define new keyboard "Hecomi" (#5147)

* update pinout for matrix

* first commit

* include split_common.h

* change split_common.h to split_util.h

* update config.h

* update keymap & config

* update

* remove K70, add K77

* fixed test keymap

* add Layer

* define to HHKB pro 2 based keymap

* change authoer name

* define LAYOUT and LAYOUT_KC

* replace from LAYOUT_KC to LAYOUT

* change name hecomi_alpha to hecomi/alpha

* fixed hecomi_alpha to hecomi/alpha

* remove unnecessary files

* update readme

* add DEFAULT_FOLDER

* remove hecomi_alpha because change name to hecomi

* remove bad LAYOUT macro

* remove IS_COMMAND macro

* remove unnecessary RGB options

* Update keyboards/hecomi/hecomi.h

Co-Authored-By: takashiski <takashiskibb@gmail.com>

* Update keyboards/hecomi/hecomi.h

Co-Authored-By: takashiski <takashiskibb@gmail.com>

* Update keyboards/hecomi/alpha/rules.mk

Co-Authored-By: takashiski <takashiskibb@gmail.com>

* Update keyboards/hecomi/alpha/rules.mk

Co-Authored-By: takashiski <takashiskibb@gmail.com>

* Update keyboards/hecomi/hecomi.h

Co-Authored-By: takashiski <takashiskibb@gmail.com>

* remove endif

* update rule.mk with suggestions

1 files changed, 85 insertions, 0 deletions

diff --git a/keyboards/hecomi/rules.mk b/keyboards/hecomi/rules.mk
new file mode 100644
index 000000000..19b763d43
--- /dev/null
+++ b/keyboards/hecomi/rules.mk
@@ -0,0 +1,85 @@
+DEFAULT_FOLDER=hecomi/alpha
+#
+#
+# MCU name
+#MCU = at90usb1286
+MCU = atmega32u4
+
+# Processor frequency.
+#     This will define a symbol, F_CPU, in all source code files equal to the
+#     processor frequency in Hz. You can then use this symbol in your source code to
+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#     automatically to create a 32-bit value in your source code.
+#
+#     This will be an integer division of F_USB below, as it is sourced by
+#     F_USB after it has run through any CPU prescalers. Note that this value
+#     does not *change* the processor frequency - it should merely be updated to
+#     reflect the processor speed set externally so that the code can use accurate
+#     software delays.
+F_CPU = 16000000
+
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+
+# Bootloader selection
+#   Teensy       halfkay
+#   Pro Micro    caterina
+#   Atmel DFU    atmel-dfu
+#   LUFA DFU     lufa-dfu
+#   QMK DFU      qmk-dfu
+#   atmega32a    bootloadHID
+BOOTLOADER = caterina
+
+
+# If you don't know the bootloader type, then you can specify the
+# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
+#   Teensy halfKay      512
+#   Teensy++ halfKay    1024
+#   Atmel DFU loader    4096
+#   LUFA bootloader     4096
+#   USBaspLoader        2048
+# OPT_DEFS += -DBOOTLOADER_SIZE=4096
+
+
+# Build Options
+#   change yes to no to disable
+#
+BOOTMAGIC_ENABLE = yes      # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = yes       # Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
+CONSOLE_ENABLE = yes        # Console for debug(+400)
+COMMAND_ENABLE = yes        # Commands for debug and configuration
+# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
+SLEEP_LED_ENABLE = no       # Breathing sleep LED during USB suspend
+# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+NKRO_ENABLE = no            # USB Nkey Rollover
+BACKLIGHT_ENABLE = no       # Enable keyboard backlight functionality on B7 by default
+RGBLIGHT_ENABLE = no        # Enable keyboard RGB underglow
+MIDI_ENABLE = no            # MIDI support (+2400 to 4200, depending on config)
+UNICODE_ENABLE = no         # Unicode
+BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
+AUDIO_ENABLE = no           # Audio output on port C6
+FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches
+HD44780_ENABLE = no 		# Enable support for HD44780 based LCDs (+400)
+SPLIT_KEYBOARD = yes