Add support for Clueboard 66% rev4

8 files changed, 1465 insertions, 0 deletions

diff --git a/keyboards/clueboard/66/rev4/chconf.h b/keyboards/clueboard/66/rev4/chconf.h
new file mode 100644
index 000000000..1d9f12ff1
--- /dev/null
+++ b/keyboards/clueboard/66/rev4/chconf.h
@@ -0,0 +1,520 @@
+/*
+    ChibiOS - Copyright (C) 2006..2016 Giovanni Di Sirio
+
+    Licensed under the Apache License, Version 2.0 (the "License");
+    you may not use this file except in compliance with the License.
+    You may obtain a copy of the License at
+
+        http://www.apache.org/licenses/LICENSE-2.0
+
+    Unless required by applicable law or agreed to in writing, software
+    distributed under the License is distributed on an "AS IS" BASIS,
+    WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+    See the License for the specific language governing permissions and
+    limitations under the License.
+*/
+
+/**
+ * @file    templates/chconf.h
+ * @brief   Configuration file template.
+ * @details A copy of this file must be placed in each project directory, it
+ *          contains the application specific kernel settings.
+ *
+ * @addtogroup config
+ * @details Kernel related settings and hooks.
+ * @{
+ */
+
+#ifndef CHCONF_H
+#define CHCONF_H
+
+#define _CHIBIOS_RT_CONF_
+
+/*===========================================================================*/
+/**
+ * @name System timers settings
+ * @{
+ */
+/*===========================================================================*/
+
+/**
+ * @brief   System time counter resolution.
+ * @note    Allowed values are 16 or 32 bits.
+ */
+#define CH_CFG_ST_RESOLUTION                32
+
+/**
+ * @brief   System tick frequency.
+ * @details Frequency of the system timer that drives the system ticks. This
+ *          setting also defines the system tick time unit.
+ */
+#define CH_CFG_ST_FREQUENCY                 100000
+
+/**
+ * @brief   Time delta constant for the tick-less mode.
+ * @note    If this value is zero then the system uses the classic
+ *          periodic tick. This value represents the minimum number
+ *          of ticks that is safe to specify in a timeout directive.
+ *          The value one is not valid, timeouts are rounded up to
+ *          this value.
+ */
+#define CH_CFG_ST_TIMEDELTA                 2
+
+/** @} */
+
+/*===========================================================================*/
+/**
+ * @name Kernel parameters and options
+ * @{
+ */
+/*===========================================================================*/
+
+/**
+ * @brief   Round robin interval.
+ * @details This constant is the number of system ticks allowed for the
+ *          threads before preemption occurs. Setting this value to zero
+ *          disables the preemption for threads with equal priority and the
+ *          round robin becomes cooperative. Note that higher priority
+ *          threads can still preempt, the kernel is always preemptive.
+ * @note    Disabling the round robin preemption makes the kernel more compact
+ *          and generally faster.
+ * @note    The round robin preemption is not supported in tickless mode and
+ *          must be set to zero in that case.
+ */
+#define CH_CFG_TIME_QUANTUM                 0
+
+/**
+ * @brief   Managed RAM size.
+ * @details Size of the RAM area to be managed by the OS. If set to zero
+ *          then the whole available RAM is used. The core memory is made
+ *          available to the heap allocator and/or can be used directly through
+ *          the simplified core memory allocator.
+ *
+ * @note    In order to let the OS manage the whole RAM the linker script must
+ *          provide the @p __heap_base__ and @p __heap_end__ symbols.
+ * @note    Requires @p CH_CFG_USE_MEMCORE.
+ */
+#define CH_CFG_MEMCORE_SIZE                 0
+
+/**
+ * @brief   Idle thread automatic spawn suppression.
+ * @details When this option is activated the function @p chSysInit()
+ *          does not spawn the idle thread. The application @p main()
+ *          function becomes the idle thread and must implement an
+ *          infinite loop.
+ */
+#define CH_CFG_NO_IDLE_THREAD               FALSE
+
+/** @} */
+
+/*===========================================================================*/
+/**
+ * @name Performance options
+ * @{
+ */
+/*===========================================================================*/
+
+/**
+ * @brief   OS optimization.
+ * @details If enabled then time efficient rather than space efficient code
+ *          is used when two possible implementations exist.
+ *
+ * @note    This is not related to the compiler optimization options.
+ * @note    The default is @p TRUE.
+ */
+#define CH_CFG_OPTIMIZE_SPEED               TRUE
+
+/** @} */
+
+/*===========================================================================*/
+/**
+ * @name Subsystem options
+ * @{
+ */
+/*===========================================================================*/
+
+/**
+ * @brief   Time Measurement APIs.
+ * @details If enabled then the time measurement APIs are included in
+ *          the kernel.
+ *
+ * @note    The default is @p TRUE.
+ */
+#define CH_CFG_USE_TM                       TRUE
+
+/**
+ * @brief   Threads registry APIs.
+ * @details If enabled then the registry APIs are included in the kernel.
+ *
+ * @note    The default is @p TRUE.
+ */
+#define CH_CFG_USE_REGISTRY                 TRUE
+
+/**
+ * @brief   Threads synchronization APIs.
+ * @details If enabled then the @p chThdWait() function is included in
+ *          the kernel.
+ *
+ * @note    The default is @p TRUE.
+ */
+#define CH_CFG_USE_WAITEXIT                 TRUE
+
+/**
+ * @brief   Semaphores APIs.
+ * @details If enabled then the Semaphores APIs are included in the kernel.
+ *
+ * @note    The default is @p TRUE.
+ */
+#define CH_CFG_USE_SEMAPHORES               TRUE
+
+/**
+ * @brief   Semaphores queuing mode.
+ * @details If enabled then the threads are enqueued on semaphores by
+ *          priority rather than in FIFO order.
+ *
+ * @note    The default is @p FALSE. Enable this if you have special
+ *          requirements.
+ * @note    Requires @p CH_CFG_USE_SEMAPHORES.
+ */
+#define CH_CFG_USE_SEMAPHORES_PRIORITY      FALSE
+
+/**
+ * @brief   Mutexes APIs.
+ * @details If enabled then the mutexes APIs are included in the kernel.
+ *
+ * @note    The default is @p TRUE.
+ */
+#define CH_CFG_USE_MUTEXES                  TRUE
+
+/**
+ * @brief   Enables recursive behavior on mutexes.
+ * @note    Recursive mutexes are heavier and have an increased
+ *          memory footprint.
+ *
+ * @note    The default is @p FALSE.
+ * @note    Requires @p CH_CFG_USE_MUTEXES.
+ */
+#define CH_CFG_USE_MUTEXES_RECURSIVE        FALSE
+
+/**
+ * @brief   Conditional Variables APIs.
+ * @details If enabled then the conditional variables APIs are included
+ *          in the kernel.
+ *
+ * @note    The default is @p TRUE.
+ * @note    Requires @p CH_CFG_USE_MUTEXES.
+ */
+#define CH_CFG_USE_CONDVARS                 TRUE
+
+/**
+ * @brief   Conditional Variables APIs with timeout.
+ * @details If enabled then the conditional variables APIs with timeout
+ *          specification are included in the kernel.
+ *
+ * @note    The default is @p TRUE.
+ * @note    Requires @p CH_CFG_USE_CONDVARS.
+ */
+#define CH_CFG_USE_CONDVARS_TIMEOUT         TRUE
+
+/**
+ * @brief   Events Flags APIs.
+ * @details If enabled then the event flags APIs are included in the kernel.
+ *
+ * @note    The default is @p TRUE.
+ */
+#define CH_CFG_USE_EVENTS                   TRUE
+
+/**
+ * @brief   Events Flags APIs with timeout.
+ * @details If enabled then the events APIs with timeout specification
+ *          are included in the kernel.
+ *
+ * @note    The default is @p TRUE.
+ * @note    Requires @p CH_CFG_USE_EVENTS.
+ */
+#define CH_CFG_USE_EVENTS_TIMEOUT           TRUE
+
+/**
+ * @brief   Synchronous Messages APIs.
+ * @details If enabled then the synchronous messages APIs are included
+ *          in the kernel.
+ *
+ * @note    The default is @p TRUE.
+ */
+#define CH_CFG_USE_MESSAGES                 TRUE
+
+/**
+ * @brief   Synchronous Messages queuing mode.
+ * @details If enabled then messages are served by priority rather than in
+ *          FIFO order.
+ *
+ * @note    The default is @p FALSE. Enable this if you have special
+ *          requirements.
+ * @note    Requires @p CH_CFG_USE_MESSAGES.
+ */
+#define CH_CFG_USE_MESSAGES_PRIORITY        TRUE
+
+/**
+ * @brief   Mailboxes APIs.
+ * @details If enabled then the asynchronous messages (mailboxes) APIs are
+ *          included in the kernel.
+ *
+ * @note    The default is @p TRUE.
+ * @note    Requires @p CH_CFG_USE_SEMAPHORES.
+ */
+#define CH_CFG_USE_MAILBOXES                TRUE
+
+/**
+ * @brief   Core Memory Manager APIs.
+ * @details If enabled then the core memory manager APIs are included
+ *          in the kernel.
+ *
+ * @note    The default is @p TRUE.
+ */
+#define CH_CFG_USE_MEMCORE                  TRUE
+
+/**
+ * @brief   Heap Allocator APIs.
+ * @details If enabled then the memory heap allocator APIs are included
+ *          in the kernel.
+ *
+ * @note    The default is @p TRUE.
+ * @note    Requires @p CH_CFG_USE_MEMCORE and either @p CH_CFG_USE_MUTEXES or
+ *          @p CH_CFG_USE_SEMAPHORES.
+ * @note    Mutexes are recommended.
+ */
+#define CH_CFG_USE_HEAP                     TRUE
+
+/**
+ * @brief   Memory Pools Allocator APIs.
+ * @details If enabled then the memory pools allocator APIs are included
+ *          in the kernel.
+ *
+ * @note    The default is @p TRUE.
+ */
+#define CH_CFG_USE_MEMPOOLS                 TRUE
+
+/**
+ * @brief   Dynamic Threads APIs.
+ * @details If enabled then the dynamic threads creation APIs are included
+ *          in the kernel.
+ *
+ * @note    The default is @p TRUE.
+ * @note    Requires @p CH_CFG_USE_WAITEXIT.
+ * @note    Requires @p CH_CFG_USE_HEAP and/or @p CH_CFG_USE_MEMPOOLS.
+ */
+#define CH_CFG_USE_DYNAMIC                  TRUE
+
+/** @} */
+
+/*===========================================================================*/
+/**
+ * @name Debug options
+ * @{
+ */
+/*===========================================================================*/
+
+/**
+ * @brief   Debug option, kernel statistics.
+ *
+ * @note    The default is @p FALSE.
+ */
+#define CH_DBG_STATISTICS                   FALSE
+
+/**
+ * @brief   Debug option, system state check.
+ * @details If enabled the correct call protocol for system APIs is checked
+ *          at runtime.
+ *
+ * @note    The default is @p FALSE.
+ */
+#define CH_DBG_SYSTEM_STATE_CHECK           FALSE
+
+/**
+ * @brief   Debug option, parameters checks.
+ * @details If enabled then the checks on the API functions input
+ *          parameters are activated.
+ *
+ * @note    The default is @p FALSE.
+ */
+#define CH_DBG_ENABLE_CHECKS                FALSE
+
+/**
+ * @brief   Debug option, consistency checks.
+ * @details If enabled then all the assertions in the kernel code are
+ *          activated. This includes consistency checks inside the kernel,
+ *          runtime anomalies and port-defined checks.
+ *
+ * @note    The default is @p FALSE.
+ */
+#define CH_DBG_ENABLE_ASSERTS               FALSE
+
+/**
+ * @brief   Debug option, trace buffer.
+ * @details If enabled then the trace buffer is activated.
+ *
+ * @note    The default is @p CH_DBG_TRACE_MASK_DISABLED.
+ */
+#define CH_DBG_TRACE_MASK                   CH_DBG_TRACE_MASK_DISABLED
+
+/**
+ * @brief   Trace buffer entries.
+ * @note    The trace buffer is only allocated if @p CH_DBG_TRACE_MASK is
+ *          different from @p CH_DBG_TRACE_MASK_DISABLED.
+ */
+#define CH_DBG_TRACE_BUFFER_SIZE            128
+
+/**
+ * @brief   Debug option, stack checks.
+ * @details If enabled then a runtime stack check is performed.
+ *
+ * @note    The default is @p FALSE.
+ * @note    The stack check is performed in a architecture/port dependent way.
+ *          It may not be implemented or some ports.
+ * @note    The default failure mode is to halt the system with the global
+ *          @p panic_msg variable set to @p NULL.
+ */
+#define CH_DBG_ENABLE_STACK_CHECK           TRUE
+
+/**
+ * @brief   Debug option, stacks initialization.
+ * @details If enabled then the threads working area is filled with a byte
+ *          value when a thread is created. This can be useful for the
+ *          runtime measurement of the used stack.
+ *
+ * @note    The default is @p FALSE.
+ */
+#define CH_DBG_FILL_THREADS                 FALSE
+
+/**
+ * @brief   Debug option, threads profiling.
+ * @details If enabled then a field is added to the @p thread_t structure that
+ *          counts the system ticks occurred while executing the thread.
+ *
+ * @note    The default is @p FALSE.
+ * @note    This debug option is not currently compatible with the
+ *          tickless mode.
+ */
+#define CH_DBG_THREADS_PROFILING            FALSE
+
+/** @} */
+
+/*===========================================================================*/
+/**
+ * @name Kernel hooks
+ * @{
+ */
+/*===========================================================================*/
+
+/**
+ * @brief   Threads descriptor structure extension.
+ * @details User fields added to the end of the @p thread_t structure.
+ */
+#define CH_CFG_THREAD_EXTRA_FIELDS                                          \
+  /* Add threads custom fields here.*/
+
+/**
+ * @brief   Threads initialization hook.
+ * @details User initialization code added to the @p chThdInit() API.
+ *
+ * @note    It is invoked from within @p chThdInit() and implicitly from all
+ *          the threads creation APIs.
+ */
+#define CH_CFG_THREAD_INIT_HOOK(tp) {                                       \
+  /* Add threads initialization code here.*/                                \
+}
+
+/**
+ * @brief   Threads finalization hook.
+ * @details User finalization code added to the @p chThdExit() API.
+ */
+#define CH_CFG_THREAD_EXIT_HOOK(tp) {                                       \
+  /* Add threads finalization code here.*/                                  \
+}
+
+/**
+ * @brief   Context switch hook.
+ * @details This hook is invoked just before switching between threads.
+ */
+#define CH_CFG_CONTEXT_SWITCH_HOOK(ntp, otp) {                              \
+  /* Context switch code here.*/                                            \
+}
+
+/**
+ * @brief   ISR enter hook.
+ */
+#define CH_CFG_IRQ_PROLOGUE_HOOK() {                                        \
+  /* IRQ prologue code here.*/                                              \
+}
+
+/**
+ * @brief   ISR exit hook.
+ */
+#define CH_CFG_IRQ_EPILOGUE_HOOK() {                                        \
+  /* IRQ epilogue code here.*/                                              \
+}
+
+/**
+ * @brief   Idle thread enter hook.
+ * @note    This hook is invoked within a critical zone, no OS functions
+ *          should be invoked from here.
+ * @note    This macro can be used to activate a power saving mode.
+ */
+#define CH_CFG_IDLE_ENTER_HOOK() {                                          \
+  /* Idle-enter code here.*/                                                \
+}
+
+/**
+ * @brief   Idle thread leave hook.
+ * @note    This hook is invoked within a critical zone, no OS functions
+ *          should be invoked from here.
+ * @note    This macro can be used to deactivate a power saving mode.
+ */
+#define CH_CFG_IDLE_LEAVE_HOOK() {                                          \
+  /* Idle-leave code here.*/                                                \
+}
+
+/**
+ * @brief   Idle Loop hook.
+ * @details This hook is continuously invoked by the idle thread loop.
+ */
+#define CH_CFG_IDLE_LOOP_HOOK() {                                           \
+  /* Idle loop code here.*/                                                 \
+}
+
+/**
+ * @brief   System tick event hook.
+ * @details This hook is invoked in the system tick handler immediately
+ *          after processing the virtual timers queue.
+ */
+#define CH_CFG_SYSTEM_TICK_HOOK() {                                         \
+  /* System tick event code here.*/                                         \
+}
+
+/**
+ * @brief   System halt hook.
+ * @details This hook is invoked in case to a system halting error before
+ *          the system is halted.
+ */
+#define CH_CFG_SYSTEM_HALT_HOOK(reason) {                                   \
+  /* System halt code here.*/                                               \
+}
+
+/**
+ * @brief   Trace hook.
+ * @details This hook is invoked each time a new record is written in the
+ *          trace buffer.
+ */
+#define CH_CFG_TRACE_HOOK(tep) {                                            \
+  /* Trace code here.*/                                                     \
+}
+
+/** @} */
+
+/*===========================================================================*/
+/* Port-specific settings (override port settings defaulted in chcore.h).    */
+/*===========================================================================*/
+
+#endif  /* CHCONF_H */
+
+/** @} */
diff --git a/keyboards/clueboard/66/rev4/config.h b/keyboards/clueboard/66/rev4/config.h
new file mode 100644
index 000000000..19a9837a3
--- /dev/null
+++ b/keyboards/clueboard/66/rev4/config.h
@@ -0,0 +1,83 @@
+#pragma once
+
+#include "config_common.h"
+
+/* USB Device descriptor parameter */
+#define VENDOR_ID       0xC1ED
+#define PRODUCT_ID      0x2390
+#define DEVICE_VER      0x0001
+#define MANUFACTURER    Clueboard
+#define PRODUCT         Clueboard 66% rev4
+#define DESCRIPTION     QMK keyboard firmware for Clueboard
+
+/* Address for jumping to bootloader on STM32 chips. */
+/* It is chip dependent, the correct number can be looked up here:
+ * http://www.st.com/web/en/resource/technical/document/application_note/CD00167594.pdf
+ */
+#define STM32_BOOTLOADER_ADDRESS 0x1FFFD800
+
+/* key matrix size */
+#define MATRIX_ROWS 10
+#define MATRIX_COLS 8
+
+/* ROWS: Top to bottom, COLS: Left to right
+*/
+#define MATRIX_ROW_PINS { B11, A6, A3, A2, A1, B7, B6, C15, C14, C13 }
+#define MATRIX_COL_PINS { B10, B2, B1, B0, A7, B4, B3, B5 }
+#define UNUSED_PINS { B15, B14, B13, B12, B9, B8, A15, A10, A9, A8 }
+
+/* COL2ROW or ROW2COL */
+#define DIODE_DIRECTION COL2ROW
+
+/* Set 0 if debouncing isn't needed */
+#define DEBOUNCING_DELAY 5
+
+/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
+#define LOCKING_SUPPORT_ENABLE
+/* Locking resynchronize hack */
+#define LOCKING_RESYNC_ENABLE
+
+/* key combination for command */
+#define IS_COMMAND() ( \
+    keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \
+)
+
+/*
+ * Feature disable options
+ *  These options are also useful to firmware size reduction.
+ */
+
+/* disable debug print */
+//#define NO_DEBUG
+
+/* disable print */
+//#define NO_PRINT
+
+/* disable action features */
+//#define NO_ACTION_LAYER
+//#define NO_ACTION_TAPPING
+//#define NO_ACTION_ONESHOT
+//#define NO_ACTION_MACRO
+//#define NO_ACTION_FUNCTION
+
+ /* Backlight configuration
+ */
+#define BACKLIGHT_LEVELS 1
+
+/* Underlight configuration
+ */
+#define RGB_DI_PIN D7
+#define RGBLED_NUM 18     // Number of LEDs
+#define RGBLIGHT_HUE_STEP 32
+#define RGBLIGHT_SAT_STEP 17
+#define RGBLIGHT_VAL_STEP 17
+
+#define RGBLIGHT_ANIMATIONS
+#define RGBLIGHT_EFFECT_BREATHE_CENTER 1
+#define RGBLIGHT_EFFECT_BREATHE_MAX 200
+#define RGBLIGHT_EFFECT_CHRISTMAS_INTERVAL 666*2
+#define RGBLIGHT_EFFECT_CHRISTMAS_STEP 1
+#define RGBLIGHT_EFFECT_KNIGHT_LENGTH 3   // How many LEDs wide to light up
+#define RGBLIGHT_EFFECT_KNIGHT_OFFSET 2   // The led to start at
+#define RGBLIGHT_EFFECT_KNIGHT_LED_NUM 5  // How many LEDs to travel
+#define RGBLIGHT_EFFECT_SNAKE_LENGTH 4    // How many LEDs wide to light up
diff --git a/keyboards/clueboard/66/rev4/halconf.h b/keyboards/clueboard/66/rev4/halconf.h
new file mode 100644
index 000000000..e617fdffc
--- /dev/null
+++ b/keyboards/clueboard/66/rev4/halconf.h
@@ -0,0 +1,388 @@
+/*
+    ChibiOS - Copyright (C) 2006..2016 Giovanni Di Sirio
+
+    Licensed under the Apache License, Version 2.0 (the "License");
+    you may not use this file except in compliance with the License.
+    You may obtain a copy of the License at
+
+        http://www.apache.org/licenses/LICENSE-2.0
+
+    Unless required by applicable law or agreed to in writing, software
+    distributed under the License is distributed on an "AS IS" BASIS,
+    WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+    See the License for the specific language governing permissions and
+    limitations under the License.
+*/
+
+/**
+ * @file    templates/halconf.h
+ * @brief   HAL configuration header.
+ * @details HAL configuration file, this file allows to enable or disable the
+ *          various device drivers from your application. You may also use
+ *          this file in order to override the device drivers default settings.
+ *
+ * @addtogroup HAL_CONF
+ * @{
+ */
+
+#ifndef HALCONF_H
+#define HALCONF_H
+
+#include "mcuconf.h"
+
+/**
+ * @brief   Enables the PAL subsystem.
+ */
+#if !defined(HAL_USE_PAL) || defined(__DOXYGEN__)
+#define HAL_USE_PAL                 TRUE
+#endif
+
+/**
+ * @brief   Enables the ADC subsystem.
+ */
+#if !defined(HAL_USE_ADC) || defined(__DOXYGEN__)
+#define HAL_USE_ADC                 FALSE
+#endif
+
+/**
+ * @brief   Enables the CAN subsystem.
+ */
+#if !defined(HAL_USE_CAN) || defined(__DOXYGEN__)
+#define HAL_USE_CAN                 FALSE
+#endif
+
+/**
+ * @brief   Enables the DAC subsystem.
+ */
+#if !defined(HAL_USE_DAC) || defined(__DOXYGEN__)
+#define HAL_USE_DAC                 TRUE
+#endif
+
+/**
+ * @brief   Enables the EXT subsystem.
+ */
+#if !defined(HAL_USE_EXT) || defined(__DOXYGEN__)
+#define HAL_USE_EXT                 FALSE
+#endif
+
+/**
+ * @brief   Enables the GPT subsystem.
+ */
+#if !defined(HAL_USE_GPT) || defined(__DOXYGEN__)
+#define HAL_USE_GPT                 TRUE
+#endif
+
+/**
+ * @brief   Enables the I2C subsystem.
+ */
+#if !defined(HAL_USE_I2C) || defined(__DOXYGEN__)
+#define HAL_USE_I2C                 FALSE
+#endif
+
+/**
+ * @brief   Enables the I2S subsystem.
+ */
+#if !defined(HAL_USE_I2S) || defined(__DOXYGEN__)
+#define HAL_USE_I2S                 FALSE
+#endif
+
+/**
+ * @brief   Enables the ICU subsystem.
+ */
+#if !defined(HAL_USE_ICU) || defined(__DOXYGEN__)
+#define HAL_USE_ICU                 FALSE
+#endif
+
+/**
+ * @brief   Enables the MAC subsystem.
+ */
+#if !defined(HAL_USE_MAC) || defined(__DOXYGEN__)
+#define HAL_USE_MAC                 FALSE
+#endif
+
+/**
+ * @brief   Enables the MMC_SPI subsystem.
+ */
+#if !defined(HAL_USE_MMC_SPI) || defined(__DOXYGEN__)
+#define HAL_USE_MMC_SPI             FALSE
+#endif
+
+/**
+ * @brief   Enables the PWM subsystem.
+ */
+#if !defined(HAL_USE_PWM) || defined(__DOXYGEN__)
+#define HAL_USE_PWM                 FALSE
+#endif
+
+/**
+ * @brief   Enables the QSPI subsystem.
+ */
+#if !defined(HAL_USE_QSPI) || defined(__DOXYGEN__)
+#define HAL_USE_QSPI                FALSE
+#endif
+
+/**
+ * @brief   Enables the RTC subsystem.
+ */
+#if !defined(HAL_USE_RTC) || defined(__DOXYGEN__)
+#define HAL_USE_RTC                 FALSE
+#endif
+
+/**
+ * @brief   Enables the SDC subsystem.
+ */
+#if !defined(HAL_USE_SDC) || defined(__DOXYGEN__)
+#define HAL_USE_SDC                 FALSE
+#endif
+
+/**
+ * @brief   Enables the SERIAL subsystem.
+ */
+#if !defined(HAL_USE_SERIAL) || defined(__DOXYGEN__)
+#define HAL_USE_SERIAL              FALSE
+#endif
+
+/**
+ * @brief   Enables the SERIAL over USB subsystem.
+ */
+#if !defined(HAL_USE_SERIAL_USB) || defined(__DOXYGEN__)
+#define HAL_USE_SERIAL_USB          FALSE
+#endif
+
+/**
+ * @brief   Enables the SPI subsystem.
+ */
+#if !defined(HAL_USE_SPI) || defined(__DOXYGEN__)
+#define HAL_USE_SPI                 FALSE
+#endif
+
+/**
+ * @brief   Enables the UART subsystem.
+ */
+#if !defined(HAL_USE_UART) || defined(__DOXYGEN__)
+#define HAL_USE_UART                FALSE
+#endif
+
+/**
+ * @brief   Enables the USB subsystem.
+ */
+#if !defined(HAL_USE_USB) || defined(__DOXYGEN__)
+#define HAL_USE_USB                 TRUE
+#endif
+
+/**
+ * @brief   Enables the WDG subsystem.
+ */
+#if !defined(HAL_USE_WDG) || defined(__DOXYGEN__)
+#define HAL_USE_WDG                 FALSE
+#endif
+
+/*===========================================================================*/
+/* ADC driver related settings.                                              */
+/*===========================================================================*/
+
+/**
+ * @brief   Enables synchronous APIs.
+ * @note    Disabling this option saves both code and data space.
+ */
+#if !defined(ADC_USE_WAIT) || defined(__DOXYGEN__)
+#define ADC_USE_WAIT                TRUE
+#endif
+
+/**
+ * @brief   Enables the @p adcAcquireBus() and @p adcReleaseBus() APIs.
+ * @note    Disabling this option saves both code and data space.
+ */
+#if !defined(ADC_USE_MUTUAL_EXCLUSION) || defined(__DOXYGEN__)
+#define ADC_USE_MUTUAL_EXCLUSION    TRUE
+#endif
+
+/*===========================================================================*/
+/* CAN driver related settings.                                              */
+/*===========================================================================*/
+
+/**
+ * @brief   Sleep mode related APIs inclusion switch.
+ */
+#if !defined(CAN_USE_SLEEP_MODE) || defined(__DOXYGEN__)
+#define CAN_USE_SLEEP_MODE          TRUE
+#endif
+
+/*===========================================================================*/
+/* I2C driver related settings.                                              */
+/*===========================================================================*/
+
+/**
+ * @brief   Enables the mutual exclusion APIs on the I2C bus.
+ */
+#if !defined(I2C_USE_MUTUAL_EXCLUSION) || defined(__DOXYGEN__)
+#define I2C_USE_MUTUAL_EXCLUSION    TRUE
+#endif
+
+/*===========================================================================*/
+/* MAC driver related settings.                                              */
+/*===========================================================================*/
+
+/**
+ * @brief   Enables an event sources for incoming packets.
+ */
+#if !defined(MAC_USE_ZERO_COPY) || defined(__DOXYGEN__)
+#define MAC_USE_ZERO_COPY           FALSE
+#endif
+
+/**
+ * @brief   Enables an event sources for incoming packets.
+ */
+#if !defined(MAC_USE_EVENTS) || defined(__DOXYGEN__)
+#define MAC_USE_EVENTS              TRUE
+#endif
+
+/*===========================================================================*/
+/* MMC_SPI driver related settings.                                          */
+/*===========================================================================*/
+
+/**
+ * @brief   Delays insertions.
+ * @details If enabled this options inserts delays into the MMC waiting
+ *          routines releasing some extra CPU time for the threads with
+ *          lower priority, this may slow down the driver a bit however.
+ *          This option is recommended also if the SPI driver does not
+ *          use a DMA channel and heavily loads the CPU.
+ */
+#if !defined(MMC_NICE_WAITING) || defined(__DOXYGEN__)
+#define MMC_NICE_WAITING            TRUE
+#endif
+
+/*===========================================================================*/
+/* SDC driver related settings.                                              */
+/*===========================================================================*/
+
+/**
+ * @brief   Number of initialization attempts before rejecting the card.
+ * @note    Attempts are performed at 10mS intervals.
+ */
+#if !defined(SDC_INIT_RETRY) || defined(__DOXYGEN__)
+#define SDC_INIT_RETRY              100
+#endif
+
+/**
+ * @brief   Include support for MMC cards.
+ * @note    MMC support is not yet implemented so this option must be kept
+ *          at @p FALSE.
+ */
+#if !defined(SDC_MMC_SUPPORT) || defined(__DOXYGEN__)
+#define SDC_MMC_SUPPORT             FALSE
+#endif
+
+/**
+ * @brief   Delays insertions.
+ * @details If enabled this options inserts delays into the MMC waiting
+ *          routines releasing some extra CPU time for the threads with
+ *          lower priority, this may slow down the driver a bit however.
+ */
+#if !defined(SDC_NICE_WAITING) || defined(__DOXYGEN__)
+#define SDC_NICE_WAITING            TRUE
+#endif
+
+/*===========================================================================*/
+/* SERIAL driver related settings.                                           */
+/*===========================================================================*/
+
+/**
+ * @brief   Default bit rate.
+ * @details Configuration parameter, this is the baud rate selected for the
+ *          default configuration.
+ */
+#if !defined(SERIAL_DEFAULT_BITRATE) || defined(__DOXYGEN__)
+#define SERIAL_DEFAULT_BITRATE      38400
+#endif
+
+/**
+ * @brief   Serial buffers size.
+ * @details Configuration parameter, you can change the depth of the queue
+ *          buffers depending on the requirements of your application.
+ * @note    The default is 16 bytes for both the transmission and receive
+ *          buffers.
+ */
+#if !defined(SERIAL_BUFFERS_SIZE) || defined(__DOXYGEN__)
+#define SERIAL_BUFFERS_SIZE         16
+#endif
+
+/*===========================================================================*/
+/* SERIAL_USB driver related setting.                                        */
+/*===========================================================================*/
+
+/**
+ * @brief   Serial over USB buffers size.
+ * @details Configuration parameter, the buffer size must be a multiple of
+ *          the USB data endpoint maximum packet size.
+ * @note    The default is 256 bytes for both the transmission and receive
+ *          buffers.
+ */
+#if !defined(SERIAL_USB_BUFFERS_SIZE) || defined(__DOXYGEN__)
+#define SERIAL_USB_BUFFERS_SIZE     1
+#endif
+
+/**
+ * @brief   Serial over USB number of buffers.
+ * @note    The default is 2 buffers.
+ */
+#if !defined(SERIAL_USB_BUFFERS_NUMBER) || defined(__DOXYGEN__)
+#define SERIAL_USB_BUFFERS_NUMBER   2
+#endif
+
+/*===========================================================================*/
+/* SPI driver related settings.                                              */
+/*===========================================================================*/
+
+/**
+ * @brief   Enables synchronous APIs.
+ * @note    Disabling this option saves both code and data space.
+ */
+#if !defined(SPI_USE_WAIT) || defined(__DOXYGEN__)
+#define SPI_USE_WAIT                TRUE
+#endif
+
+/**
+ * @brief   Enables the @p spiAcquireBus() and @p spiReleaseBus() APIs.
+ * @note    Disabling this option saves both code and data space.
+ */
+#if !defined(SPI_USE_MUTUAL_EXCLUSION) || defined(__DOXYGEN__)
+#define SPI_USE_MUTUAL_EXCLUSION    TRUE
+#endif
+
+/*===========================================================================*/
+/* UART driver related settings.                                             */
+/*===========================================================================*/
+
+/**
+ * @brief   Enables synchronous APIs.
+ * @note    Disabling this option saves both code and data space.
+ */
+#if !defined(UART_USE_WAIT) || defined(__DOXYGEN__)
+#define UART_USE_WAIT               FALSE
+#endif
+
+/**
+ * @brief   Enables the @p uartAcquireBus() and @p uartReleaseBus() APIs.
+ * @note    Disabling this option saves both code and data space.
+ */
+#if !defined(UART_USE_MUTUAL_EXCLUSION) || defined(__DOXYGEN__)
+#define UART_USE_MUTUAL_EXCLUSION   FALSE
+#endif
+
+/*===========================================================================*/
+/* USB driver related settings.                                              */
+/*===========================================================================*/
+
+/**
+ * @brief   Enables synchronous APIs.
+ * @note    Disabling this option saves both code and data space.
+ */
+#if !defined(USB_USE_WAIT) || defined(__DOXYGEN__)
+#define USB_USE_WAIT                TRUE
+#endif
+
+#endif /* HALCONF_H */
+
+/** @} */
diff --git a/keyboards/clueboard/66/rev4/mcuconf.h b/keyboards/clueboard/66/rev4/mcuconf.h
new file mode 100644
index 000000000..94cb540ec
--- /dev/null
+++ b/keyboards/clueboard/66/rev4/mcuconf.h
@@ -0,0 +1,257 @@
+/*
+    ChibiOS - Copyright (C) 2006..2016 Giovanni Di Sirio
+
+    Licensed under the Apache License, Version 2.0 (the "License");
+    you may not use this file except in compliance with the License.
+    You may obtain a copy of the License at
+
+        http://www.apache.org/licenses/LICENSE-2.0
+
+    Unless required by applicable law or agreed to in writing, software
+    distributed under the License is distributed on an "AS IS" BASIS,
+    WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+    See the License for the specific language governing permissions and
+    limitations under the License.
+*/
+
+#ifndef MCUCONF_H
+#define MCUCONF_H
+
+/*
+ * STM32F3xx drivers configuration.
+ * The following settings override the default settings present in
+ * the various device driver implementation headers.
+ * Note that the settings for each driver only have effect if the whole
+ * driver is enabled in halconf.h.
+ *
+ * IRQ priorities:
+ * 15...0       Lowest...Highest.
+ *
+ * DMA priorities:
+ * 0...3        Lowest...Highest.
+ */
+
+#define STM32F3xx_MCUCONF
+
+/*
+ * HAL driver system settings.
+ */
+#define STM32_NO_INIT                       FALSE
+#define STM32_PVD_ENABLE                    FALSE
+#define STM32_PLS                           STM32_PLS_LEV0
+#define STM32_HSI_ENABLED                   TRUE
+#define STM32_LSI_ENABLED                   TRUE
+#define STM32_HSE_ENABLED                   TRUE
+#define STM32_LSE_ENABLED                   FALSE
+#define STM32_SW                            STM32_SW_PLL
+#define STM32_PLLSRC                        STM32_PLLSRC_HSE
+#define STM32_PREDIV_VALUE                  1
+#define STM32_PLLMUL_VALUE                  9
+#define STM32_HPRE                          STM32_HPRE_DIV1
+#define STM32_PPRE1                         STM32_PPRE1_DIV2
+#define STM32_PPRE2                         STM32_PPRE2_DIV2
+#define STM32_MCOSEL                        STM32_MCOSEL_NOCLOCK
+#define STM32_ADC12PRES                     STM32_ADC12PRES_DIV1
+#define STM32_ADC34PRES                     STM32_ADC34PRES_DIV1
+#define STM32_USART1SW                      STM32_USART1SW_PCLK
+#define STM32_USART2SW                      STM32_USART2SW_PCLK
+#define STM32_USART3SW                      STM32_USART3SW_PCLK
+#define STM32_UART4SW                       STM32_UART4SW_PCLK
+#define STM32_UART5SW                       STM32_UART5SW_PCLK
+#define STM32_I2C1SW                        STM32_I2C1SW_SYSCLK
+#define STM32_I2C2SW                        STM32_I2C2SW_SYSCLK
+#define STM32_TIM1SW                        STM32_TIM1SW_PCLK2
+#define STM32_TIM8SW                        STM32_TIM8SW_PCLK2
+#define STM32_RTCSEL                        STM32_RTCSEL_LSI
+#define STM32_USB_CLOCK_REQUIRED            TRUE
+#define STM32_USBPRE                        STM32_USBPRE_DIV1P5
+
+#undef STM32_HSE_BYPASS
+// #error "oh no"
+// #endif
+
+/*
+ * ADC driver system settings.
+ */
+#define STM32_ADC_DUAL_MODE                 FALSE
+#define STM32_ADC_COMPACT_SAMPLES           FALSE
+#define STM32_ADC_USE_ADC1                  FALSE
+#define STM32_ADC_USE_ADC2                  FALSE
+#define STM32_ADC_USE_ADC3                  FALSE
+#define STM32_ADC_USE_ADC4                  FALSE
+#define STM32_ADC_ADC1_DMA_STREAM           STM32_DMA_STREAM_ID(1, 1)
+#define STM32_ADC_ADC2_DMA_STREAM           STM32_DMA_STREAM_ID(2, 1)
+#define STM32_ADC_ADC3_DMA_STREAM           STM32_DMA_STREAM_ID(2, 5)
+#define STM32_ADC_ADC4_DMA_STREAM           STM32_DMA_STREAM_ID(2, 2)
+#define STM32_ADC_ADC1_DMA_PRIORITY         2
+#define STM32_ADC_ADC2_DMA_PRIORITY         2
+#define STM32_ADC_ADC3_DMA_PRIORITY         2
+#define STM32_ADC_ADC4_DMA_PRIORITY         2
+#define STM32_ADC_ADC12_IRQ_PRIORITY        5
+#define STM32_ADC_ADC3_IRQ_PRIORITY         5
+#define STM32_ADC_ADC4_IRQ_PRIORITY         5
+#define STM32_ADC_ADC1_DMA_IRQ_PRIORITY     5
+#define STM32_ADC_ADC2_DMA_IRQ_PRIORITY     5
+#define STM32_ADC_ADC3_DMA_IRQ_PRIORITY     5
+#define STM32_ADC_ADC4_DMA_IRQ_PRIORITY     5
+#define STM32_ADC_ADC12_CLOCK_MODE          ADC_CCR_CKMODE_AHB_DIV1
+#define STM32_ADC_ADC34_CLOCK_MODE          ADC_CCR_CKMODE_AHB_DIV1
+
+/*
+ * CAN driver system settings.
+ */
+#define STM32_CAN_USE_CAN1                  FALSE
+#define STM32_CAN_CAN1_IRQ_PRIORITY         11
+
+/*
+ * DAC driver system settings.
+ */
+#define STM32_DAC_DUAL_MODE                 FALSE
+#define STM32_DAC_USE_DAC1_CH1              TRUE
+#define STM32_DAC_USE_DAC1_CH2              TRUE
+#define STM32_DAC_DAC1_CH1_IRQ_PRIORITY     10
+#define STM32_DAC_DAC1_CH2_IRQ_PRIORITY     10
+#define STM32_DAC_DAC1_CH1_DMA_PRIORITY     2
+#define STM32_DAC_DAC1_CH2_DMA_PRIORITY     2
+
+/*
+ * EXT driver system settings.
+ */
+#define STM32_EXT_EXTI0_IRQ_PRIORITY        6
+#define STM32_EXT_EXTI1_IRQ_PRIORITY        6
+#define STM32_EXT_EXTI2_IRQ_PRIORITY        6
+#define STM32_EXT_EXTI3_IRQ_PRIORITY        6
+#define STM32_EXT_EXTI4_IRQ_PRIORITY        6
+#define STM32_EXT_EXTI5_9_IRQ_PRIORITY      6
+#define STM32_EXT_EXTI10_15_IRQ_PRIORITY    6
+#define STM32_EXT_EXTI16_IRQ_PRIORITY       6
+#define STM32_EXT_EXTI17_IRQ_PRIORITY       6
+#define STM32_EXT_EXTI18_IRQ_PRIORITY       6
+#define STM32_EXT_EXTI19_IRQ_PRIORITY       6
+#define STM32_EXT_EXTI20_IRQ_PRIORITY       6
+#define STM32_EXT_EXTI21_22_29_IRQ_PRIORITY 6
+#define STM32_EXT_EXTI30_32_IRQ_PRIORITY    6
+#define STM32_EXT_EXTI33_IRQ_PRIORITY       6
+
+/*
+ * GPT driver system settings.
+ */
+#define STM32_GPT_USE_TIM1                  FALSE
+#define STM32_GPT_USE_TIM2                  FALSE
+#define STM32_GPT_USE_TIM3                  FALSE
+#define STM32_GPT_USE_TIM4                  FALSE
+#define STM32_GPT_USE_TIM6                  TRUE
+#define STM32_GPT_USE_TIM7                  TRUE
+#define STM32_GPT_USE_TIM8                  TRUE
+#define STM32_GPT_TIM1_IRQ_PRIORITY         7
+#define STM32_GPT_TIM2_IRQ_PRIORITY         7
+#define STM32_GPT_TIM3_IRQ_PRIORITY         7
+#define STM32_GPT_TIM4_IRQ_PRIORITY         7
+#define STM32_GPT_TIM6_IRQ_PRIORITY         7
+#define STM32_GPT_TIM7_IRQ_PRIORITY         7
+#define STM32_GPT_TIM8_IRQ_PRIORITY         7
+
+/*
+ * I2C driver system settings.
+ */
+#define STM32_I2C_USE_I2C1                  FALSE
+#define STM32_I2C_USE_I2C2                  FALSE
+#define STM32_I2C_BUSY_TIMEOUT              50
+#define STM32_I2C_I2C1_IRQ_PRIORITY         10
+#define STM32_I2C_I2C2_IRQ_PRIORITY         10
+#define STM32_I2C_USE_DMA                   TRUE
+#define STM32_I2C_I2C1_DMA_PRIORITY         1
+#define STM32_I2C_I2C2_DMA_PRIORITY         1
+#define STM32_I2C_DMA_ERROR_HOOK(i2cp)      osalSysHalt("DMA failure")
+
+/*
+ * ICU driver system settings.
+ */
+#define STM32_ICU_USE_TIM1                  FALSE
+#define STM32_ICU_USE_TIM2                  FALSE
+#define STM32_ICU_USE_TIM3                  FALSE
+#define STM32_ICU_USE_TIM4                  FALSE
+#define STM32_ICU_USE_TIM8                  FALSE
+#define STM32_ICU_TIM1_IRQ_PRIORITY         7
+#define STM32_ICU_TIM2_IRQ_PRIORITY         7
+#define STM32_ICU_TIM3_IRQ_PRIORITY         7
+#define STM32_ICU_TIM4_IRQ_PRIORITY         7
+#define STM32_ICU_TIM8_IRQ_PRIORITY         7
+
+/*
+ * PWM driver system settings.
+ */
+#define STM32_PWM_USE_ADVANCED              FALSE
+#define STM32_PWM_USE_TIM1                  FALSE
+#define STM32_PWM_USE_TIM2                  FALSE
+#define STM32_PWM_USE_TIM3                  FALSE
+#define STM32_PWM_USE_TIM4                  FALSE
+#define STM32_PWM_USE_TIM8                  FALSE
+#define STM32_PWM_TIM1_IRQ_PRIORITY         7
+#define STM32_PWM_TIM2_IRQ_PRIORITY         7
+#define STM32_PWM_TIM3_IRQ_PRIORITY         7
+#define STM32_PWM_TIM4_IRQ_PRIORITY         7
+#define STM32_PWM_TIM8_IRQ_PRIORITY         7
+
+/*
+ * SERIAL driver system settings.
+ */
+#define STM32_SERIAL_USE_USART1             FALSE
+#define STM32_SERIAL_USE_USART2             FALSE
+#define STM32_SERIAL_USE_USART3             FALSE
+#define STM32_SERIAL_USE_UART4              FALSE
+#define STM32_SERIAL_USE_UART5              FALSE
+#define STM32_SERIAL_USART1_PRIORITY        12
+#define STM32_SERIAL_USART2_PRIORITY        12
+#define STM32_SERIAL_USART3_PRIORITY        12
+#define STM32_SERIAL_UART4_PRIORITY         12
+#define STM32_SERIAL_UART5_PRIORITY         12
+
+/*
+ * SPI driver system settings.
+ */
+#define STM32_SPI_USE_SPI1                  FALSE
+#define STM32_SPI_USE_SPI2                  FALSE
+#define STM32_SPI_USE_SPI3                  FALSE
+#define STM32_SPI_SPI1_DMA_PRIORITY         1
+#define STM32_SPI_SPI2_DMA_PRIORITY         1
+#define STM32_SPI_SPI3_DMA_PRIORITY         1
+#define STM32_SPI_SPI1_IRQ_PRIORITY         10
+#define STM32_SPI_SPI2_IRQ_PRIORITY         10
+#define STM32_SPI_SPI3_IRQ_PRIORITY         10
+#define STM32_SPI_DMA_ERROR_HOOK(spip)      osalSysHalt("DMA failure")
+
+/*
+ * ST driver system settings.
+ */
+#define STM32_ST_IRQ_PRIORITY               8
+#define STM32_ST_USE_TIMER                  2
+
+/*
+ * UART driver system settings.
+ */
+#define STM32_UART_USE_USART1               FALSE
+#define STM32_UART_USE_USART2               FALSE
+#define STM32_UART_USE_USART3               FALSE
+#define STM32_UART_USART1_IRQ_PRIORITY      12
+#define STM32_UART_USART2_IRQ_PRIORITY      12
+#define STM32_UART_USART3_IRQ_PRIORITY      12
+#define STM32_UART_USART1_DMA_PRIORITY      0
+#define STM32_UART_USART2_DMA_PRIORITY      0
+#define STM32_UART_USART3_DMA_PRIORITY      0
+#define STM32_UART_DMA_ERROR_HOOK(uartp)    osalSysHalt("DMA failure")
+
+/*
+ * USB driver system settings.
+ */
+#define STM32_USB_USE_USB1                  TRUE
+#define STM32_USB_LOW_POWER_ON_SUSPEND      FALSE
+#define STM32_USB_USB1_HP_IRQ_PRIORITY      13
+#define STM32_USB_USB1_LP_IRQ_PRIORITY      14
+
+/*
+ * WDG driver system settings.
+ */
+#define STM32_WDG_USE_IWDG                  FALSE
+
+#endif /* MCUCONF_H */
diff --git a/keyboards/clueboard/66/rev4/readme.md b/keyboards/clueboard/66/rev4/readme.md
new file mode 100644
index 000000000..ba0afff78
--- /dev/null
+++ b/keyboards/clueboard/66/rev4/readme.md
@@ -0,0 +1,15 @@
+# Clueboard 66%
+
+![Clueboard](https://i.imgur.com/hLePwJu.jpg)
+
+A fully customizable 66% keyboard.
+
+* Keyboard Maintainer: [Zach White](https://github.com/skullydazed)
+* Hardware Supported: Clueboard 66% PCB rev4 (stm32f303cc, PCB Version 3.0)
+* Hardware Availability: [clueboard.co](https://clueboard.co/)
+
+Make example for this keyboard (after setting up your build environment):
+
+    make clueboard/66/rev4:default
+
+See [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) then the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).
diff --git a/keyboards/clueboard/66/rev4/rev4.c b/keyboards/clueboard/66/rev4/rev4.c
new file mode 100644
index 000000000..041c31cd3
--- /dev/null
+++ b/keyboards/clueboard/66/rev4/rev4.c
@@ -0,0 +1,76 @@
+#include "rev4.h"
+//#include "backlight.h"
+
+void matrix_init_kb(void) {
+    // put your keyboard start-up code here
+    // runs once when the firmware starts up
+    matrix_init_user();
+    led_init_ports();
+}
+
+void matrix_scan_kb(void) {
+    matrix_scan_user();
+}
+
+void backlight_init_ports(void) {
+    print("init_backlight_pin()\n");
+    // Set our LED pins as output
+    //DDRD |= (1<<6); // Esc
+    //DDRB |= (1<<7); // Page Up
+    //DDRD |= (1<<4); // Arrows
+
+    // Set our LED pins low
+    //PORTD &= ~(1<<6); // Esc
+    //PORTB &= ~(1<<7); // Page Up
+    //PORTD &= ~(1<<4); // Arrows
+}
+
+void backlight_set(uint8_t level) {
+/*
+    if ( level == 0 ) {
+        // Turn off light
+        PORTD |= (1<<6); // Esc
+        PORTB |= (1<<7); // Page Up
+        PORTD |= (1<<4); // Arrows
+    } else {
+        // Turn on light
+        PORTD &= ~(1<<6); // Esc
+        PORTB &= ~(1<<7); // Page Up
+        PORTD &= ~(1<<4); // Arrows
+    }
+*/
+}
+
+void led_init_ports() {
+    // Set our LED pins as output
+    palSetPadMode(GPIOB, 13, PAL_MODE_OUTPUT_PUSHPULL); // LED1
+    palClearPad(GPIOB, 13);
+    palSetPadMode(GPIOB, 14, PAL_MODE_OUTPUT_PUSHPULL); // LED2
+    palClearPad(GPIOB, 14);
+    palSetPadMode(GPIOA, 8, PAL_MODE_OUTPUT_PUSHPULL); // LED3
+    palClearPad(GPIOA, 8);
+    palSetPadMode(GPIOA, 0, PAL_MODE_OUTPUT_PUSHPULL); // Capslock LED
+    palClearPad(GPIOA, 0);
+}
+
+void led_set_kb(uint8_t usb_led) {
+    if (usb_led & (1<<USB_LED_NUM_LOCK)) {
+        palSetPad(GPIOB, 13);    // LED1
+    } else {
+        palClearPad(GPIOB, 13);  // LED1
+    }
+
+    if (usb_led & (1<<USB_LED_CAPS_LOCK)) {
+        palSetPad(GPIOA, 0);     // Capslock LED
+        palSetPad(GPIOB, 14);    // LED2
+    } else {
+        palClearPad(GPIOA, 0);   // Capslock LED
+        palClearPad(GPIOB, 14);  // LED2
+    }
+
+    if (usb_led & (1<<USB_LED_SCROLL_LOCK)) {
+        palSetPad(GPIOA, 8);     // LED3
+    } else {
+        palClearPad(GPIOA, 8);   // LED3
+    }
+}
diff --git a/keyboards/clueboard/66/rev4/rev4.h b/keyboards/clueboard/66/rev4/rev4.h
new file mode 100644
index 000000000..86688c7a1
--- /dev/null
+++ b/keyboards/clueboard/66/rev4/rev4.h
@@ -0,0 +1,94 @@
+#pragma once
+
+#include "quantum.h"
+
+/* Clueboard matrix layout
+ * ,-----------------------------------------------------------.  ,---.
+ * | 00| 01| 02| 03| 04| 05| 06| 07| 50| 51| 52| 53| 54| 55| 56|  | 57|
+ * |-----------------------------------------------------------|  |---|
+ * |   10| 11| 12| 13| 14| 15| 16| 17| 60| 61| 62| 63| 64|   65|  | 67|
+ * |-----------------------------------------------------------|  `---'
+ * |    20| 21| 22| 23| 24| 25| 26| 27| 70| 71| 72| 73| 74|  75|
+ * |------------------------------------------------------------.
+ * |  30| 31| 32| 33| 34| 35| 36| 37| 80| 81| 82| 83| 84|  85|86|
+ * |------------------------------------------------------------------.
+ * |  40| 41|  42|  43|   45|       46|   90|  92|  93| 94| 95| 96| 97|
+ * `------------------------------------------------------------------'
+ * ,-----------------------------------------------------------.  ,---.
+ * |  `|  1|  2|  3|  4|  5|  6|  7|  8|  9|  0|  -|  =|Yen| BS|  |Ins|
+ * |-----------------------------------------------------------|  |---|
+ * |Tab  |  Q|  W|  E|  R|  T|  Y|  U|  I|  O|  P|  [|  ]|    \|  |Del|
+ * |-----------------------------------------------------------|  `---'
+ * |Caps  |  A|  S|  D|  F|  G|  H|  J|  k|  L|  ;|  '| # | Ent|
+ * |--------------------------------------------------------------.
+ * |Shift| \|  Z|  X|  C|  V|  B|  N|  M|  ,|  .|  /|  \|Shift| Up|
+ * |------------------------------------------------------------------.
+ * |Ctrl|Alt|Gui |MHen| Space| Space|Henk|Gui |Ctrl|  Fn|Left|Down|Rgt|
+ * `------------------------------------------------------------------'
+ */
+// The first section contains all of the arguments
+// The second converts the arguments into a two-dimensional array
+
+#define LAYOUT_all( \
+    k00, k01, k02, k03, k04, k05, k06, k07, k50, k51, k52, k53, k54, k55, k56, k57, \
+    k10, k11, k12, k13, k14, k15, k16, k17, k60, k61, k62, k63, k64, k65,      k67, \
+    k20, k21, k22, k23, k24, k25, k26, k27, k70, k71, k72, k73, k74, k75, \
+    k30, k31, k32, k33, k34, k35, k36, k37, k80, k81, k82, k83, k84, k85, k86, \
+    k40, k41, k42, k43,      k45, k46,      k90,      k92, k93, k94, k95, k96, k97 \
+) { \
+    { k00, k01, k02, k03, k04, k05, k06, k07 }, \
+    { k10, k11, k12, k13, k14, k15, k16, k17 }, \
+    { k20, k21, k22, k23, k24, k25, k26, k27 }, \
+    { k30, k31, k32, k33, k34, k35, k36, k37 }, \
+    { k40, k41, k42, k43, KC_NO, k45, k46, KC_NO }, \
+    { k50, k51, k52, k53, k54, k55, k56, k57 }, \
+    { k60, k61, k62, k63, k64, k65, KC_NO, k67 }, \
+    { k70, k71, k72, k73, k74, k75, KC_NO, KC_NO }, \
+    { k80, k81, k82, k83, k84, k85, k86, KC_NO }, \
+    { k90, KC_NO, k92, k93, k94, k95, k96, k97 }  \
+}
+
+/* LAYOUT_66_ansi, standard 66 key ANSI layout
+ */
+#define LAYOUT_66_ansi( \
+    k00, k01, k02, k03, k04, k05, k06, k07, k50, k51, k52, k53, k54,   k56,    k57, \
+    k10, k11, k12, k13, k14, k15, k16, k17, k60, k61, k62, k63, k64, k65,      k67, \
+    k20, k21, k22, k23, k24, k25, k26, k27, k70, k71, k72, k73,    k75, \
+    k30,      k32, k33, k34, k35, k36, k37, k80, k81, k82, k83,    k85,   k86, \
+    k40, k41, k42,                k46,                k92, k93, k94, k95, k96, k97 \
+) { \
+    { k00, k01, k02, k03, k04, k05, k06, k07 }, \
+    { k10, k11, k12, k13, k14, k15, k16, k17 }, \
+    { k20, k21, k22, k23, k24, k25, k26, k27 }, \
+    { k30, KC_NO, k32, k33, k34, k35, k36, k37 }, \
+    { k40, k41, k42, KC_NO, KC_NO, KC_NO, k46, KC_NO }, \
+    { k50, k51, k52, k53, k54, KC_NO, k56, k57 }, \
+    { k60, k61, k62, k63, k64, k65, KC_NO, k67 }, \
+    { k70, k71, k72, k73, KC_NO, k75, KC_NO, KC_NO }, \
+    { k80, k81, k82, k83, KC_NO, k85, k86, KC_NO }, \
+    { KC_NO, KC_NO, k92, k93, k94, k95, k96, k97 }  \
+}
+
+/* LAYOUT_66_iso, standard 67 key ISO layout
+ */
+#define LAYOUT_66_iso( \
+    k00, k01, k02, k03, k04, k05, k06, k07, k50, k51, k52, k53, k54,    k56,   k57, \
+    k10, k11, k12, k13, k14, k15, k16, k17, k60, k61, k62, k63, k64,           k67, \
+    k20, k21, k22, k23, k24, k25, k26, k27, k70, k71, k72, k73, k74, k75, \
+    k30, k31, k32, k33, k34, k35, k36, k37, k80, k81, k82, k83,    k85,   k86, \
+    k40, k41, k42,                k46,                k92, k93, k94, k95, k96, k97 \
+) { \
+    { k00, k01, k02, k03, k04, k05, k06, k07 }, \
+    { k10, k11, k12, k13, k14, k15, k16, k17 }, \
+    { k20, k21, k22, k23, k24, k25, k26, k27 }, \
+    { k30, k31, k32, k33, k34, k35, k36, k37 }, \
+    { k40, k41, k42, KC_NO, KC_NO, KC_NO, k46, KC_NO }, \
+    { k50, k51, k52, k53, k54, KC_NO, k56, k57 }, \
+    { k60, k61, k62, k63, k64, KC_NO, KC_NO, k67 }, \
+    { k70, k71, k72, k73, k74, k75, KC_NO, KC_NO }, \
+    { k80, k81, k82, k83, KC_NO, k85, k86, KC_NO }, \
+    { KC_NO, KC_NO, k92, k93, k94, k95, k96, k97 }  \
+}
+
+#define KEYMAP LAYOUT_all
+#define LAYOUT LAYOUT_all
diff --git a/keyboards/clueboard/66/rev4/rules.mk b/keyboards/clueboard/66/rev4/rules.mk
new file mode 100644
index 000000000..846b1eee0
--- /dev/null
+++ b/keyboards/clueboard/66/rev4/rules.mk
@@ -0,0 +1,32 @@
+LAYOUTS = 66_ansi 66_iso
+
+## chip/board settings
+MCU_FAMILY = STM32
+MCU_SERIES = STM32F3xx
+MCU_LDSCRIPT = STM32F303xC
+MCU_STARTUP = stm32f3xx
+BOARD = GENERIC_STM32_F303XC
+MCU  = cortex-m4
+ARMV = 7
+USE_FPU = yes
+OPT_DEFS =
+
+# Options to pass to dfu-util when flashing
+DFU_ARGS = -d 0483:df11 -a 0 -s 0x08000000:leave
+
+# Build Options
+#   comment out to disable the options.
+#
+BACKLIGHT_ENABLE = yes
+BOOTMAGIC_ENABLE = no   # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = yes   # Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes   # Audio control and System control(+450)
+CONSOLE_ENABLE = yes    # Console for debug(+400)
+COMMAND_ENABLE = no     # Commands for debug and configuration
+NKRO_ENABLE = yes       # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+AUDIO_ENABLE = no
+RGBLIGHT_ENABLE = no    # Enable keyboard underlight functionality
+MIDI_ENABLE = no        # MIDI controls
+UNICODE_ENABLE = no     # Unicode
+BLUETOOTH_ENABLE = no   # Enable Bluetooth with the Adafruit EZ-Key HID
+AUDIO_ENABLE = yes