| Age | Commit message (Collapse) | Author |
|---|
|
This creates a helper function called "gas_volume()" that takes the
cylinder and a particular pressure, and returns the estimated volume of
the gas at surface pressure, including proper approximation of the
incompressibility of gas.
It very much is an approximation, but it's closer to reality than
assuming a pure ideal gas. See for example compressibility at
http://en.wikipedia.org/wiki/Compressibility_factor
Suggested-by: Jukka Lind <jukka.lind@iki.fi>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
|
|
Uses profile.c:evn_foreach() to retrieve the number of events, which
if zero, no table is added in the dialog and the label is added instead.
Signed-off-by: Lubomir I. Ivanov <neolit123@gmail.com>
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
|
|
Commit 90d3c5614a9c ("Centralising and redefining values as integers")
broke SAC-rate calculations. In particular, it changed "to_ATM()": to
use the centralized SURFACE_PRESSURE helper define, but in the process
it changed a floating point calculation to an integer calculation, and
it threw away all the fractional details. Any user of "to_ATM()"
basically dropped to an accuracy of a single atmosphere.
The good news is that we didn't use to_ATM() for things like depth
calculations, but only for cylinder pressures. As a result, the error
ends up being relatively small, since the pressures involved are big,
and thus the error of rounding to whole atmospheres is usually in the
1% range. The cylinder sizing tends to be off by more than that
anyway. But it was wrong, and not intentional.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
|
|
And report error if XSLT stylesheet not found
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
|
|
This does a final pass after all the selection logic, and notices if we
have dive trips that are selected, but that have no dives in them
selected. In that case, we assume that the user wanted to select all
dives in that trip.
NOTE! This still allows a range selection that selects the dive trip
entry and a few dives under the trip. If a trip has any dives selected
in it, we leave that manual selection alone. So this new logic really
only triggers on the case where somebody selected *just* the trip.
Note: unselecting the trip still leaves the dives under it selected,
because having a dive trip that isn't selected have all the dives under
it be selected is normal, and we can't recognize that as some kind of
special event.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
|
|
..they are of a higher quality anyway, and this way we have one less
library to worry about. And this way there is nobody who can claim that
openssl is not a system library and thus not compatible with the GPL.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
|
|
Better helper functions make for easier to understand code.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
|
|
We now load and save this in the XML file, we do the right thing when
merging dives and show the edited air temperature in the Dive Info
notebook when a divecomputer doesn't have an air temperature.
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
|
|
Printf is not a way to issue warnings and errors. This is a very late
addition but seems necessary for a viable release of the planner.
This also adds one artificial limit and two warnings:
a) no dives deeper than 400m
b) warning of potentially very long calculation times for dives longer
than 3h (180min) before the ascent and dives deeper than 150m
It also creates quite a number of new strings that need to be translated
(and marks a few existing ones for translation as well).
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
|
|
Two separate bugs.
a) Air cylinders were created with o2=209 and no other value set.
sanitize_gasmix() turned that into o2=0 which meant that this cylinder was
now identified as "nodata", i.e., unset.
We now set a fake cylinder name to deal with that issue.
b) the gaschange event is inherited from libdivecomputer and therefore
only supports 1 percent granularity for o2 and h2. Since we didn't round
when assigning the value we ended up with air being stored as o2=20 he=0
which of course then didn't match air anymore (which we have defined as
208 <= o2 <= 210).
We now use o2=210 for air in the planner and carefully round the permille
values whenever we convert into percent - and compare gases with percent
granularity as well.
A better fix for b) would be to change the Subsurface event to not simply
copy the libdivecomputer behavior and use percent granularity but support
permille instead. But this closely before the 3.0 release that seemed like
a far too invasive change to make - the changes to the planner should have
no impact outside the planner module.
Reported-by: Chris Lewis <chrislewis915@gmail.com>
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
|
|
This adds watertemp and airtemp to the dive, populates them in fixup and
uses them elsewhere in the code.
WARNING: as a sideeffect we now edit the airtemp in the dive, but we never
display this in the DIve Info notebook (as that always displays the data
from the specific selected divecomputer). This is likely to cause
confusion. It's consistent behavior, but... odd. This brings back the
desire to have a view of "best data available" for a dive, in addition to
the "per divecomputer" view. This would also allow us to consolidate the
different pressure graphs we may be getting from different divecomputers
(consider the case where you dive with multiple air integrated computers
that are connected to different tanks - now we could have one profile with
all the correct tank pressure plots overlayed - and the best available (or
edited) data in the corresponding Dive Info notebook.
This commit also fixes a few remaining accesses to the first divecomputer
that fell through the cracks earlier and does a couple of other related
cleanups.
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
|
|
When starting on this quest to stop using the first divecomputer instead
of data for the whole dive in commit eb73b5a528c8 ("Duration of a dive is
the maximum duration from all divecomputers") I introduced an accessor
function that calculates the dive duration on the fly as the maximum of
the durations in the divecomputers.
Since then Linus and I have added quite a few of the variables back to the
dive data structure and it makes perfect sense to do the same thing for
the duration as well and simply do the calculation once during fixup.
This commit also replaces accesses to the first divecomputer in
likely_same_dive to use the maxdepth and meandepth of the dive (those two
slipped through the cracks in the previous commits, it seems).
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
|
|
This is currently only used in one place (in statistics.c), but it
certainly is consistent with the other recent changes to avoid using only
the first divecomputer when trying to make statements about a dive.
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
|
|
Populate during dive fixup as the maximum depth shown by all the
divecomputers. Use this value (instead of the one in the first
divecomputer) in printing, statistics, etc.
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
|
|
In commit b6c9301e5847 ("Move more dive computer filled data to the
divecomputer structure") we moved the fields that get filled in by the
dive computers to be per-divecomputer data structures.
This patch re-creates some of those fields back in the "struct dive",
but now the fields are initialized to be a reasonable average from the
dive computer data. We already did some of this for the temperature
min/max fields for the statistics, so this just continues that trend.
The goal is to make it easy to look at "dive values" without having to
iterate over dive computers every time you do. Just do it once in
"fixup_dive()" instead.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
|
|
There are two ways to look at surface pressure. One is to say "what was
the surface pressure during that dive?" - in that case we now return an
average over the pressure reported by the different divecomputers (or the
standard 1013mbar if none reported any).
Or you want to do specific calculations for a specific divecomputer - in
which case we access only the pressure reported by THAT divecomputer, if
present (and fall back to the previous case, otherwise).
We still have lots of places in Subsurface that only act on the first
divecomputer. As a side effect of this change we now make this more
obvious as we in those cases pass a pointer to the first divecomputer
explicitly to the calculations.
Either way, this commit should prevent us from ever mistakenly basing our
calculations on a surface pressure of 0 (which is the initial bug in
deco.c that triggered all this).
Similar changes need to be made for other elements that we currently only
use from the first divecomputer, i.e., salinity.
Reported-by: Robert C. Helling <helling@atdotde.de>
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
|
|
We'll want to use a 'static const' gasmix for the upcoming no-fly-time
code, so prepare for it by just marking the read-only gasmix argument as
'const'.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
|
|
So far we always used the duration of the first divecomputer. The same fix
needs to be done for some of the other calculations that always use the
first divecomputer.
This commit also removes some obsolete code from the webservice merging.
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
|
|
We had this special logic to not show the end of a dive when a dive
computer shows a series of very shallow samples (basically snorkeling
back to shore after the dive ended). However, that logic ended up being
global per dive, which is very annoying when you have two or more dive
computers, and it decides to cut off the second one because the first
one surfaces.
So get rid of this per-dive state, and just use the plot-info 'maxtime'
field for this (we never used the 'start' case anyway). That way we
will properly cut off boring surface entries only when they are past the
end of the interesting entries of *all* dive computers, and we won't be
cutting things short.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
|
|
This moves some double/floating handling for po2 to plain integer. There
are still non int values around (also for phe and po2) in the plot area.
Signed-off-by: Jan Schubert <Jan.Schubert@GMX.li>
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
|
|
Something which is nice especially when asked on the list to share an
interesting dive is the possibility to save just some dives into a file.
This commit adds to the context menu shown with right-click the 'Save As'
entry. This entry allows to save selected dives.
[Dirk Hohndel: clean up white space, commit message and remove unused
variables]
Signed-off-by: Pierre-Yves Chibon <pingou@pingoured.fr>
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
|
|
When the data file is closed we should reset the events that we offer for
filtering.
Reported-by: Sergey Starosek <sergey.starosek@gmail.com>
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
|
|
This no longer abuses the dive merging code (which would leave stray
"dives" behind if a gps fix couldn't be merged with any of the dives) and
instead parses the gps fixes into a second table and then walks that table
and tries to find matching dives.
The code tries to be reasonably smart about this. If we have
auto-generated GPS fixes at regular intervals, we look for a fix that is
during a dive (that's likely when the boat where the phone is staying dry
is more or less above the diver having fun). And if we have named entries
(so the user typed in a location name) we try to match them in order to
the dives that happened "that day" (where "that day" is about 6h before
and after the timestamp of the gps fix).
This commit also renames dive_has_location() to dive_has_gps_location() as
the difference between if(!dive->location) and if(dives_has_location) is a
bit too subtle...
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
|
|
This only changes the infrastructure and actually loses functionality as
it no longer does the simplistic "just treat the locations as dives and
merge them".
The new code that does something "smart" with the gps_location_table is
yet to be written. But now we can use the XML parser to put the gps
locations downloaded from the webservice into their own data structure.
In the process I noticed that we never used the two delete functions in
parse-xml.c and removed them.
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
|
|
It's only used by the Uemis importer, and Dirk always seems to import
his Uemis data first, so it wasn't very noticeable. But if the Uemis
data wasn't the first dive computer, it would not find the dive.
Side note: just comparing deviceid is not correct. We should pass in
the device model too. But again, that will realistically never really
matter, since non-Uemis importers will generate complex SHA1 hashes of
the dive data for the dive ID, so a collision with the Uemis numbers is
very unlikely.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
|
|
Mostly coding style and whitespace changes plus making lots of functions
static that have no need to be extern. This also helped find a bit of code
that is actually no longer used.
This should have absolutely no functional impact - all changes should be
purely cosmetic. But it removes a bunch of lines of code and makes the
rest easier to read.
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
|
|
This misses a single issue to be used as a base for further discussion:
The CC setpoint is used for the next segment, not the one specified for. I
also have in mind to modify the existing code to use setpoints specified
in mbar and plain integer instead of float values.
Signed-off-by: Jan Schubert <Jan.Schubert@GMX.li>
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
|
|
I have some concerns about the way this is implemented - especially the
use of gtk_grab_add to make the map widget work has me worried. But it
seems to work and survived some test cases that I threw at it.
The GtkButton with the Pixmap looks a little off on my screen, but this
way it was easy to implement. Feel free to come up with a better design.
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
|
|
I'm sure there are better ways to do this, but this appears to grok most
rational formats I was able to find. NSEW or positive/negative numbers.
Decimal degrees (WGS84) or degrees and decimal minutes (that's what most
GPSs seem to provide). I'm sure there are still corner cases that confuse
it, but it seemed reasonably robust in testing.
I don't really love the ';' as separator but that solves the obvious
problem with locales that use a decimal comma.
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
|
|
This centralizes all occurrences of Kelvin to dive.h and standardizes all
usages to milliKelvin.
[Dirk Hohndel: renamed the constant plus minor white space cleanup]
Signed-off-by: Jan Schubert <Jan.Schubert@GMX.li>
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
|
|
The statistics page only used each dive's "watertemp" attribute,
regardless of actual higher/lower temperatures in the samples. By
finding the actual max/min temperatures, the statistics page utilize
more "real" data, and look better even on single dives.
Signed-off-by: Henrik Brautaset Aronsen <subsurface@henrik.synth.no>
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
|
|
We save the (more complete) dive computer information in the XML file
with serial numbers and firmware version if we know about them, so using
a complicated string in the system config was redundant and confusing.
So remove that code.
NOTE! Since the dive computer nicknames are now only saved if the XML
file is saved, we also mark the dive list "changed" when we edit the
nicknames. That way we'll be prompted to save things before exiting,
even if we don't actually edit any actual dive data.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
|
|
We used to save dive computer information only if that dive computer was
actually used in any of the dives we saved. But we can simplify the
code if we just always save any dive computers we know about. And it
does allow for some usage cases where you have nicknames for other
peoples computers that you may not actively use, but you want to see if
you end up loading multiple XML files in one go.
So there's just no compelling reason to not just save all the info we
have. And this will make it less painful to remove the "use system
config for dive computer nicknames", because you can also use this to
continue to gather dive computer info in a separate XML file if you want
to.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
|
|
Temperatures can actually be negative, which means that rounding by
adding 0.5 and casting to 'int' is not correct.
We could use '(int)(rint(val))' instead, but the only place we care
about might as well just print out the floating point representation
with a precision of two digits instead. So if you have a dive computer
that gives you the precision, you might see '3.5˚C' as the temperature.
Remove the helper functions that nobody uses and that get the rounding
wrong anyway.
Reported-by: Henrik Brautaset Aronsen <subsurface@henrik.synth.no>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
|
|
This moves the fields 'duration', 'surfacetime', 'maxdepth',
'meandepth', 'airtemp', 'watertemp', 'salinity' and 'surface_pressure'
to the per-divecomputer data structure. They are filled in by the dive
computer, and normally not edited.
NOTE! All actual *use* of this data was then changed from dive->field to
dive->dc.field programmatically with a shell-script and sed, and the
result then edited for details. So while the XML save and restore code
has been updated, all the displaying etc will currently always just show
the first dive computer entry.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
|
|
This adds the "Show in map" menu entry to the divelist only if we
actually have a location to show.
Of course, having some way to visually see whether we have a GPS
location even before we show the menu would probably be good. Maybe a
marker in the "location" string or something. But in the meanwhile, at
least we don't have that menu entry if we have nothing to show.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
|
|
This adds a "Show in map" entry in the dive list context menu. It will
zoom to the dive location if it exists, otherwise the full map will be
displayed.
I've also switched map tiles from OpenStreetMap to Google Maps just to
show off that we can.
Signed-off-by: Henrik Brautaset Aronsen <subsurface@henrik.synth.no>
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
|
|
This makes it easy to print out a dive plan - it's simply stored in the
notes of the simulated dive we create.
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
|
|
This just provides the infrastructure to enter the data, nothing is
calculated, yet.
This adds a new get_thousandths() helper function so we can enter
information of the 'mili-' type as decimal values. So things like
"14.5 l/min" or "0.75 cuft/min" are parsed correctly and converted
into a ml value.
In the process of implementing that I also fixed a bug introduced in
commit ab7aecf16e96 ("Simplify dive planning code") which broke the
get_tenth() function.
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
|
|
Opening URI addresses from Subsurface does not work on Windows using
the latest GTK bundle from the Gnome website. The reason lies in GIO
and GLib and how it obtains assigned applications for protocols and MIME
types.
While gtk_show_uri() should be viable for both linux.c and macos.c,
in windows.c ShellExecute() is used, which provides proper support
for the URI calls.
subsurface_launch_for_uri() returns TRUE on success.
Signed-off-by: Lubomir I. Ivanov <neolit123@gmail.com>
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
|
|
This patch centralizes the definition for surface pressure, oxygen in
air, (re)defines all such values as plain integers and adapts calculations.
It eliminates 11 (!) occurrences of definitions for surface pressure and
also a few for oxygen in air.
It also rewrites the calculation for EAD, END and EADD using the new
definitons, harmonizing it for OC and CC and fixes a bug for EADD OC
calculation.
And finally it removes the unneeded variable entry_ead in gtk-gui.c.
Jan
Signed-off-by: Jan Schubert <Jan.Schubert@GMX.li>
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
|
|
- MOD: Maximum Operation Depth based on a configurable limit
- EAD: Equivalent Air Depth considering N2 and (!) O2 narcotic
- END: Equivalent Nitrogen (Narcotic) Depth considering just N2 narcotic
(ignoring O2)
- EADD: Equivalent Air Density Depth
Please note that some people and even diving organisations have opposite
definitions for EAD and END. Considering A stands for Air, lets choose the
above. And considering N for Nitrogen it also fits in this scheme.
This patch moves N2_IN_AIR from deco.c to dive.h as this is already used
in several places and might be useful for future use also. It also
respecifies N2_IN_AIR to a more correct value of 78,084%, the former one
also included all other gases than oxygen appearing in air. If someone
needs to use the former value it would be more correct to use 1-O2_IN_AIR
instead.
Signed-off-by: Jan Schubert / Jan.Schubert@GMX.li
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
|
|
For each dive recorded, place their GPS coordinates onto a map using the
OSM-GPS-MAP library.
This map is accessible via the "log" menu or the shortcut ctrl+M (M as map).
We check for the GPS coordinates "0, 0" which are the default when we do not
have real GPS coordinates set.
[Dirk Hohndel: fixed int/float math confusion, fixed some whitespace and
coding style issues, cleaned up some comments, added a
missing cast to prevent a compiler warning]
Signed-off-by: Pierre-Yves Chibon <pingou@pingoured.fr>
Signed-Off-By: Henrik Brautaset Aronsen <subsurface@henrik.synth.no>
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
|
|
.. and add the usual logic to not save the default values.
This also simplifies the initial system-specific setup of both of these:
since we have defaults for all the preferences that get set up at
startup, we can just initialize those defaults to the system-specific
fonts then and there.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
|
|
.. and rename the badly named 'output_units/input_units' variables.
We used to have this confusing thing where we had two different units
(input vs output) that *look* like they are mirror images, but in fact
"output_units" was the user units, and "input_units" are the XML parsing
units.
So this renames them to be clearer. "output_units" is now just "units"
(it's the units a user would ever see), and "input_units" is now
"xml_parsing_units" and set by the XML file parsers to reflect the units
of the parsed file.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
|
|
The legacy nickname wrappers (that use the device_info structure) are
left in gtk-gui.c. We can slowly start moving away from them, we don't
want to start exporting that thing as some kind of generic interface.
This isn't a pure code movement - because we leave the legacy interfaces
alone, there are a few new interfaces in device.c (like "create a new
device_info entry") that were embedded into the legacy "create nickname"
code, and needed to be abstracted out.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
|
|
We have several places where we interpolate the depth based on two
samples and the time between them. Some of them use floating point, some
of them don't, some of them meant to do it but didn't.
Just use a common helper function for it. I seriously doubt the floating
point here really matters, since doing it in integers is not going to
overflow unless we're interpolating between two samples that are hours
apart at hundreds of meters of depth, but hey, it gives that rounding to
the nearest millimeter. Which I'm sure matters.
Anyway, we can probably just get rid of the rounding and the floating
point math, but it won't really hurt either, so at least do it
consistently.
The interpolation could be for other things than just depth, but we
probably don't have anything else we'd want to interpolate. But make the
function naming generic just in case.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
|
|
o) Instead of using gradient factors as means of comparison, I now use
pressure (as in: maximal ambient pressure).
o) tissue_tolerance_calc() now computes the maximal ambient pressure now
respecting gradient factors. For this, it needs to know about the
surface pressure (as refernce for GF_high), thus gets *dive as an
argument. It is called from add_segment() which this also needs *dive
as an additional argument.
o) This implies deco_allowed_depth is now mainly a ambient-pressure to
depth conversion with decorations to avoid negative depth (i.e. no deco
obliation), implementation of quantization (!smooth => multiples of 3m)
and explicit setting of last deco depth (e.g. 6m for O2 deco).
o) gf_low_pressure_this_dive (slight change of name), the max depth in
pressure units is updated in add_segment. I set the minimal value in
buehlmann_config to the equivalent of 20m as otherwise good values of
GF_low add a lot of deco to shallow dives which do not need deep stops
in the first place.
o) The bogus loop is gone as well as actual_gradient_limit() and
gradient_factor_calculation() and large parts of deco_allowed_depth()
although I did not delete the code but put it in comments.
o) The meat is in the formula in lines 147-154 of deco.c. Here is the
rationale:
Without gradient factors, the M-value (i.e the maximal tissue pressure)
at a given depth is given by ambient_pressure / buehlmann_b + a.
According to "Clearing Up The Confusion About "Deep Stops" by Erik C.
Baker (as found via google) the effect of the gradient factors is no
replace this by a reduced affine relation (i.e. another line) such that
at the surface the difference between M-value and ambient pressure is
reduced by a factor GF_high and at the maximal depth by a factor
GF_low.
That is, we are looking for parameters alpha and beta such that
alpha surface + beta = surface + gf_high * (surface/b + a - surface)
and
alpha max_p + beta = max_p + gf_low * (max_p/b + a - max_p)
This can be solved for alpha and beta and then inverted to obtain the
max ambient pressure given tissue loadings. The result is the above
mentioned formula.
Signed-off-by: Robert C. Helling <helling@atdotde.de>
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
|
|
This was just a crutch to get something out there for people to play with.
With the ability to input a plan in place this is now obsolete.
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
|
|
This had gotten lost when updating the profile on the fly.
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
|
Linus Torvalds
Lubomir I. Ivanov
Dirk Hohndel
Jan Schubert
Pierre-Yves Chibon
Henrik Brautaset Aronsen
Robert C. Helling