adding traveller keyboard

7 files changed, 697 insertions, 0 deletions

diff --git a/keyboards/handwired/traveller/Makefile b/keyboards/handwired/traveller/Makefile
new file mode 100644
index 000000000..12a4b71f4
--- /dev/null
+++ b/keyboards/handwired/traveller/Makefile
@@ -0,0 +1,89 @@
+
+#MCU = at90usb1287
+MCU = atmega32u4
+
+# Processor frequency.
+#     This will define a symbol, F_CPU, in all source code files equal to the
+#     processor frequency in Hz. You can then use this symbol in your source code to
+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#     automatically to create a 32-bit value in your source code.
+#
+#     This will be an integer division of F_USB below, as it is sourced by
+#     F_USB after it has run through any CPU prescalers. Note that this value
+#     does not *change* the processor frequency - it should merely be updated to
+#     reflect the processor speed set externally so that the code can use accurate
+#     software delays.
+F_CPU = 16000000
+
+# for avr upload
+USB ?= /dev/cu.usbmodem1421
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+
+ifdef TEENSY2
+    OPT_DEFS += -DATREUS_TEENSY2
+    ATREUS_UPLOAD_COMMAND = teensy_loader_cli -w -mmcu=$(MCU) $(TARGET).hex
+else
+    OPT_DEFS += -DATREUS_ASTAR
+    OPT_DEFS += -DCATERINA_BOOTLOADER
+    ATREUS_UPLOAD_COMMAND = while [ ! -r $(USB) ]; do sleep 1; done; \
+                            avrdude -p $(MCU) -c avr109 -U flash:w:$(TARGET).hex -P $(USB)
+endif
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+
+# MCU name
+
+# Boot Section Size in *bytes*
+#   Teensy halfKay   512
+#   Teensy++ halfKay 1024
+#   Atmel DFU loader 4096
+#   LUFA bootloader  4096
+#   USBaspLoader     2048
+OPT_DEFS += -DBOOTLOADER_SIZE=4096
+
+
+# Build Options
+#   change yes to no to disable
+#
+BOOTMAGIC_ENABLE ?= no      # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = yes       # Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
+CONSOLE_ENABLE ?= no        # Console for debug(+400)
+COMMAND_ENABLE ?= no        # Commands for debug and configuration
+# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
+SLEEP_LED_ENABLE ?= no       # Breathing sleep LED during USB suspend
+# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+NKRO_ENABLE ?= no            # USB Nkey Rollover
+BACKLIGHT_ENABLE ?= no       # Enable keyboard backlight functionality on B7 by default
+MIDI_ENABLE ?= no            # MIDI controls
+UNICODE_ENABLE ?= no         # Unicode
+BLUETOOTH_ENABLE ?= no       # Enable Bluetooth with the Adafruit EZ-Key HID
+AUDIO_ENABLE ?= no           # Audio output on port C6
+RGBLIGHT_ENABLE = yes
+
+ifndef QUANTUM_DIR
+	include ../../../Makefile
+endif
+
+upload: build
+	$(ATREUS_UPLOAD_COMMAND)
+
diff --git a/keyboards/handwired/traveller/config.h b/keyboards/handwired/traveller/config.h
new file mode 100644
index 000000000..2b82da447
--- /dev/null
+++ b/keyboards/handwired/traveller/config.h
@@ -0,0 +1,173 @@
+/*
+Copyright 2012 Jun Wako <wakojun@gmail.com>
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program.  If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#ifndef CONFIG_H
+#define CONFIG_H
+
+#include "config_common.h"
+
+/* USB Device descriptor parameter */
+#define VENDOR_ID       0xFEED
+#define PRODUCT_ID      0x6060
+#define DEVICE_VER      0x0001
+#define MANUFACTURER    You
+#define PRODUCT         traveller
+#define DESCRIPTION     A custom keyboard
+
+/* key matrix size */
+#define MATRIX_ROWS 4 
+#define MATRIX_COLS 13 
+
+/*
+ * Keyboard Matrix Assignments
+ *
+ * Change this to how you wired your keyboard
+ * COLS: AVR pins used for columns, left to right
+ * ROWS: AVR pins used for rows, top to bottom
+ * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode)
+ *                  ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode)
+ *
+*/
+#define MATRIX_ROW_PINS { D0, D1, D3, D2 }
+ // no I can't say why this order seemed like a good idea
+#define MATRIX_COL_PINS { B5, D6, B7, B6, F6, B1, B3, F7, B4, E6, D7, C6, D4 }
+#define UNUSED_PINS
+
+// LED stuff
+#define RGB_DI_PIN B2
+//#define RBLIGHT_TIMER
+#define RGBLED_NUM 1     // Number of LEDs
+#define RGBLIGHT_HUE_STEP 10
+#define RGBLIGHT_SAT_STEP 17
+#define RGBLIGHT_VAL_STEP 17
+
+
+/* COL2ROW or ROW2COL */
+#define DIODE_DIRECTION COL2ROW
+ 
+// #define BACKLIGHT_PIN B7
+// #define BACKLIGHT_BREATHING
+// #define BACKLIGHT_LEVELS 3
+
+
+/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */
+#define DEBOUNCING_DELAY 5
+
+/* define if matrix has ghost (lacks anti-ghosting diodes) */
+//#define MATRIX_HAS_GHOST
+
+/* number of backlight levels */
+#define BACKLIGHT_LEVELS 3
+
+/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
+//#define LOCKING_SUPPORT_ENABLE
+/* Locking resynchronize hack */
+#define LOCKING_RESYNC_ENABLE
+
+/*
+ * Force NKRO
+ *
+ * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved
+ * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the
+ * makefile for this to work.)
+ *
+ * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N)
+ * until the next keyboard reset.
+ *
+ * NKRO may prevent your keystrokes from being detected in the BIOS, but it is
+ * fully operational during normal computer usage.
+ *
+ * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N)
+ * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by
+ * bootmagic, NKRO mode will always be enabled until it is toggled again during a
+ * power-up.
+ *
+ */
+//#define FORCE_NKRO
+
+/*
+ * Magic Key Options
+ *
+ * Magic keys are hotkey commands that allow control over firmware functions of
+ * the keyboard. They are best used in combination with the HID Listen program,
+ * found here: https://www.pjrc.com/teensy/hid_listen.html
+ *
+ * The options below allow the magic key functionality to be changed. This is
+ * useful if your keyboard/keypad is missing keys and you want magic key support.
+ *
+ */
+
+/* key combination for magic key command */
+#define IS_COMMAND() ( \
+    keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \
+)
+
+/* control how magic key switches layers */
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS  true
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS  true
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM false
+
+/* override magic key keymap */
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM
+//#define MAGIC_KEY_HELP1          H
+//#define MAGIC_KEY_HELP2          SLASH
+//#define MAGIC_KEY_DEBUG          D
+//#define MAGIC_KEY_DEBUG_MATRIX   X
+//#define MAGIC_KEY_DEBUG_KBD      K
+//#define MAGIC_KEY_DEBUG_MOUSE    M
+//#define MAGIC_KEY_VERSION        V
+//#define MAGIC_KEY_STATUS         S
+//#define MAGIC_KEY_CONSOLE        C
+//#define MAGIC_KEY_LAYER0_ALT1    ESC
+//#define MAGIC_KEY_LAYER0_ALT2    GRAVE
+//#define MAGIC_KEY_LAYER0         0
+//#define MAGIC_KEY_LAYER1         1
+//#define MAGIC_KEY_LAYER2         2
+//#define MAGIC_KEY_LAYER3         3
+//#define MAGIC_KEY_LAYER4         4
+//#define MAGIC_KEY_LAYER5         5
+//#define MAGIC_KEY_LAYER6         6
+//#define MAGIC_KEY_LAYER7         7
+//#define MAGIC_KEY_LAYER8         8
+//#define MAGIC_KEY_LAYER9         9
+//#define MAGIC_KEY_BOOTLOADER     PAUSE
+//#define MAGIC_KEY_LOCK           CAPS
+//#define MAGIC_KEY_EEPROM         E
+//#define MAGIC_KEY_NKRO           N
+//#define MAGIC_KEY_SLEEP_LED      Z
+
+/*
+ * Feature disable options
+ *  These options are also useful to firmware size reduction.
+ */
+
+/* disable debug print */
+//#define NO_DEBUG
+
+/* disable print */
+//#define NO_PRINT
+
+/* disable action features */
+//#define NO_ACTION_LAYER
+//#define NO_ACTION_TAPPING
+//#define NO_ACTION_ONESHOT
+//#define NO_ACTION_MACRO
+//#define NO_ACTION_FUNCTION
+
+#endif
diff --git a/keyboards/handwired/traveller/keymaps/default/keymap.c b/keyboards/handwired/traveller/keymaps/default/keymap.c
new file mode 100644
index 000000000..13d889ab8
--- /dev/null
+++ b/keyboards/handwired/traveller/keymaps/default/keymap.c
@@ -0,0 +1,305 @@
+#include "traveller.h"
+#include "mousekey.h"
+#include "action_layer.h"
+
+// Each layer gets a name for readability, which is then used in the keymap matrix below.
+// The underscores don't mean anything - you can have a layer called STUFF or any other name.
+#define _QW 0
+#define _LW 1
+#define _HI 2
+#define _NAV 4
+#define _CUR 5
+#define _FKEYS 6 
+#define _TRNS 8
+
+// We do the same trick for functions
+#define  RGBLED_TOGGLE 10
+#define _HIOUT 15
+#define _LWOUT 16
+// Macros
+#define  MDL 4
+#define  MDR 5
+#define  MUR 6
+#define  MUL 3 
+
+
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+/* Qwerty
+ * ,-----------------------------------------.      .-----------------------------------------.
+ * | NAV  | ` ~  |   W  |   E  |   R  |   T  |      |  Y   |   U  |   I  |   O  |  -   |  =   |
+ * |------+------+------+------+------+------|      |------+------+------+------+------+------|
+ * | Tab  |   Q  |   S  |   D  |   F  |   G  |      |  H   |  J   |   K  |   L  |   P  |  \   |
+ * |------+------+------+------+------+------|------+------+------+------+------+------+------|
+ *|ctrl/esc|  A  |   X  |   C  |   V  |   B  |Ctrl /|   N  |   M  |   ,  |   .  |   ;  |  '   |
+ * |------+------+------+------+------+------+  //  +------+------+------+------+------+------|
+ * | Shift|   Z  | Del  | GUI  | Low  | Bspc |/Enter| Spc  | Hi   | GUI  | Alt  |  /   |Shift |
+ * `------------------------------------------------------------------------------------------'
+ * 
+ */
+[_QW] = KEYMAP( 
+  F(_NAV),          KC_GRV, KC_W,    KC_E,    KC_R,    KC_T,             KC_Y,    KC_U,    KC_I,    KC_O,    KC_MINS,  KC_EQL,
+  KC_TAB,           KC_Q,    KC_S,    KC_D,    KC_F,    KC_G,            KC_H,    KC_J,    KC_K,    KC_L,    KC_P, 	KC_BSLS,
+  CTL_T(KC_ESC),    KC_A,    KC_X,    KC_C,    KC_V,    KC_B,    KC_RCTL,  KC_N,    KC_M,    KC_COMM, KC_DOT,  KC_SCLN, 	KC_QUOT,
+  KC_LSFT, KC_Z,    KC_DEL, KC_LGUI, MO(_LW), KC_BSPC, KC_ENTER, KC_SPC,  MO(_HI), KC_RGUI, KC_RALT,    KC_SLSH,   KC_RSFT
+ ),
+
+/* LOW  - numbers, missing or awkward programming keys
+ Doubled 1 key allows lazy reach with ring finger. 
+ * ,-----------------------------------------.      .-----------------------------------------.
+ * | FKeys|   1  |   2  |  3   |   4  |   5  |      |  6   |  7   |   8  |   9  |   0  |Ctrl-alt-del|
+ * |------+------+------+------+------+------|      +------+------+------+------+------+------|
+ * | Tab  |   1  |  ]   |  (   |  )   |      |      |   *  |   (  |   )  |   [  |      |      |
+ * |------+------+------+------+------+------|------+------+------+------+------+------+------|
+ * | Caps |  [   |      |  {   |   }  |  `   |     /|   #  |   {  |   }  |      | ]    |      |
+ * |------+------+------+------+------+------+  //  +------+------+------+------+------+------|
+ * | Shift|      |      |      | Low  |      |/     |      |  Hi  |      |      |      |Shift |
+ * `------------------------------------------------------------------------------------------'
+ * 
+ */
+
+[_LW] = KEYMAP( 
+  F(_FKEYS),   KC_1,     KC_2,      KC_3,     KC_4,    KC_5,             KC_6,    KC_7,       KC_8,      KC_9,    KC_0,  LCTL(LALT(KC_DEL)) ,
+  KC_TRNS,  KC_1,     KC_RBRC,   KC_LPRN,  KC_RPRN, KC_NO,               KC_ASTR, KC_LPRN,    KC_RPRN,    KC_LBRC,    KC_NO, KC_NO,
+  KC_CAPS,   KC_LBRC,  KC_NO,     KC_LCBR,  KC_RCBR, KC_TILD,   KC_TRNS,  KC_HASH, KC_LCBR,    KC_RCBR,   KC_NO,    KC_RBRC,   KC_NO,
+  KC_TRNS,  KC_TRNS,  KC_TRNS,   KC_TRNS,  KC_TRNS, KC_TRNS,  KC_TRNS,  KC_TRNS, KC_TRNS,    KC_TRNS,   KC_TRNS,  KC_TRNS,  KC_TRNS
+),
+
+/* HI - Punctuation, shell and 
+url ://@.com  row on bottom,    && is opposite ||       ^$ are in regex order: ^.*$    
+Right hand nav keys work pretty well chorded with the Right hand Hi Key
+ * ,-----------------------------------------.      .-----------------------------------------.
+ * |FKEYS |   !  |   @  |   #  |   $  |   %  |      |  ^   |   &  |   *  |   (  |   )  |   +  |
+ * |------+------+------+------+------+------|      |------+------+------+------+------+------|
+ * |      |  !   |  &   |  "|" |   $  |   %  |      |  Vol+|  Mute|      |      |      |      |
+ * |------+------+------+------+------+------|------+------+------+------+------+------+------|
+ * | CAPS |  ^   |   :  |   .  |   *  |   -  |     /|  Vol-| Play | PgUp | Home | Up   | End  |
+ * |------+------+------+------+------+------+  //  +------+------+------+------+------+------|
+ * |      |   /  |      |      | Low  |      |/     |      |  Hi  | PgDn | Left| Down | Right |
+ * `------------------------------------------------------------------------------------------'
+ * 
+ */
+
+[_HI] = KEYMAP( 
+ F(_FKEYS), KC_EXLM,  KC_AT,   KC_HASH,  KC_DLR,   KC_PERC,           KC_CIRC,  KC_AMPR,    KC_ASTR,   KC_LPRN,  KC_RPRN,  KC_PLUS,
+ KC_TRNS, KC_EXLM,  KC_AMPR, KC_PIPE,  KC_DLR,   KC_PERC,             KC_VOLU, KC_MUTE,    KC_NO,     KC_NO,    KC_NO,    KC_NO, 
+ KC_CAPS, KC_CIRC,  KC_COLN,  KC_DOT,  KC_ASTR,  KC_MINS,   KC_TRNS,  KC_VOLD, KC_PPLS,    KC_PGUP,   KC_HOME,  KC_UP,    KC_END,
+ KC_TRNS, KC_SLSH,  KC_TRNS,  KC_TRNS, F(_LW),   KC_TRNS,   KC_TRNS,  KC_TRNS, KC_TRNS,    KC_PGDN,   KC_LEFT,  KC_DOWN,  KC_RIGHT 
+),	
+
+/* NAV - mouse &  navigation
+//gui left and right are line home/end, or fore & back in browser
+// Mouse buttons are reversed for comfort - bigger stretch is to the right button. 
+
+ * ,-----------------------------------------.      .-----------------------------------------.
+* | NAV  |      |      | Up   |      |Gui-> |      | MwU  | MS_UL| MS_U |MS_UR |      |Ms Norm|
+* |------+------+------+------+------+------|      |------+------+------+------+------+--------|
+* |      |Gui<- | Left | Down |Right | C^E  |      | BTN3 | MS_L |MS Up | MS_R |      |Ms Fast |
+* |------+------+------+------+------+------|------|------+------+------+------+------+--------|
+* |      | C^A  | GUI X| GUI C| GUI_V|      |Enter/| MWD  | M_DL |MS Dwn|MS_DR | Up   |Ms Slow |
+* |------+------+------+------+------+------+  //  +------+------+------+------+------+------|
+* |      | GuiZ |      |      | Low  |      |/ButnR|ButnL |  Hi  |      | Left | Down | Right |
+* `------------------------------------------------------------------------------------------'
+*/
+
+[_NAV] = KEYMAP( 
+  F(_NAV),  KC_NO,         KC_NO,    KC_UP,       KC_NO,     RGUI(KC_RIGHT),            KC_WH_U,  M(MUL), KC_MS_U,   M(MUR), KC_NO, KC_ACL2,
+  KC_TRNS, RGUI(KC_LEFT),  KC_LEFT,  KC_DOWN,     KC_RIGHT,  LCTL(KC_E),                KC_BTN3,  KC_MS_L,  KC_MS_U,   KC_MS_R,  KC_NO, KC_ACL1,
+  KC_TRNS, LCTL(KC_A),     LGUI(KC_X),RGUI(KC_C), RGUI(KC_V),KC_NO,         KC_ENTER,   KC_WH_D,  M(MDL), KC_MS_D,  M(MDR),  KC_UP, KC_ACL0,
+  KC_TRNS, RGUI(KC_Z),     KC_TRNS,  KC_TRNS,     KC_TRNS,   KC_TRNS,       KC_BTN2,   KC_BTN1,  KC_TRNS,  KC_TRNS,   KC_LEFT,   KC_DOWN,   KC_RIGHT
+),
+
+/* FKEYS - Funtion keys & mac stuff
+ * ,-----------------------------------------.      .-----------------------------------------.
+ * | FKEYS| F1   | F2   | F3   |  F4  | F5   |      | F6   | F7   | F8   | F9   | F10  | Ctrl | 
+ * |------+------+------+------+------+------|      |------+------+------+------+------+------|
+ * |      |      |      |      |      |      |      |  F11 | F12  |  F13 | F14  |  F15 | Alt  |
+ * |------+------+------+------+------+------|------+------+------+------+------+------+------|
+ * |Qwerty|      |      |      |      |      |     /|      |      |      |      |      | Del  |
+ * |------+------+------+------+------+------+  //  +------+------+------+------+------+------|
+ * |    . |RGBTog|  .   |      | LO   | Bspc |/     |      | HI   |      |      |      |      |
+ * `------------------------------------------------------------------------------------------'
+ *
+ */ 
+ 
+[_FKEYS] = KEYMAP( 
+  F(_FKEYS), KC_F1,    KC_F2,  	KC_F3,      KC_F4,     KC_F5,               KC_F6,    KC_F7,    KC_F8,    KC_F9,    KC_F10,    KC_RCTL,
+  KC_TRNS,   KC_NO,    KC_NO,   KC_NO,      KC_NO,     KC_NO,               KC_F11,   KC_F12,   KC_F13,    KC_F14,  KC_F15,  	 KC_LALT ,
+  F(_QW),   KC_NO,     KC_NO,   KC_NO,      KC_NO,     KC_NO,    KC_TRNS,   KC_NO,    KC_NO,    KC_NO,      KC_NO,   KC_NO,    KC_DEL,
+  KC_TRNS, F(RGBLED_TOGGLE),    KC_TRNS,    KC_TRNS,   KC_TRNS,  KC_TRNS,   KC_TRNS,   KC_TRNS,  KC_TRNS,    KC_TRNS,    KC_TRNS,    KC_TRNS,   KC_TRNS
+),
+
+
+/* TRNS - skeleton for laters
+ * ,-----------------------------------------.      .-----------------------------------------.
+ * |   .  |   .  |   .  |   .  |   .  |   .  |      |  ^   |   &  |   *  |   (  |   )  |      |
+ * |------+------+------+------+------+------|      |------+------+------+------+------+------|
+ * |   .  |   .  |   .  |   .  |   .  |   .  |      |  6   |  7   |   8  |   9  |   0  |      |
+ * |------+------+------+------+------+------|------+------+------+------+------+------+------|
+ * |   .  |   .  |   .  |   .  |   .  |   .  |     /|      |      |      |   .  |   ;  |  "   |
+ * |------+------+------+------+------+------+  //  +------+------+------+------+------+------|
+ * |    . |   .  |  .   | GUI  |  LO  |   .  |/     | Spc  |  HI  | GUI  |  M0  |  /   |LSFT |
+ * `------------------------------------------------------------------------------------------'
+ * 
+ */
+
+[_TRNS] = {
+  {KC_TRNS,  KC_TRNS,   KC_TRNS,    KC_TRNS,    KC_TRNS,    KC_TRNS,   KC_NO,    KC_TRNS,    KC_TRNS,    KC_TRNS,    KC_TRNS,    KC_TRNS,   KC_TRNS},
+  {KC_TRNS,  KC_TRNS,   KC_TRNS,    KC_TRNS,    KC_TRNS,    KC_TRNS,   KC_NO,    KC_TRNS,    KC_TRNS,    KC_TRNS,    KC_TRNS,    KC_TRNS, 	KC_TRNS},
+  {KC_TRNS,  KC_TRNS,   KC_TRNS,    KC_TRNS,    KC_TRNS,    KC_TRNS,   KC_TRNS,  KC_TRNS,    KC_TRNS,    KC_TRNS,    KC_TRNS,    KC_TRNS, 	KC_TRNS},
+  {KC_TRNS, KC_TRNS,    KC_TRNS,    KC_TRNS,    KC_TRNS,    KC_TRNS,   KC_TRNS,  KC_TRNS,    KC_TRNS,    KC_TRNS,    KC_TRNS,    KC_TRNS,   KC_TRNS}
+ }
+
+
+};
+
+
+const uint16_t PROGMEM fn_actions[] = {
+    [_QW] = ACTION_LAYER_ON(_QW,ON_RELEASE), // return to QWERTY  layer
+    [_LW] = ACTION_LAYER_TAP_TOGGLE(_LW), // Turn on LW when holding, or tap 3 times to switch
+    [_HI] = ACTION_LAYER_TAP_TOGGLE(_HI), // Turn on LW when holding, or tap 3 times to switch               
+    [_NAV] = ACTION_LAYER_TOGGLE(_NAV),                                   
+    [_FKEYS] = ACTION_LAYER_TOGGLE(_FKEYS),  
+    [_LWOUT] = ACTION_LAYER_OFF(_LW,ON_RELEASE),
+    [_HIOUT] = ACTION_LAYER_OFF(_HI,ON_RELEASE),
+    
+    // Functions
+  [RGBLED_TOGGLE]  = ACTION_FUNCTION(RGBLED_TOGGLE),
+ 
+};
+
+const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt)
+{
+  // MACRODOWN only works in this function
+      switch(id) {
+        case 0:
+          if (record->event.pressed) {
+            register_code(KC_RSFT);
+            #ifdef BACKLIGHT_ENABLE
+              backlight_step();
+            #endif
+          } else {
+            unregister_code(KC_RSFT);
+          }
+        break;
+
+   // from  algernon's ErgoDox EZ layout,
+       case MUL:
+        if (record->event.pressed) {
+          mousekey_on(KC_MS_UP);
+          mousekey_on(KC_MS_LEFT);
+        } else {
+          mousekey_off(KC_MS_UP);
+          mousekey_off(KC_MS_LEFT);
+        }
+        mousekey_send();
+        break;
+
+      case MUR:
+        if (record->event.pressed) {
+          mousekey_on(KC_MS_UP);
+          mousekey_on(KC_MS_RIGHT);
+        } else {
+          mousekey_off(KC_MS_UP);
+          mousekey_off(KC_MS_RIGHT);
+        }
+        mousekey_send();
+        break;
+
+      case MDL:
+        if (record->event.pressed) {
+          mousekey_on(KC_MS_DOWN);
+          mousekey_on(KC_MS_LEFT);
+        } else {
+          mousekey_off(KC_MS_DOWN);
+          mousekey_off(KC_MS_LEFT);
+        }
+        mousekey_send();
+        break;
+
+      case MDR:
+        if (record->event.pressed) {
+          mousekey_on(KC_MS_DOWN);
+          mousekey_on(KC_MS_RIGHT);
+        } else {
+          mousekey_off(KC_MS_DOWN);
+          mousekey_off(KC_MS_RIGHT);
+        }
+        mousekey_send();
+        break;
+
+
+      }
+    return MACRO_NONE;
+};
+
+
+
+void action_function(keyrecord_t *record, uint8_t id, uint8_t opt) {
+  switch (id) {
+    case RGBLED_TOGGLE:
+      //led operations
+      if (record->event.pressed) {
+        rgblight_toggle();
+      }
+        break;
+  }
+}
+
+ 
+
+void LayerLEDSet(uint8_t layr) {
+
+    switch (layr) {
+        case _QW:
+            rgblight_setrgb(0,20, 0); //  dim green
+        break;
+        case _LW:
+            // deep purple
+            rgblight_setrgb(20,0,35); 
+            break;  
+        case _HI:
+            // light blue
+           rgblight_setrgb(0,20,20); 
+            break;    
+        case _NAV:
+            // Yellowy orange
+            rgblight_setrgb(25,20,0); // brighter
+            break;
+        case _FKEYS:
+         // RED
+           rgblight_setrgb(20,0,0); // brighter
+            break;  
+        default:
+            rgblight_setrgb(20,2,20);//error
+            break;
+    }
+ 
+ return;
+  
+}
+
+void matrix_init_user(void) {
+}
+
+// Bleah globals need to be initialized.
+uint8_t old_layer=_QW;
+
+void matrix_scan_user(void) {
+         uint8_t layer = biton32(layer_state);
+         if (old_layer != layer) {
+           LayerLEDSet(layer);
+           old_layer=layer;
+           }
+}
+
+
+bool process_record_user(uint16_t keycode, keyrecord_t *record) {
+  return true;
+}
+
+void led_set_user(uint8_t usb_led) {
+
+}
+
+
diff --git a/keyboards/handwired/traveller/keymaps/default/readme.md b/keyboards/handwired/traveller/keymaps/default/readme.md
new file mode 100644
index 000000000..7ddc40b3c
--- /dev/null
+++ b/keyboards/handwired/traveller/keymaps/default/readme.md
@@ -0,0 +1,2 @@
+# The default keymap for handwired/traveller
+this is a kitchen sink build 
diff --git a/keyboards/handwired/traveller/readme.md b/keyboards/handwired/traveller/readme.md
new file mode 100644
index 000000000..646844b1d
--- /dev/null
+++ b/keyboards/handwired/traveller/readme.md
@@ -0,0 +1,35 @@
+traveler keyboard firmware
+======================
+
+## Traveller Specific Info ##
+The traveller is a varient on the atreus keyboard. 
+Like the Atreus, it is designed to be a good compromise between size and ergonomics. 
+
+key differences are 
+- an additional column for each pinky
+- an RGB LED in the center to show the current layer
+- more finger stagger,  splay angle and contoured keycaps (F2 profile for space key). 
+
+You can make your own traveller  keyboard by using the openscad tools from the atreus repository, and adding a hole for the LED to shine through. 
+
+## Quantum MK Firmware
+
+For the full Quantum feature list, see [the parent README.md](/README.md).
+
+## Building
+
+Download or clone the whole firmware and navigate to the keyboard/traveler folder. Once your dev env is setup, you'll be able to type `make` to generate your .hex - you can then use the Teensy Loader to program your .hex file. 
+
+Depending on which keymap you would like to use, you will have to compile slightly differently.
+
+### Default
+To build with the default keymap, simply run `make`.
+
+### Other Keymaps
+Several version of keymap are available in advance but you are recommended to define your favorite layout yourself. To define your own keymap create file named `<name>.c` and see keymap document (you can find in top README.md) and existent keymap files.
+
+To build the firmware binary hex file with a keymap just do `make` with `KEYMAP` option like:
+```
+$ make KEYMAP=[default|jack|<name>]
+```
+Keymaps follow the format **__\<name\>.c__** and are stored in the `keymaps` folder.
diff --git a/keyboards/handwired/traveller/traveller.c b/keyboards/handwired/traveller/traveller.c
new file mode 100644
index 000000000..9d2534130
--- /dev/null
+++ b/keyboards/handwired/traveller/traveller.c
@@ -0,0 +1,61 @@
+#include "traveller.h"
+
+__attribute__ ((weak))
+void matrix_init_user(void) {
+        // leave this function blank - it can be defined in a keymap file
+};
+
+__attribute__ ((weak))
+void matrix_scan_user(void) {
+        // leave this function blank - it can be defined in a keymap file
+}
+
+__attribute__ ((weak))
+void process_action_user(keyrecord_t *record) {
+        // leave this function blank - it can be defined in a keymap file
+}
+
+__attribute__ ((weak))
+void led_set_user(uint8_t usb_led) {
+        // leave this function blank - it can be defined in a keymap file
+}
+
+void matrix_init_kb(void) {
+        // put your keyboard start-up code here
+        // runs once when the firmware starts up
+
+#ifdef RGBLIGHT_ENABLE
+        rgblight_init();
+        rgblight_mode(1); // solid, no timer
+        rgblight_setrgb(0,20,0);// dim green, happens to be same as _QW
+#endif
+
+// Turn status LED on
+        DDRC |= (1<<7);
+        PORTC |= (1<<7);
+
+        matrix_init_user();
+}
+
+
+void matrix_scan_kb(void) {
+	// put your looping keyboard code here
+	// runs every cycle (a lot)
+
+	matrix_scan_user();
+}
+
+bool process_record_kb(uint16_t keycode, keyrecord_t *record) {
+	// put your per-action keyboard code here
+	// runs for every action, just before processing by the firmware
+
+	return process_record_user(keycode, record);
+}
+
+void led_set_kb(uint8_t usb_led) {
+	// put your keyboard LED indicator (ex: Caps Lock LED) toggling code here
+
+	led_set_user(usb_led);
+}
+
+
diff --git a/keyboards/handwired/traveller/traveller.h b/keyboards/handwired/traveller/traveller.h
new file mode 100644
index 000000000..972a1a94a
--- /dev/null
+++ b/keyboards/handwired/traveller/traveller.h
@@ -0,0 +1,32 @@
+#ifndef TRAVELLER_H
+#define TRAVELLER_H
+
+#include "quantum.h"
+#include "led.h"
+
+#ifdef RGBLIGHT_ENABLE
+  #include "rgblight.h"
+#endif
+#ifdef BACKLIGHT_ENABLE
+        #include "backlight.h"
+#endif
+
+
+
+// This a shortcut to help you visually see your layout.
+// The first section contains all of the arguements
+// The second converts the arguments into a two-dimensional array
+#define KEYMAP( \
+        k00, k01, k02, k03, k04, k05,       k07, k08, k09, k0a, k0b, k0c, \
+        k10, k11, k12, k13, k14, k15,       k17, k18, k19, k1a, k1b, k1c, \
+        k20, k21, k22, k23, k24, k25, k26, k27, k28, k29, k2a, k2b, k2c, \
+        k30, k31, k32, k33, k34, k35, k36, k37, k38, k39, k3a, k3b, k3c  \
+) \
+{ \
+        { k00, k01, k02, k03, k04, k05, KC_NO, k07, k08, k09, k0a, k0b, k0c }, \
+        { k10, k11, k12, k13, k14, k15, KC_NO, k17, k18, k19, k1a, k1b, k1c }, \
+        { k20, k21, k22, k23, k24, k25, k26,   k27, k28, k29, k2a, k2b, k2c }, \
+        { k30, k31, k32, k33, k34, k35, k36,   k37, k38, k39, k3a, k3b, k3c } \
+}
+
+#endif