diff options
Diffstat (limited to 'keyboards/ergodash/rules.mk')
| -rw-r--r-- | keyboards/ergodash/rules.mk | 41 |
1 files changed, 4 insertions, 37 deletions
diff --git a/keyboards/ergodash/rules.mk b/keyboards/ergodash/rules.mk index e25346dac..8be059d96 100644 --- a/keyboards/ergodash/rules.mk +++ b/keyboards/ergodash/rules.mk @@ -1,52 +1,21 @@ -SRC += matrix.c \ - i2c.c \ - split_util.c \ - serial.c \ - ssd1306.c - # MCU name -#MCU = at90usb1287 MCU = atmega32u4 # Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. F_CPU = 16000000 -# # LUFA specific # # Target architecture (see library "Board Types" documentation). ARCH = AVR8 # Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. F_USB = $(F_CPU) # Interrupt driven control endpoint task(+60) OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT # Bootloader -# This definition is optional, and if your keyboard supports multiple bootloaders of -# different sizes, comment this out, and the correct address will be loaded -# automatically (+60). See bootloader.mk for all options. BOOTLOADER = caterina # Build Options @@ -57,19 +26,17 @@ BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000) MOUSEKEY_ENABLE = no # Mouse keys(+4700) EXTRAKEY_ENABLE = yes # Audio control and System control(+450) CONSOLE_ENABLE = no # Console for debug(+400) -COMMAND_ENABLE = yes # Commands for debug and configuration +COMMAND_ENABLE = no # Commands for debug and configuration NKRO_ENABLE = no # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality MIDI_ENABLE = no # MIDI controls AUDIO_ENABLE = no # Audio output on port C6 UNICODE_ENABLE = no # Unicode BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID -RGBLIGHT_ENABLE = no # Enable WS2812 RGB underlight. -SUBPROJECT_rev1 = yes -USE_I2C = yes +RGBLIGHT_ENABLE = no # Enable WS2812 RGB underlight. # Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend -CUSTOM_MATRIX = yes +SPLIT_KEYBOARD = yes # Enables split keyboard support -DEFAULT_FOLDER = ergodash/rev2 +DEFAULT_FOLDER = ergodash/rev1 |