UT47 layout (#2791)

* Add new project files for UT47

* Copy over keymap and related files

* Add LED_controls.ino

* Add README instructions

* Attempt sending press byte data

* Disable mousekeys

* Enable sending serial data to LED controller

* Update LED mode names

* Remove extra file

* Add LED enable flag

* Update READMEs with more info

* Credit original author

* Update copyrights

* Update docs

* Changed based on review

* Move layout screenshot to Imgur

* Append to src

* Enable mousekeys to fix bad keycodes

* Additional changes based on feedback

* Fix fn layer keys

1 files changed, 70 insertions, 0 deletions

diff --git a/keyboards/ut47/rules.mk b/keyboards/ut47/rules.mk
new file mode 100644
index 000000000..b04659866
--- /dev/null
+++ b/keyboards/ut47/rules.mk
@@ -0,0 +1,70 @@
+# MCU name
+#MCU = at90usb1286
+MCU = atmega32u4
+
+# Processor frequency.
+#     This will define a symbol, F_CPU, in all source code files equal to the
+#     processor frequency in Hz. You can then use this symbol in your source code to
+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#     automatically to create a 32-bit value in your source code.
+#
+#     This will be an integer division of F_USB below, as it is sourced by
+#     F_USB after it has run through any CPU prescalers. Note that this value
+#     does not *change* the processor frequency - it should merely be updated to
+#     reflect the processor speed set externally so that the code can use accurate
+#     software delays.
+F_CPU = 16000000
+
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+# Bootloader
+BOOTLOADER = caterina
+
+# custom matrix setup
+CUSTOM_MATRIX = yes
+SRC += matrix.c protocol/serial_uart.c
+
+# Build Options
+#   change yes to no to disable
+#
+BOOTMAGIC_ENABLE = yes      # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = yes       # Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
+CONSOLE_ENABLE = no        # Console for debug(+400)
+COMMAND_ENABLE = yes        # Commands for debug and configuration
+# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
+SLEEP_LED_ENABLE = no       # Breathing sleep LED during USB suspend
+# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+NKRO_ENABLE = yes            # USB Nkey Rollover
+BACKLIGHT_ENABLE = no       # Enable keyboard backlight functionality on B7 by default
+MIDI_ENABLE = no            # MIDI support (+2400 to 4200, depending on config)
+UNICODE_ENABLE = no         # Unicode
+BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
+AUDIO_ENABLE = no           # Audio output on port C6
+FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches
+
+ifeq ($(strip $(LED_ENABLE)), yes)
+  OPT_DEFS += -DLED_ENABLE
+  SRC += led.c
+endif