diff options
| -rw-r--r-- | keyboards/kitten_paw/Makefile | 77 | ||||
| -rw-r--r-- | keyboards/kitten_paw/config.h | 162 | ||||
| -rw-r--r-- | keyboards/kitten_paw/keymaps/default/keymap.c | 51 | ||||
| -rw-r--r-- | keyboards/kitten_paw/kitten_paw.c | 30 | ||||
| -rw-r--r-- | keyboards/kitten_paw/kitten_paw.h | 47 | ||||
| -rw-r--r-- | keyboards/kitten_paw/led.c | 47 | ||||
| -rw-r--r-- | keyboards/kitten_paw/matrix.c | 164 | ||||
| -rw-r--r-- | keyboards/kitten_paw/readme.md | 32 | ||||
| -rw-r--r-- | keyboards/readme.md | 1 |
9 files changed, 611 insertions, 0 deletions
diff --git a/keyboards/kitten_paw/Makefile b/keyboards/kitten_paw/Makefile new file mode 100644 index 000000000..912292173 --- /dev/null +++ b/keyboards/kitten_paw/Makefile @@ -0,0 +1,77 @@ + + +# MCU name +#MCU = at90usb1287 +MCU = atmega32u2 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + +# Boot Section Size in *bytes* +# Teensy halfKay 512 +# Teensy++ halfKay 1024 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +# USBaspLoader 2048 + OPT_DEFS += -DBOOTLOADER_SIZE=4096 + + +# Build Options +# change yes to no to disable +# +BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) +EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) +CONSOLE_ENABLE ?= yes # Console for debug(+400) +COMMAND_ENABLE ?= yes # Commands for debug and configuration +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend +# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +NKRO_ENABLE ?= no # USB Nkey Rollover +BACKLIGHT_ENABLE ?= no # Enable keyboard backlight functionality on B7 by default +MIDI_ENABLE ?= no # MIDI controls +UNICODE_ENABLE ?= no # Unicode +BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID +AUDIO_ENABLE ?= no # Audio output on port C6 + +CUSTOM_MATRIX = yes +SRC += matrix.c led.c + +ifndef QUANTUM_DIR + include ../../Makefile +endif + diff --git a/keyboards/kitten_paw/config.h b/keyboards/kitten_paw/config.h new file mode 100644 index 000000000..d7089734a --- /dev/null +++ b/keyboards/kitten_paw/config.h @@ -0,0 +1,162 @@ +/* +Copyright 2012 Jun Wako <wakojun@gmail.com> + +This program is free software: you can redistribute it and/or modify +it under the terms of the GNU General Public License as published by +the Free Software Foundation, either version 2 of the License, or +(at your option) any later version. + +This program is distributed in the hope that it will be useful, +but WITHOUT ANY WARRANTY; without even the implied warranty of +MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +GNU General Public License for more details. + +You should have received a copy of the GNU General Public License +along with this program. If not, see <http://www.gnu.org/licenses/>. +*/ + +#ifndef CONFIG_H +#define CONFIG_H + +#include "config_common.h" + + +/* USB Device descriptor parameter */ +#define VENDOR_ID 0xFEED +#define PRODUCT_ID 0x6050 +#define DEVICE_VER 0x0104 +#define MANUFACTURER Costar +#define PRODUCT Majestouch + +/* key matrix size */ +#define MATRIX_ROWS 8 +#define MATRIX_COLS 18 + +/* + * Keyboard Matrix Assignments + * + * Change this to how you wired your keyboard + * COLS: AVR pins used for columns, left to right + * ROWS: AVR pins used for rows, top to bottom + * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode) + * ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode) + * +*/ +//#define MATRIX_ROW_PINS { D0, D5 } +//#define MATRIX_COL_PINS { F1, F0, B0 } +//#define UNUSED_PINS + +/* COL2ROW or ROW2COL */ +#define DIODE_DIRECTION COL2ROW + +// #define BACKLIGHT_PIN B7 +// #define BACKLIGHT_BREATHING +// #define BACKLIGHT_LEVELS 3 + + +/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */ +#define DEBOUNCING_DELAY 5 + +/* define if matrix has ghost (lacks anti-ghosting diodes) */ +//#define MATRIX_HAS_GHOST + +/* number of backlight levels */ + +/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ +#define LOCKING_SUPPORT_ENABLE +/* Locking resynchronize hack */ +#define LOCKING_RESYNC_ENABLE + +/* + * Force NKRO + * + * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved + * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the + * makefile for this to work.) + * + * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N) + * until the next keyboard reset. + * + * NKRO may prevent your keystrokes from being detected in the BIOS, but it is + * fully operational during normal computer usage. + * + * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N) + * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by + * bootmagic, NKRO mode will always be enabled until it is toggled again during a + * power-up. + * + */ +//#define FORCE_NKRO + +/* + * Magic Key Options + * + * Magic keys are hotkey commands that allow control over firmware functions of + * the keyboard. They are best used in combination with the HID Listen program, + * found here: https://www.pjrc.com/teensy/hid_listen.html + * + * The options below allow the magic key functionality to be changed. This is + * useful if your keyboard/keypad is missing keys and you want magic key support. + * + */ + +/* key combination for magic key command */ +#define IS_COMMAND() ( \ + keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \ +) + +/* control how magic key switches layers */ +//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS true +//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS true +//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM false + +/* override magic key keymap */ +//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS +//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS +//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM +//#define MAGIC_KEY_HELP1 H +//#define MAGIC_KEY_HELP2 SLASH +//#define MAGIC_KEY_DEBUG D +//#define MAGIC_KEY_DEBUG_MATRIX X +//#define MAGIC_KEY_DEBUG_KBD K +//#define MAGIC_KEY_DEBUG_MOUSE M +//#define MAGIC_KEY_VERSION V +//#define MAGIC_KEY_STATUS S +//#define MAGIC_KEY_CONSOLE C +//#define MAGIC_KEY_LAYER0_ALT1 ESC +//#define MAGIC_KEY_LAYER0_ALT2 GRAVE +//#define MAGIC_KEY_LAYER0 0 +//#define MAGIC_KEY_LAYER1 1 +//#define MAGIC_KEY_LAYER2 2 +//#define MAGIC_KEY_LAYER3 3 +//#define MAGIC_KEY_LAYER4 4 +//#define MAGIC_KEY_LAYER5 5 +//#define MAGIC_KEY_LAYER6 6 +//#define MAGIC_KEY_LAYER7 7 +//#define MAGIC_KEY_LAYER8 8 +//#define MAGIC_KEY_LAYER9 9 +//#define MAGIC_KEY_BOOTLOADER PAUSE +//#define MAGIC_KEY_LOCK CAPS +//#define MAGIC_KEY_EEPROM E +//#define MAGIC_KEY_NKRO N +//#define MAGIC_KEY_SLEEP_LED Z + +/* + * Feature disable options + * These options are also useful to firmware size reduction. + */ + +/* disable debug print */ +//#define NO_DEBUG + +/* disable print */ +//#define NO_PRINT + +/* disable action features */ +//#define NO_ACTION_LAYER +//#define NO_ACTION_TAPPING +//#define NO_ACTION_ONESHOT +//#define NO_ACTION_MACRO +//#define NO_ACTION_FUNCTION + +#endif diff --git a/keyboards/kitten_paw/keymaps/default/keymap.c b/keyboards/kitten_paw/keymaps/default/keymap.c new file mode 100644 index 000000000..f67235745 --- /dev/null +++ b/keyboards/kitten_paw/keymaps/default/keymap.c @@ -0,0 +1,51 @@ +#include "kitten_paw.h" + +enum layers { + DEFAULT, +}; + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { + [DEFAULT] = KEYMAP(\ + KC_ESC, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, KC_PSCR,KC_SLCK,KC_PAUS, \ + KC_GRV, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0,KC_MINS, KC_EQL,KC_BSPC, KC_INS,KC_HOME,KC_PGUP, KC_NLCK,KC_PSLS,KC_PAST,KC_PMNS, \ + KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P,KC_LBRC,KC_RBRC,KC_BSLS, KC_DEL, KC_END,KC_PGDN, KC_P7, KC_P8, KC_P9,KC_PPLS, \ + KC_CAPS, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L,KC_SCLN,KC_QUOT, KC_ENT, KC_P4, KC_P5, KC_P6, \ + KC_LSFT,KC_NUBS, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M,KC_COMM, KC_DOT,KC_SLSH, KC_RSFT, KC_UP, KC_P1, KC_P2, KC_P3,KC_PENT, \ + KC_LCTL,KC_LGUI,KC_LALT, KC_SPC, KC_RALT,KC_RGUI,KC_MENU,KC_RCTL, KC_LEFT,KC_DOWN,KC_RGHT, KC_P0,KC_PDOT) +}; + +const uint16_t PROGMEM fn_actions[] = { + +}; + +const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt) +{ + // MACRODOWN only works in this function + switch(id) { + case 0: + if (record->event.pressed) { + register_code(KC_RSFT); + } else { + unregister_code(KC_RSFT); + } + break; + } + return MACRO_NONE; +}; + + +void matrix_init_user(void) { + +} + +void matrix_scan_user(void) { + +} + +bool process_record_user(uint16_t keycode, keyrecord_t *record) { + return true; +} + +void led_set_user(uint8_t usb_led) { + +}
\ No newline at end of file diff --git a/keyboards/kitten_paw/kitten_paw.c b/keyboards/kitten_paw/kitten_paw.c new file mode 100644 index 000000000..8713baf43 --- /dev/null +++ b/keyboards/kitten_paw/kitten_paw.c @@ -0,0 +1,30 @@ +#include "kitten_paw.h" + +void matrix_init_kb(void) { + // put your keyboard start-up code here + // runs once when the firmware starts up + + matrix_init_quantum(); + matrix_init_user(); +} + +void matrix_scan_kb(void) { + // put your looping keyboard code here + // runs every cycle (a lot) + + matrix_scan_quantum(); + matrix_scan_user(); +} + +bool process_record_kb(uint16_t keycode, keyrecord_t *record) { + // put your per-action keyboard code here + // runs for every action, just before processing by the firmware + + return process_record_user(keycode, record); +} + +void led_set_kb(uint8_t usb_led) { + // put your keyboard LED indicator (ex: Caps Lock LED) toggling code here + + led_set_user(usb_led); +} diff --git a/keyboards/kitten_paw/kitten_paw.h b/keyboards/kitten_paw/kitten_paw.h new file mode 100644 index 000000000..a6c1d27de --- /dev/null +++ b/keyboards/kitten_paw/kitten_paw.h @@ -0,0 +1,47 @@ +#ifndef KITTEN_PAW_H +#define KITTEN_PAW_H + +#include "quantum.h" + +// This a shortcut to help you visually see your layout. +// The first section contains all of the arguements +// The second converts the arguments into a two-dimensional array +/* + Matrix col/row mapping + + ,----. ,-------------------. ,-------------------. ,-------------------. ,--------------. + | J6 | | I4 | H4 | H2 | H6 | | A7 | E6 | D2 | D4 | | B4 | B7 | B6 | B0 | | C7 | C5 | A5 | + `----' `-------------------' `-------------------' `-------------------' `--------------' + ,-------------------------------------------------------------------------. ,--------------. ,-------------------. + | J4 | J7 | I7 | H7 | G7 | G4 | F4 | F7 | E7 | D7 | R7 | R4 | E4 | B2 | | L4 | O4 | Q4 | | K1 | L1 | Q1 | Q0 | + |-------------------------------------------------------------------------| |--------------| |-------------------| + | J2 | J5 | I5 | H5 | G5 | G2 | F2 | F5 | E5 | D5 | R5 | R2 | E2 | B3 | | K4 | O7 | Q7 | | K5 | L5 | Q5 | O5 | + |-------------------------------------------------------------------------| '--------------' |-------------- | + | O5 | J3 | I3 | H3 | G3 | G6 | F6 | F3 | E3 | D3 | R3 | R6 | B1 | | K2 | L2 | Q2 | | + |-------------------------------------------------------------------------| ,----. |-------------------| + | N2 | J1 | I1 | H1 | G1 | G0 | F0 | F1 | E1 | D1 | R0 | N3 | | O6 | | K3 | L3 | Q3 | O3 | + |-------------------------------------------------------------------------| ,--------------. |-------------- | + | A4 | P2 | C6 | K6 | C0 | M3 | D0 | A1 | | O0 | K0 | L0 | | L6 | Q6 | | + `-------------------------------------------------------------------------' `--------------' `-------------------' +*/ + +#define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{ \ + {KC_NO, KB0, KC0, KD0,KC_NO, KF0, KG0,KC_NO,KC_NO,KC_NO, KK0, KL0,KC_NO,KC_NO, KO0,KC_NO, KQ0, KR0}, \ + { KA1, KB1,KC_NO, KD1, KE1, KF1, KG1, KH1, KI1, KJ1, KK1, KL1,KC_NO,KC_NO,KC_NO,KC_NO, KQ1,KC_NO}, \ + {KC_NO, KB2,KC_NO, KD2, KE2, KF2, KG2, KH2, KI2, KJ2, KK2, KL2,KC_NO, KN2,KC_NO, KP2, KQ2, KR2}, \ + {KC_NO, KB3,KC_NO, KD3, KE3, KF3, KG3, KH3, KI3, KJ3, KK3, KL3, KM3, KN3, KO3,KC_NO, KQ3, KR3}, \ + { KA4, KB4,KC_NO, KD4, KE4, KF4, KG4, KH4, KI4, KJ4, KK4, KL4,KC_NO,KC_NO, KO4,KC_NO, KQ4, KR4}, \ + { KA5,KC_NO, KC5, KD5, KE5, KF5, KG5, KH5, KI5, KJ5, KK5, KL5,KC_NO,KC_NO, KO5,KC_NO, KQ5, KR5}, \ + {KC_NO, KB6, KC6,KC_NO, KE6, KF6, KG6, KH6, KI6, KJ6, KK6, KL6,KC_NO,KC_NO, KO6,KC_NO, KQ6, KR6}, \ + { KA7, KB7, KC7, KD7, KE7, KF7, KG7, KH7, KI7, KJ7,KC_NO,KC_NO,KC_NO,KC_NO, KO7,KC_NO, KQ7, KR7} \ +} + +#endif diff --git a/keyboards/kitten_paw/led.c b/keyboards/kitten_paw/led.c new file mode 100644 index 000000000..a1bf057c4 --- /dev/null +++ b/keyboards/kitten_paw/led.c @@ -0,0 +1,47 @@ +/* + Copyright 2014 Ralf Schmitt <ralf@bunkertor.net> + + This program is free software: you can redistribute it and/or modify + it under the terms of the GNU General Public License as published by + the Free Software Foundation, either version 2 of the License, or + (at your option) any later version. + + This program is distributed in the hope that it will be useful, + but WITHOUT ANY WARRANTY; without even the implied warranty of + MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + GNU General Public License for more details. + + You should have received a copy of the GNU General Public License + along with this program. If not, see <http://www.gnu.org/licenses/>. +*/ + +#include <avr/io.h> +#include "stdint.h" +#include "led.h" + +/* LED pin configuration + * + * Scroll Lock PC5 + * Caps Lock PC6 + * Num Lock PB7 + * + */ +void led_set(uint8_t usb_led) { + DDRB |= (1<<7); + DDRC |= (1<<5) | (1<<6); + + if (usb_led & (1<<USB_LED_CAPS_LOCK)) + PORTC &= ~(1<<6); + else + PORTC |= (1<<6); + + if (usb_led & (1<<USB_LED_NUM_LOCK)) + PORTB &= ~(1<<7); + else + PORTB |= (1<<7); + + if (usb_led & (1<<USB_LED_SCROLL_LOCK)) + PORTC &= ~(1<<5); + else + PORTC |= (1<<5); +} diff --git a/keyboards/kitten_paw/matrix.c b/keyboards/kitten_paw/matrix.c new file mode 100644 index 000000000..46875293f --- /dev/null +++ b/keyboards/kitten_paw/matrix.c @@ -0,0 +1,164 @@ +/* + Copyright 2014 Ralf Schmitt <ralf@bunkertor.net> + + This program is free software: you can redistribute it and/or modify + it under the terms of the GNU General Public License as published by + the Free Software Foundation, either version 2 of the License, or + (at your option) any later version. + + This program is distributed in the hope that it will be useful, + but WITHOUT ANY WARRANTY; without even the implied warranty of + MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + GNU General Public License for more details. + + You should have received a copy of the GNU General Public License + along with this program. If not, see <http://www.gnu.org/licenses/>. +*/ + +#include <stdint.h> +#include <stdbool.h> +#include <avr/io.h> +#include <util/delay.h> +#include "print.h" +#include "debug.h" +#include "util.h" +#include "matrix.h" + +#ifndef DEBOUNCING_DELAY +# define DEBOUNCING_DELAY 5 +#endif +static uint8_t debouncing = DEBOUNCING_DELAY; + +static matrix_row_t matrix[MATRIX_ROWS]; +static matrix_row_t matrix_debouncing[MATRIX_ROWS]; + +static uint8_t read_rows(void); +static void select_col(uint8_t col); + +inline uint8_t matrix_rows(void) { + return MATRIX_ROWS; +} + +inline uint8_t matrix_cols(void) { + return MATRIX_COLS; +} + +/* Column pin configuration + * + * col: 0 1 2 3 4 5 6 7 + * pin: PC7 PD5 PD3 PD1 PC2 PD6 PD4 PD2 + * + * Rrr pin configuration + * + * These rrrs uses one 74HC154 4 to 16 bit demultiplexer (low + * active), together with 2 rrrs driven directly from the micro + * controller, to control the 18 rrrs. The rrrs are driven from + * pins B6,5,4,3,2,1,0. + */ +void matrix_init(void) { + DDRC &= ~0b10000100; // Row input pins + DDRD &= ~0b01111110; + PORTC |= 0b10000100; + PORTD |= 0b01111110; + + DDRB |= 0b01111111; // Column output pins + + for (uint8_t i=0; i < MATRIX_ROWS; i++) { + matrix[i] = 0; + matrix_debouncing[i] = 0; + } +} + +uint8_t matrix_scan(void) { + for (uint8_t col = 0; col < MATRIX_COLS; col++) { + select_col(col); + _delay_us(3); + uint8_t rows = read_rows(); + for (uint8_t row = 0; row < MATRIX_ROWS; row++) { + bool prev_bit = matrix_debouncing[row] & ((matrix_row_t)1<<col); + bool curr_bit = rows & (1<<row); + if (prev_bit != curr_bit) { + matrix_debouncing[row] ^= ((matrix_row_t)1<<col); + debouncing = DEBOUNCING_DELAY; + } + } + } + + if (debouncing) { + if (--debouncing) { + _delay_ms(1); + } + else { + for (uint8_t i = 0; i < MATRIX_ROWS; i++) { + matrix[i] = matrix_debouncing[i]; + } + } + } + + return 1; +} + +bool matrix_is_modified(void) { + if (debouncing) + return false; + else + return true; +} + +inline bool matrix_is_on(uint8_t row, uint8_t col) { + return (matrix[row] & ((matrix_row_t)1<<col)); +} + +inline matrix_row_t matrix_get_row(uint8_t row) { + return matrix[row]; +} + +void matrix_print(void) { + print("\nr/c 0123456789ABCDEF\n"); + for (uint8_t row = 0; row < MATRIX_ROWS; row++) { + xprintf("%02X: %032lb\n", row, bitrev32(matrix_get_row(row))); + } +} + +uint8_t matrix_key_count(void) { + uint8_t count = 0; + for (uint8_t i = 0; i < MATRIX_ROWS; i++) { + count += bitpop32(matrix[i]); + } + return count; +} + +static uint8_t read_rows(void) { + return + (PINC&(1<<7) ? 0 : (1<<0)) | + (PIND&(1<<5) ? 0 : (1<<1)) | + (PIND&(1<<3) ? 0 : (1<<2)) | + (PIND&(1<<1) ? 0 : (1<<3)) | + (PINC&(1<<2) ? 0 : (1<<4)) | + (PIND&(1<<2) ? 0 : (1<<5)) | + (PIND&(1<<4) ? 0 : (1<<6)) | + (PIND&(1<<6) ? 0 : (1<<7)); +} + +static void select_col(uint8_t col) { + switch (col) { + case 0: PORTB = (PORTB & ~0b01111111) | 0b01100100; break; + case 1: PORTB = (PORTB & ~0b01111111) | 0b01101100; break; + case 2: PORTB = (PORTB & ~0b01111111) | 0b01100010; break; + case 3: PORTB = (PORTB & ~0b01111111) | 0b01111010; break; + case 4: PORTB = (PORTB & ~0b01111111) | 0b01100110; break; + case 5: PORTB = (PORTB & ~0b01111111) | 0b01110110; break; + case 6: PORTB = (PORTB & ~0b01111111) | 0b01101110; break; + case 7: PORTB = (PORTB & ~0b01111111) | 0b01111110; break; + case 8: PORTB = (PORTB & ~0b01111111) | 0b01000001; break; + case 9: PORTB = (PORTB & ~0b01111111) | 0b00100001; break; + case 10: PORTB = (PORTB & ~0b01111111) | 0b01101010; break; + case 11: PORTB = (PORTB & ~0b01111111) | 0b01110010; break; + case 12: PORTB = (PORTB & ~0b01111111) | 0b01111100; break; + case 13: PORTB = (PORTB & ~0b01111111) | 0b01110100; break; + case 14: PORTB = (PORTB & ~0b01111111) | 0b01111000; break; + case 15: PORTB = (PORTB & ~0b01111111) | 0b01110000; break; + case 16: PORTB = (PORTB & ~0b01111111) | 0b01100000; break; + case 17: PORTB = (PORTB & ~0b01111111) | 0b01101000; break; + } +} diff --git a/keyboards/kitten_paw/readme.md b/keyboards/kitten_paw/readme.md new file mode 100644 index 000000000..a6ef2a067 --- /dev/null +++ b/keyboards/kitten_paw/readme.md @@ -0,0 +1,32 @@ +kitten_paw keyboard firmware +====================== +This is the firmware for the 2016 revision of the Kitten Paw controller by Bathroom Epiphanies. +Most of the boilerplate code is the work of [BathroomEpiphanies](https://github.com/BathroomEpiphanies). + +NKRO doesn't work at the moment, I don't know if I will take the time to find out how to fix this, so far 6KRO is enough for me. + +## Quantum MK Firmware + +For the full Quantum feature list, see [the parent readme.md](/doc/readme.md). + +## Building + +Download or clone the whole firmware and navigate to the keyboards/kitten_paw folder. Once your dev env is setup, you'll be able to type `make` to generate your .hex - you can then use the Teensy Loader to program your .hex file. + +Depending on which keymap you would like to use, you will have to compile slightly differently. + +### Default + +To build with the default keymap, simply run `make`. + +### Other Keymaps + +Several version of keymap are available in advance but you are recommended to define your favorite layout yourself. To define your own keymap create a folder with the name of your keymap in the keymaps folder, and see keymap documentation (you can find in top readme.md) and existant keymap files. + +To build the firmware binary hex file with a keymap just do `make` with `keymap` option like: + +``` +$ make keymap=[default|jack|<name>] +``` + +Keymaps follow the format **__keymap.c__** and are stored in folders in the `keymaps` folder, eg `keymaps/my_keymap/` diff --git a/keyboards/readme.md b/keyboards/readme.md index f6c90b1f6..4f1796219 100644 --- a/keyboards/readme.md +++ b/keyboards/readme.md @@ -39,6 +39,7 @@ These keyboards are part of the QMK repository, but their manufacturers are not * [hhkb](/keyboards/hhkb) — The Happy Hacking keyboard can be hacked with a custom controller to run QMK. * [jd45](/keyboards/jd45) — Another Geekhack community project, designed by jdcarpe. * [kc60](/keyboards/kc60) — A programmable Chinese-made keyboard, lost in the mists of time. +* [kitten_paw](/keyboards/kitten_paw) — A replacement controller (2016 revision) for the Filco Majestouch by [Bathroom Epiphanies](https://github.com/BathroomEpiphanies) * [phantom](/keyboards/phantom) — A tenkeyless kit by Teel, also from Geekhack. * [retro_refit](/keyboards/retro_refit) — Another creation by IBNobody. * [satan](/keyboards/satan) — A GH60 variant. |