Merge remote-tracking branch 'upstream/master'

2 files changed, 37 insertions, 49 deletions

diff --git a/keyboards/snampad/info.json b/keyboards/snampad/info.json
index e69de29bb..2974eab86 100644
--- a/keyboards/snampad/info.json
+++ b/keyboards/snampad/info.json
@@ -0,0 +1,35 @@
+{
+    "keyboard_name": "snampad",
+    "url": "",
+    "maintainer": "ptillemans",
+    "width": 4,
+    "height": 6,
+    "layouts": {
+        "LAYOUT_numpad_6x4": {
+            "key_count": 21,
+            "layout": [
+                {"label":"Esc", "x":0, "y":0},
+                {"label":"Tab", "x":1, "y":0},
+                {"label":"Fn", "x":2, "y":0},
+                {"label":"Back", "x":3, "y":0},
+                {"label":"Num Lock", "x":0, "y":1},
+                {"label":"/", "x":1, "y":1},
+                {"label":"*", "x":2, "y":1},
+                {"label":"-", "x":3, "y":1},
+                {"label":"7", "x":0, "y":2},
+                {"label":"8", "x":1, "y":2},
+                {"label":"9", "x":2, "y":2},
+                {"label":"4", "x":0, "y":3},
+                {"label":"5", "x":1, "y":3},
+                {"label":"6", "x":2, "y":3},
+                {"label":"+", "x":3, "y":2, "h":2},
+                {"label":"1", "x":0, "y":4},
+                {"label":"2", "x":1, "y":4},
+                {"label":"3", "x":2, "y":4},
+                {"label":"0", "x":0, "y":5, "w":2},
+                {"label":".", "x":2, "y":5},
+                {"label":"Enter", "x":3, "y":4, "h":2}
+            ]
+        }
+    }
+}
diff --git a/keyboards/snampad/rules.mk b/keyboards/snampad/rules.mk
index ec3208fd0..1a1fbe6bc 100644
--- a/keyboards/snampad/rules.mk
+++ b/keyboards/snampad/rules.mk
@@ -1,63 +1,16 @@
 # MCU name
 MCU = atmega32u4
 
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
 # Bootloader selection
 #   Teensy       halfkay
 #   Pro Micro    caterina
 #   Atmel DFU    atmel-dfu
 #   LUFA DFU     lufa-dfu
 #   QMK DFU      qmk-dfu
-#   atmega32a    bootloadHID
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
 BOOTLOADER = caterina
 
-
-# If you don't know the bootloader type, then you can specify the
-# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
-#   Teensy halfKay      512
-#   Teensy++ halfKay    1024
-#   Atmel DFU loader    4096
-#   LUFA bootloader     4096
-#   USBaspLoader        2048
-# OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
-
 # Build Options
 #   change yes to no to disable
 #