From d0b26c6e57a3f5acc8c1b09a06405fc7ba639612 Mon Sep 17 00:00:00 2001 From: Willem Ferguson Date: Thu, 10 Sep 2015 20:49:36 +0200 Subject: User manual update: Dive planner 1) Added text to reflect VPM-B dive planning 2) Replaced 5 images in dive planner chapter. Signed-off-by: Willem Ferguson Signed-off-by: Dirk Hohndel --- Documentation/user-manual.txt | 16 ++++++++++++---- 1 file changed, 12 insertions(+), 4 deletions(-) (limited to 'Documentation/user-manual.txt') diff --git a/Documentation/user-manual.txt b/Documentation/user-manual.txt index 9619cb292..d9f228137 100644 --- a/Documentation/user-manual.txt +++ b/Documentation/user-manual.txt @@ -2974,7 +2974,7 @@ it means that recreational dive limits are exceeded and either the dive duration Below is an image of a dive plan for a recreational dive at 30 metres. Although the no-deco limit (NDL) is 23 minutes, the duration of the dive is limited by the amount of air in the cylinder, reflected by the information in the -text box at the bottom right of the panel. +text box at the bottom right of the panel that requires sufficient air for buddy-sharing during the ascent. image::images/rec_diveplan.jpg["FIGURE: A recreational dive plan: setup",align="center"] @@ -2984,19 +2984,27 @@ Non-recreational dive planning involves exceeding the no-deco limits and/or usin Such dives are planned in three stages: *a) Nitrogen management*: This is performed by specifying the rates for descent and ascent, -as well as the gradient factors (GFLow and GFHigh) under the headings _Rates_ and _Planning_ -to the bottom left of the planning screen. Initially, the GFHigh and GFLow values in the _Preferences_ +as well as the deco model (GFLow, GFHigh or Conservatism level) under the headings _Rates_ and _Planning_ +to the bottom left of the planning screen. Two deco models are supported the Buehlmann model and the VPM-B +model. Select one of the two models. When selecting the Buehlmann model, the gradient factors (GF_high and GF_low +need to be specified. Initially, the GFHigh and GFLow values in the _Preferences_ panel of _Subsurface_ is used. If these are changed within the planner (see _Gas Options_ within the planner), the new values are used without changing the original values in the _Preferences_. Gradient Factor settings strongly affect the calculated ceilings and their depths. A very low GFLow value brings about decompression stops early on during the dive. ** For more information about Gradient factors, see the section on xref:S_GradientFactors[Gradient Factor Preference settings]. + +If the VPM-B model is selected, the Conservatism_level needs to be specified on a scale of 0 (least conservative) to 4 (most conservative). +This model tends to give deco stops at deeper levels than the Beuhlmann model and often results in slightly shorter +dive durations than the Buehlmann model. When selecting one of these models, keep in mind that they are NOT exact physiological models but +only mathematical models that appear to work in practice. + For more information external to this manual see: * link:http://www.tek-dive.com/portal/upload/M-Values.pdf[Understanding M-values by Erik Baker, _Immersed_ Vol. 3, No. 3.] * link:http://www.rebreatherworld.com/general-and-new-to-rebreather-articles/5037-gradient-factors-for-dummies.html[Gradient factors for dummies, by Kevin Watts] * link:http://www.amazon.com/Deco-Divers-Decompression-Theory-Physiology/dp/1905492073/ref=sr_1_1?s=books&ie=UTF8&qid=1403932320&sr=1-1&keywords=deco+for+divers[_Deco for Divers_, by Mark Powell (2008). Aquapress] Southend-on-Sea, UK. ISBN 10: 1-905492-07-3. -An excellent non-technical review. +An excellent non-technical review that discusses both the Buehlmann deco model and the VPM-B model. The ascent rate is critical for nitrogen off-gassing at the end of the dive and is specified for several depth ranges, utilising the average (or mean) depth as a yardstick. The mean depth -- cgit v1.2.3-70-g09d2