[Keyboard] Update ATmega32A readme files to match template (#7462)

* Update atmega32a readme files to match template

* Update atmega32a readme files to match template - fixes

* Apply suggestions from code review

1 files changed, 10 insertions, 74 deletions

diff --git a/keyboards/jj50/README.md b/keyboards/jj50/README.md
index f7b8acc64..2d3e711be 100644
--- a/keyboards/jj50/README.md
+++ b/keyboards/jj50/README.md
@@ -1,83 +1,19 @@
-JJ50
-==========================
+# JJ50
 
-This is a port of the QMK firmware for boards that are based on the
-ps2avrGB firmware, like the [ps2avrGB keyboard](https://www.keyclack.com/product/gb-ps2avrgb/), for use on the JJ50, a preonic-like board.
+A preonic-like board
 
-Most of the code was taken and amended from YMD96, which in itself was taken from ps2avrGB and amended by Andrew Novak.
-
-Note that this is a complete replacement for the firmware, so you won't be
-using Bootmapper Client to change any keyboard settings, since not all the
-USB report options are supported.  
-
-Hardware Supported: JJ50 with the ATmega32a chip.  
-Hardware Availability: [KPrepublic on AliExpress](https://www.aliexpress.com/item/jj50-v1-0-Custom-Mechanical-Keyboard-50-PCB-programmed-50-preonic-layouts-bface-firmware-with-rgb/32848915277.html)
-
-This version by [Wayne K. Jones](github.com/WarmCatUK).
-
-
-## Installing and Building
+* Keyboard Maintainer: [Wayne K. Jones](github.com/WarmCatUK)
+* Hardware Supported: JJ50 with the ATmega32a chip.
+* Hardware Availability: [KPrepublic on AliExpress](https://www.aliexpress.com/item/jj50-v1-0-Custom-Mechanical-Keyboard-50-PCB-programmed-50-preonic-layouts-bface-firmware-with-rgb/32848915277.html)
 
 Make example for this keyboard (after setting up your build environment):
 
-```
-$ make jj50:default:program
-```
-It should detect the keyboard and set it to bootloader mode automatically, prior to flashing firmware.
-
-See [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) then the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information.
-
-Note that this is a complete replacement for the firmware, so you won't be
-using Bootmapper Client to change any keyboard settings, since not all the
-USB report options are supported.
-In addition you may need the AVR toolchain and `bootloadHID` for flashing:
-
-```
-$ brew cask install crosspack-avr
-$ brew install --HEAD https://raw.githubusercontent.com/robertgzr/homebrew-tap/master/bootloadhid.rb
-```
-
-In order to use the `././util/atmega32a_program.py` script, which can reboot the board into
-the bootloader, you'll need Python 2 with PyUSB installed:
-
-```
-$ pip install pyusb
-```
-
-If you prefer, you can just build it and flash the firmware directly with
-`bootloadHID` if you boot the board while holding down `Backspace` (`key below top right key`) to keep it
-in the bootloader:
-
-```
-$ make jj50
-$ bootloadHID -r jj50_default.hex
-```
-I dont use windows personally, but the following is from ymd96 regarding flashing the atmega32a:
-
-Since the JJ50 uses an ATmega32a chip instead of the 32u4, you need to download [HIDBootFlash v.1.0](http://vusb.wikidot.com/project:hidbootflash) for Windows. If anyone knows of a Linux/Mac bootflasher that works, edit this readme!
-On Windows, I use [MINGw](http://www.mingw.org/) to compile the keymaps. On Linux or OSX you can simply use the terminal.
-
-Once you have those two pieces of software:
-Build the keyboard with  
-```
-$ make jj50:default
-```  
-If you make your own layout, change the `default` word to whatever your layout is.  
-
-And flash the compiled hex file with `HIDBootFlash`. Simply put the board in flashing mode by plugging it in while holding the key below the top right key, and click `find device`. Then you can specify the .hex file and flash it to the device.
-
-
-## Troubleshooting
+    make jj50:default
 
-1. Try plugging the board in while pressing `Backspace` (`Key below the top right key`). This will force it to boot only the bootloader without loading the firmware. Once this is done, just reflash the board with the original firmware.
-2. Sometimes USB hubs can act weird, so try connecting the board directly to your computer or plugging/unplugging the USB hub.
-3. If you get an error such as "Resource Unavailable" when attemting to flash on Linux, you may want to compile and run `tools/usb_detach.c`. See `tools/README.md` for more info.
-4. I was occasionally finding that I wasn't flashing changes that I was making to my keymap. If that happens, remove the previous build and simply force rebuild by making with:
-```
-$ rm jj50_default.hex
-$ make -B jj50:default
-$ make -B jj50:default:program
-```
+Flashing example for this keyboard ([after setting up the bootloadHID flashing environment](https://docs.qmk.fm/#/flashing_bootloadhid))
 
+    make jj50:default:flash
 
+**Reset Key**: Hold down the key `Backspace` (`Key below the top right key`) while plugging in the keyboard.
 
+See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).