diff options
Diffstat (limited to 'Projects/Magstripe/Magstripe.txt')
| -rw-r--r-- | Projects/Magstripe/Magstripe.txt | 163 |
1 files changed, 163 insertions, 0 deletions
diff --git a/Projects/Magstripe/Magstripe.txt b/Projects/Magstripe/Magstripe.txt new file mode 100644 index 000000000..a11dfaf80 --- /dev/null +++ b/Projects/Magstripe/Magstripe.txt @@ -0,0 +1,163 @@ +/** \file + * + * This file contains special DoxyGen information for the generation of the main page and other special + * documentation pages. It is not a project source file. + */ + +/** \mainpage Denver Gingerich's USBSnoop Magnetic Card Reader Project + * + * \section Sec_Compat Project Compatibility: + * + * The following list indicates what microcontrollers are compatible with this project. + * + * \li AT90USB1287 + * \li AT90USB1286 + * + * \section Sec_Info USB Information: + * + * The following table gives a rundown of the USB utilization of this project. + * + * <table> + * <tr> + * <td><b>USB Mode:</b></td> + * <td>Device</td> + * </tr> + * <tr> + * <td><b>USB Class:</b></td> + * <td>Human Interface Device (HID)</td> + * </tr> + * <tr> + * <td><b>USB Subclass:</b></td> + * <td>Keyboard</td> + * </tr> + * <tr> + * <td><b>Relevant Standards:</b></td> + * <td>USBIF HID Standard, USBIF HID Usage Tables</td> + * </tr> + * <tr> + * <td><b>Supported USB Speeds:</b></td> + * <td>Full Speed Mode</td> + * </tr> + * </table> + * + * \section Sec_Description Project Description: + * + * Firmware for a USB AVR powered USB TTL magnetic stripe reader (using a card + * reader such as the Omron V3B-4K) by Denver Gingerich. This project is designed + * to be used with the open source Stripe Snoop project at <a>http://stripesnoop.sourceforge.net/</a>. + * + * See <a>http://ossguy.com/ss_usb/</a> for the USB reader hardware project website, + * including construction and support details. + * + * To use, connect your magnetic card reader device to the USB AVR as follows (pin and port mapping may be adjusted + * from the project makefile): + * + * <table> + * <tr> + * <th><b>Signal:</b></th> + * <th><b>AVR Port:</b></th> + * </tr> + * <tr> + * <td>Track 1 Data</td> + * <td>PORTC, Pin 1</td> + * </tr> + * <tr> + * <td>Track 1 Clock</td> + * <td>PORTC, Pin 2</td> + * </tr> + * <tr> + * <td>Track 2 Data</td> + * <td>PORTC, Pin 3</td> + * </tr> + * <tr> + * <td>Track 2 Clock</td> + * <td>PORTC, Pin 0</td> + * </tr> + * <tr> + * <td>Track 3 Data</td> + * <td>PORTC, Pin 5</td> + * </tr> + * <tr> + * <td>Track 3 Clock</td> + * <td>PORTC, Pin 6</td> + * </tr> + * <tr> + * <td>Card Detect</td> + * <td>PORTC, Pin 4</td> + * </tr> + * </table> + * + * This project is based on the LUFA Keyboard project demonstration application, written by Denver Gingerich. + * + * This application uses a keyboard HID driver to communicate the data collected a TTL magnetic stripe reader + * to the connected computer. The raw bitstream obtained from the magnetic stripe reader is "typed" through + * the keyboard driver as 0's and 1's. After every card swipe, the project will send a return key. + * + * \section Sec_Options Project Options + * + * The following defines can be found in this project, which can control the project behaviour when defined, or changed in value. + * + * <table> + * <tr> + * <th><b>Define Name:</b></th> + * <th><b>Location:</b></th> + * <th><b>Description:</b></th> + * </tr> + * <tr> + * <td>MAX_BITS</td> + * <td>CircularBitBuffer.h</td> + * <td>Gives the maximum number of bits per track which can be buffered by the device for later transmission to a host.</td> + * </tr> + * <tr> + * <td>MAG_T1_CLOCK</td> + * <td>AppConfig.h</td> + * <td>Mask for the magnetic card reader's CLOCK line for the reader's track 1 output.</td> + * </tr> + * <tr> + * <td>MAG_T1_DATA</td> + * <td>AppConfig.h</td> + * <td>Mask for the magnetic card reader's DATA line for the reader's track 1 output.</td> + * </tr> + * <tr> + * <td>MAG_T2_CLOCK</td> + * <td>AppConfig.h</td> + * <td>Mask for the magnetic card reader's CLOCK line for the reader's track 2 output.</td> + * </tr> + * <tr> + * <td>MAG_T2_DATA</td> + * <td>AppConfig.h</td> + * <td>Mask for the magnetic card reader's DATA line for the reader's track 2 output.</td> + * </tr> + * <tr> + * <td>MAG_T3_CLOCK</td> + * <td>AppConfig.h</td> + * <td>Mask for the magnetic card reader's CLOCK line for the reader's track 3 output.</td> + * </tr> + * <tr> + * <td>MAG_T3_DATA</td> + * <td>AppConfig.h</td> + * <td>Mask for the magnetic card reader's DATA line for the reader's track 3 output.</td> + * </tr> + * <tr> + * <td>MAG_CARDPRESENT</td> + * <td>AppConfig.h</td> + * <td>Mask for the magnetic card reader's card detection output.</td> + * </tr> + * <tr> + * <td>MAG_PIN</td> + * <td>AppConfig.h</td> + * <td>PIN register that the magnetic card reader device is attached to.</td> + * </tr> + * <tr> + * <td>MAG_PORT</td> + * <td>AppConfig.h</td> + * <td>PORT register that the magnetic card reader device is attached to.</td> + * </tr> + * <tr> + * <td>MAG_DDR</td> + * <td>AppConfig.h</td> + * <td>DDR register that the magnetic card reader device is attached to.</td> + * </tr> + * </table> + */ + |