diff options
Diffstat (limited to 'keyboards/ergoinu')
| -rw-r--r-- | keyboards/ergoinu/matrix.c | 6 | ||||
| -rw-r--r-- | keyboards/ergoinu/rules.mk | 51 |
2 files changed, 9 insertions, 48 deletions
diff --git a/keyboards/ergoinu/matrix.c b/keyboards/ergoinu/matrix.c index 92c95e335..00914a257 100644 --- a/keyboards/ergoinu/matrix.c +++ b/keyboards/ergoinu/matrix.c @@ -174,18 +174,12 @@ uint8_t matrix_scan(void) { }else{ matrix_slave_scan(); -// if(serial_slave_DATA_CORRUPT()){ -// TXLED0; int offset = (isLeftHand) ? ROWS_PER_HAND : 0; for (int i = 0; i < ROWS_PER_HAND; ++i) { matrix[offset+i] = serial_master_buffer[i]; } -// }else{ -// TXLED1; -// } - matrix_scan_quantum(); } return 1; diff --git a/keyboards/ergoinu/rules.mk b/keyboards/ergoinu/rules.mk index de4bcad52..5c600bcd2 100644 --- a/keyboards/ergoinu/rules.mk +++ b/keyboards/ergoinu/rules.mk @@ -1,50 +1,16 @@ -SRC += matrix.c serial.c split_util.c - # MCU name -#MCU = at90usb1287 MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Bootloader -# This definition is optional, and if your keyboard supports multiple bootloaders of -# different sizes, comment this out, and the correct address will be loaded -# automatically (+60). See bootloader.mk for all options. +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = caterina -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - # Build Options # change to "no" to disable the options, or define them in the Makefile in # the appropriate keymap folder that will get included automatically @@ -67,6 +33,7 @@ USE_I2C = no # i2c is not supported SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend CUSTOM_MATRIX = yes +SRC += matrix.c serial.c split_util.c DEFAULT_FOLDER = ergoinu |