Cleanup rules.mk for 32U4 keyboards, A-F (#6804)

* Cleanup rules.mk for 32U4 keyboards, A-F

* Put back stuff in VIA keymaps

2 files changed, 13 insertions, 44 deletions

diff --git a/keyboards/aeboards/ext65/keymaps/via/rules.mk b/keyboards/aeboards/ext65/keymaps/via/rules.mk
index f072c6719..70258b9ea 100644
--- a/keyboards/aeboards/ext65/keymaps/via/rules.mk
+++ b/keyboards/aeboards/ext65/keymaps/via/rules.mk
@@ -1,6 +1,6 @@
 # project specific files
 SRC =	keyboards/wilba_tech/wt_main.c
-		
+
 # MCU name
 MCU = atmega32u4
 
@@ -65,4 +65,4 @@ AUDIO_ENABLE = no           # Audio output on port C6
 FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches
 
 RAW_ENABLE = yes
-DYNAMIC_KEYMAP_ENABLE = yes
\ No newline at end of file
+DYNAMIC_KEYMAP_ENABLE = yes
diff --git a/keyboards/aeboards/ext65/rules.mk b/keyboards/aeboards/ext65/rules.mk
index f1c632289..bac979ad0 100644
--- a/keyboards/aeboards/ext65/rules.mk
+++ b/keyboards/aeboards/ext65/rules.mk
@@ -1,50 +1,16 @@
-# project specific files
-SRC =	keyboards/wilba_tech/wt_main.c
-		
 # MCU name
 MCU = atmega32u4
 
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section
+# Bootloader selection
+#   Teensy       halfkay
+#   Pro Micro    caterina
+#   Atmel DFU    atmel-dfu
+#   LUFA DFU     lufa-dfu
+#   QMK DFU      qmk-dfu
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
 BOOTLOADER = atmel-dfu
 
-
 # Build Options
 #   change yes to no to disable
 #
@@ -63,3 +29,6 @@ UNICODE_ENABLE = no         # Unicode
 BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
 AUDIO_ENABLE = no           # Audio output on port C6
 FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches
+
+# project specific files
+SRC += keyboards/wilba_tech/wt_main.c