[Keyboard] Add keyboard Zenith Z-150 (#9811)

* z150 black pill

* z150 docs

* z150: json layout

* Update keyboards/handwired/z150/keymaps/zyxx/keymap.c

Co-authored-by: Joel Challis <git@zvecr.com>

* Update keyboards/handwired/z150/rules.mk

Co-authored-by: Joel Challis <git@zvecr.com>

* Update keyboards/handwired/z150/rules.mk

Co-authored-by: Joel Challis <git@zvecr.com>

* Update keyboards/handwired/z150/z150.c

Co-authored-by: Joel Challis <git@zvecr.com>

* Update keyboards/handwired/z150/config.h

Co-authored-by: Joel Challis <git@zvecr.com>

* Delete bootloader_defs.h

Useless file

* Update keyboards/handwired/z150/readme.md

Co-authored-by: Joel Challis <git@zvecr.com>

Co-authored-by: Joel Challis <git@zvecr.com>

1 files changed, 62 insertions, 0 deletions

diff --git a/keyboards/handwired/z150/readme.md b/keyboards/handwired/z150/readme.md
new file mode 100644
index 000000000..a1f0bef8f
--- /dev/null
+++ b/keyboards/handwired/z150/readme.md
@@ -0,0 +1,62 @@
+# QMK-based firmware for Zenith Z-150 keyboard
+
+![Z-150](https://imgur.com/jayyyvJ.jpg)
+
+Zenith Z-150 keyboard conversion project: direct connection of Black Pill to the matrix.
+
+* Keyboard Maintainer: [DmNosachev](https://github.com/DmNosachev)
+* Hardware Supported: [Zenith Z-150 keyboard, 100-1860 version with white logo](https://deskthority.net/wiki/Zenith_Z-150), Black Pill STM32F103C8T6 MCU board. Alternatevely you can use any MCU which is supported by QMK and has 22 or more IO pins: Arduino Micro, Teensy 2.0, Teensy 2.0++, Blue Pill, etc.
+
+Earlier 100-1886 version with black logo has different PCB.
+
+Make example for this keyboard (after setting up your build environment):
+
+    make handwired/z150:default
+
+See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).
+
+# Modding
+
+## Matrix
+
+Z-150 has 11x8 matrix. It's ghost-free thanks to the diodes.
+
+Columns are located under NEC D8049HC MCU IC:
+![Z-150 columns](https://imgur.com/XiOsrnh.jpg)
+
+Rows are connected to unmarked 24-pin MUX IC:
+![Z-150 rows](https://imgur.com/Wu8rHY0.jpg)
+
+## LEDs
+
+LEDs (from left to right): NumLock, CapsLock, ScrollLock:
+![Z-150 LED cathodes](https://imgur.com/MO5NLlZ.jpg)
+
+Their anodes are connected to VCC through 220Ω resistors.
+![Z-150 LED anodes](https://imgur.com/w1MfjRN.jpg)
+
+You can keep the original resistors, but with Black Pill or any other 3.3V controller the LEDs may seem a little dim. Try 150Ω or close value if you want to fix that.
+
+
+## Black Pill
+Suggested mount position for the Black Pill (view from the bottom side of the PCB):
+
+```
+      R0  R1  R2  R3  R4  R6          R9  LC  LN  LS
+,--------------------------------------------------------------------,
+|B12 B13 B14 B15  A8  A9 A10 A11 A12 A15  B3  B4  B5  B6  B7 3V3 GND |---,
+|                                                                    |USB|
+|B11 B10  B1  B0  A7  A6  A5  A4  A3  A2  A1  A0 RST C13  B9  B8 GND |---'
+'--------------------------------------------------------------------'
+  C0  C1  C2  C3  C4  C5  C6  C7  R5  R8  R7  RA    
+```
+
+
+1. Desolder all ICs, crystal oscillator, capacitors and resistors except R0–R2 (they connect LEDs to VCC).
+1. Solder 12-pin header to the Black Pill (pins B11–A0 on the left side).
+2. Solder two 3-pin headers for boot jumpers.
+3. Solder 4-pin SWD header.
+4. Burn [STM32duino bootloader](https://github.com/rogerclarkmelbourne/STM32duino-bootloader/blob/master/bootloader_only_binaries/generic_boot20_pb12.bin) to Black Pill.
+5. Compile and flash the firmware: `make handwired/z150:default:flash`
+5. Align Black Pill pins B11–A4 with columns 0–7 and solder them.
+6. Connect rows, LEDs, ground and VCC traces to the corresponding pins of the BlackPill using additional wires.