diff options
| author |  Fred Sundvik <fsundvik@gmail.com> | 2016-08-07 17:04:39 +0300 |
|---|---|---|
| committer | Fred Sundvik <fsundvik@gmail.com> | 2016-08-20 03:56:08 +0300 |
| commit | 44441de8cad7255fd0637459ed39b89e34751b78 (patch) | |
| tree | 89056dc6ea70b3367fb1fa0ca408975909b5a20a /keyboards | |
| parent | 0d5caead5ad0edc06aedda06814da05815fc177e (diff) | |
| download | qmk_firmware-44441de8cad7255fd0637459ed39b89e34751b78.tar.gz | |
Split keyboard makefiles into rules and Makefile
Diffstat (limited to 'keyboards')
55 files changed, 1791 insertions, 1902 deletions
diff --git a/keyboards/alps64/Makefile b/keyboards/alps64/Makefile index d8325e6c8..4e2a6f00f 100644 --- a/keyboards/alps64/Makefile +++ b/keyboards/alps64/Makefile @@ -1,70 +1,3 @@ - - -# Target file name (without extension). - -# project specific files -SRC = led.c - -# MCU name -MCU = atmega32u2 - -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=4096 - - -# Build Options -# comment out to disable the options. -# -BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000) -MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) -EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) -CONSOLE_ENABLE ?= yes # Console for debug(+400) -COMMAND_ENABLE ?= yes # Commands for debug and configuration -#SLEEP_LED_ENABLE = yes # Breathing sleep LED during USB suspend -#NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA - -ifndef QUANTUM_DIR +ifndef MAKEFILE_INCLUDED include ../../Makefile endif
\ No newline at end of file diff --git a/keyboards/alps64/rules.mk b/keyboards/alps64/rules.mk new file mode 100644 index 000000000..c326d3e26 --- /dev/null +++ b/keyboards/alps64/rules.mk @@ -0,0 +1,66 @@ + + +# Target file name (without extension). + +# project specific files +SRC = led.c + +# MCU name +MCU = atmega32u2 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + +# Boot Section Size in *bytes* +# Teensy halfKay 512 +# Teensy++ halfKay 1024 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +# USBaspLoader 2048 +OPT_DEFS += -DBOOTLOADER_SIZE=4096 + + +# Build Options +# comment out to disable the options. +# +BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) +EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) +CONSOLE_ENABLE ?= yes # Console for debug(+400) +COMMAND_ENABLE ?= yes # Commands for debug and configuration +#SLEEP_LED_ENABLE = yes # Breathing sleep LED during USB suspend +#NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA
\ No newline at end of file diff --git a/keyboards/amj60/Makefile b/keyboards/amj60/Makefile index 1f695aa4d..4e2a6f00f 100644 --- a/keyboards/amj60/Makefile +++ b/keyboards/amj60/Makefile @@ -1,70 +1,3 @@ - -# MCU name -#MCU = at90usb1287 -MCU = atmega32u4 - -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=4096 - - -# Build Options -# comment out to disable the options. -# -BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000) -MOUSEKEY_ENABLE ?= no # Mouse keys(+4700) -EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) -CONSOLE_ENABLE ?= yes # Console for debug(+400) -COMMAND_ENABLE ?= yes # Commands for debug and configuration -NKRO_ENABLE ?= yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work -RGBLIGHT_ENABLE ?= yes # Enable keyboard underlight functionality (+4870) -BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality (+1150) -MIDI_ENABLE ?= no # MIDI controls -AUDIO_ENABLE ?= no -UNICODE_ENABLE ?= no # Unicode -BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID - -ifndef QUANTUM_DIR +ifndef MAKEFILE_INCLUDED include ../../Makefile -endif +endif
\ No newline at end of file diff --git a/keyboards/amj60/rules.mk b/keyboards/amj60/rules.mk new file mode 100644 index 000000000..18403ac32 --- /dev/null +++ b/keyboards/amj60/rules.mk @@ -0,0 +1,66 @@ + +# MCU name +#MCU = at90usb1287 +MCU = atmega32u4 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + +# Boot Section Size in *bytes* +# Teensy halfKay 512 +# Teensy++ halfKay 1024 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +# USBaspLoader 2048 +OPT_DEFS += -DBOOTLOADER_SIZE=4096 + + +# Build Options +# comment out to disable the options. +# +BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE ?= no # Mouse keys(+4700) +EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) +CONSOLE_ENABLE ?= yes # Console for debug(+400) +COMMAND_ENABLE ?= yes # Commands for debug and configuration +NKRO_ENABLE ?= yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +RGBLIGHT_ENABLE ?= yes # Enable keyboard underlight functionality (+4870) +BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality (+1150) +MIDI_ENABLE ?= no # MIDI controls +AUDIO_ENABLE ?= no +UNICODE_ENABLE ?= no # Unicode +BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID diff --git a/keyboards/arrow_pad/Makefile b/keyboards/arrow_pad/Makefile index 09fcf3e7a..4e2a6f00f 100644 --- a/keyboards/arrow_pad/Makefile +++ b/keyboards/arrow_pad/Makefile @@ -1,74 +1,3 @@ - - -# MCU name -#MCU = at90usb1287 -MCU = atmega32u4 - -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=512 - - -# Build Options -# change yes to no to disable -# -BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000) -MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) -EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) -CONSOLE_ENABLE ?= yes # Console for debug(+400) -COMMAND_ENABLE ?= yes # Commands for debug and configuration -KEYBOARD_LOCK_ENABLE ?= yes # Allow locking of keyboard via magic key -# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE -SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend -# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work -NKRO_ENABLE ?= yes # USB Nkey Rollover -BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality -MIDI_ENABLE ?= no # MIDI controls -UNICODE_ENABLE ?= no # Unicode -BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID -AUDIO_ENABLE ?= no # Audio output on port C6 - -ifndef QUANTUM_DIR +ifndef MAKEFILE_INCLUDED include ../../Makefile endif
\ No newline at end of file diff --git a/keyboards/arrow_pad/rules.mk b/keyboards/arrow_pad/rules.mk new file mode 100644 index 000000000..3dca9b6ea --- /dev/null +++ b/keyboards/arrow_pad/rules.mk @@ -0,0 +1,70 @@ + + +# MCU name +#MCU = at90usb1287 +MCU = atmega32u4 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + +# Boot Section Size in *bytes* +# Teensy halfKay 512 +# Teensy++ halfKay 1024 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +# USBaspLoader 2048 +OPT_DEFS += -DBOOTLOADER_SIZE=512 + + +# Build Options +# change yes to no to disable +# +BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) +EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) +CONSOLE_ENABLE ?= yes # Console for debug(+400) +COMMAND_ENABLE ?= yes # Commands for debug and configuration +KEYBOARD_LOCK_ENABLE ?= yes # Allow locking of keyboard via magic key +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend +# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +NKRO_ENABLE ?= yes # USB Nkey Rollover +BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality +MIDI_ENABLE ?= no # MIDI controls +UNICODE_ENABLE ?= no # Unicode +BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID +AUDIO_ENABLE ?= no # Audio output on port C6
\ No newline at end of file diff --git a/keyboards/atomic/Makefile b/keyboards/atomic/Makefile index 08e9205cb..4e2a6f00f 100644 --- a/keyboards/atomic/Makefile +++ b/keyboards/atomic/Makefile @@ -1,73 +1,3 @@ - - -# MCU name -#MCU = at90usb1287 -MCU = atmega32u4 - -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=4096 - -# Build Options -# change to "no" to disable the options, or define them in the Makefile in -# the appropriate keymap folder that will get included automatically -# -BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000) -MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) -EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) -CONSOLE_ENABLE ?= no # Console for debug(+400) -COMMAND_ENABLE ?= yes # Commands for debug and configuration -NKRO_ENABLE ?= no # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work -BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality -MIDI_ENABLE ?= no # MIDI controls -AUDIO_ENABLE ?= no # Audio output on port C6 -UNICODE_ENABLE ?= no # Unicode -BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID -RGBLIGHT_ENABLE ?= no # Enable WS2812 RGB underlight. Do not enable this with audio at the same time. - -# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE -SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend - -ifndef QUANTUM_DIR +ifndef MAKEFILE_INCLUDED include ../../Makefile endif
\ No newline at end of file diff --git a/keyboards/atomic/rules.mk b/keyboards/atomic/rules.mk new file mode 100644 index 000000000..d0f3a3a1c --- /dev/null +++ b/keyboards/atomic/rules.mk @@ -0,0 +1,69 @@ + + +# MCU name +#MCU = at90usb1287 +MCU = atmega32u4 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + +# Boot Section Size in *bytes* +# Teensy halfKay 512 +# Teensy++ halfKay 1024 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +# USBaspLoader 2048 +OPT_DEFS += -DBOOTLOADER_SIZE=4096 + +# Build Options +# change to "no" to disable the options, or define them in the Makefile in +# the appropriate keymap folder that will get included automatically +# +BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) +EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) +CONSOLE_ENABLE ?= no # Console for debug(+400) +COMMAND_ENABLE ?= yes # Commands for debug and configuration +NKRO_ENABLE ?= no # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality +MIDI_ENABLE ?= no # MIDI controls +AUDIO_ENABLE ?= no # Audio output on port C6 +UNICODE_ENABLE ?= no # Unicode +BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID +RGBLIGHT_ENABLE ?= no # Enable WS2812 RGB underlight. Do not enable this with audio at the same time. + +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend
\ No newline at end of file diff --git a/keyboards/atreus/Makefile b/keyboards/atreus/Makefile index 5894d231f..4e2a6f00f 100644 --- a/keyboards/atreus/Makefile +++ b/keyboards/atreus/Makefile @@ -1,88 +1,3 @@ - - -ifdef TEENSY2 - OPT_DEFS += -DATREUS_TEENSY2 - ATREUS_UPLOAD_COMMAND = teensy_loader_cli -w -mmcu=$(MCU) $(TARGET).hex -else - OPT_DEFS += -DATREUS_ASTAR - OPT_DEFS += -DCATERINA_BOOTLOADER - ATREUS_UPLOAD_COMMAND = while [ ! -r $(USB) ]; do sleep 1; done; \ - avrdude -p $(MCU) -c avr109 -U flash:w:$(TARGET).hex -P $(USB) -endif - -# MCU name -#MCU = at90usb1287 -MCU = atmega32u4 - -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=4096 - - -# Build Options -# comment out to disable the options. -# -#BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000) -MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) -EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) -CONSOLE_ENABLE ?= yes # Console for debug(+400) -COMMAND_ENABLE ?= yes # Commands for debug and configuration -# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE -# SLEEP_LED_ENABLE ?= yes # Breathing sleep LED during USB suspend -NKRO_ENABLE ?= yes # USB Nkey Rollover - not yet supported in LUFA -# BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality -# MIDI_ENABLE ?= YES # MIDI controls -UNICODE_ENABLE ?= YES # Unicode -# BLUETOOTH_ENABLE ?= yes # Enable Bluetooth with the Adafruit EZ-Key HID - - -ifndef QUANTUM_DIR +ifndef MAKEFILE_INCLUDED include ../../Makefile -endif - -USB ?= /dev/cu.usbmodem1411 - -upload: build - $(ATREUS_UPLOAD_COMMAND) - +endif
\ No newline at end of file diff --git a/keyboards/atreus/rules.mk b/keyboards/atreus/rules.mk new file mode 100644 index 000000000..d71f50bb2 --- /dev/null +++ b/keyboards/atreus/rules.mk @@ -0,0 +1,82 @@ + + +ifdef TEENSY2 + OPT_DEFS += -DATREUS_TEENSY2 + ATRUES_UPLOAD_COMMAND = teensy_loader_cli -w -mmcu=$(MCU) $(TARGET).hex +else + OPT_DEFS += -DATREUS_ASTAR + OPT_DEFS += -DCATERINA_BOOTLOADER + ATRUES_UPLOAD_COMMAND = while [ ! -r $(USB) ]; do sleep 1; done; \ + avrdude -p $(MCU) -c avr109 -U flash:w:$(TARGET).hex -P $(USB) +endif + +# MCU name +#MCU = at90usb1287 +MCU = atmega32u4 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + +# Boot Section Size in *bytes* +# Teensy halfKay 512 +# Teensy++ halfKay 1024 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +# USBaspLoader 2048 +OPT_DEFS += -DBOOTLOADER_SIZE=4096 + + +# Build Options +# comment out to disable the options. +# +#BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) +EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) +CONSOLE_ENABLE ?= yes # Console for debug(+400) +COMMAND_ENABLE ?= yes # Commands for debug and configuration +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +# SLEEP_LED_ENABLE ?= yes # Breathing sleep LED during USB suspend +NKRO_ENABLE ?= yes # USB Nkey Rollover - not yet supported in LUFA +# BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality +# MIDI_ENABLE ?= YES # MIDI controls +UNICODE_ENABLE ?= YES # Unicode +# BLUETOOTH_ENABLE ?= yes # Enable Bluetooth with the Adafruit EZ-Key HID + +USB ?= /dev/cu.usbmodem1411 + +upload: build + $(ATRUES_UPLOAD_COMMAND)
\ No newline at end of file diff --git a/keyboards/bantam44/Makefile b/keyboards/bantam44/Makefile index 03893dbf8..4e2a6f00f 100644 --- a/keyboards/bantam44/Makefile +++ b/keyboards/bantam44/Makefile @@ -1,72 +1,3 @@ - - -# MCU name -#MCU = at90usb1287 -MCU = atmega32u4 - -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=512 - - -# Build Options -# comment out to disable the options. -# -BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000) -MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) -EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) -CONSOLE_ENABLE ?= yes # Console for debug(+400) -COMMAND_ENABLE ?= yes # Commands for debug and configuration -# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE -# SLEEP_LED_ENABLE ?= yes # Breathing sleep LED during USB suspend -# NKRO_ENABLE ?= yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work -# BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality -# MIDI_ENABLE ?= YES # MIDI controls -# UNICODE_ENABLE ?= YES # Unicode -# BLUETOOTH_ENABLE ?= yes # Enable Bluetooth with the Adafruit EZ-Key HID - -ifndef QUANTUM_DIR +ifndef MAKEFILE_INCLUDED include ../../Makefile -endif - +endif
\ No newline at end of file diff --git a/keyboards/bantam44/rules.mk b/keyboards/bantam44/rules.mk new file mode 100644 index 000000000..baa0e9e7a --- /dev/null +++ b/keyboards/bantam44/rules.mk @@ -0,0 +1,67 @@ + + +# MCU name +#MCU = at90usb1287 +MCU = atmega32u4 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + +# Boot Section Size in *bytes* +# Teensy halfKay 512 +# Teensy++ halfKay 1024 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +# USBaspLoader 2048 +OPT_DEFS += -DBOOTLOADER_SIZE=512 + + +# Build Options +# comment out to disable the options. +# +BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) +EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) +CONSOLE_ENABLE ?= yes # Console for debug(+400) +COMMAND_ENABLE ?= yes # Commands for debug and configuration +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +# SLEEP_LED_ENABLE ?= yes # Breathing sleep LED during USB suspend +# NKRO_ENABLE ?= yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +# BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality +# MIDI_ENABLE ?= YES # MIDI controls +# UNICODE_ENABLE ?= YES # Unicode +# BLUETOOTH_ENABLE ?= yes # Enable Bluetooth with the Adafruit EZ-Key HID diff --git a/keyboards/chibios_test/Makefile b/keyboards/chibios_test/Makefile index d9f2b8b83..4b07a6234 100644 --- a/keyboards/chibios_test/Makefile +++ b/keyboards/chibios_test/Makefile @@ -1,14 +1,5 @@ SUBPROJECT_DEFAULT = stm32_f072_onekey -#BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration -MOUSEKEY_ENABLE ?= yes # Mouse keys -EXTRAKEY_ENABLE ?= yes # Audio control and System control -CONSOLE_ENABLE ?= yes # Console for debug -COMMAND_ENABLE ?= yes # Commands for debug and configuration -SLEEP_LED_ENABLE ?= yes # Breathing sleep LED during USB suspend -NKRO_ENABLE ?= yes # USB Nkey Rollover -CUSTOM_MATRIX ?= yes # Custom matrix file - -ifndef QUANTUM_DIR +ifndef MAKEFILE_INCLUDED include ../../Makefile endif
\ No newline at end of file diff --git a/keyboards/chibios_test/rules.mk b/keyboards/chibios_test/rules.mk new file mode 100644 index 000000000..4b5a84535 --- /dev/null +++ b/keyboards/chibios_test/rules.mk @@ -0,0 +1,8 @@ +#BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration +MOUSEKEY_ENABLE ?= yes # Mouse keys +EXTRAKEY_ENABLE ?= yes # Audio control and System control +CONSOLE_ENABLE ?= yes # Console for debug +COMMAND_ENABLE ?= yes # Commands for debug and configuration +SLEEP_LED_ENABLE ?= yes # Breathing sleep LED during USB suspend +NKRO_ENABLE ?= yes # USB Nkey Rollover +CUSTOM_MATRIX ?= yes # Custom matrix file
\ No newline at end of file diff --git a/keyboards/clueboard/Makefile b/keyboards/clueboard/Makefile index e6b13f955..b9bada8f8 100644 --- a/keyboards/clueboard/Makefile +++ b/keyboards/clueboard/Makefile @@ -1,109 +1,5 @@ -#---------------------------------------------------------------------------- -# On command line: -# -# make all = Make software. -# -# make clean = Clean out built project files. -# -# make coff = Convert ELF to AVR COFF. -# -# make extcoff = Convert ELF to AVR Extended COFF. -# -# make program = Download the hex file to the device. -# Please customize your programmer settings(PROGRAM_CMD) -# -# make teensy = Download the hex file to the device, using teensy_loader_cli. -# (must have teensy_loader_cli installed). -# -# make dfu = Download the hex file to the device, using dfu-programmer (must -# have dfu-programmer installed). -# -# make flip = Download the hex file to the device, using Atmel FLIP (must -# have Atmel FLIP installed). -# -# make dfu-ee = Download the eeprom file to the device, using dfu-programmer -# (must have dfu-programmer installed). -# -# make flip-ee = Download the eeprom file to the device, using Atmel FLIP -# (must have Atmel FLIP installed). -# -# make debug = Start either simulavr or avarice as specified for debugging, -# with avr-gdb or avr-insight as the front end for debugging. -# -# make filename.s = Just compile filename.c into the assembler code only. -# -# make filename.i = Create a preprocessed source file for use in submitting -# bug reports to the GCC project. -# -# To rebuild project do "make clean" then "make all". -#---------------------------------------------------------------------------- - SUBPROJECT_DEFAULT = rev2 -# MCU name -MCU = atmega32u4 - -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=4096 - - -# Build Options -# change to no to disable the options. -# -BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000) -MOUSEKEY_ENABLE ?= no # Mouse keys(+4700) -EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) -CONSOLE_ENABLE ?= yes # Console for debug(+400) -COMMAND_ENABLE ?= yes # Commands for debug and configuration -NKRO_ENABLE ?= yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work -AUDIO_ENABLE ?= no -RGBLIGHT_ENABLE ?= no # Enable keyboard underlight functionality -MIDI_ENABLE ?= no # MIDI controls -UNICODE_ENABLE ?= no # Unicode -BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID - -ifndef QUANTUM_DIR +ifndef MAKEFILE_INCLUDED include ../../Makefile -endif +endif
\ No newline at end of file diff --git a/keyboards/clueboard/rules.mk b/keyboards/clueboard/rules.mk new file mode 100644 index 000000000..3909fbd5c --- /dev/null +++ b/keyboards/clueboard/rules.mk @@ -0,0 +1,103 @@ +#---------------------------------------------------------------------------- +# On command line: +# +# make all = Make software. +# +# make clean = Clean out built project files. +# +# make coff = Convert ELF to AVR COFF. +# +# make extcoff = Convert ELF to AVR Extended COFF. +# +# make program = Download the hex file to the device. +# Please customize your programmer settings(PROGRAM_CMD) +# +# make teensy = Download the hex file to the device, using teensy_loader_cli. +# (must have teensy_loader_cli installed). +# +# make dfu = Download the hex file to the device, using dfu-programmer (must +# have dfu-programmer installed). +# +# make flip = Download the hex file to the device, using Atmel FLIP (must +# have Atmel FLIP installed). +# +# make dfu-ee = Download the eeprom file to the device, using dfu-programmer +# (must have dfu-programmer installed). +# +# make flip-ee = Download the eeprom file to the device, using Atmel FLIP +# (must have Atmel FLIP installed). +# +# make debug = Start either simulavr or avarice as specified for debugging, +# with avr-gdb or avr-insight as the front end for debugging. +# +# make filename.s = Just compile filename.c into the assembler code only. +# +# make filename.i = Create a preprocessed source file for use in submitting +# bug reports to the GCC project. +# +# To rebuild project do "make clean" then "make all". +#---------------------------------------------------------------------------- + +# MCU name +MCU = atmega32u4 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + +# Boot Section Size in *bytes* +# Teensy halfKay 512 +# Teensy++ halfKay 1024 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +# USBaspLoader 2048 +OPT_DEFS += -DBOOTLOADER_SIZE=4096 + + +# Build Options +# comment out to disable the options. +# +BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE ?= no # Mouse keys(+4700) +EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) +CONSOLE_ENABLE ?= yes # Console for debug(+400) +COMMAND_ENABLE ?= yes # Commands for debug and configuration +NKRO_ENABLE ?= yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +AUDIO_ENABLE ?= no +RGBLIGHT_ENABLE ?= no # Enable keyboard underlight functionality +MIDI_ENABLE ?= no # MIDI controls +UNICODE_ENABLE ?= no # Unicode +BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID
\ No newline at end of file diff --git a/keyboards/cluecard/Makefile b/keyboards/cluecard/Makefile index 029d0b967..4e2a6f00f 100644 --- a/keyboards/cluecard/Makefile +++ b/keyboards/cluecard/Makefile @@ -1,76 +1,3 @@ - - -# MCU name -#MCU = at90usb1287 -MCU = atmega32u4 - -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=4096 - - -# Build Options -# change yes to no to disable -# -BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000) -MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) -EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) -CONSOLE_ENABLE ?= yes # Console for debug(+400) -COMMAND_ENABLE ?= yes # Commands for debug and configuration -# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE -SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend -# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work -NKRO_ENABLE ?= no # USB Nkey Rollover -RGBLIGHT_ENABLE ?= yes # Enable keyboard underlight functionality (+4870) -BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality by default -MIDI_ENABLE ?= no # MIDI controls -UNICODE_ENABLE ?= no # Unicode -BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID -AUDIO_ENABLE ?= yes # Audio output on port C6 - -ifndef QUANTUM_DIR +ifndef MAKEFILE_INCLUDED include ../../Makefile -endif - - +endif
\ No newline at end of file diff --git a/keyboards/cluecard/rules.mk b/keyboards/cluecard/rules.mk new file mode 100644 index 000000000..454235877 --- /dev/null +++ b/keyboards/cluecard/rules.mk @@ -0,0 +1,70 @@ + + +# MCU name +#MCU = at90usb1287 +MCU = atmega32u4 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + +# Boot Section Size in *bytes* +# Teensy halfKay 512 +# Teensy++ halfKay 1024 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +# USBaspLoader 2048 +OPT_DEFS += -DBOOTLOADER_SIZE=4096 + + +# Build Options +# change yes to no to disable +# +BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) +EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) +CONSOLE_ENABLE ?= yes # Console for debug(+400) +COMMAND_ENABLE ?= yes # Commands for debug and configuration +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend +# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +NKRO_ENABLE ?= no # USB Nkey Rollover +RGBLIGHT_ENABLE ?= yes # Enable keyboard underlight functionality (+4870) +BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality by default +MIDI_ENABLE ?= no # MIDI controls +UNICODE_ENABLE ?= no # Unicode +BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID +AUDIO_ENABLE ?= yes # Audio output on port C6 diff --git a/keyboards/cluepad/Makefile b/keyboards/cluepad/Makefile index a331ff4dc..4e2a6f00f 100644 --- a/keyboards/cluepad/Makefile +++ b/keyboards/cluepad/Makefile @@ -1,70 +1,3 @@ - -# MCU name -#MCU = at90usb1287 -MCU = atmega32u4 - -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=4096 - - -# Build Options -# comment out to disable the options. -# -BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000) -# MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) -# EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) -# CONSOLE_ENABLE ?= yes # Console for debug(+400) -# COMMAND_ENABLE ?= yes # Commands for debug and configuration -NKRO_ENABLE ?= yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work -BACKLIGHT_ENABLE ?= yes # Enable numpad's backlight functionality -RGBLIGHT_ENABLE ?= yes -# MIDI_ENABLE ?= YES # MIDI controls -# UNICODE_ENABLE ?= YES # Unicode -# BLUETOOTH_ENABLE ?= yes # Enable Bluetooth with the Adafruit EZ-Key HID - - -ifndef QUANTUM_DIR +ifndef MAKEFILE_INCLUDED include ../../Makefile -endif +endif
\ No newline at end of file diff --git a/keyboards/cluepad/rules.mk b/keyboards/cluepad/rules.mk new file mode 100644 index 000000000..19b16b95a --- /dev/null +++ b/keyboards/cluepad/rules.mk @@ -0,0 +1,65 @@ + +# MCU name +#MCU = at90usb1287 +MCU = atmega32u4 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + +# Boot Section Size in *bytes* +# Teensy halfKay 512 +# Teensy++ halfKay 1024 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +# USBaspLoader 2048 +OPT_DEFS += -DBOOTLOADER_SIZE=4096 + + +# Build Options +# comment out to disable the options. +# +BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000) +# MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) +# EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) +# CONSOLE_ENABLE ?= yes # Console for debug(+400) +# COMMAND_ENABLE ?= yes # Commands for debug and configuration +NKRO_ENABLE ?= yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +BACKLIGHT_ENABLE ?= yes # Enable numpad's backlight functionality +RGBLIGHT_ENABLE ?= yes +# MIDI_ENABLE ?= YES # MIDI controls +# UNICODE_ENABLE ?= YES # Unicode +# BLUETOOTH_ENABLE ?= yes # Enable Bluetooth with the Adafruit EZ-Key HID
\ No newline at end of file diff --git a/keyboards/ergodox/Makefile b/keyboards/ergodox/Makefile index 05fb588d1..716535005 100644 --- a/keyboards/ergodox/Makefile +++ b/keyboards/ergodox/Makefile @@ -1,34 +1,5 @@ -#---------------------------------------------------------------------------- -# On command line: -# -# make = Make software. -# -# make clean = Clean out built project files. -# -# That's pretty much all you need. To compile, always go make clean, -# followed by make. -# -# For advanced users only: -# make teensy = Download the hex file to the device, using teensy_loader_cli. -# (must have teensy_loader_cli installed). -# -#---------------------------------------------------------------------------- SUBPROJECT_DEFAULT = ez -# Build Options -# comment out to disable the options. -# -BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000) -MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) -EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) -CONSOLE_ENABLE ?= no # Console for debug(+400) -COMMAND_ENABLE ?= yes # Commands for debug and configuration -CUSTOM_MATRIX ?= yes # Custom matrix file for the ErgoDox EZ -SLEEP_LED_ENABLE ?= yes # Breathing sleep LED during USB suspend -NKRO_ENABLE ?= yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work -MIDI_ENABLE ?= no # MIDI controls -UNICODE_ENABLE ?= yes # Unicode - -ifndef QUANTUM_DIR +ifndef MAKEFILE_INCLUDED include ../../Makefile -endif +endif
\ No newline at end of file diff --git a/keyboards/ergodox/rules.mk b/keyboards/ergodox/rules.mk new file mode 100644 index 000000000..ac63d4eff --- /dev/null +++ b/keyboards/ergodox/rules.mk @@ -0,0 +1,28 @@ +#---------------------------------------------------------------------------- +# On command line: +# +# make = Make software. +# +# make clean = Clean out built project files. +# +# That's pretty much all you need. To compile, always go make clean, +# followed by make. +# +# For advanced users only: +# make teensy = Download the hex file to the device, using teensy_loader_cli. +# (must have teensy_loader_cli installed). +# +#---------------------------------------------------------------------------- +# Build Options +# comment out to disable the options. +# +BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) +EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) +CONSOLE_ENABLE ?= no # Console for debug(+400) +COMMAND_ENABLE ?= yes # Commands for debug and configuration +CUSTOM_MATRIX ?= yes # Custom matrix file for the ErgoDox EZ +SLEEP_LED_ENABLE ?= yes # Breathing sleep LED during USB suspend +NKRO_ENABLE ?= yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +MIDI_ENABLE ?= no # MIDI controls +UNICODE_ENABLE ?= yes # Unicode diff --git a/keyboards/gh60/Makefile b/keyboards/gh60/Makefile index 39a9cc0ae..4e2a6f00f 100644 --- a/keyboards/gh60/Makefile +++ b/keyboards/gh60/Makefile @@ -1,74 +1,3 @@ -
-
-# MCU name
-#MCU = at90usb1287
-MCU = atmega32u4
-
-# Processor frequency.
-# This will define a symbol, F_CPU, in all source code files equal to the
-# processor frequency in Hz. You can then use this symbol in your source code to
-# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-# automatically to create a 32-bit value in your source code.
-#
-# This will be an integer division of F_USB below, as it is sourced by
-# F_USB after it has run through any CPU prescalers. Note that this value
-# does not *change* the processor frequency - it should merely be updated to
-# reflect the processor speed set externally so that the code can use accurate
-# software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-# This will define a symbol, F_USB, in all source code files equal to the
-# input clock frequency (before any prescaling is performed) in Hz. This value may
-# differ from F_CPU if prescaling is used on the latter, and is required as the
-# raw input clock is fed directly to the PLL sections of the AVR for high speed
-# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-# at the end, this will be done automatically to create a 32-bit value in your
-# source code.
-#
-# If no clock division is performed on the input clock inside the AVR (via the
-# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section Size in *bytes*
-# Teensy halfKay 512
-# Teensy++ halfKay 1024
-# Atmel DFU loader 4096
-# LUFA bootloader 4096
-# USBaspLoader 2048
-OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
-
-# Build Options
-# comment out to disable the options.
-#
-BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700)
-EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450)
-# CONSOLE_ENABLE ?= yes # Console for debug(+400)
-# COMMAND_ENABLE ?= yes # Commands for debug and configuration
-KEYBOARD_LOCK_ENABLE ?= yes # Allow locking of keyboard via magic key
-# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
-# SLEEP_LED_ENABLE ?= yes # Breathing sleep LED during USB suspend
-NKRO_ENABLE ?= yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
-# BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality
-# MIDI_ENABLE ?= YES # MIDI controls
-# UNICODE_ENABLE ?= YES # Unicode
-# BLUETOOTH_ENABLE ?= yes # Enable Bluetooth with the Adafruit EZ-Key HID
-
-
-ifndef QUANTUM_DIR
- include ../../Makefile
-endif
-
+ifndef MAKEFILE_INCLUDED + include ../../Makefile +endif
\ No newline at end of file diff --git a/keyboards/gh60/rules.mk b/keyboards/gh60/rules.mk new file mode 100644 index 000000000..73f4bd76e --- /dev/null +++ b/keyboards/gh60/rules.mk @@ -0,0 +1,68 @@ +
+
+# MCU name
+#MCU = at90usb1287
+MCU = atmega32u4
+
+# Processor frequency.
+# This will define a symbol, F_CPU, in all source code files equal to the
+# processor frequency in Hz. You can then use this symbol in your source code to
+# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+# automatically to create a 32-bit value in your source code.
+#
+# This will be an integer division of F_USB below, as it is sourced by
+# F_USB after it has run through any CPU prescalers. Note that this value
+# does not *change* the processor frequency - it should merely be updated to
+# reflect the processor speed set externally so that the code can use accurate
+# software delays.
+F_CPU = 16000000
+
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+# This will define a symbol, F_USB, in all source code files equal to the
+# input clock frequency (before any prescaling is performed) in Hz. This value may
+# differ from F_CPU if prescaling is used on the latter, and is required as the
+# raw input clock is fed directly to the PLL sections of the AVR for high speed
+# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+# at the end, this will be done automatically to create a 32-bit value in your
+# source code.
+#
+# If no clock division is performed on the input clock inside the AVR (via the
+# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+
+# Boot Section Size in *bytes*
+# Teensy halfKay 512
+# Teensy++ halfKay 1024
+# Atmel DFU loader 4096
+# LUFA bootloader 4096
+# USBaspLoader 2048
+OPT_DEFS += -DBOOTLOADER_SIZE=4096
+
+
+# Build Options
+# comment out to disable the options.
+#
+BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700)
+EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450)
+# CONSOLE_ENABLE ?= yes # Console for debug(+400)
+# COMMAND_ENABLE ?= yes # Commands for debug and configuration
+KEYBOARD_LOCK_ENABLE ?= yes # Allow locking of keyboard via magic key
+# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
+# SLEEP_LED_ENABLE ?= yes # Breathing sleep LED during USB suspend
+NKRO_ENABLE ?= yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+# BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality
+# MIDI_ENABLE ?= YES # MIDI controls
+# UNICODE_ENABLE ?= YES # Unicode
+# BLUETOOTH_ENABLE ?= yes # Enable Bluetooth with the Adafruit EZ-Key HID
diff --git a/keyboards/handwired/Makefile b/keyboards/handwired/Makefile index 57493a47c..4e2a6f00f 100644 --- a/keyboards/handwired/Makefile +++ b/keyboards/handwired/Makefile @@ -1,3 +1,3 @@ -ifndef QUANTUM_DIR +ifndef MAKEFILE_INCLUDED include ../../Makefile endif
\ No newline at end of file diff --git a/keyboards/handwired/onekey/Makefile b/keyboards/handwired/onekey/Makefile index c6d10856a..4e2a6f00f 100644 --- a/keyboards/handwired/onekey/Makefile +++ b/keyboards/handwired/onekey/Makefile @@ -1,65 +1,3 @@ - - -# MCU name -MCU = atmega32u4 - -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=4096 - - -# Build Options -# comment out to disable the options. -# -BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000) -MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) -EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) -CONSOLE_ENABLE ?= yes # Console for debug(+400) -COMMAND_ENABLE ?= yes # Commands for debug and configuration -#SLEEP_LED_ENABLE = yes # Breathing sleep LED during USB suspend -#NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA - -ifndef QUANTUM_DIR - include ../../../Makefile +ifndef MAKEFILE_INCLUDED + include ../../Makefile endif
\ No newline at end of file diff --git a/keyboards/handwired/rules.mk b/keyboards/handwired/rules.mk new file mode 100644 index 000000000..e69de29bb --- /dev/null +++ b/keyboards/handwired/rules.mk diff --git a/keyboards/hhkb/Makefile b/keyboards/hhkb/Makefile index 6fe973e1e..4e2a6f00f 100644 --- a/keyboards/hhkb/Makefile +++ b/keyboards/hhkb/Makefile @@ -1,90 +1,3 @@ - - -# project specific files -SRC = matrix.c - -# MCU name -#MCU = at90usb1287 -MCU = atmega32u4 - -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -#OPT_DEFS += -DBOOTLOADER_SIZE=4096 - -# as per original hasu settings -OPT_DEFS += -DBOOTLOADER_SIZE=512 - -# Build Options -# comment out to disable the options. -# -BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000) -MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) -EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) -CONSOLE_ENABLE ?= yes # Console for debug(+400) -COMMAND_ENABLE ?= yes # Commands for debug and configuration -CUSTOM_MATRIX ?= yes # Custom matrix file for the HHKB -# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE -# SLEEP_LED_ENABLE ?= yes # Breathing sleep LED during USB suspend -# NKRO_ENABLE ?= yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work -# BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality -# MIDI_ENABLE ?= YES # MIDI controls -# UNICODE_ENABLE ?= YES # Unicode -# BLUETOOTH_ENABLE ?= yes # Enable Bluetooth with the Adafruit EZ-Key HID - - - -ifndef QUANTUM_DIR +ifndef MAKEFILE_INCLUDED include ../../Makefile -endif - -ifneq (, $(findstring yes, $(HHKB_JP))) - OPT_DEFS += -DHHKB_JP -endif - -debug-on: EXTRAFLAGS += -DDEBUG -DDEBUG_ACTION -debug-on: all - -debug-off: EXTRAFLAGS += -DNO_DEBUG -DNO_PRINT -debug-off: OPT_DEFS := $(filter-out -DCONSOLE_ENABLE,$(OPT_DEFS)) -debug-off: all +endif
\ No newline at end of file diff --git a/keyboards/hhkb/rules.mk b/keyboards/hhkb/rules.mk new file mode 100644 index 000000000..b43b5e23f --- /dev/null +++ b/keyboards/hhkb/rules.mk @@ -0,0 +1,84 @@ + + +# project specific files +SRC = matrix.c + +# MCU name +#MCU = at90usb1287 +MCU = atmega32u4 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + +# Boot Section Size in *bytes* +# Teensy halfKay 512 +# Teensy++ halfKay 1024 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +# USBaspLoader 2048 +#OPT_DEFS += -DBOOTLOADER_SIZE=4096 + +# as per original hasu settings +OPT_DEFS += -DBOOTLOADER_SIZE=512 + +# Build Options +# comment out to disable the options. +# +BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) +EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) +CONSOLE_ENABLE ?= yes # Console for debug(+400) +COMMAND_ENABLE ?= yes # Commands for debug and configuration +CUSTOM_MATRIX ?= yes # Custom matrix file for the HHKB +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +# SLEEP_LED_ENABLE ?= yes # Breathing sleep LED during USB suspend +# NKRO_ENABLE ?= yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +# BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality +# MIDI_ENABLE ?= YES # MIDI controls +# UNICODE_ENABLE ?= YES # Unicode +# BLUETOOTH_ENABLE ?= yes # Enable Bluetooth with the Adafruit EZ-Key HID + +ifneq (, $(findstring yes, $(HHKB_JP))) + OPT_DEFS += -DHHKB_JP +endif + +debug-on: EXTRAFLAGS += -DDEBUG -DDEBUG_ACTION +debug-on: all + +debug-off: EXTRAFLAGS += -DNO_DEBUG -DNO_PRINT +debug-off: OPT_DEFS := $(filter-out -DCONSOLE_ENABLE,$(OPT_DEFS)) +debug-off: all diff --git a/keyboards/infinity_chibios/Makefile b/keyboards/infinity_chibios/Makefile index 649b43e64..4e2a6f00f 100644 --- a/keyboards/infinity_chibios/Makefile +++ b/keyboards/infinity_chibios/Makefile @@ -1,70 +1,3 @@ -# project specific files -SRC = matrix.c \ - led.c - -## chip/board settings -# - the next two should match the directories in -# <chibios>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES) -# - For Teensies, FAMILY = KINETIS and SERIES is either -# KL2x (LC) or K20x (3.0,3.1,3.2). -# - For Infinity KB, SERIES = K20x -MCU_FAMILY = KINETIS -MCU_SERIES = K20x - -# Linker script to use -# - it should exist either in <chibios>/os/common/ports/ARMCMx/compilers/GCC/ld/ -# or <this_dir>/ld/ -# - NOTE: a custom ld script is needed for EEPROM on Teensy LC -# - LDSCRIPT = -# - MKL26Z64 for Teensy LC -# - MK20DX128 for Teensy 3.0 -# - MK20DX256 for Teensy 3.1 and 3.2 -# - MK20DX128BLDR4 for Infinity with Kiibohd bootloader -MCU_LDSCRIPT = MK20DX128BLDR4 - -# Startup code to use -# - it should exist in <chibios>/os/common/ports/ARMCMx/compilers/GCC/mk/ -# - STARTUP = -# - kl2x for Teensy LC -# - k20x5 for Teensy 3.0 and Infinity KB -# - k20x7 for Teensy 3.1 and 3.2 -MCU_STARTUP = k20x5 - -# Board: it should exist either in <chibios>/os/hal/boards/ -# or <this_dir>/boards -# - BOARD = -# - PJRC_TEENSY_LC for Teensy LC -# - PJRC_TEENSY_3 for Teensy 3.0 -# - PJRC_TEENSY_3_1 for Teensy 3.1 or 3.2 -# - MCHCK_K20 for Infinity KB -BOARD = MCHCK_K20 - -# Cortex version -# Teensy LC is cortex-m0; Teensy 3.x are cortex-m4 -MCU = cortex-m4 - -# ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7 -# I.e. 6 for Teensy LC; 7 for Teensy 3.x -ARMV = 7 - -# Vector table for application -# 0x00000000-0x00001000 area is occupied by bootlaoder.*/ -# The CORTEX_VTOR... is needed only for MCHCK/Infinity KB -OPT_DEFS = -DCORTEX_VTOR_INIT=0x00001000 - -# Build Options -# comment out to disable the options. -# -BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration -## (Note that for BOOTMAGIC on Teensy LC you have to use a custom .ld script.) -MOUSEKEY_ENABLE ?= yes # Mouse keys -EXTRAKEY_ENABLE ?= yes # Audio control and System control -CONSOLE_ENABLE ?= yes # Console for debug -COMMAND_ENABLE ?= yes # Commands for debug and configuration -SLEEP_LED_ENABLE ?= yes # Breathing sleep LED during USB suspend -NKRO_ENABLE ?= yes # USB Nkey Rollover -CUSTOM_MATRIX ?= yes # Custom matrix file - -ifndef QUANTUM_DIR +ifndef MAKEFILE_INCLUDED include ../../Makefile endif
\ No newline at end of file diff --git a/keyboards/infinity_chibios/rules.mk b/keyboards/infinity_chibios/rules.mk new file mode 100644 index 000000000..56d6470b5 --- /dev/null +++ b/keyboards/infinity_chibios/rules.mk @@ -0,0 +1,66 @@ +# project specific files +SRC = matrix.c \ + led.c + +## chip/board settings +# - the next two should match the directories in +# <chibios>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES) +# - For Teensies, FAMILY = KINETIS and SERIES is either +# KL2x (LC) or K20x (3.0,3.1,3.2). +# - For Infinity KB, SERIES = K20x +MCU_FAMILY = KINETIS +MCU_SERIES = K20x + +# Linker script to use +# - it should exist either in <chibios>/os/common/ports/ARMCMx/compilers/GCC/ld/ +# or <this_dir>/ld/ +# - NOTE: a custom ld script is needed for EEPROM on Teensy LC +# - LDSCRIPT = +# - MKL26Z64 for Teensy LC +# - MK20DX128 for Teensy 3.0 +# - MK20DX256 for Teensy 3.1 and 3.2 +# - MK20DX128BLDR4 for Infinity with Kiibohd bootloader +MCU_LDSCRIPT = MK20DX128BLDR4 + +# Startup code to use +# - it should exist in <chibios>/os/common/ports/ARMCMx/compilers/GCC/mk/ +# - STARTUP = +# - kl2x for Teensy LC +# - k20x5 for Teensy 3.0 and Infinity KB +# - k20x7 for Teensy 3.1 and 3.2 +MCU_STARTUP = k20x5 + +# Board: it should exist either in <chibios>/os/hal/boards/ +# or <this_dir>/boards +# - BOARD = +# - PJRC_TEENSY_LC for Teensy LC +# - PJRC_TEENSY_3 for Teensy 3.0 +# - PJRC_TEENSY_3_1 for Teensy 3.1 or 3.2 +# - MCHCK_K20 for Infinity KB +BOARD = MCHCK_K20 + +# Cortex version +# Teensy LC is cortex-m0; Teensy 3.x are cortex-m4 +MCU = cortex-m4 + +# ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7 +# I.e. 6 for Teensy LC; 7 for Teensy 3.x +ARMV = 7 + +# Vector table for application +# 0x00000000-0x00001000 area is occupied by bootlaoder.*/ +# The CORTEX_VTOR... is needed only for MCHCK/Infinity KB +OPT_DEFS = -DCORTEX_VTOR_INIT=0x00001000 + +# Build Options +# comment out to disable the options. +# +BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration +## (Note that for BOOTMAGIC on Teensy LC you have to use a custom .ld script.) +MOUSEKEY_ENABLE ?= yes # Mouse keys +EXTRAKEY_ENABLE ?= yes # Audio control and System control +CONSOLE_ENABLE ?= yes # Console for debug +COMMAND_ENABLE ?= yes # Commands for debug and configuration +SLEEP_LED_ENABLE ?= yes # Breathing sleep LED during USB suspend +NKRO_ENABLE ?= yes # USB Nkey Rollover +CUSTOM_MATRIX ?= yes # Custom matrix file
\ No newline at end of file diff --git a/keyboards/jd45/Makefile b/keyboards/jd45/Makefile index 75d544f16..4e2a6f00f 100644 --- a/keyboards/jd45/Makefile +++ b/keyboards/jd45/Makefile @@ -1,71 +1,3 @@ - - -# MCU name -#MCU = at90usb1287 -MCU = atmega32u4 - -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=4096 - - -# Build Options -# comment out to disable the options. -# -BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000) -MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) -EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) -CONSOLE_ENABLE ?= yes # Console for debug(+400) -COMMAND_ENABLE ?= yes # Commands for debug and configuration -# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE -# SLEEP_LED_ENABLE ?= yes # Breathing sleep LED during USB suspend -# NKRO_ENABLE ?= yes # USB Nkey Rollover - not yet supported in LUFA -BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality -MIDI_ENABLE ?= YES # MIDI controls -# UNICODE_ENABLE ?= YES # Unicode -BLUETOOTH_ENABLE ?= yes # Enable Bluetooth with the Adafruit EZ-Key HID - -ifndef QUANTUM_DIR +ifndef MAKEFILE_INCLUDED include ../../Makefile -endif +endif
\ No newline at end of file diff --git a/keyboards/jd45/rules.mk b/keyboards/jd45/rules.mk new file mode 100644 index 000000000..2f1e266a1 --- /dev/null +++ b/keyboards/jd45/rules.mk @@ -0,0 +1,67 @@ + + +# MCU name +#MCU = at90usb1287 +MCU = atmega32u4 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + +# Boot Section Size in *bytes* +# Teensy halfKay 512 +# Teensy++ halfKay 1024 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +# USBaspLoader 2048 +OPT_DEFS += -DBOOTLOADER_SIZE=4096 + + +# Build Options +# comment out to disable the options. +# +BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) +EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) +CONSOLE_ENABLE ?= yes # Console for debug(+400) +COMMAND_ENABLE ?= yes # Commands for debug and configuration +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +# SLEEP_LED_ENABLE ?= yes # Breathing sleep LED during USB suspend +# NKRO_ENABLE ?= yes # USB Nkey Rollover - not yet supported in LUFA +BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality +MIDI_ENABLE ?= YES # MIDI controls +# UNICODE_ENABLE ?= YES # Unicode +BLUETOOTH_ENABLE ?= yes # Enable Bluetooth with the Adafruit EZ-Key HID
\ No newline at end of file diff --git a/keyboards/kc60/Makefile b/keyboards/kc60/Makefile index b00a488b9..4e2a6f00f 100644 --- a/keyboards/kc60/Makefile +++ b/keyboards/kc60/Makefile @@ -1,76 +1,3 @@ - - -# MCU name -#MCU = at90usb1287 -MCU = atmega32u4 - -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=4096 - - -# Build Options -# change yes to no to disable -# -BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000) -MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) -EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) -CONSOLE_ENABLE ?= yes # Console for debug(+400) -COMMAND_ENABLE ?= yes # Commands for debug and configuration -KEYBOARD_LOCK_ENABLE ?= yes # Allow locking of keyboard via magic key -# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE -SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend -# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work -NKRO_ENABLE ?= no # USB Nkey Rollover -BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality -MIDI_ENABLE ?= no # MIDI controls -UNICODE_ENABLE ?= no # Unicode -BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID -AUDIO_ENABLE ?= no # Audio output on port C6 - - -ifndef QUANTUM_DIR +ifndef MAKEFILE_INCLUDED include ../../Makefile -endif - +endif
\ No newline at end of file diff --git a/keyboards/kc60/rules.mk b/keyboards/kc60/rules.mk new file mode 100644 index 000000000..4efd6f988 --- /dev/null +++ b/keyboards/kc60/rules.mk @@ -0,0 +1,70 @@ + + +# MCU name +#MCU = at90usb1287 +MCU = atmega32u4 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + +# Boot Section Size in *bytes* +# Teensy halfKay 512 +# Teensy++ halfKay 1024 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +# USBaspLoader 2048 +OPT_DEFS += -DBOOTLOADER_SIZE=4096 + + +# Build Options +# change yes to no to disable +# +BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) +EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) +CONSOLE_ENABLE ?= yes # Console for debug(+400) +COMMAND_ENABLE ?= yes # Commands for debug and configuration +KEYBOARD_LOCK_ENABLE ?= yes # Allow locking of keyboard via magic key +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend +# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +NKRO_ENABLE ?= no # USB Nkey Rollover +BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality +MIDI_ENABLE ?= no # MIDI controls +UNICODE_ENABLE ?= no # Unicode +BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID +AUDIO_ENABLE ?= no # Audio output on port C6 diff --git a/keyboards/kinesis/Makefile b/keyboards/kinesis/Makefile index ca077e636..4e2a6f00f 100644 --- a/keyboards/kinesis/Makefile +++ b/keyboards/kinesis/Makefile @@ -1,79 +1,3 @@ - -## Project specific files - -SRC= matrix.c - -# MCU name -MCU = at90usb1286 -#MCU = atmega32u4 - -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=1024 - - -# Build Options -# change yes to no to disable -# -BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000) -MOUSEKEY_ENABLE = yes # Mouse keys(+4700) -EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) -CONSOLE_ENABLE ?= no # Console for debug(+400) -COMMAND_ENABLE ?= no -# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE -SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend -# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work -NKRO_ENABLE ?= no # USB Nkey Rollover -BACKLIGHT_ENABLE ?= no # Enable keyboard backlight functionality on B7 by default -MIDI_ENABLE ?= no # MIDI controls -UNICODE_ENABLE ?= no # Unicode -BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID -AUDIO_ENABLE = no # Audio output should be port E6, current quantum library hardcodes C6, which we use for programming -CUSTOM_MATRIX=yes # need to do our own thing with the matrix - -ifndef QUANTUM_DIR +ifndef MAKEFILE_INCLUDED include ../../Makefile -endif - - +endif
\ No newline at end of file diff --git a/keyboards/kinesis/rules.mk b/keyboards/kinesis/rules.mk new file mode 100644 index 000000000..a4a2b7d15 --- /dev/null +++ b/keyboards/kinesis/rules.mk @@ -0,0 +1,73 @@ + +## Project specific files + +SRC= matrix.c + +# MCU name +MCU = at90usb1286 +#MCU = atmega32u4 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + +# Boot Section Size in *bytes* +# Teensy halfKay 512 +# Teensy++ halfKay 1024 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +# USBaspLoader 2048 +OPT_DEFS += -DBOOTLOADER_SIZE=1024 + + +# Build Options +# change yes to no to disable +# +BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE = yes # Mouse keys(+4700) +EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) +CONSOLE_ENABLE ?= no # Console for debug(+400) +COMMAND_ENABLE ?= no +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend +# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +NKRO_ENABLE ?= no # USB Nkey Rollover +BACKLIGHT_ENABLE ?= no # Enable keyboard backlight functionality on B7 by default +MIDI_ENABLE ?= no # MIDI controls +UNICODE_ENABLE ?= no # Unicode +BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID +AUDIO_ENABLE = no # Audio output should be port E6, current quantum library hardcodes C6, which we use for programming +CUSTOM_MATRIX=yes # need to do our own thing with the matrix diff --git a/keyboards/lets_split/Makefile b/keyboards/lets_split/Makefile index b9f07636b..4e2a6f00f 100644 --- a/keyboards/lets_split/Makefile +++ b/keyboards/lets_split/Makefile @@ -1,78 +1,3 @@ -SRC += matrix.c \ - i2c.c \ - split_util.c \ - serial.c - -# MCU name -#MCU = at90usb1287 -MCU = atmega32u4 - -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=4096 - -# Build Options -# change to "no" to disable the options, or define them in the Makefile in -# the appropriate keymap folder that will get included automatically -# -BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000) -MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) -EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) -CONSOLE_ENABLE ?= no # Console for debug(+400) -COMMAND_ENABLE ?= yes # Commands for debug and configuration -NKRO_ENABLE ?= no # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work -BACKLIGHT_ENABLE ?= no # Enable keyboard backlight functionality -MIDI_ENABLE ?= no # MIDI controls -AUDIO_ENABLE ?= yes # Audio output on port C6 -UNICODE_ENABLE ?= no # Unicode -BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID -RGBLIGHT_ENABLE ?= no # Enable WS2812 RGB underlight. Do not enable this with audio at the same time. - -# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE -SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend - -CUSTOM_MATRIX = yes - -ifndef QUANTUM_DIR +ifndef MAKEFILE_INCLUDED include ../../Makefile endif
\ No newline at end of file diff --git a/keyboards/lets_split/rules.mk b/keyboards/lets_split/rules.mk new file mode 100644 index 000000000..6961fbd55 --- /dev/null +++ b/keyboards/lets_split/rules.mk @@ -0,0 +1,74 @@ +SRC += matrix.c \ + i2c.c \ + split_util.c \ + serial.c + +# MCU name +#MCU = at90usb1287 +MCU = atmega32u4 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + +# Boot Section Size in *bytes* +# Teensy halfKay 512 +# Teensy++ halfKay 1024 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +# USBaspLoader 2048 +OPT_DEFS += -DBOOTLOADER_SIZE=4096 + +# Build Options +# change to "no" to disable the options, or define them in the Makefile in +# the appropriate keymap folder that will get included automatically +# +BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) +EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) +CONSOLE_ENABLE ?= no # Console for debug(+400) +COMMAND_ENABLE ?= yes # Commands for debug and configuration +NKRO_ENABLE ?= no # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +BACKLIGHT_ENABLE ?= no # Enable keyboard backlight functionality +MIDI_ENABLE ?= no # MIDI controls +AUDIO_ENABLE ?= yes # Audio output on port C6 +UNICODE_ENABLE ?= no # Unicode +BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID +RGBLIGHT_ENABLE ?= no # Enable WS2812 RGB underlight. Do not enable this with audio at the same time. + +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend + +CUSTOM_MATRIX = yes
\ No newline at end of file diff --git a/keyboards/phantom/Makefile b/keyboards/phantom/Makefile index 3a71fd0ee..4e2a6f00f 100644 --- a/keyboards/phantom/Makefile +++ b/keyboards/phantom/Makefile @@ -1,74 +1,3 @@ - - -SRC = led.c - -# MCU name -#MCU = at90usb1287 -MCU = atmega32u4 - -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=4096 - - -# Build Options -# comment out to disable the options. -# -BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000) -MOUSEKEY_ENABLE ?= no # Mouse keys(+4700) -EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) -CONSOLE_ENABLE ?= yes # Console for debug(+400) -COMMAND_ENABLE ?= yes # Commands for debug and configuration -NKRO_ENABLE ?= yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work -RGBLIGHT_ENABLE ?=yes # Enable keyboard underlight functionality (+4870) -BACKLIGHT_ENABLE ?= no # Enable keyboard backlight functionality (+1150) -MIDI_ENABLE ?= no # MIDI controls -AUDIO_ENABLE ?= no -UNICODE_ENABLE ?= no # Unicode -BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID - - -ifndef QUANTUM_DIR +ifndef MAKEFILE_INCLUDED include ../../Makefile -endif +endif
\ No newline at end of file diff --git a/keyboards/phantom/rules.mk b/keyboards/phantom/rules.mk new file mode 100644 index 000000000..c6b8ca6c3 --- /dev/null +++ b/keyboards/phantom/rules.mk @@ -0,0 +1,69 @@ + + +SRC = led.c + +# MCU name +#MCU = at90usb1287 +MCU = atmega32u4 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + +# Boot Section Size in *bytes* +# Teensy halfKay 512 +# Teensy++ halfKay 1024 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +# USBaspLoader 2048 +OPT_DEFS += -DBOOTLOADER_SIZE=4096 + + +# Build Options +# comment out to disable the options. +# +BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE ?= no # Mouse keys(+4700) +EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) +CONSOLE_ENABLE ?= yes # Console for debug(+400) +COMMAND_ENABLE ?= yes # Commands for debug and configuration +NKRO_ENABLE ?= yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +RGBLIGHT_ENABLE ?=yes # Enable keyboard underlight functionality (+4870) +BACKLIGHT_ENABLE ?= no # Enable keyboard backlight functionality (+1150) +MIDI_ENABLE ?= no # MIDI controls +AUDIO_ENABLE ?= no +UNICODE_ENABLE ?= no # Unicode +BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID diff --git a/keyboards/planck/Makefile b/keyboards/planck/Makefile index 23944f92e..7d49c5ef9 100644 --- a/keyboards/planck/Makefile +++ b/keyboards/planck/Makefile @@ -1,74 +1,5 @@ - SUBPROJECT_DEFAULT = rev4 -# MCU name -#MCU = at90usb1287 -MCU = atmega32u4 - -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=4096 - -# Build Options -# change to "no" to disable the options, or define them in the Makefile in -# the appropriate keymap folder that will get included automatically -# -BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000) -MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) -EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) -CONSOLE_ENABLE ?= no # Console for debug(+400) -COMMAND_ENABLE ?= yes # Commands for debug and configuration -NKRO_ENABLE ?= no # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work -BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality -MIDI_ENABLE ?= no # MIDI controls -AUDIO_ENABLE ?= no # Audio output on port C6 -UNICODE_ENABLE ?= no # Unicode -BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID -RGBLIGHT_ENABLE ?= no # Enable WS2812 RGB underlight. Do not enable this with audio at the same time. - -# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE -SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend - -ifndef QUANTUM_DIR +ifndef MAKEFILE_INCLUDED include ../../Makefile endif
\ No newline at end of file diff --git a/keyboards/planck/rules.mk b/keyboards/planck/rules.mk new file mode 100644 index 000000000..25db53a31 --- /dev/null +++ b/keyboards/planck/rules.mk @@ -0,0 +1,67 @@ +# MCU name +#MCU = at90usb1287 +MCU = atmega32u4 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + +# Boot Section Size in *bytes* +# Teensy halfKay 512 +# Teensy++ halfKay 1024 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +# USBaspLoader 2048 +OPT_DEFS += -DBOOTLOADER_SIZE=4096 + +# Build Options +# change to "no" to disable the options, or define them in the Makefile in +# the appropriate keymap folder that will get included automatically +# +BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) +EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) +CONSOLE_ENABLE ?= no # Console for debug(+400) +COMMAND_ENABLE ?= yes # Commands for debug and configuration +NKRO_ENABLE ?= no # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality +MIDI_ENABLE ?= no # MIDI controls +AUDIO_ENABLE ?= no # Audio output on port C6 +UNICODE_ENABLE ?= no # Unicode +BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID +RGBLIGHT_ENABLE ?= no # Enable WS2812 RGB underlight. Do not enable this with audio at the same time. + +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend
\ No newline at end of file diff --git a/keyboards/preonic/Makefile b/keyboards/preonic/Makefile index 08e9205cb..4e2a6f00f 100644 --- a/keyboards/preonic/Makefile +++ b/keyboards/preonic/Makefile @@ -1,73 +1,3 @@ - - -# MCU name -#MCU = at90usb1287 -MCU = atmega32u4 - -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=4096 - -# Build Options -# change to "no" to disable the options, or define them in the Makefile in -# the appropriate keymap folder that will get included automatically -# -BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000) -MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) -EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) -CONSOLE_ENABLE ?= no # Console for debug(+400) -COMMAND_ENABLE ?= yes # Commands for debug and configuration -NKRO_ENABLE ?= no # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work -BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality -MIDI_ENABLE ?= no # MIDI controls -AUDIO_ENABLE ?= no # Audio output on port C6 -UNICODE_ENABLE ?= no # Unicode -BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID -RGBLIGHT_ENABLE ?= no # Enable WS2812 RGB underlight. Do not enable this with audio at the same time. - -# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE -SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend - -ifndef QUANTUM_DIR +ifndef MAKEFILE_INCLUDED include ../../Makefile endif
\ No newline at end of file diff --git a/keyboards/preonic/rules.mk b/keyboards/preonic/rules.mk new file mode 100644 index 000000000..d0f3a3a1c --- /dev/null +++ b/keyboards/preonic/rules.mk @@ -0,0 +1,69 @@ + + +# MCU name +#MCU = at90usb1287 +MCU = atmega32u4 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + +# Boot Section Size in *bytes* +# Teensy halfKay 512 +# Teensy++ halfKay 1024 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +# USBaspLoader 2048 +OPT_DEFS += -DBOOTLOADER_SIZE=4096 + +# Build Options +# change to "no" to disable the options, or define them in the Makefile in +# the appropriate keymap folder that will get included automatically +# +BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) +EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) +CONSOLE_ENABLE ?= no # Console for debug(+400) +COMMAND_ENABLE ?= yes # Commands for debug and configuration +NKRO_ENABLE ?= no # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality +MIDI_ENABLE ?= no # MIDI controls +AUDIO_ENABLE ?= no # Audio output on port C6 +UNICODE_ENABLE ?= no # Unicode +BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID +RGBLIGHT_ENABLE ?= no # Enable WS2812 RGB underlight. Do not enable this with audio at the same time. + +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend
\ No newline at end of file diff --git a/keyboards/retro_refit/Makefile b/keyboards/retro_refit/Makefile index 2dd8cc5f7..4e2a6f00f 100644 --- a/keyboards/retro_refit/Makefile +++ b/keyboards/retro_refit/Makefile @@ -1,74 +1,3 @@ - - -# MCU name -#MCU = at90usb1287 -MCU = atmega32u4 - -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=512 - - -# Build Options -# comment out to disable the options. -# -BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000) -MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) -EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) -CONSOLE_ENABLE ?= yes # Console for debug(+400) -COMMAND_ENABLE ?= yes # Commands for debug and configuration -KEYBOARD_LOCK_ENABLE ?= yes # Allow locking of keyboard via magic key -# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE -# SLEEP_LED_ENABLE ?= yes # Breathing sleep LED during USB suspend -NKRO_ENABLE ?= yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work -# BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality -# MIDI_ENABLE ?= YES # MIDI controls -# UNICODE_ENABLE ?= YES # Unicode -# BLUETOOTH_ENABLE ?= yes # Enable Bluetooth with the Adafruit EZ-Key HID - - -ifndef QUANTUM_DIR +ifndef MAKEFILE_INCLUDED include ../../Makefile -endif - +endif
\ No newline at end of file diff --git a/keyboards/retro_refit/rules.mk b/keyboards/retro_refit/rules.mk new file mode 100644 index 000000000..10fbfa5c9 --- /dev/null +++ b/keyboards/retro_refit/rules.mk @@ -0,0 +1,68 @@ + + +# MCU name +#MCU = at90usb1287 +MCU = atmega32u4 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + +# Boot Section Size in *bytes* +# Teensy halfKay 512 +# Teensy++ halfKay 1024 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +# USBaspLoader 2048 +OPT_DEFS += -DBOOTLOADER_SIZE=512 + + +# Build Options +# comment out to disable the options. +# +BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) +EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) +CONSOLE_ENABLE ?= yes # Console for debug(+400) +COMMAND_ENABLE ?= yes # Commands for debug and configuration +KEYBOARD_LOCK_ENABLE ?= yes # Allow locking of keyboard via magic key +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +# SLEEP_LED_ENABLE ?= yes # Breathing sleep LED during USB suspend +NKRO_ENABLE ?= yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +# BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality +# MIDI_ENABLE ?= YES # MIDI controls +# UNICODE_ENABLE ?= YES # Unicode +# BLUETOOTH_ENABLE ?= yes # Enable Bluetooth with the Adafruit EZ-Key HID diff --git a/keyboards/s60-x/Makefile b/keyboards/s60-x/Makefile index 8b51d4609..4e2a6f00f 100644 --- a/keyboards/s60-x/Makefile +++ b/keyboards/s60-x/Makefile @@ -1,75 +1,3 @@ - - -# MCU name -#MCU = at90usb1287 -MCU = atmega32u4 - -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=4096 - - -# Build Options -# change yes to no to disable -# -BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000) -MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) -EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) -CONSOLE_ENABLE ?= yes # Console for debug(+400) -COMMAND_ENABLE ?= yes # Commands for debug and configuration -# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE -SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend -# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work -NKRO_ENABLE ?= no # USB Nkey Rollover -BACKLIGHT_ENABLE ?= no # Enable keyboard backlight functionality on B7 by default -MIDI_ENABLE ?= no # MIDI controls -UNICODE_ENABLE ?= no # Unicode -BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID -AUDIO_ENABLE ?= no # Audio output on port C6 - -ifndef QUANTUM_DIR +ifndef MAKEFILE_INCLUDED include ../../Makefile -endif - - +endif
\ No newline at end of file diff --git a/keyboards/s60-x/rules.mk b/keyboards/s60-x/rules.mk new file mode 100644 index 000000000..7ec93933a --- /dev/null +++ b/keyboards/s60-x/rules.mk @@ -0,0 +1,69 @@ + + +# MCU name +#MCU = at90usb1287 +MCU = atmega32u4 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + +# Boot Section Size in *bytes* +# Teensy halfKay 512 +# Teensy++ halfKay 1024 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +# USBaspLoader 2048 +OPT_DEFS += -DBOOTLOADER_SIZE=4096 + + +# Build Options +# change yes to no to disable +# +BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) +EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) +CONSOLE_ENABLE ?= yes # Console for debug(+400) +COMMAND_ENABLE ?= yes # Commands for debug and configuration +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend +# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +NKRO_ENABLE ?= no # USB Nkey Rollover +BACKLIGHT_ENABLE ?= no # Enable keyboard backlight functionality on B7 by default +MIDI_ENABLE ?= no # MIDI controls +UNICODE_ENABLE ?= no # Unicode +BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID +AUDIO_ENABLE ?= no # Audio output on port C6
\ No newline at end of file diff --git a/keyboards/satan/Makefile b/keyboards/satan/Makefile index a0879fc9c..4e2a6f00f 100644 --- a/keyboards/satan/Makefile +++ b/keyboards/satan/Makefile @@ -1,70 +1,3 @@ - -# MCU name -#MCU = at90usb1287 -MCU = atmega32u4 - -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=4096 - - -# Build Options -# comment out to disable the options. -# -BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000) -MOUSEKEY_ENABLE ?= no # Mouse keys(+4700) -EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) -CONSOLE_ENABLE ?= yes # Console for debug(+400) -COMMAND_ENABLE ?= yes # Commands for debug and configuration -NKRO_ENABLE ?= yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work -RGBLIGHT_ENABLE ?= yes # Enable keyboard underlight functionality (+4870) -BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality (+1150) -MIDI_ENABLE ?= no # MIDI controls -AUDIO_ENABLE ?= no -UNICODE_ENABLE ?= no # Unicode -BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID - -ifndef QUANTUM_DIR +ifndef MAKEFILE_INCLUDED include ../../Makefile -endif +endif
\ No newline at end of file diff --git a/keyboards/satan/rules.mk b/keyboards/satan/rules.mk new file mode 100644 index 000000000..1102584d8 --- /dev/null +++ b/keyboards/satan/rules.mk @@ -0,0 +1,66 @@ + +# MCU name +#MCU = at90usb1287 +MCU = atmega32u4 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + +# Boot Section Size in *bytes* +# Teensy halfKay 512 +# Teensy++ halfKay 1024 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +# USBaspLoader 2048 +OPT_DEFS += -DBOOTLOADER_SIZE=4096 + + +# Build Options +# comment out to disable the options. +# +BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE ?= no # Mouse keys(+4700) +EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) +CONSOLE_ENABLE ?= yes # Console for debug(+400) +COMMAND_ENABLE ?= yes # Commands for debug and configuration +NKRO_ENABLE ?= yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +RGBLIGHT_ENABLE ?= yes # Enable keyboard underlight functionality (+4870) +BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality (+1150) +MIDI_ENABLE ?= no # MIDI controls +AUDIO_ENABLE ?= no +UNICODE_ENABLE ?= no # Unicode +BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID diff --git a/keyboards/sixkeyboard/Makefile b/keyboards/sixkeyboard/Makefile index 6f273064a..4e2a6f00f 100644 --- a/keyboards/sixkeyboard/Makefile +++ b/keyboards/sixkeyboard/Makefile @@ -1,75 +1,3 @@ - - -SRC = matrix.c - -# MCU name -#MCU = at90usb1287 -MCU = atmega16u2 - -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=4096 - - -# Build Options -# comment out to disable the options. -# -BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000) -MOUSEKEY_ENABLE ?= no # Mouse keys(+4700) -EXTRAKEY_ENABLE ?= no # Audio control and System control(+450) -CONSOLE_ENABLE ?= no # Console for debug(+400) -COMMAND_ENABLE ?= no # Commands for debug and configuration -SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend -NKRO_ENABLE ?= no # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work -BACKLIGHT_ENABLE ?= no # Enable keyboard backlight functionality -MIDI_ENABLE ?= no # MIDI controls -AUDIO_ENABLE ?= no -UNICODE_ENABLE ?= no # Unicode -BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID -CUSTOM_MATRIX = yes - -ifndef QUANTUM_DIR +ifndef MAKEFILE_INCLUDED include ../../Makefile -endif - +endif
\ No newline at end of file diff --git a/keyboards/sixkeyboard/rules.mk b/keyboards/sixkeyboard/rules.mk new file mode 100644 index 000000000..2c99985a9 --- /dev/null +++ b/keyboards/sixkeyboard/rules.mk @@ -0,0 +1,70 @@ + + +SRC = matrix.c + +# MCU name +#MCU = at90usb1287 +MCU = atmega16u2 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + +# Boot Section Size in *bytes* +# Teensy halfKay 512 +# Teensy++ halfKay 1024 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +# USBaspLoader 2048 +OPT_DEFS += -DBOOTLOADER_SIZE=4096 + + +# Build Options +# comment out to disable the options. +# +BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE ?= no # Mouse keys(+4700) +EXTRAKEY_ENABLE ?= no # Audio control and System control(+450) +CONSOLE_ENABLE ?= no # Console for debug(+400) +COMMAND_ENABLE ?= no # Commands for debug and configuration +SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend +NKRO_ENABLE ?= no # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +BACKLIGHT_ENABLE ?= no # Enable keyboard backlight functionality +MIDI_ENABLE ?= no # MIDI controls +AUDIO_ENABLE ?= no +UNICODE_ENABLE ?= no # Unicode +BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID +CUSTOM_MATRIX = yes
\ No newline at end of file diff --git a/keyboards/tv44/Makefile b/keyboards/tv44/Makefile index 45ca12780..4e2a6f00f 100644 --- a/keyboards/tv44/Makefile +++ b/keyboards/tv44/Makefile @@ -1,75 +1,3 @@ - - -# MCU name -#MCU = at90usb1287 -MCU = atmega32u4 - -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=4096 - - -# Build Options -# change yes to no to disable -# -BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000) -MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) -EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) -CONSOLE_ENABLE ?= yes # Console for debug(+400) -COMMAND_ENABLE ?= yes # Commands for debug and configuration -# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE -SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend -# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work -NKRO_ENABLE ?= yes # USB Nkey Rollover -BACKLIGHT_ENABLE ?= no # Enable keyboard backlight functionality on B7 by default -MIDI_ENABLE ?= no # MIDI controls -UNICODE_ENABLE ?= no # Unicode -BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID -AUDIO_ENABLE ?= no # Audio output on port C6 - -ifndef QUANTUM_DIR +ifndef MAKEFILE_INCLUDED include ../../Makefile -endif - - +endif
\ No newline at end of file diff --git a/keyboards/tv44/rules.mk b/keyboards/tv44/rules.mk new file mode 100644 index 000000000..dbba6bace --- /dev/null +++ b/keyboards/tv44/rules.mk @@ -0,0 +1,69 @@ + + +# MCU name +#MCU = at90usb1287 +MCU = atmega32u4 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + +# Boot Section Size in *bytes* +# Teensy halfKay 512 +# Teensy++ halfKay 1024 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +# USBaspLoader 2048 +OPT_DEFS += -DBOOTLOADER_SIZE=4096 + + +# Build Options +# change yes to no to disable +# +BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) +EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) +CONSOLE_ENABLE ?= yes # Console for debug(+400) +COMMAND_ENABLE ?= yes # Commands for debug and configuration +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend +# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +NKRO_ENABLE ?= yes # USB Nkey Rollover +BACKLIGHT_ENABLE ?= no # Enable keyboard backlight functionality on B7 by default +MIDI_ENABLE ?= no # MIDI controls +UNICODE_ENABLE ?= no # Unicode +BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID +AUDIO_ENABLE ?= no # Audio output on port C6 |