diff options
Diffstat (limited to 'keyboards/ergodone/rules.mk')
-rw-r--r-- | keyboards/ergodone/rules.mk | 80 |
1 files changed, 15 insertions, 65 deletions
diff --git a/keyboards/ergodone/rules.mk b/keyboards/ergodone/rules.mk index 6acfaf92e..4c2fcf159 100644 --- a/keyboards/ergodone/rules.mk +++ b/keyboards/ergodone/rules.mk @@ -1,71 +1,15 @@ -#---------------------------------------------------------------------------- -# On command line: -# -# make = Make software. -# -# make clean = Clean out built project files. -# -# That's pretty much all you need. To compile, always go make clean, -# followed by make. -# -# For advanced users only: -# make teensy = Download the hex file to the device, using teensy_loader_cli. -# (must have teensy_loader_cli installed). -# -#---------------------------------------------------------------------------- - -# # project specific files -SRC = \ - twimaster.c \ - matrix.c \ - expander.c \ - # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=4096 +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp +BOOTLOADER = caterina # Build Options # comment out to disable the options. @@ -92,4 +36,10 @@ SWAP_HANDS_ENABLE = no # Disable Onehand RGBLIGHT_ENABLE = no MIDI_ENABLE = no +# project specific files +SRC = \ + twimaster.c \ + matrix.c \ + expander.c \ + LAYOUTS = ergodox |