = +# - MKL26Z64 for Teensy LC +# - MK20DX128 for Teensy 3.0 +# - MK20DX256 for Teensy 3.1 and 3.2 +MCU_LDSCRIPT = MKL26Z64 + +# Startup code to use +# - it should exist in /os/common/ports/ARMCMx/compilers/GCC/mk/ +# - STARTUP = +# - kl2x for Teensy LC +# - k20x5 for Teensy 3.0 +# - k20x7 for Teensy 3.1 and 3.2 +MCU_STARTUP = kl2x + +# Board: it should exist either in /os/hal/boards/ +# or /boards +# - BOARD = +# - PJRC_TEENSY_LC for Teensy LC +# - PJRC_TEENSY_3 for Teensy 3.0 +# - PJRC_TEENSY_3_1 for Teensy 3.1 or 3.2 +BOARD = PJRC_TEENSY_LC + +# Cortex version +# Teensy LC is cortex-m0plus; Teensy 3.x are cortex-m4 +MCU = cortex-m0plus + +# ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7 +# I.e. 6 for Teensy LC; 7 for Teensy 3.x +ARMV = 6 + +ifndef QUANTUM_DIR + include ../../../Makefile +endif \ No newline at end of file diff --git a/keyboards/clueboard/rev1/Makefile b/keyboards/clueboard/rev1/Makefile index 80a942d06..191c6bb66 100644 --- a/keyboards/clueboard/rev1/Makefile +++ b/keyboards/clueboard/rev1/Makefile @@ -1,5 +1,3 @@ -BACKLIGHT_ENABLE = no - -ifndef QUANTUM_DIR +ifndef MAKEFILE_INCLUDED include ../../../Makefile -endif +endif \ No newline at end of file diff --git a/keyboards/clueboard/rev1/rules.mk b/keyboards/clueboard/rev1/rules.mk new file mode 100644 index 000000000..80a942d06 --- /dev/null +++ b/keyboards/clueboard/rev1/rules.mk @@ -0,0 +1,5 @@ +BACKLIGHT_ENABLE = no + +ifndef QUANTUM_DIR + include ../../../Makefile +endif diff --git a/keyboards/clueboard/rev2/Makefile b/keyboards/clueboard/rev2/Makefile index cea967b79..191c6bb66 100644 --- a/keyboards/clueboard/rev2/Makefile +++ b/keyboards/clueboard/rev2/Makefile @@ -1,5 +1,3 @@ -BACKLIGHT_ENABLE = yes - -ifndef QUANTUM_DIR +ifndef MAKEFILE_INCLUDED include ../../../Makefile -endif +endif \ No newline at end of file diff --git a/keyboards/clueboard/rev2/rules.mk b/keyboards/clueboard/rev2/rules.mk new file mode 100644 index 000000000..cea967b79 --- /dev/null +++ b/keyboards/clueboard/rev2/rules.mk @@ -0,0 +1,5 @@ +BACKLIGHT_ENABLE = yes + +ifndef QUANTUM_DIR + include ../../../Makefile +endif diff --git a/keyboards/ergodox/ez/Makefile b/keyboards/ergodox/ez/Makefile index 37e554b30..191c6bb66 100644 --- a/keyboards/ergodox/ez/Makefile +++ b/keyboards/ergodox/ez/Makefile @@ -1,76 +1,3 @@ -#---------------------------------------------------------------------------- -# On command line: -# -# make = Make software. -# -# make clean = Clean out built project files. -# -# That's pretty much all you need. To compile, always go make clean, -# followed by make. -# -# For advanced users only: -# make teensy = Download the hex file to the device, using teensy_loader_cli. -# (must have teensy_loader_cli installed). -# -#---------------------------------------------------------------------------- - -# # project specific files -SRC = twimaster.c \ - matrix.c - -# MCU name -MCU = atmega32u4 - -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=512 - - -# Build Options -# comment out to disable the options. -# - -ifndef QUANTUM_DIR +ifndef MAKEFILE_INCLUDED include ../../../Makefile -endif +endif \ No newline at end of file diff --git a/keyboards/ergodox/ez/rules.mk b/keyboards/ergodox/ez/rules.mk new file mode 100644 index 000000000..37e554b30 --- /dev/null +++ b/keyboards/ergodox/ez/rules.mk @@ -0,0 +1,76 @@ +#---------------------------------------------------------------------------- +# On command line: +# +# make = Make software. +# +# make clean = Clean out built project files. +# +# That's pretty much all you need. To compile, always go make clean, +# followed by make. +# +# For advanced users only: +# make teensy = Download the hex file to the device, using teensy_loader_cli. +# (must have teensy_loader_cli installed). +# +#---------------------------------------------------------------------------- + +# # project specific files +SRC = twimaster.c \ + matrix.c + +# MCU name +MCU = atmega32u4 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + +# Boot Section Size in *bytes* +# Teensy halfKay 512 +# Teensy++ halfKay 1024 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +# USBaspLoader 2048 +OPT_DEFS += -DBOOTLOADER_SIZE=512 + + +# Build Options +# comment out to disable the options. +# + +ifndef QUANTUM_DIR + include ../../../Makefile +endif diff --git a/keyboards/ergodox/infinity/Makefile b/keyboards/ergodox/infinity/Makefile index ccb735a48..191c6bb66 100644 --- a/keyboards/ergodox/infinity/Makefile +++ b/keyboards/ergodox/infinity/Makefile @@ -1,77 +1,3 @@ -# project specific files -SRC = matrix.c \ - led.c - -## chip/board settings -# - the next two should match the directories in -# /os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES) -# - For Teensies, FAMILY = KINETIS and SERIES is either -# KL2x (LC) or K20x (3.0,3.1,3.2). -# - For Infinity KB, SERIES = K20x -MCU_FAMILY = KINETIS -MCU_SERIES = K20x - -# Linker script to use -# - it should exist either in /os/common/ports/ARMCMx/compilers/GCC/ld/ -# or /ld/ -# - NOTE: a custom ld script is needed for EEPROM on Teensy LC -# - LDSCRIPT = -# - MKL26Z64 for Teensy LC -# - MK20DX128 for Teensy 3.0 -# - MK20DX256 for Teensy 3.1 and 3.2 -# - MK20DX128BLDR4 for Infinity 60% with Kiibohd bootloader -# - MK20DX256BLDR8 for Infinity ErgoDox with Kiibohd bootloader -MCU_LDSCRIPT = MK20DX256BLDR8 - -# Startup code to use -# - it should exist in /os/common/ports/ARMCMx/compilers/GCC/mk/ -# - STARTUP = -# - kl2x for Teensy LC -# - k20x5 for Teensy 3.0 and Infinity 60% -# - k20x7 for Teensy 3.1, 3.2 and Infinity ErgoDox -MCU_STARTUP = k20x7 - -# Board: it should exist either in /os/hal/boards/ -# or /boards -# - BOARD = -# - PJRC_TEENSY_LC for Teensy LC -# - PJRC_TEENSY_3 for Teensy 3.0 -# - PJRC_TEENSY_3_1 for Teensy 3.1 or 3.2 -# - MCHCK_K20 for Infinity KB -#BOARD = MCHCK_K20 -BOARD = PJRC_TEENSY_3_1 - -# Cortex version -# Teensy LC is cortex-m0; Teensy 3.x are cortex-m4 -MCU = cortex-m4 - -# ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7 -# I.e. 6 for Teensy LC; 7 for Teensy 3.x -ARMV = 7 - -# Vector table for application -# 0x00000000-0x00001000 area is occupied by bootlaoder.*/ -# The CORTEX_VTOR... is needed only for MCHCK/Infinity KB -OPT_DEFS += -DCORTEX_VTOR_INIT=0x00002000 - -# Build Options -# comment out to disable the options. -# -CUSTOM_MATRIX ?= yes # Custom matrix file -SERIAL_LINK_ENABLE = yes -VISUALIZER_ENABLE ?= no #temporarily disabled to make everything compile -LCD_ENABLE ?= yes -LED_ENABLE ?= yes -LCD_BACKLIGHT_ENABLE ?= yes - -ifndef QUANTUM_DIR +ifndef MAKEFILE_INCLUDED include ../../../Makefile -endif - -ifdef LCD_ENABLE -include $(SUBPROJECT_PATH)/drivers/gdisp/st7565ergodox/driver.mk -endif - -ifdef LED_ENABLE -include $(SUBPROJECT_PATH)/drivers/gdisp/IS31FL3731C/driver.mk -endif +endif \ No newline at end of file diff --git a/keyboards/ergodox/infinity/rules.mk b/keyboards/ergodox/infinity/rules.mk new file mode 100644 index 000000000..ccb735a48 --- /dev/null +++ b/keyboards/ergodox/infinity/rules.mk @@ -0,0 +1,77 @@ +# project specific files +SRC = matrix.c \ + led.c + +## chip/board settings +# - the next two should match the directories in +# /os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES) +# - For Teensies, FAMILY = KINETIS and SERIES is either +# KL2x (LC) or K20x (3.0,3.1,3.2). +# - For Infinity KB, SERIES = K20x +MCU_FAMILY = KINETIS +MCU_SERIES = K20x + +# Linker script to use +# - it should exist either in /os/common/ports/ARMCMx/compilers/GCC/ld/ +# or /ld/ +# - NOTE: a custom ld script is needed for EEPROM on Teensy LC +# - LDSCRIPT = +# - MKL26Z64 for Teensy LC +# - MK20DX128 for Teensy 3.0 +# - MK20DX256 for Teensy 3.1 and 3.2 +# - MK20DX128BLDR4 for Infinity 60% with Kiibohd bootloader +# - MK20DX256BLDR8 for Infinity ErgoDox with Kiibohd bootloader +MCU_LDSCRIPT = MK20DX256BLDR8 + +# Startup code to use +# - it should exist in /os/common/ports/ARMCMx/compilers/GCC/mk/ +# - STARTUP = +# - kl2x for Teensy LC +# - k20x5 for Teensy 3.0 and Infinity 60% +# - k20x7 for Teensy 3.1, 3.2 and Infinity ErgoDox +MCU_STARTUP = k20x7 + +# Board: it should exist either in /os/hal/boards/ +# or /boards +# - BOARD = +# - PJRC_TEENSY_LC for Teensy LC +# - PJRC_TEENSY_3 for Teensy 3.0 +# - PJRC_TEENSY_3_1 for Teensy 3.1 or 3.2 +# - MCHCK_K20 for Infinity KB +#BOARD = MCHCK_K20 +BOARD = PJRC_TEENSY_3_1 + +# Cortex version +# Teensy LC is cortex-m0; Teensy 3.x are cortex-m4 +MCU = cortex-m4 + +# ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7 +# I.e. 6 for Teensy LC; 7 for Teensy 3.x +ARMV = 7 + +# Vector table for application +# 0x00000000-0x00001000 area is occupied by bootlaoder.*/ +# The CORTEX_VTOR... is needed only for MCHCK/Infinity KB +OPT_DEFS += -DCORTEX_VTOR_INIT=0x00002000 + +# Build Options +# comment out to disable the options. +# +CUSTOM_MATRIX ?= yes # Custom matrix file +SERIAL_LINK_ENABLE = yes +VISUALIZER_ENABLE ?= no #temporarily disabled to make everything compile +LCD_ENABLE ?= yes +LED_ENABLE ?= yes +LCD_BACKLIGHT_ENABLE ?= yes + +ifndef QUANTUM_DIR + include ../../../Makefile +endif + +ifdef LCD_ENABLE +include $(SUBPROJECT_PATH)/drivers/gdisp/st7565ergodox/driver.mk +endif + +ifdef LED_ENABLE +include $(SUBPROJECT_PATH)/drivers/gdisp/IS31FL3731C/driver.mk +endif diff --git a/keyboards/handwired/CMD60/Makefile b/keyboards/handwired/CMD60/Makefile index 711759917..191c6bb66 100644 --- a/keyboards/handwired/CMD60/Makefile +++ b/keyboards/handwired/CMD60/Makefile @@ -1,73 +1,3 @@ - -# MCU name -MCU = atmega32u4 - -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=512 - - -# Build Options -# change yes to no to disable -# -BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000) -MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) -EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) -CONSOLE_ENABLE ?= yes # Console for debug(+400) -COMMAND_ENABLE ?= yes # Commands for debug and configuration -# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE -SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend -# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work -NKRO_ENABLE ?= no # USB Nkey Rollover -BACKLIGHT_ENABLE ?= no # Enable keyboard backlight functionality on B7 by default -MIDI_ENABLE ?= no # MIDI controls -UNICODE_ENABLE ?= no # Unicode -BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID -AUDIO_ENABLE ?= no # Audio output on port C6 - -ifndef QUANTUM_DIR +ifndef MAKEFILE_INCLUDED include ../../../Makefile -endif - - +endif \ No newline at end of file diff --git a/keyboards/handwired/CMD60/rules.mk b/keyboards/handwired/CMD60/rules.mk new file mode 100644 index 000000000..711759917 --- /dev/null +++ b/keyboards/handwired/CMD60/rules.mk @@ -0,0 +1,73 @@ + +# MCU name +MCU = atmega32u4 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + +# Boot Section Size in *bytes* +# Teensy halfKay 512 +# Teensy++ halfKay 1024 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +# USBaspLoader 2048 +OPT_DEFS += -DBOOTLOADER_SIZE=512 + + +# Build Options +# change yes to no to disable +# +BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) +EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) +CONSOLE_ENABLE ?= yes # Console for debug(+400) +COMMAND_ENABLE ?= yes # Commands for debug and configuration +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend +# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +NKRO_ENABLE ?= no # USB Nkey Rollover +BACKLIGHT_ENABLE ?= no # Enable keyboard backlight functionality on B7 by default +MIDI_ENABLE ?= no # MIDI controls +UNICODE_ENABLE ?= no # Unicode +BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID +AUDIO_ENABLE ?= no # Audio output on port C6 + +ifndef QUANTUM_DIR + include ../../../Makefile +endif + + diff --git a/keyboards/handwired/fivethirteen/Makefile b/keyboards/handwired/fivethirteen/Makefile index 711759917..191c6bb66 100644 --- a/keyboards/handwired/fivethirteen/Makefile +++ b/keyboards/handwired/fivethirteen/Makefile @@ -1,73 +1,3 @@ - -# MCU name -MCU = atmega32u4 - -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=512 - - -# Build Options -# change yes to no to disable -# -BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000) -MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) -EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) -CONSOLE_ENABLE ?= yes # Console for debug(+400) -COMMAND_ENABLE ?= yes # Commands for debug and configuration -# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE -SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend -# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work -NKRO_ENABLE ?= no # USB Nkey Rollover -BACKLIGHT_ENABLE ?= no # Enable keyboard backlight functionality on B7 by default -MIDI_ENABLE ?= no # MIDI controls -UNICODE_ENABLE ?= no # Unicode -BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID -AUDIO_ENABLE ?= no # Audio output on port C6 - -ifndef QUANTUM_DIR +ifndef MAKEFILE_INCLUDED include ../../../Makefile -endif - - +endif \ No newline at end of file diff --git a/keyboards/handwired/fivethirteen/rules.mk b/keyboards/handwired/fivethirteen/rules.mk new file mode 100644 index 000000000..711759917 --- /dev/null +++ b/keyboards/handwired/fivethirteen/rules.mk @@ -0,0 +1,73 @@ + +# MCU name +MCU = atmega32u4 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + +# Boot Section Size in *bytes* +# Teensy halfKay 512 +# Teensy++ halfKay 1024 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +# USBaspLoader 2048 +OPT_DEFS += -DBOOTLOADER_SIZE=512 + + +# Build Options +# change yes to no to disable +# +BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) +EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) +CONSOLE_ENABLE ?= yes # Console for debug(+400) +COMMAND_ENABLE ?= yes # Commands for debug and configuration +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend +# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +NKRO_ENABLE ?= no # USB Nkey Rollover +BACKLIGHT_ENABLE ?= no # Enable keyboard backlight functionality on B7 by default +MIDI_ENABLE ?= no # MIDI controls +UNICODE_ENABLE ?= no # Unicode +BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID +AUDIO_ENABLE ?= no # Audio output on port C6 + +ifndef QUANTUM_DIR + include ../../../Makefile +endif + + diff --git a/keyboards/handwired/minorca/Makefile b/keyboards/handwired/minorca/Makefile index 155c1f9a2..191c6bb66 100644 --- a/keyboards/handwired/minorca/Makefile +++ b/keyboards/handwired/minorca/Makefile @@ -1,71 +1,3 @@ -# MCU name -#MCU = at90usb1287 -MCU = atmega32u4 - -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=512 - -# Build Options -# change to "no" to disable the options, or define them in the Makefile in -# the appropriate keymap folder that will get included automatically -# -BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000) -MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) -EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) -CONSOLE_ENABLE ?= no # Console for debug(+400) -COMMAND_ENABLE ?= yes # Commands for debug and configuration -NKRO_ENABLE ?= yes # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work -BACKLIGHT_ENABLE ?= no # Enable keyboard backlight functionality -MIDI_ENABLE ?= no # MIDI controls -AUDIO_ENABLE ?= no # Audio output on port C6 -UNICODE_ENABLE ?= no # Unicode -BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID -RGBLIGHT_ENABLE ?= yes # Enable WS2812 RGB underlight. Do not enable this with audio at the same time. - -# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE -SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend - -ifndef QUANTUM_DIR +ifndef MAKEFILE_INCLUDED include ../../../Makefile endif \ No newline at end of file diff --git a/keyboards/handwired/minorca/rules.mk b/keyboards/handwired/minorca/rules.mk new file mode 100644 index 000000000..c51371a78 --- /dev/null +++ b/keyboards/handwired/minorca/rules.mk @@ -0,0 +1,67 @@ +# MCU name +#MCU = at90usb1287 +MCU = atmega32u4 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + +# Boot Section Size in *bytes* +# Teensy halfKay 512 +# Teensy++ halfKay 1024 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +# USBaspLoader 2048 +OPT_DEFS += -DBOOTLOADER_SIZE=512 + +# Build Options +# change to "no" to disable the options, or define them in the Makefile in +# the appropriate keymap folder that will get included automatically +# +BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) +EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) +CONSOLE_ENABLE ?= no # Console for debug(+400) +COMMAND_ENABLE ?= yes # Commands for debug and configuration +NKRO_ENABLE ?= yes # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +BACKLIGHT_ENABLE ?= no # Enable keyboard backlight functionality +MIDI_ENABLE ?= no # MIDI controls +AUDIO_ENABLE ?= no # Audio output on port C6 +UNICODE_ENABLE ?= no # Unicode +BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID +RGBLIGHT_ENABLE ?= yes # Enable WS2812 RGB underlight. Do not enable this with audio at the same time. + +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend \ No newline at end of file diff --git a/keyboards/handwired/onekey/Makefile b/keyboards/handwired/onekey/Makefile index 4e2a6f00f..191c6bb66 100644 --- a/keyboards/handwired/onekey/Makefile +++ b/keyboards/handwired/onekey/Makefile @@ -1,3 +1,3 @@ ifndef MAKEFILE_INCLUDED - include ../../Makefile + include ../../../Makefile endif \ No newline at end of file diff --git a/keyboards/handwired/onekey/rules.mk b/keyboards/handwired/onekey/rules.mk new file mode 100644 index 000000000..c6d10856a --- /dev/null +++ b/keyboards/handwired/onekey/rules.mk @@ -0,0 +1,65 @@ + + +# MCU name +MCU = atmega32u4 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + +# Boot Section Size in *bytes* +# Teensy halfKay 512 +# Teensy++ halfKay 1024 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +# USBaspLoader 2048 +OPT_DEFS += -DBOOTLOADER_SIZE=4096 + + +# Build Options +# comment out to disable the options. +# +BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) +EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) +CONSOLE_ENABLE ?= yes # Console for debug(+400) +COMMAND_ENABLE ?= yes # Commands for debug and configuration +#SLEEP_LED_ENABLE = yes # Breathing sleep LED during USB suspend +#NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA + +ifndef QUANTUM_DIR + include ../../../Makefile +endif \ No newline at end of file diff --git a/keyboards/handwired/traveller/Makefile b/keyboards/handwired/traveller/Makefile index 12a4b71f4..191c6bb66 100644 --- a/keyboards/handwired/traveller/Makefile +++ b/keyboards/handwired/traveller/Makefile @@ -1,89 +1,3 @@ - -#MCU = at90usb1287 -MCU = atmega32u4 - -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - -# for avr upload -USB ?= /dev/cu.usbmodem1421 -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - - -ifdef TEENSY2 - OPT_DEFS += -DATREUS_TEENSY2 - ATREUS_UPLOAD_COMMAND = teensy_loader_cli -w -mmcu=$(MCU) $(TARGET).hex -else - OPT_DEFS += -DATREUS_ASTAR - OPT_DEFS += -DCATERINA_BOOTLOADER - ATREUS_UPLOAD_COMMAND = while [ ! -r $(USB) ]; do sleep 1; done; \ - avrdude -p $(MCU) -c avr109 -U flash:w:$(TARGET).hex -P $(USB) -endif -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# MCU name - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=4096 - - -# Build Options -# change yes to no to disable -# -BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000) -MOUSEKEY_ENABLE = yes # Mouse keys(+4700) -EXTRAKEY_ENABLE = yes # Audio control and System control(+450) -CONSOLE_ENABLE ?= no # Console for debug(+400) -COMMAND_ENABLE ?= no # Commands for debug and configuration -# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE -SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend -# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work -NKRO_ENABLE ?= no # USB Nkey Rollover -BACKLIGHT_ENABLE ?= no # Enable keyboard backlight functionality on B7 by default -MIDI_ENABLE ?= no # MIDI controls -UNICODE_ENABLE ?= no # Unicode -BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID -AUDIO_ENABLE ?= no # Audio output on port C6 -RGBLIGHT_ENABLE = yes - -ifndef QUANTUM_DIR +ifndef MAKEFILE_INCLUDED include ../../../Makefile -endif - -upload: build - $(ATREUS_UPLOAD_COMMAND) - +endif \ No newline at end of file diff --git a/keyboards/handwired/traveller/rules.mk b/keyboards/handwired/traveller/rules.mk new file mode 100644 index 000000000..12a4b71f4 --- /dev/null +++ b/keyboards/handwired/traveller/rules.mk @@ -0,0 +1,89 @@ + +#MCU = at90usb1287 +MCU = atmega32u4 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + +# for avr upload +USB ?= /dev/cu.usbmodem1421 +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + + +ifdef TEENSY2 + OPT_DEFS += -DATREUS_TEENSY2 + ATREUS_UPLOAD_COMMAND = teensy_loader_cli -w -mmcu=$(MCU) $(TARGET).hex +else + OPT_DEFS += -DATREUS_ASTAR + OPT_DEFS += -DCATERINA_BOOTLOADER + ATREUS_UPLOAD_COMMAND = while [ ! -r $(USB) ]; do sleep 1; done; \ + avrdude -p $(MCU) -c avr109 -U flash:w:$(TARGET).hex -P $(USB) +endif +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + +# MCU name + +# Boot Section Size in *bytes* +# Teensy halfKay 512 +# Teensy++ halfKay 1024 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +# USBaspLoader 2048 +OPT_DEFS += -DBOOTLOADER_SIZE=4096 + + +# Build Options +# change yes to no to disable +# +BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE = yes # Mouse keys(+4700) +EXTRAKEY_ENABLE = yes # Audio control and System control(+450) +CONSOLE_ENABLE ?= no # Console for debug(+400) +COMMAND_ENABLE ?= no # Commands for debug and configuration +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend +# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +NKRO_ENABLE ?= no # USB Nkey Rollover +BACKLIGHT_ENABLE ?= no # Enable keyboard backlight functionality on B7 by default +MIDI_ENABLE ?= no # MIDI controls +UNICODE_ENABLE ?= no # Unicode +BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID +AUDIO_ENABLE ?= no # Audio output on port C6 +RGBLIGHT_ENABLE = yes + +ifndef QUANTUM_DIR + include ../../../Makefile +endif + +upload: build + $(ATREUS_UPLOAD_COMMAND) + diff --git a/keyboards/planck/rev3/Makefile b/keyboards/planck/rev3/Makefile index 3ed1445e4..191c6bb66 100644 --- a/keyboards/planck/rev3/Makefile +++ b/keyboards/planck/rev3/Makefile @@ -1,5 +1,3 @@ -AUDIO_ENABLE ?= no # Audio output on port C6 - -ifndef QUANTUM_DIR +ifndef MAKEFILE_INCLUDED include ../../../Makefile endif \ No newline at end of file diff --git a/keyboards/planck/rev3/rules.mk b/keyboards/planck/rev3/rules.mk new file mode 100644 index 000000000..3ed1445e4 --- /dev/null +++ b/keyboards/planck/rev3/rules.mk @@ -0,0 +1,5 @@ +AUDIO_ENABLE ?= no # Audio output on port C6 + +ifndef QUANTUM_DIR + include ../../../Makefile +endif \ No newline at end of file diff --git a/keyboards/planck/rev4/Makefile b/keyboards/planck/rev4/Makefile index ed09f85a4..191c6bb66 100644 --- a/keyboards/planck/rev4/Makefile +++ b/keyboards/planck/rev4/Makefile @@ -1,5 +1,3 @@ -AUDIO_ENABLE ?= yes # Audio output on port C6 - -ifndef QUANTUM_DIR +ifndef MAKEFILE_INCLUDED include ../../../Makefile endif \ No newline at end of file diff --git a/keyboards/planck/rev4/rules.mk b/keyboards/planck/rev4/rules.mk new file mode 100644 index 000000000..ed09f85a4 --- /dev/null +++ b/keyboards/planck/rev4/rules.mk @@ -0,0 +1,5 @@ +AUDIO_ENABLE ?= yes # Audio output on port C6 + +ifndef QUANTUM_DIR + include ../../../Makefile +endif \ No newline at end of file -- cgit v1.3.1 From 9c574b493c3d098d2c4f2475dfc1564a182acce0 Mon Sep 17 00:00:00 2001 From: IBNobody Date: Tue, 13 Sep 2016 22:05:10 -0500 Subject: Changed Docs, Moved RetroRefit to Handwired --- keyboards/arrow_pad/readme.md | 113 ++++++++++++++++++- keyboards/handwired/retro_refit/Makefile | 3 + keyboards/handwired/retro_refit/config.h | 123 +++++++++++++++++++++ .../handwired/retro_refit/keymaps/default/keymap.c | 33 ++++++ keyboards/handwired/retro_refit/readme.md | 60 ++++++++++ keyboards/handwired/retro_refit/retro_refit.c | 47 ++++++++ keyboards/handwired/retro_refit/retro_refit.h | 38 +++++++ keyboards/handwired/retro_refit/rules.mk | 68 ++++++++++++ keyboards/retro_refit/Makefile | 3 - keyboards/retro_refit/config.h | 123 --------------------- keyboards/retro_refit/keymaps/default/keymap.c | 33 ------ keyboards/retro_refit/readme.md | 26 ----- keyboards/retro_refit/retro_refit.c | 47 -------- keyboards/retro_refit/retro_refit.h | 38 ------- keyboards/retro_refit/rules.mk | 68 ------------ keyboards/vision_division/readme.md | 6 + 16 files changed, 488 insertions(+), 341 deletions(-) create mode 100644 keyboards/handwired/retro_refit/Makefile create mode 100644 keyboards/handwired/retro_refit/config.h create mode 100644 keyboards/handwired/retro_refit/keymaps/default/keymap.c create mode 100644 keyboards/handwired/retro_refit/readme.md create mode 100644 keyboards/handwired/retro_refit/retro_refit.c create mode 100644 keyboards/handwired/retro_refit/retro_refit.h create mode 100644 keyboards/handwired/retro_refit/rules.mk delete mode 100644 keyboards/retro_refit/Makefile delete mode 100644 keyboards/retro_refit/config.h delete mode 100644 keyboards/retro_refit/keymaps/default/keymap.c delete mode 100644 keyboards/retro_refit/readme.md delete mode 100644 keyboards/retro_refit/retro_refit.c delete mode 100644 keyboards/retro_refit/retro_refit.h delete mode 100644 keyboards/retro_refit/rules.mk (limited to 'keyboards/handwired') diff --git a/keyboards/arrow_pad/readme.md b/keyboards/arrow_pad/readme.md index 2e9a64f2e..d0d172272 100644 --- a/keyboards/arrow_pad/readme.md +++ b/keyboards/arrow_pad/readme.md @@ -1,13 +1,120 @@ arrow_pad keyboard firmware ====================== +## Keyboard Info + +The ArrowPad is a wired conversion that can be made to any stand-alone keypad. It uses two main layers - a standard numpad, and a more advanced arrow cluster navigator. + +The first 24-key ArrowPad was handwired, but the PCB was wired as listed below. + +``` + pin + (Silkscreen Name if different) - + + +Note: +U2 pin 2 is the Num Lock LED and is active low. + +U2 pin 1 +Clear (Num Lock) - 1 +Enter - 2 +Esc (ESC) - 2 + + +U2 pin 3 +- - 1 + +U2 pin 4 +7 - 2 +8 - 2 +9 - 2 + +U2 pin 5 +* - 2 +Delete (BACK SPACE) - 2 + +U2 pin 6 +1 - 2 +0 - 2 +. - 2 +, - 2 + +U2 pin 7 +4 - 2 +5 - 2 +6 - 2 + +U2 pin 8 +Tab - 2 += (/) - 2 + +U2 pin 13 +Delete (BACK SPACE) - 1 +9 - 1 +6 - 1 +3 - 1 +. - 1 + +U2 pin 14 +Tab - 1 +8 - 1 +5 - 1 +2 - 1 +0 - 1 + +U2 pin 15 +Esc (ESC) - 1 += (/) - 1 +/ (*) - 1 +7 - 1 +4 - 1 +1 - 1 ++ - 1 + +U2 pin 16 +Enter - 1 +* (<--) - 1 +, - 1 + +U2 pin 17 +Fn (#NAME?) - 1 +- - 2 +Clear (Num Lock) - 2 + +U2 pin 18 +Fn (#NAME?) - 2 +* (<--) - 2 ++ - 2 +3 - 2 +2 - 2 +``` + +More info can be found on [GeekHack](https://geekhack.org/index.php?topic=73632.msg1802497#msg1802497) + +The second ArrowPad was a conversion from a 21-key Genovation keypad. It used a 2 row x 11 column matrix. + +``` +#define KEYMAP( \ + KM_ESC, KM_TAB, KM_BSL, KM_ARR, \ + KM_NUM, KM_FSL, KM_AST, KM_MIN, \ + KM___7, KM___8, KM___9, ___PLS, \ + KM___4, KM___5, KM___6, KM_PLS, \ + KM___1, KM___2, KM___3, ___ENT, \ + KM___0, _____0, KM_DOT, KM_ENT \ +) { \ + { KM_ESC, KM_TAB, KM_BSL, KM_ARR, KM___7, KM___8, KM___9, KM_PLS, KM___1, KM___2, KM___3, }, \ + { KM_NUM, KM_FSL, KM_AST, KM_MIN, KM___4, KM___5, KM___6, KM_ENT, KC_NO, KM___0, KM_DOT, }, \ +} +``` + + ## Quantum MK Firmware For the full Quantum feature list, see [the parent readme.md](/readme.md). ## Building -Download or clone the whole firmware and navigate to the keyboards/arrow_pad folder. Once your dev env is setup, you'll be able to type `make` to generate your .hex - you can then use the Teensy Loader to program your .hex file. +Download or clone the whole firmware and navigate to the keyboards/arrow_pad folder. Once your dev env is setup, you'll be able to type `make` to generate your .hex - you can then use the Teensy Loader to program your .hex file. Depending on which keymap you would like to use, you will have to compile slightly differently. @@ -20,7 +127,7 @@ Several version of keymap are available in advance but you are recommended to de To build the firmware binary hex file with a keymap just do `make` with a keymap like this: ``` -$ make [default|jack|] +$ make [default|pad_21|pad_24|] ``` -Keymaps follow the format **__\.c__** and are stored in the `keymaps` folder. \ No newline at end of file +Keymaps follow the format **__\.c__** and are stored in the `keymaps` folder. diff --git a/keyboards/handwired/retro_refit/Makefile b/keyboards/handwired/retro_refit/Makefile new file mode 100644 index 000000000..191c6bb66 --- /dev/null +++ b/keyboards/handwired/retro_refit/Makefile @@ -0,0 +1,3 @@ +ifndef MAKEFILE_INCLUDED + include ../../../Makefile +endif \ No newline at end of file diff --git a/keyboards/handwired/retro_refit/config.h b/keyboards/handwired/retro_refit/config.h new file mode 100644 index 000000000..f2194e550 --- /dev/null +++ b/keyboards/handwired/retro_refit/config.h @@ -0,0 +1,123 @@ +/* +Copyright 2012 Jun Wako + +This program is free software: you can redistribute it and/or modify +it under the terms of the GNU General Public License as published by +the Free Software Foundation, either version 2 of the License, or +(at your option) any later version. + +This program is distributed in the hope that it will be useful, +but WITHOUT ANY WARRANTY; without even the implied warranty of +MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +GNU General Public License for more details. + +You should have received a copy of the GNU General Public License +along with this program. If not, see . +*/ + +#ifndef CONFIG_H +#define CONFIG_H + +#include "config_common.h" + +/* USB Device descriptor parameter */ +#define VENDOR_ID 0xFEED +#define PRODUCT_ID 0x6060 +#define DEVICE_VER 0x0001 +#define MANUFACTURER Nobody +#define PRODUCT retro_refit +#define DESCRIPTION Retro Refit + +/* key matrix size */ +#define MATRIX_ROWS 11 +#define MATRIX_COLS 8 + +// See note in retro_refit.h for an explanation of how this matrix is wired up +#define MATRIX_ROW_PINS { D4, D7, B4, B5, B6, F7, F6, F5, F4, F1, F0 } +#define MATRIX_COL_PINS { B0, B1, B2, B3, D2, D3, C7, D5 } +#define UNUSED_PINS + +/* COL2ROW or ROW2COL */ +#define DIODE_DIRECTION COL2ROW + +/* define if matrix has ghost */ +//#define MATRIX_HAS_GHOST + +/* number of backlight levels */ +#define BACKLIGHT_LEVELS 0 + +/* Set 0 if debouncing isn't needed */ +#define DEBOUNCING_DELAY 5 + +/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ +#define LOCKING_SUPPORT_ENABLE +/* Locking resynchronize hack */ +#define LOCKING_RESYNC_ENABLE + + +/* Force NKRO Mode - If forced on, must be disabled via magic key (default = LShift+RShift+N) */ +#define FORCE_NKRO + +/* + * Magic key options + * These options allow the magic key functionality to be changed. This is useful + * if your keyboard/keypad is missing keys and you want magic key support. + */ + +/* key combination for magic key command */ +#define IS_COMMAND() ( \ + keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \ +) + +/* control how magic key switches layers */ +//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS true +//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS true +//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM false + +/* remap magic keys */ +//#define MAGIC_KEY_HELP1 H +//#define MAGIC_KEY_HELP2 SLASH +//#define MAGIC_KEY_DEBUG D +//#define MAGIC_KEY_DEBUG_MATRIX X +//#define MAGIC_KEY_DEBUG_KBD K +//#define MAGIC_KEY_DEBUG_MOUSE M +//#define MAGIC_KEY_VERSION V +//#define MAGIC_KEY_STATUS S +//#define MAGIC_KEY_CONSOLE C +//#define MAGIC_KEY_LAYER0_ALT1 ESC +//#define MAGIC_KEY_LAYER0_ALT2 GRAVE +//#define MAGIC_KEY_LAYER0 0 +//#define MAGIC_KEY_LAYER1 1 +//#define MAGIC_KEY_LAYER2 2 +//#define MAGIC_KEY_LAYER3 3 +//#define MAGIC_KEY_LAYER4 4 +//#define MAGIC_KEY_LAYER5 5 +//#define MAGIC_KEY_LAYER6 6 +//#define MAGIC_KEY_LAYER7 7 +//#define MAGIC_KEY_LAYER8 8 +//#define MAGIC_KEY_LAYER9 9 +//#define MAGIC_KEY_BOOTLOADER PAUSE +#define MAGIC_KEY_LOCK BSLS +//#define MAGIC_KEY_EEPROM E +//#define MAGIC_KEY_NKRO N +//#define MAGIC_KEY_SLEEP_LED Z + +/* + * Feature disable options + * These options are also useful to firmware size reduction. + */ + +/* disable debug print */ +//#define NO_DEBUG + +/* disable print */ +//#define NO_PRINT + +/* disable action features */ +//#define NO_ACTION_LAYER +//#define NO_ACTION_TAPPING +//#define NO_ACTION_ONESHOT +//#define NO_ACTION_MACRO +//#define NO_ACTION_FUNCTION + +#endif diff --git a/keyboards/handwired/retro_refit/keymaps/default/keymap.c b/keyboards/handwired/retro_refit/keymaps/default/keymap.c new file mode 100644 index 000000000..405402d5e --- /dev/null +++ b/keyboards/handwired/retro_refit/keymaps/default/keymap.c @@ -0,0 +1,33 @@ +// This is the canonical layout file for the Quantum project. If you want to add another keyboard, +// this is the style you want to emulate. + +#include "retro_refit.h" + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { +[0] = + KEYMAP( ESC, F1, F2, F3, F4, F5, F6, F7, F8, F9, F10, NLCK, SLCK, PSCR, PAUS, \ + GRV, 1, 2, 3, 4, 5, 6, 7, 8, 9, 0, MINS, EQL, BSPC, HOME, \ + TAB, Q, W, E, R, T, Y, U, I, O, P, LBRC, RBRC, PGUP, \ + BSLS, A, S, D, F, G, H, J, K, L, SCLN, QUOT, ENT, PGDN, \ + LSFT, Z, X, C, V, B, N, M, COMM, DOT, SLSH, RSFT, UP, END, \ + LCTL, LGUI, LALT, SPC, INS, DEL, LEFT, DOWN, RGHT), +}; + +const uint16_t PROGMEM fn_actions[] = { + +}; + +const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt) +{ + // MACRODOWN only works in this function + switch(id) { + case 0: + if (record->event.pressed) { + register_code(KC_RSFT); + } else { + unregister_code(KC_RSFT); + } + break; + } + return MACRO_NONE; +}; diff --git a/keyboards/handwired/retro_refit/readme.md b/keyboards/handwired/retro_refit/readme.md new file mode 100644 index 000000000..9f10edf9f --- /dev/null +++ b/keyboards/handwired/retro_refit/readme.md @@ -0,0 +1,60 @@ +retro_refit keyboard firmware +====================== + +## Keyboard Info + +The retro refit keyboard used a Teensy to replace the original controller on a 386 "laptop". + +http://imgur.com/a/08Fyj + +This keyboard uses a KEYMAP macro that is a great example of using a non-standard row-column matrix. The keyboard in question had 11 rows and 8 columns, but the rows were not all horizontal, and the columns were not all vertical. For example, row 2 contained "Print Screen", "N", "M", ",", ".", "/", "Right Shift", and"Left Alt". Column 0 contained "F6", "7", "O", "'", "Q", "D", "B", "Left Alt", "Up Arrow", and "Down Arrow". + +The macro makes programming the keys easier and in a more straight-forward manner because it realigns the keys into a 6x15 sensible keyboard layout instead of the obtuse 11x8 matrix. Each Kxy corrisponds to a key in row x column y. + +``` +#define KEYMAP( \ + K77, K05, K04, K03, K02, K01, K00, KA7, KA6, KA5, KA4, KA3, KA2, K11, K94, \ + K27, K76, K75, K74, K73, K72, K71, K70, K67, K66, K65, K64, K63, K62, KA1, \ + K61, K60, K57, K56, K55, K54, K53, K52, K51, K50, K47, K46, K45, K97, \ + K43, K42, K41, K40, K37, K36, K35, K34, K33, K32, K31, K30, K44, K87, \ + K26, K24, K23, K22, K21, K20, K17, K16, K15, K14, K13, K12, KA0, K91, \ + K10, K06, K25, K07, K86, K85, K95, K90, K93 \ +) { \ +{ KC_##K00, KC_##K01, KC_##K02, KC_##K03, KC_##K04, KC_##K05, KC_##K06, KC_##K07, }, \ +{ KC_##K10, KC_##K11, KC_##K12, KC_##K13, KC_##K14, KC_##K15, KC_##K16, KC_##K17, }, \ +{ KC_##K20, KC_##K21, KC_##K22, KC_##K23, KC_##K24, KC_##K25, KC_##K26, KC_##K27, }, \ +{ KC_##K30, KC_##K31, KC_##K32, KC_##K33, KC_##K34, KC_##K35, KC_##K36, KC_##K37, }, \ +{ KC_##K40, KC_##K41, KC_##K42, KC_##K43, KC_##K44, KC_##K45, KC_##K46, KC_##K47, }, \ +{ KC_##K50, KC_##K51, KC_##K52, KC_##K53, KC_##K54, KC_##K55, KC_##K56, KC_##K57, }, \ +{ KC_##K60, KC_##K61, KC_##K62, KC_##K63, KC_##K64, KC_##K65, KC_##K66, KC_##K67, }, \ +{ KC_##K70, KC_##K71, KC_##K72, KC_##K73, KC_##K74, KC_##K75, KC_##K76, KC_##K77, }, \ +{ KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_##K85, KC_##K86, KC_##K87, }, \ +{ KC_##K90, KC_##K91, KC_NO, KC_##K93, KC_##K94, KC_##K95, KC_NO, KC_##K97, }, \ +{ KC_##KA0, KC_##KA1, KC_##KA2, KC_##KA3, KC_##KA4, KC_##KA5, KC_##KA6, KC_##KA7, } \ +} +``` + + +## Quantum MK Firmware + +For the full Quantum feature list, see [the parent readme.md](/readme.md). + +## Building + +Download or clone the whole firmware and navigate to the keyboards/retro_refit folder. Once your dev env is setup, you'll be able to type `make` to generate your .hex - you can then use the Teensy Loader to program your .hex file. + +Depending on which keymap you would like to use, you will have to compile slightly differently. + +### Default +To build with the default keymap, simply run `make default`. + +### Other Keymaps +Several version of keymap are available in advance but you are recommended to define your favorite layout yourself. To define your own keymap create file named `.c` and see keymap document (you can find in top readme.md) and existent keymap files. + +To build the firmware binary hex file with a keymap just do `make` with a keymap like this: + +``` +$ make [default|jack|] +``` + +Keymaps follow the format **__\.c__** and are stored in the `keymaps` folder. \ No newline at end of file diff --git a/keyboards/handwired/retro_refit/retro_refit.c b/keyboards/handwired/retro_refit/retro_refit.c new file mode 100644 index 000000000..3d610eba3 --- /dev/null +++ b/keyboards/handwired/retro_refit/retro_refit.c @@ -0,0 +1,47 @@ +#include "retro_refit.h" +#include "led.h" + +void matrix_init_kb(void) { + // put your keyboard start-up code here + // runs once when the firmware starts up + + // Disable status LED on KB, enable status LED on Teensy (KB_STATUS = !TEENSY_STATUS) + DDRD |= (1<<6); + PORTD |= (1<<6); + + matrix_init_user(); +}; + +void led_set_kb(uint8_t usb_led) { + // put your keyboard LED indicator (ex: Caps Lock LED) toggling code here + + if (usb_led & (1< - -This program is free software: you can redistribute it and/or modify -it under the terms of the GNU General Public License as published by -the Free Software Foundation, either version 2 of the License, or -(at your option) any later version. - -This program is distributed in the hope that it will be useful, -but WITHOUT ANY WARRANTY; without even the implied warranty of -MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -GNU General Public License for more details. - -You should have received a copy of the GNU General Public License -along with this program. If not, see . -*/ - -#ifndef CONFIG_H -#define CONFIG_H - -#include "config_common.h" - -/* USB Device descriptor parameter */ -#define VENDOR_ID 0xFEED -#define PRODUCT_ID 0x6060 -#define DEVICE_VER 0x0001 -#define MANUFACTURER Nobody -#define PRODUCT retro_refit -#define DESCRIPTION Retro Refit - -/* key matrix size */ -#define MATRIX_ROWS 11 -#define MATRIX_COLS 8 - -// See note in retro_refit.h for an explanation of how this matrix is wired up -#define MATRIX_ROW_PINS { D4, D7, B4, B5, B6, F7, F6, F5, F4, F1, F0 } -#define MATRIX_COL_PINS { B0, B1, B2, B3, D2, D3, C7, D5 } -#define UNUSED_PINS - -/* COL2ROW or ROW2COL */ -#define DIODE_DIRECTION COL2ROW - -/* define if matrix has ghost */ -//#define MATRIX_HAS_GHOST - -/* number of backlight levels */ -#define BACKLIGHT_LEVELS 0 - -/* Set 0 if debouncing isn't needed */ -#define DEBOUNCING_DELAY 5 - -/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ -#define LOCKING_SUPPORT_ENABLE -/* Locking resynchronize hack */ -#define LOCKING_RESYNC_ENABLE - - -/* Force NKRO Mode - If forced on, must be disabled via magic key (default = LShift+RShift+N) */ -#define FORCE_NKRO - -/* - * Magic key options - * These options allow the magic key functionality to be changed. This is useful - * if your keyboard/keypad is missing keys and you want magic key support. - */ - -/* key combination for magic key command */ -#define IS_COMMAND() ( \ - keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \ -) - -/* control how magic key switches layers */ -//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS true -//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS true -//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM false - -/* remap magic keys */ -//#define MAGIC_KEY_HELP1 H -//#define MAGIC_KEY_HELP2 SLASH -//#define MAGIC_KEY_DEBUG D -//#define MAGIC_KEY_DEBUG_MATRIX X -//#define MAGIC_KEY_DEBUG_KBD K -//#define MAGIC_KEY_DEBUG_MOUSE M -//#define MAGIC_KEY_VERSION V -//#define MAGIC_KEY_STATUS S -//#define MAGIC_KEY_CONSOLE C -//#define MAGIC_KEY_LAYER0_ALT1 ESC -//#define MAGIC_KEY_LAYER0_ALT2 GRAVE -//#define MAGIC_KEY_LAYER0 0 -//#define MAGIC_KEY_LAYER1 1 -//#define MAGIC_KEY_LAYER2 2 -//#define MAGIC_KEY_LAYER3 3 -//#define MAGIC_KEY_LAYER4 4 -//#define MAGIC_KEY_LAYER5 5 -//#define MAGIC_KEY_LAYER6 6 -//#define MAGIC_KEY_LAYER7 7 -//#define MAGIC_KEY_LAYER8 8 -//#define MAGIC_KEY_LAYER9 9 -//#define MAGIC_KEY_BOOTLOADER PAUSE -#define MAGIC_KEY_LOCK BSLS -//#define MAGIC_KEY_EEPROM E -//#define MAGIC_KEY_NKRO N -//#define MAGIC_KEY_SLEEP_LED Z - -/* - * Feature disable options - * These options are also useful to firmware size reduction. - */ - -/* disable debug print */ -//#define NO_DEBUG - -/* disable print */ -//#define NO_PRINT - -/* disable action features */ -//#define NO_ACTION_LAYER -//#define NO_ACTION_TAPPING -//#define NO_ACTION_ONESHOT -//#define NO_ACTION_MACRO -//#define NO_ACTION_FUNCTION - -#endif diff --git a/keyboards/retro_refit/keymaps/default/keymap.c b/keyboards/retro_refit/keymaps/default/keymap.c deleted file mode 100644 index 405402d5e..000000000 --- a/keyboards/retro_refit/keymaps/default/keymap.c +++ /dev/null @@ -1,33 +0,0 @@ -// This is the canonical layout file for the Quantum project. If you want to add another keyboard, -// this is the style you want to emulate. - -#include "retro_refit.h" - -const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { -[0] = - KEYMAP( ESC, F1, F2, F3, F4, F5, F6, F7, F8, F9, F10, NLCK, SLCK, PSCR, PAUS, \ - GRV, 1, 2, 3, 4, 5, 6, 7, 8, 9, 0, MINS, EQL, BSPC, HOME, \ - TAB, Q, W, E, R, T, Y, U, I, O, P, LBRC, RBRC, PGUP, \ - BSLS, A, S, D, F, G, H, J, K, L, SCLN, QUOT, ENT, PGDN, \ - LSFT, Z, X, C, V, B, N, M, COMM, DOT, SLSH, RSFT, UP, END, \ - LCTL, LGUI, LALT, SPC, INS, DEL, LEFT, DOWN, RGHT), -}; - -const uint16_t PROGMEM fn_actions[] = { - -}; - -const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt) -{ - // MACRODOWN only works in this function - switch(id) { - case 0: - if (record->event.pressed) { - register_code(KC_RSFT); - } else { - unregister_code(KC_RSFT); - } - break; - } - return MACRO_NONE; -}; diff --git a/keyboards/retro_refit/readme.md b/keyboards/retro_refit/readme.md deleted file mode 100644 index 77df861ce..000000000 --- a/keyboards/retro_refit/readme.md +++ /dev/null @@ -1,26 +0,0 @@ -retro_refit keyboard firmware -====================== - -## Quantum MK Firmware - -For the full Quantum feature list, see [the parent readme.md](/readme.md). - -## Building - -Download or clone the whole firmware and navigate to the keyboards/retro_refit folder. Once your dev env is setup, you'll be able to type `make` to generate your .hex - you can then use the Teensy Loader to program your .hex file. - -Depending on which keymap you would like to use, you will have to compile slightly differently. - -### Default -To build with the default keymap, simply run `make default`. - -### Other Keymaps -Several version of keymap are available in advance but you are recommended to define your favorite layout yourself. To define your own keymap create file named `.c` and see keymap document (you can find in top readme.md) and existent keymap files. - -To build the firmware binary hex file with a keymap just do `make` with a keymap like this: - -``` -$ make [default|jack|] -``` - -Keymaps follow the format **__\.c__** and are stored in the `keymaps` folder. \ No newline at end of file diff --git a/keyboards/retro_refit/retro_refit.c b/keyboards/retro_refit/retro_refit.c deleted file mode 100644 index 3d610eba3..000000000 --- a/keyboards/retro_refit/retro_refit.c +++ /dev/null @@ -1,47 +0,0 @@ -#include "retro_refit.h" -#include "led.h" - -void matrix_init_kb(void) { - // put your keyboard start-up code here - // runs once when the firmware starts up - - // Disable status LED on KB, enable status LED on Teensy (KB_STATUS = !TEENSY_STATUS) - DDRD |= (1<<6); - PORTD |= (1<<6); - - matrix_init_user(); -}; - -void led_set_kb(uint8_t usb_led) { - // put your keyboard LED indicator (ex: Caps Lock LED) toggling code here - - if (usb_led & (1<