diff options
Diffstat (limited to 'keyboard/hhkb/not_supported/Makefile.iwrap')
| -rw-r--r-- | keyboard/hhkb/not_supported/Makefile.iwrap | 103 |
1 files changed, 103 insertions, 0 deletions
diff --git a/keyboard/hhkb/not_supported/Makefile.iwrap b/keyboard/hhkb/not_supported/Makefile.iwrap new file mode 100644 index 000000000..2d9d82c48 --- /dev/null +++ b/keyboard/hhkb/not_supported/Makefile.iwrap @@ -0,0 +1,103 @@ +# +# Makefile for iWRAP +# + + +# Target file name (without extension). +TARGET = hhkb_iwrap + +# Directory common source filess exist +TOP_DIR = ../.. + +# Directory keyboard dependent files exist +TARGET_DIR = . + +# keyboard dependent files +SRC = \ + keymap.c \ + matrix.c \ + led.c + +CONFIG_H = config_iwrap.h + + +# V-USB debug level: To use ps2_usart.c level must be 0 +# ps2_usart.c requires USART to receive PS/2 signal. +OPT_DEFS = -DDEBUG_LEVEL=0 + + +# MCU name, you MUST set this to match the board you are using +# type "make clean" after changing this, so all files will be rebuilt +MCU = atmega328p + + +# Processor frequency. +# Normally the first thing your program should do is set the clock prescaler, +# so your program will run at the correct speed. You should also set this +# variable to same clock speed. The _delay_ms() macro uses this, and many +# examples use this variable to calculate timings. Do not add a "UL" here. +F_CPU = 12000000 + + +# Boot Section Size in *bytes* +# Teensy halfKay 512 +# Teensy++ halfKay 1024 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +# USBaspLoader 2048 +OPT_DEFS += -DBOOTLOADER_SIZE=2048 + + +# Build Options +# comment out to disable the options. +# +BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration +MOUSEKEY_ENABLE = yes # Mouse keys +EXTRAKEY_ENABLE = yes # Audio control and System control +CONSOLE_ENABLE = yes # Console for debug +COMMAND_ENABLE = yes # Commands for debug and configuration +#NKRO_ENABLE = yes # USB Nkey Rollover + + + +#---------------- Programming Options -------------------------- +AVRDUDE = avrdude +# Type: avrdude -c ? to get a full listing. +AVRDUDE_PROGRAMMER = usbasp +AVRDUDE_PORT = +AVRDUDE_WRITE_FLASH = -U flash:w:$(TARGET).hex +#AVRDUDE_WRITE_EEPROM = -U eeprom:w:$(TARGET).eep + +# Uncomment the following if you want avrdude's erase cycle counter. +# Note that this counter needs to be initialized first using -Yn, +# see avrdude manual. +#AVRDUDE_ERASE_COUNTER = -y + +# Uncomment the following if you do /not/ wish a verification to be +# performed after programming the device. +#AVRDUDE_NO_VERIFY = -V + +# Increase verbosity level. Please use this when submitting bug +# reports about avrdude. See <http://savannah.nongnu.org/projects/avrdude> +# to submit bug reports. +#AVRDUDE_VERBOSE = -v -v + +#AVRDUDE_FLAGS = -p $(MCU) -P $(AVRDUDE_PORT) -c $(AVRDUDE_PROGRAMMER) +AVRDUDE_FLAGS = -p $(MCU) -c $(AVRDUDE_PROGRAMMER) +AVRDUDE_FLAGS += $(AVRDUDE_NO_VERIFY) +AVRDUDE_FLAGS += $(AVRDUDE_VERBOSE) +AVRDUDE_FLAGS += $(AVRDUDE_ERASE_COUNTER) + +PROGRAM_CMD = $(AVRDUDE) $(AVRDUDE_FLAGS) $(AVRDUDE_WRITE_FLASH) $(AVRDUDE_WRITE_EEPROM) + + + +# Search Path +VPATH += $(TARGET_DIR) +VPATH += $(TOP_DIR) + +include $(TOP_DIR)/protocol/iwrap.mk +# TODO: to be selectable: V-USB, LUFA or PJRC +#include $(TOP_DIR)/protocol/vusb.mk +include $(TOP_DIR)/common.mk +include $(TOP_DIR)/rules.mk |