diff options
Diffstat (limited to 'keyboards/planck')
37 files changed, 2539 insertions, 97 deletions
diff --git a/keyboards/planck/Makefile b/keyboards/planck/Makefile index 23944f92e..7d49c5ef9 100644 --- a/keyboards/planck/Makefile +++ b/keyboards/planck/Makefile @@ -1,74 +1,5 @@ - SUBPROJECT_DEFAULT = rev4 -# MCU name -#MCU = at90usb1287 -MCU = atmega32u4 - -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=4096 - -# Build Options -# change to "no" to disable the options, or define them in the Makefile in -# the appropriate keymap folder that will get included automatically -# -BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000) -MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) -EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) -CONSOLE_ENABLE ?= no # Console for debug(+400) -COMMAND_ENABLE ?= yes # Commands for debug and configuration -NKRO_ENABLE ?= no # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work -BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality -MIDI_ENABLE ?= no # MIDI controls -AUDIO_ENABLE ?= no # Audio output on port C6 -UNICODE_ENABLE ?= no # Unicode -BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID -RGBLIGHT_ENABLE ?= no # Enable WS2812 RGB underlight. Do not enable this with audio at the same time. - -# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE -SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend - -ifndef QUANTUM_DIR +ifndef MAKEFILE_INCLUDED include ../../Makefile endif
\ No newline at end of file diff --git a/keyboards/planck/keymaps/bone2planck/keymap.c b/keyboards/planck/keymaps/bone2planck/keymap.c index 7db3197a7..69d164b8c 100644 --- a/keyboards/planck/keymaps/bone2planck/keymap.c +++ b/keyboards/planck/keymaps/bone2planck/keymap.c @@ -1,5 +1,4 @@ - -#include "planck.h" +#include "planck.h" #ifdef BACKLIGHT_ENABLE #include "backlight.h" #endif diff --git a/keyboards/planck/keymaps/callum/Makefile b/keyboards/planck/keymaps/callum/Makefile new file mode 100644 index 000000000..1d76966a6 --- /dev/null +++ b/keyboards/planck/keymaps/callum/Makefile @@ -0,0 +1,25 @@ + + +# Build Options +# change to "no" to disable the options, or define them in the Makefile in +# the appropriate keymap folder that will get included automatically +# +BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE = yes # Mouse keys(+4700) +EXTRAKEY_ENABLE = yes # Audio control and System control(+450) +CONSOLE_ENABLE = no # Console for debug(+400) +COMMAND_ENABLE = yes # Commands for debug and configuration +NKRO_ENABLE = yes # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality +MIDI_ENABLE = no # MIDI controls +AUDIO_ENABLE = no # Audio output on port C6 +UNICODE_ENABLE = no # Unicode +BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID +RGBLIGHT_ENABLE = no # Enable WS2812 RGB underlight. Do not enable this with audio at the same time. + +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend + +ifndef QUANTUM_DIR + include ../../../../Makefile +endif diff --git a/keyboards/planck/keymaps/callum/keymap.c b/keyboards/planck/keymaps/callum/keymap.c new file mode 100644 index 000000000..ed187df1d --- /dev/null +++ b/keyboards/planck/keymaps/callum/keymap.c @@ -0,0 +1,138 @@ +#include "planck.h" +#include "action_layer.h" +#ifdef AUDIO_ENABLE + #include "audio.h" +#endif +#include "eeconfig.h" + +extern keymap_config_t keymap_config; + +// Each layer gets a name for readability, which is then used in the keymap matrix below. +// The underscores don't mean anything - you can have a layer called STUFF or any other name. +// Layer names don't all need to be of the same length, obviously, and you can also skip them +// entirely and just use numbers. +#define _BASE 0 +#define _MOVE 1 +#define _SYMB 2 +#define _FUNC 3 + +enum planck_keycodes { + BASE = SAFE_RANGE, + MOVE, + SYMB, + FUNC +}; + +// Fillers to make layering more clear +#define _______ KC_TRNS +#define XXXXXXX KC_NO + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { + +/* BASE + * ,-----------------------------------------------------------------------------------. + * | Tab | Q | W | F | P | G | J | L | U | Y | ; | - | + * |------+------+------+------+------+-------------+------+------+------+------+------| + * | Bksp | A | R | S | T | D | H | N | E | I | O | " | + * |------+------+------+------+------+------|------+------+------+------+------+------| + * | Shift| Z | X | C | V | B | K | M | , | . | / |Shift | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | Func | GUI | Alt | Ctrl | Symb |Enter |Space | Move | GUI | Alt | Ctrl |Caps | + * `-----------------------------------------------------------------------------------' + */ +[_BASE] = { + {KC_TAB, KC_Q, KC_W, KC_F, KC_P, KC_G, KC_J, KC_L, KC_U, KC_Y, KC_SCLN, KC_MINS}, + {KC_BSPC, KC_A, KC_R, KC_S, KC_T, KC_D, KC_H, KC_N, KC_E, KC_I, KC_O, KC_QUOT}, + {KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_K, KC_M, KC_COMM, KC_DOT, KC_SLSH, KC_RSFT}, + {FUNC, KC_LGUI, KC_LALT, KC_LCTL, SYMB, KC_ENT, KC_SPC, MOVE, KC_RGUI, KC_RALT, KC_RCTL, KC_CAPS} +}, + +/* MOVE + * ,-----------------------------------------------------------------------------------. + * | Esc | | Home | Up | End | | | Home | Up | End | | Esc | + * |------+------+------+------+------+-------------+------+------+------+------+------| + * | Del | | Left | Down |Right | | | Left | Down |Right | | Del | + * |------+------+------+------+------+------|------+------+------+------+------+------| + * | | | |Pg Up |Pg Dn | | |Pg Dn |Pg Up | | | | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | | | | | | | | | | | | | + * `-----------------------------------------------------------------------------------' + */ +[_MOVE] = { + {KC_ESC, _______, KC_HOME, KC_UP, KC_END, _______, _______, KC_HOME, KC_UP, KC_END, _______, KC_ESC}, + {KC_DEL, _______, KC_LEFT, KC_DOWN, KC_RGHT, _______, _______, KC_LEFT, KC_DOWN, KC_RGHT, _______, KC_DEL}, + {_______, _______, _______, KC_PGUP, KC_PGDN, _______, _______, KC_PGDN, KC_PGUP, _______, _______, _______}, + {_______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______} +}, + +/* SYMB + * ,-----------------------------------------------------------------------------------. + * | Esc | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 0 | Esc | + * |-----------------------------------------------------------------------------------. + * | Del | ! | @ | # | $ | % | ^ | & | * | ( | ) | Del | + * |------+------+------+------+------+-------------+------+------+------+------+------| + * | | ~ | ` | + | = | | | \ | [ | ] | { | } | | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | | | | | | | | | | | | | + * `-----------------------------------------------------------------------------------' + */ +[_SYMB] = { + {KC_ESC, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_ESC }, + {KC_DEL, KC_EXLM, KC_AT, KC_HASH, KC_DLR, KC_PERC, KC_CIRC, KC_AMPR, KC_ASTR, KC_LPRN, KC_RPRN, KC_DEL }, + {_______, KC_TILD, KC_GRV, KC_PLUS, KC_EQL, KC_PIPE, KC_BSLS, KC_LBRC, KC_RBRC, KC_LCBR, KC_RCBR, _______}, + {_______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______} +}, + +/* FUNC + * ,-----------------------------------------------------------------------------------. + * | F12 | F1 | F2 | F3 | F4 | F5 | F6 | F7 | F8 | F9 | F10 | F11 | + * |-----------------------------------------------------------------------------------. + * | | Play | Prev | Next | BL+ | | | | | | | | + * |------+------+------+------+------+------|------+------+------+------+------+------| + * | | Mute | Vol- | Vol+ | BL- | | | | | | | | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | | | | | | | | | | | |Reset | + * `-----------------------------------------------------------------------------------' + */ +[_FUNC] = { + {KC_F12, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11 }, + {_______, KC_MPLY, KC_MPRV, KC_MNXT, KC_PAUS, _______, _______, _______, _______, _______, _______, _______}, + {_______, KC_MUTE, KC_VOLD, KC_VOLU, KC_SLCK, _______, _______, _______, _______, _______, _______, _______}, + {_______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, RESET } +} + +}; + +bool process_record_user(uint16_t keycode, keyrecord_t *record) { + switch (keycode) { + case MOVE: + if (record->event.pressed) { + layer_on(_MOVE); + update_tri_layer(_MOVE, _SYMB, _FUNC); + } else { + layer_off(_MOVE); + update_tri_layer(_MOVE, _SYMB, _FUNC); + } + return false; + break; + case SYMB: + if (record->event.pressed) { + layer_on(_SYMB); + update_tri_layer(_MOVE, _SYMB, _FUNC); + } else { + layer_off(_SYMB); + update_tri_layer(_MOVE, _SYMB, _FUNC); + } + return false; + break; + case FUNC: + if (record->event.pressed) { + layer_on(_FUNC); + } else { + layer_off(_FUNC); + } + return false; + break; + } + return true; +} diff --git a/keyboards/planck/keymaps/callum/readme.md b/keyboards/planck/keymaps/callum/readme.md new file mode 100644 index 000000000..030def7f7 --- /dev/null +++ b/keyboards/planck/keymaps/callum/readme.md @@ -0,0 +1,48 @@ +# callum’s planck layout + +This is a layout for the grid planck, built with a few ideals in mind. These ideals are just my opinion mind! The great thing about *qmk* is that we can all afford to have different opinions about what makes a good layout: + +- Minimal response times should be maintained. i.e. keys that react differently depending on whether they are tapped or held, keys that react differently if they are double tapped, etc. should be avoided --- since they inevitably send their keycode later than a normal key, interrupting the immediate feedback from the screen. Therefore we restrict ourselves to chording. +- The hands should never need to leave the home position. The usual culprit for this is the arrow cluster, so the arrow cluster should be as close to home as possible. +- There should be two of every modifier (one on each side), since otherwise certain long key combinations become hard to make. +- Backspace should be in the “capslock position” as God intended. +- The keyboard should be usable without any firmware changes on any operating system. In my case that means it should work on *Windows* and *Linux* without any software modifications, while I can change the behaviour slightly on *macOS* in software since that’s my home OS. The images reflect the intended use on *macOS* **after** minor software tweaks; which will be noted. + +We have four layers. A `BASE` layer, in colemak; a `MOVE` layer, with an arrow cluster etc, a `SYMB` layer, with numbers and symbols; and a `FUNC` layer, with function keys and media keys. + +## The `BASE` layer + + +This is the default layer; in [colemak](https://colemak.com). `esc` and `del` are conspicuously absent but are especially easy to reach from either of the other main layers (see below). The `backspace` location is standard colemak. The `caps` key is still on the `BASE` layer but only because I don’t really use the bottom corners so there’s nothing else I would rather put there. Having `enter` on a thumb means I can still have `quote` immediately to the right of `O`, something that would have annoyed me endlessly otherwise. `minus` is in the upper right because I had an extra space and it’s probably my next most used key that didn’t yet have a home. + +The `MOVE` and `SYMB` layers are reached by holding down the `move` and `symb` keys respectively. The `FUNC` layer is reached by holding down both the `move` and `symb` keys simultaneosly, *or* by holding down the `fn` key. The intended use is that whenever both hands are on the keyboard, the former method is used, and the latter is only used when, for example, reaching over to the keyboard with one hand to access the media controls. + +The `ctrl`, `alt`, `cmd` cluster is asymmetric around the centre so that at least one of each of the modifiers can be reached with the thumbs. The intended use is to always hit the left `cmd` and the right `ctrl`, unless an awkward key combination dictates otherwise. + +In firmware `ctrl` and `cmd`/`GUI` are swapped with respect to the image above --- I swap them to the illustrated location when using *macOS* and leave them be for *Windows* and *Linux*. (so that `cmd-z,x,c,v,...` becomes `ctrl-z,x,c,v,...` saving me some confusion) + +## The `MOVE` layer + + +This is fairly self explanatory. I almost exclusively use the right hand cluster so that movement is a one handed affair, but the left hand cluster is there if it’s needed. + +On *macOS* I recommend using [Karabiner](https://pqrs.org/osx/karabiner/) and ticking *Use PC Style Home/End #2* and *Use PC Style PageUp/PageDown* so that `home` and `end` jump you to the beginning and end of the line respectively and so that `pg up` and `pg dn` move the cursor instead of just scrolling. + +None of the modifiers are overwritten so that `shift-alt-arrows` etc work as expected. + +## The `SYMB` layer + + +The symbol layer has all the numbers and their usual corresponding symbols in the first two rows, with the symbols on the home row since I use them more frequently than the numbers. The third row contains all the remaining symbols, arranged roughly so that the most used symbols are accessible with the strongest fingers. + +`esc` and `del` are repeated here since I wanted to be able to reach either, one handed, with either hand. + +Again none of the modifiers are overwritten so that shortcuts involving numbers or symbols work as expected. + +## The `FUNC` layer + + +The only thing of note here is that `bl+` and `bl-` are short for *backlight up* and *backlight down* respectively, and in firmware are actually `KC_PAUS` and `KC_SLCK` respectively, since *macOS* interprets these as the backlight keys. + +## Other changes from the default +I have LEDs and sound disabled, simply because I have no need of them.
\ No newline at end of file diff --git a/keyboards/planck/keymaps/cbbrowne/keymap.c b/keyboards/planck/keymaps/cbbrowne/keymap.c index 14a5be170..70eaefb7b 100644 --- a/keyboards/planck/keymaps/cbbrowne/keymap.c +++ b/keyboards/planck/keymaps/cbbrowne/keymap.c @@ -4,6 +4,7 @@ #endif #include "config.h" #include "quantum.h" +#include "version.h" /* Each layer is given a name to aid in readability, which is then used in the keymap matrix below. The underscores do not denote diff --git a/keyboards/planck/keymaps/circuit/Makefile b/keyboards/planck/keymaps/circuit/Makefile new file mode 100644 index 000000000..1ed0ff956 --- /dev/null +++ b/keyboards/planck/keymaps/circuit/Makefile @@ -0,0 +1,25 @@ + +# Build Options +# change to "no" to disable the options, or define them in the makefile.mk in +# the appropriate keymap folder that will get included automatically +# +BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE = no # Mouse keys(+4700) +EXTRAKEY_ENABLE = yes # Audio control and System control(+450) +CONSOLE_ENABLE = no # Console for debug(+400) +COMMAND_ENABLE = yes # Commands for debug and configuration +NKRO_ENABLE = yes # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality +MIDI_ENABLE = no # MIDI controls +AUDIO_ENABLE = no # Audio output on port C6 +UNICODE_ENABLE = no # Unicode +BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID +RGBLIGHT_ENABLE = no # Enable WS2812 RGB underlight. Do not enable this with audio at the same time. +TAP_DANCE_ENABLE = yes # Enables the double-tap functionality of keys + +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend + +ifndef QUANTUM_DIR + include ../../../../Makefile +endif diff --git a/keyboards/planck/keymaps/circuit/Readme.md b/keyboards/planck/keymaps/circuit/Readme.md new file mode 100644 index 000000000..cbdf5de4e --- /dev/null +++ b/keyboards/planck/keymaps/circuit/Readme.md @@ -0,0 +1,44 @@ +##Design goals: +1. Arrow keys always available. +2. As close to a to my US layout 107-key QWERTY keyboard as I could manage, (i.e. as few arbitrary decisions as possible). +3. Togglable DVORAK keyboard. +4. most frequently used things in the easiest to reach places. +5. Ability to game on it, just for fun. + +My layout differs from most in the placement the ARROW keys, `ESC`, VOL keys, use of double-tap `CAPS`, and the GAME LOCK function. + +I put the layer buttons in the usual spots. I originally wanted only function/symbols layer, but that proved detrimental. I use some timed press actions to save some space, but this has been accounted for, (see GAME LOCK below). I'm not fully satisfied with the current product (see NOTES below), so it may change in the future. + +##Effective layers: +* Default later is obviously your letters and modifiers. +* Lower layer [NUMBER] is your numbers and punctuation. +* Upper layer [ACTION] is your symbols and actions. +* Function layer is the infrequently used function keys, layout toggle, game lock, and reset. + +There is also a toggle for the DVORAK/QWERTY layers, but in normal typing this is not of concern. + +###Special keys: +* `RSHFT` and `ENTER` are combined. Tap once for `ENTER` and hold for `RSHFT`. `ENTER` will be registered on release if released within 200 ms, else `RSHFT` is registered starting at 201 ms until release. +* If for some reason, this interferes with the normal usage of the `ENTER` key in any way, (some problem that may never happen), I have added a regular non-modified `ENTER` key on the same key in the [ACTION] layer. +* `LSHFT` and `CAPS` are also combined. The key works like a normal `LSHFT` unless double-tapped, in which case it counts as `CAPS`. This functionality unfortunately delays all key presses by at most 200 ms, but I have added ways to disable this both temporarily or permanently, described below. +* A failsafe `CAPS` key is on the same key in the [ACTION] layer. +* There are `UNDO`, `CUT`, `COPY`, and `PASTE` keys. This was intended to be a universal way to use these commands since in macOS cut is `⌘ + C` but in Windows it is `⌃ + C`. Unfortunately these special keys only work in Windows. ¯\\\_(ツ)\_/¯ + +##Game lock: +**TL;DR** the game lock toggle disables the double-tap `CAPS`, and disables `GUI` keys (WINDOWS key). + +I wished for this keyboard to be fully usable in the most demanding of games. The most demanding game I know of is ARMA 3 which has a binding to practically every individual key of a 107-key keyboard. This means I need to have pretty much every key possible somewhere. I also wanted the keyboard to be responsive in games for every critical keypress. This means having a way to disable features that introduce an inherent delay to registering keys, such as double-tap. + +I do not expect to see this used by the pros, but I enjoyed making it. As for use in ARMA 3, I got a little ways into the APEX campaign, but I found a few flaws. For Example, I cannot enable my HUD GPS since that requires `RCTRL`+`M` but `RCTRL` is not bound. The obvious fix is to rebind the action to a new key, but I still take this as a shortcoming of my layout. + +###If you wish to disable double-tap +####Disable it temporarily +Turn on the game lock. While on, it registers as normal `LSHFT` and has no delay. Whether in game mode or not, `CAPS` is on the same key in the [ACTION] layer. + +####Disable it permanently +Open the `Makefile` and set `TAP_DANCE_ENABLE = no`. I wrote the layout to compensate for this change, and no further changes to the code should be necessary. Whether or not it's disabled, `CAPS` is on the same key in the [ACTION] layer. + +##Notes: +* `ALT` and `GUI` are reversed compared to the normal US layout. I will also be using my Planck on my mac, and that's the standard in the Apple ecosystem. I may add a special compiler flag in the future to swap the two. +* The DVORAK `Z` key is to the right of the `S` key instead of under it as part of a compromise I made to keep the ARROW keys available on the default layer. I prioritize the ARROW keys, so the DVORAK layout is the one to suffer. +* I also support the little tones that the default Planck layout features, identical to them too, (minus those for layouts I don't support). To enable it, open the `Makefile` and set `AUDIO_ENABLE = yes`. diff --git a/keyboards/planck/keymaps/circuit/config.h b/keyboards/planck/keymaps/circuit/config.h new file mode 100644 index 000000000..22244f4a7 --- /dev/null +++ b/keyboards/planck/keymaps/circuit/config.h @@ -0,0 +1,91 @@ +/* +Copyright 2012 Jun Wako <wakojun@gmail.com> + +This program is free software: you can redistribute it and/or modify +it under the terms of the GNU General Public License as published by +the Free Software Foundation, either version 2 of the License, or +(at your option) any later version. + +This program is distributed in the hope that it will be useful, +but WITHOUT ANY WARRANTY; without even the implied warranty of +MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +GNU General Public License for more details. + +You should have received a copy of the GNU General Public License +along with this program. If not, see <http://www.gnu.org/licenses/>. +*/ + +#ifndef CONFIG_H +#define CONFIG_H + +#include "config_common.h" + +/* Tap-dance interval definition */ +#define TAPPING_TERM 200 + +/* USB Device descriptor parameter */ +#define VENDOR_ID 0xFEED +#define PRODUCT_ID 0x6060 +#define MANUFACTURER Ortholinear Keyboards +#define PRODUCT The Planck Keyboard +#define DESCRIPTION A compact ortholinear keyboard + +/* key matrix size */ +#define MATRIX_ROWS 4 +#define MATRIX_COLS 12 + +/* Planck PCB default pin-out */ +#define MATRIX_ROW_PINS { D0, D5, B5, B6 } +#define MATRIX_COL_PINS { F1, F0, B0, C7, F4, F5, F6, F7, D4, D6, B4, D7 } +#define UNUSED_PINS + +#define BACKLIGHT_PIN B7 + +/* COL2ROW or ROW2COL */ +#define DIODE_DIRECTION COL2ROW + +/* define if matrix has ghost */ +//#define MATRIX_HAS_GHOST + +/* number of backlight levels */ +#define BACKLIGHT_LEVELS 3 + +/* Set 0 if debouncing isn't needed */ +#define DEBOUNCING_DELAY 5 + +/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ +#define LOCKING_SUPPORT_ENABLE +/* Locking resynchronize hack */ +#define LOCKING_RESYNC_ENABLE + +/* key combination for command */ +#define IS_COMMAND() ( \ + keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \ +) + +/* + * Feature disable options + * These options are also useful to firmware size reduction. + */ + +/* disable debug print */ +//#define NO_DEBUG + +/* disable print */ +//#define NO_PRINT + +/* disable action features */ +//#define NO_ACTION_LAYER +//#define NO_ACTION_TAPPING +//#define NO_ACTION_ONESHOT +//#define NO_ACTION_MACRO +//#define NO_ACTION_FUNCTION + +#ifdef SUBPROJECT_rev3 + #include "rev3/config.h" +#endif +#ifdef SUBPROJECT_rev4 + #include "rev4/config.h" +#endif + +#endif diff --git a/keyboards/planck/keymaps/circuit/keyboard-layout.png b/keyboards/planck/keymaps/circuit/keyboard-layout.png Binary files differnew file mode 100644 index 000000000..e9296a6d9 --- /dev/null +++ b/keyboards/planck/keymaps/circuit/keyboard-layout.png diff --git a/keyboards/planck/keymaps/circuit/keymap.c b/keyboards/planck/keymaps/circuit/keymap.c new file mode 100644 index 000000000..63e01f389 --- /dev/null +++ b/keyboards/planck/keymaps/circuit/keymap.c @@ -0,0 +1,258 @@ +// Layout picture at http://www.keyboard-layout-editor.com/#/gists/125febfad6960add078e6f14256539b6 + +#include "planck.h" +#include "action_layer.h" +#ifdef AUDIO_ENABLE +#include "audio.h" +#endif +#include "eeconfig.h" + +extern keymap_config_t keymap_config; + +// Each layer gets a name for readability, which is then used in the keymap matrix below. +// The underscores don't mean anything - you can have a layer called STUFF or any other name. +// Layer names don't all need to be of the same length, obviously, and you can also skip them +// entirely and just use numbers. +#define _QWERTY 0 +#define _DVORAK 1 +#define _LOCKED 2 +#define _NUMBER 3 +#define _ACTION 4 +#define _FUNCTN 5 + +enum planck_keycodes { + QWERTY = SAFE_RANGE, + DVORAK, + NUMBER, + ACTION +}; + +// Key code names +#define SFT_ENT FUNC(0) // Tap for enter, hold for right shift +#define LOCK FUNC(1) +#define KC_PSTE KC_PASTE +#define _______ KC_TRNS +#define XXXXXXX KC_NO + +#ifdef TAP_DANCE_ENABLE +#define SFT_CAP TD(0) // Left shift, double tap for caps +#endif +#ifndef TAP_DANCE_ENABLE +#define SFT_CAP KC_LSFT // Regular left shift +#endif + +// Tap Dance Definitions +#ifdef TAP_DANCE_ENABLE +qk_tap_dance_action_t tap_dance_actions[] = { + [0] = ACTION_TAP_DANCE_DOUBLE(KC_LSFT, KC_CAPS) +}; +#endif + +// Function definitions +const uint16_t PROGMEM fn_actions[] = { + [0] = ACTION_MODS_TAP_KEY(MOD_RSFT, KC_ENT), + [1] = ACTION_LAYER_TOGGLE(_LOCKED) +}; + +// Layout definitions +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { + +/* QWERTY + * ,-----------------------------------------------------------------------------------. + * | Esc | Q | W | E | R | T | Y | U | I | O | P | BKSP | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | Tab | A | S | D | F | G | H | J | K | L | ; | ' | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * |*Shift| Z | X | C | V | B | N | M | , | . | Up |SftEnt| + * |------+------+------+------+------+-------------+------+------+------+------+------| + * | Ctrl | Alt | Cmd | Vol- | ACTN | Space | NUMS | Vol+ | Left | Down | Left | + * `-----------------------------------------------------------------------------------' + */ +[_QWERTY] = { + {KC_ESC, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_BSPC}, + {KC_TAB, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT}, + {SFT_CAP, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_UP, SFT_ENT}, + {KC_LCTL, KC_LALT, KC_LGUI, KC_VOLD, ACTION, KC_SPC, KC_SPC, NUMBER, KC_VOLU, KC_LEFT, KC_DOWN, KC_RGHT} +}, + +/* DVORAK + * ,-----------------------------------------------------------------------------------. + * | | ' | , | . | P | Y | F | G | C | R | L | | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | | A | O | E | U | I | D | H | T | N | S | Z | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | | ; | Q | J | K | X | B | M | W | V | | | + * |------+------+------+------+------+-------------+------+------+------+------+------| + * | | | | | | | | | | | | + * `-----------------------------------------------------------------------------------' + */ +[_DVORAK] = { + {_______, KC_QUOT, KC_COMM, KC_DOT, KC_P, KC_Y, KC_F, KC_G, KC_C, KC_R, KC_L, _______}, + {_______, KC_A, KC_O, KC_E, KC_U, KC_I, KC_D, KC_H, KC_T, KC_N, KC_S, KC_Z }, + {_______, KC_SCLN, KC_Q, KC_J, KC_K, KC_X, KC_B, KC_M, KC_W, KC_V, _______, _______}, + {_______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______} +}, + +/* LOCK + * ,-----------------------------------------------------------------------------------. + * | | | | | | | | | | | | | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | | | | | | | | | | | | | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | Shift| | | | | | | | | | | | + * |------+------+------+------+------+-------------+------+------+------+------+------| + * | | | NULL | | | | | | | | | + * `-----------------------------------------------------------------------------------' + */ +[_LOCKED] = { + {_______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______}, + {_______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______}, + {KC_LSFT, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______}, + {_______, _______, XXXXXXX, _______, _______, _______, _______, _______, _______, _______, _______, _______} +}, + +/* NUMBERS + * ,-----------------------------------------------------------------------------------. + * | | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 0 | | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | | ~ | NULL | NULL | NULL | | | _ | + | { | } | ? | / | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | | ` | NULL | NULL | NULL | \ | - | = | [ | ] | | | + * |------+------+------+------+------+-------------+------+------+------+------+------| + * | | | | | | NULL | | | | | | + * `-----------------------------------------------------------------------------------' + */ +[_NUMBER] = { + {_______, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, _______}, + {_______, KC_TILD, XXXXXXX, XXXXXXX, XXXXXXX, KC_PIPE, KC_UNDS, KC_PLUS, KC_LCBR, KC_RCBR, KC_QUES, KC_SLSH}, + {_______, KC_GRV, XXXXXXX, XXXXXXX, XXXXXXX, KC_BSLS, KC_MINS, KC_EQL, KC_LBRC, KC_RBRC, _______, _______}, + {_______, _______, _______, _______, _______, XXXXXXX, XXXXXXX, _______, _______, _______, _______, _______} +}, + +/* ACTIONS + * ,-----------------------------------------------------------------------------------. + * | | ! | @ | # | $ | % | ^ | & | * | ( | ) | Del | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | | NULL | NULL | NULL | NULL | NULL | NULL | NULL | NULL | NULL | NULL | NULL | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | CAPS | Undo | Cut | Copy | Paste| NULL | NULL | NULL | NULL | NULL | PgUp | Enter| + * |------+------+------+------+------+-------------+------+------+------+------+------| + * | | | | Mute | | NULL | | NULL | Home | PgDn | End | + * `-----------------------------------------------------------------------------------' + */ +[_ACTION] = { + {_______, KC_EXLM, KC_AT, KC_HASH, KC_DLR, KC_PERC, KC_CIRC, KC_AMPR, KC_ASTR, KC_LPRN, KC_RPRN, KC_DEL }, + {_______, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX}, + {KC_CAPS, KC_UNDO, KC_CUT, KC_COPY, KC_PSTE, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, KC_PGUP, KC_ENT }, + {_______, _______, _______, KC_MUTE, _______, XXXXXXX, XXXXXXX, _______, XXXXXXX, KC_HOME, KC_PGDN, KC_END } +}, + +/* FUNCTIONS + * ,-----------------------------------------------------------------------------------. + * | F1 | F2 | F3 | F4 | F5 | F6 | F7 | F8 | F9 | F10 | F11 | F12 | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | F13 | F14 | F15 | F16 | F17 | F18 | F19 | F20 | F21 | F22 | F23 | F24 | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | NULL | NULL | NULL | NULL | NULL |QWERTY|DVORAK| NULL | NULL | NULL | NULL | NULL | + * |------+------+------+------+------+-------------+------+------+------+------+------| + * | Reset| NULL | Lock | NULL | | NULL | | NULL | NULL | NULL | NULL | + * `-----------------------------------------------------------------------------------' + */ +[_FUNCTN] = { + {KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12 }, + {KC_F13, KC_F14, KC_F15, KC_F16, KC_F17, KC_F18, KC_F19, KC_F20, KC_F21, KC_F22, KC_F23, KC_F24 }, + {XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, QWERTY, DVORAK, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX}, + {RESET, XXXXXXX, LOCK, XXXXXXX, _______, XXXXXXX, XXXXXXX, _______, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX} +} + +}; + +#ifdef AUDIO_ENABLE +float tone_startup[][2] = SONG(STARTUP_SOUND); +float tone_qwerty[][2] = SONG(QWERTY_SOUND); +float tone_dvorak[][2] = SONG(DVORAK_SOUND); +float music_scale[][2] = SONG(MUSIC_SCALE_SOUND); +float tone_goodbye[][2] = SONG(GOODBYE_SOUND); +#endif + + +bool process_record_user(uint16_t keycode, keyrecord_t *record) { + switch (keycode) { + case QWERTY: + if (record->event.pressed) { + if (IS_LAYER_ON(_DVORAK)) { +#ifdef AUDIO_ENABLE + PLAY_NOTE_ARRAY(tone_qwerty, false, 0); +#endif + layer_off(_DVORAK); + } + } + return false; + break; + case DVORAK: + if (record->event.pressed) { + if (!IS_LAYER_ON(_DVORAK)) { +#ifdef AUDIO_ENABLE + PLAY_NOTE_ARRAY(tone_dvorak, false, 0); +#endif + layer_on(_DVORAK); + } + } + return false; + break; + case NUMBER: + if (record->event.pressed) { + layer_on(_NUMBER); + update_tri_layer(_NUMBER, _ACTION, _FUNCTN); + } else { + layer_off(_NUMBER); + update_tri_layer(_NUMBER, _ACTION, _FUNCTN); + } + return false; + break; + case ACTION: + if (record->event.pressed) { + layer_on(_ACTION); + update_tri_layer(_NUMBER, _ACTION, _FUNCTN); + } else { + layer_off(_ACTION); + update_tri_layer(_NUMBER, _ACTION, _FUNCTN); + } + return false; + break; + } + return true; +} + +void matrix_init_user(void) { +#ifdef AUDIO_ENABLE + startup_user(); +#endif +} + +#ifdef AUDIO_ENABLE + +void startup_user() +{ + _delay_ms(20); // gets rid of tick + PLAY_NOTE_ARRAY(tone_startup, false, 0); +} + +void shutdown_user() +{ + PLAY_NOTE_ARRAY(tone_goodbye, false, 0); + _delay_ms(150); + stop_all_notes(); +} + +void music_on_user(void) +{ + music_scale_user(); +} + +void music_scale_user(void) +{ + PLAY_NOTE_ARRAY(music_scale, false, 0); +} + +#endif diff --git a/keyboards/planck/keymaps/dbroqua/keymap.c b/keyboards/planck/keymaps/dbroqua/keymap.c new file mode 100644 index 000000000..33929cb3a --- /dev/null +++ b/keyboards/planck/keymaps/dbroqua/keymap.c @@ -0,0 +1,234 @@ +// This is the canonical layout file for the Quantum project. If you want to add another keyboard, +// this is the style you want to emulate. + +#include "planck.h" +#include "action_layer.h" +#ifdef AUDIO_ENABLE + #include "audio.h" +#endif +#include "eeconfig.h" + +extern keymap_config_t keymap_config; + +// Each layer gets a name for readability, which is then used in the keymap matrix below. +// The underscores don't mean anything - you can have a layer called STUFF or any other name. +// Layer names don't all need to be of the same length, obviously, and you can also skip them +// entirely and just use numbers. +#define _QWERTY 0 +#define _LOWER 1 +#define _RAISE 2 +#define _MULTIMEDIA 3 +#define _ADJUST 4 + +enum planck_keycodes { + QWERTY = SAFE_RANGE, + LOWER, + RAISE, + BACKLIT +}; + +// Fillers to make layering more clear +#define _______ KC_TRNS +#define XXXXXXX KC_NO + +// Func macro definitions. +#define SFT_TAB FUNC(0) // Tap for Enter, hold for Shift + +// Enable these functions using FUNC(n) macro. +const uint16_t PROGMEM fn_actions[] = { + [0] = ACTION_LAYER_TAP_KEY(_MULTIMEDIA, KC_TAB) + }; + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { + +/* Qwerty + * ,-----------------------------------------------------------------------------------. + * | Esc | Q | W | E | R | T | Y | U | I | O | P | Bksp | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | Tab | A | S | D | F | G | H | J | K | L | ; | " | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | Shift| Z | X | C | V | B | N | M | , | . | / |Enter | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | Ctrl | GUI | AltGr| Alt | Lower| Space | Raise| Left | Down | Up |Right | + * `-----------------------------------------------------------------------------------' + */ +[_QWERTY] = { + {KC_ESC, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_BSPC}, + {SFT_TAB, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT}, + {KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, KC_ENT }, + {KC_LCTL, KC_LGUI, KC_RALT, KC_LALT, LOWER, KC_SPC, KC_SPC, RAISE, KC_LEFT, KC_DOWN, KC_UP, KC_RIGHT} +}, + +/* Lower + * ,-----------------------------------------------------------------------------------. + * | | | | | | | | | | | ( | ) | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | Brite| | | | | | | | | | { | } | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | | | | | | | | | | | [ | ] | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | | | | | | | | Home | PgDwn| PgUp | End | + * `-----------------------------------------------------------------------------------' + */ +[_LOWER] = { + {_______, _______, _______, _______, _______, _______, _______, _______, _______, _______, KC_LPRN, KC_RPRN}, + {BACKLIT, _______, _______, _______, _______, _______, _______, _______, _______, _______, KC_LCBR, KC_RCBR}, + {_______, _______, _______, _______, _______, _______, _______, _______, _______, _______, KC_LBRC, KC_RBRC}, + {_______, _______, _______, _______, _______, _______, _______, _______, KC_HOME, KC_PGDN, KC_PGUP, KC_END} +}, + +/* Raise + * ,-----------------------------------------------------------------------------------. + * | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 | - | = | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | | | | | | | | | | | | ` | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | | | | | | | | | | | \ | | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | | | | | | | | | | | | + * `-----------------------------------------------------------------------------------' + */ +[_RAISE] = { + {KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_EQL}, + {_______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, KC_GRV}, + {_______, _______, _______, _______, _______, _______, _______, _______, _______, _______, KC_BSLS, _______}, + {_______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______} +}, + +/* _MULTIMEDIA + * ,-----------------------------------------------------------------------------------. + * | F1 | F2 | F3 | F4 | F5 | F6 | F7 | F8 | F9 | F10 | F11 | F12 | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | | | | | | | | Psc | | | | | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | | | | | | Mute | Vol+ | Vol- | | | |Insert| + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | | | | | | | | Prev | Play | Next | Del | + * `-----------------------------------------------------------------------------------' + */ +[_MULTIMEDIA] = { + {KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12}, + {_______, _______, _______, _______, _______, _______, _______, KC_PSCR, _______, _______, _______, _______}, + {_______, _______, _______, _______, _______, KC_MUTE, KC_VOLU, KC_VOLD, _______, _______, _______, KC_INS}, + {_______, _______, _______, _______, _______, _______, _______, _______, KC_MPRV, KC_MPLY, KC_MNXT, KC_DEL} +}, + + +/* Adjust (Lower + Raise) + * ,-----------------------------------------------------------------------------------. + * | | Reset| | | | | | | | | | Del | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | | | |Aud on|Audoff|AGnorm|AGswap|Qwerty| | | | | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | |Voice-|Voice+|Mus on|Musoff|MIDIon|MIDIof| | | | | | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | | | | | | | | | | | | + * `-----------------------------------------------------------------------------------' + */ +[_ADJUST] = { + {_______, RESET, _______, _______, _______, _______, _______, _______, _______, _______, _______, KC_DEL}, + {_______, _______, _______, AU_ON, AU_OFF, AG_NORM, AG_SWAP, QWERTY, _______, _______, _______, _______}, + {_______, MUV_DE, MUV_IN, MU_ON, MU_OFF, MI_ON, MI_OFF, _______, _______, _______, _______, _______}, + {_______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______} +} + + +}; + +#ifdef AUDIO_ENABLE + +float tone_startup[][2] = SONG(STARTUP_SOUND); +float tone_qwerty[][2] = SONG(QWERTY_SOUND); +float tone_dvorak[][2] = SONG(DVORAK_SOUND); +float tone_colemak[][2] = SONG(COLEMAK_SOUND); +float tone_plover[][2] = SONG(PLOVER_SOUND); +float tone_plover_gb[][2] = SONG(PLOVER_GOODBYE_SOUND); +float music_scale[][2] = SONG(MUSIC_SCALE_SOUND); + +float tone_goodbye[][2] = SONG(GOODBYE_SOUND); +#endif + + +void persistant_default_layer_set(uint16_t default_layer) { + eeconfig_update_default_layer(default_layer); + default_layer_set(default_layer); +} + +bool process_record_user(uint16_t keycode, keyrecord_t *record) { + switch (keycode) { + case QWERTY: + if (record->event.pressed) { + #ifdef AUDIO_ENABLE + PLAY_NOTE_ARRAY(tone_qwerty, false, 0); + #endif + persistant_default_layer_set(1UL<<_QWERTY); + } + return false; + break; + case LOWER: + if (record->event.pressed) { + layer_on(_LOWER); + update_tri_layer(_LOWER, _RAISE, _ADJUST); + } else { + layer_off(_LOWER); + update_tri_layer(_LOWER, _RAISE, _ADJUST); + } + return false; + break; + case RAISE: + if (record->event.pressed) { + layer_on(_RAISE); + update_tri_layer(_LOWER, _RAISE, _ADJUST); + } else { + layer_off(_RAISE); + update_tri_layer(_LOWER, _RAISE, _ADJUST); + } + return false; + break; + case BACKLIT: + if (record->event.pressed) { + register_code(KC_RSFT); + #ifdef BACKLIGHT_ENABLE + backlight_step(); + #endif + } else { + unregister_code(KC_RSFT); + } + return false; + break; + } + return true; +} + +void matrix_init_user(void) { + #ifdef AUDIO_ENABLE + startup_user(); + #endif +} + +#ifdef AUDIO_ENABLE + +void startup_user() +{ + _delay_ms(20); // gets rid of tick + PLAY_NOTE_ARRAY(tone_startup, false, 0); +} + +void shutdown_user() +{ + PLAY_NOTE_ARRAY(tone_goodbye, false, 0); + _delay_ms(150); + stop_all_notes(); +} + +void music_on_user(void) +{ + music_scale_user(); +} + +void music_scale_user(void) +{ + PLAY_NOTE_ARRAY(music_scale, false, 0); +} + +#endif
\ No newline at end of file diff --git a/keyboards/planck/keymaps/dbroqua/layout.png b/keyboards/planck/keymaps/dbroqua/layout.png Binary files differnew file mode 100644 index 000000000..37b74cdc5 --- /dev/null +++ b/keyboards/planck/keymaps/dbroqua/layout.png diff --git a/keyboards/planck/keymaps/dbroqua/readme.md b/keyboards/planck/keymaps/dbroqua/readme.md new file mode 100644 index 000000000..777c76abd --- /dev/null +++ b/keyboards/planck/keymaps/dbroqua/readme.md @@ -0,0 +1,14 @@ +# Dbroqua Layout + + + +* Online keyboard layout editor: http://www.keyboard-layout-editor.com/#/gists/e77306f9d14cc93fa26123b93b106474 +* Online keyboard layout editor (lower layer): http://www.keyboard-layout-editor.com/#/gists/786e03f6fbd274cb4f4e77a3d67f85fa +* Online keyboard layout editor (raise layer): http://www.keyboard-layout-editor.com/#/gists/2e22c71f6910103c20d595d1caa713d6 +* Online keyboard layout editor (multimedia layer): http://www.keyboard-layout-editor.com/#/gists/132ebf8053508a7a81dfa8e0756edb40 + +# Programming Instructions: +Enter into programming mode and run the following command. +``` +$ sudo KEYMAP=dbroqua make dfu +```
\ No newline at end of file diff --git a/keyboards/planck/keymaps/default/Makefile b/keyboards/planck/keymaps/default/Makefile index 38a504a27..0f4953888 100644 --- a/keyboards/planck/keymaps/default/Makefile +++ b/keyboards/planck/keymaps/default/Makefile @@ -11,7 +11,7 @@ CONSOLE_ENABLE = no # Console for debug(+400) COMMAND_ENABLE = yes # Commands for debug and configuration NKRO_ENABLE = yes # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work BACKLIGHT_ENABLE = yes # Enable keyboard backlight functionality -MIDI_ENABLE = yes # MIDI controls +MIDI_ENABLE = no # MIDI controls AUDIO_ENABLE = yes # Audio output on port C6 UNICODE_ENABLE = no # Unicode BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID @@ -22,4 +22,4 @@ SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend ifndef QUANTUM_DIR include ../../../../Makefile -endif
\ No newline at end of file +endif diff --git a/keyboards/planck/keymaps/experimental/Makefile b/keyboards/planck/keymaps/experimental/Makefile index 877c4aed0..3a8250a9b 100644 --- a/keyboards/planck/keymaps/experimental/Makefile +++ b/keyboards/planck/keymaps/experimental/Makefile @@ -16,6 +16,7 @@ AUDIO_ENABLE = no # Audio output on port C6 UNICODE_ENABLE = no # Unicode BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID RGBLIGHT_ENABLE = yes # Enable WS2812 RGB underlight. Do not enable this with audio at the same time. +ONEHAND_ENABLE = yes # Enable one-hand typing # Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend diff --git a/keyboards/planck/keymaps/experimental/keymap.c b/keyboards/planck/keymaps/experimental/keymap.c index d9303fcae..569dbcc8a 100644 --- a/keyboards/planck/keymaps/experimental/keymap.c +++ b/keyboards/planck/keymaps/experimental/keymap.c @@ -8,6 +8,7 @@ #endif #include "eeconfig.h" +#include "version.h" extern keymap_config_t keymap_config; @@ -69,7 +70,7 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { {KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_BSPC}, {KC_ESC, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT}, {KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, KC_ENT }, - {KC_LEAD, KC_LCTL, KC_LALT, KC_LGUI, LOWER, KC_SPC, KC_SPC, RAISE, KC_LEFT, KC_DOWN, KC_UP, KC_RGHT} + {KC_LEAD, KC_LCTL, KC_LALT, KC_LGUI, LOWER, KC_FN0, KC_FN0, RAISE, KC_LEFT, KC_DOWN, KC_UP, KC_RGHT} }, /* Colemak @@ -87,7 +88,7 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { {KC_TAB, KC_Q, KC_W, KC_F, KC_P, KC_G, KC_J, KC_L, KC_U, KC_Y, KC_SCLN, KC_BSPC}, {KC_ESC, KC_A, KC_R, KC_S, KC_T, KC_D, KC_H, KC_N, KC_E, KC_I, KC_O, KC_QUOT}, {KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_K, KC_M, KC_COMM, KC_DOT, KC_SLSH, KC_ENT }, - {KC_LEAD, KC_LCTL, KC_LALT, KC_LGUI, LOWER, KC_SPC, KC_SPC, RAISE, KC_LEFT, KC_DOWN, KC_UP, KC_RGHT} + {KC_LEAD, KC_LCTL, KC_LALT, KC_LGUI, LOWER, KC_FN0, KC_FN0, RAISE, KC_LEFT, KC_DOWN, KC_UP, KC_RGHT} }, /* Dvorak @@ -105,7 +106,7 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { {KC_TAB, KC_QUOT, KC_COMM, KC_DOT, KC_P, KC_Y, KC_F, KC_G, KC_C, KC_R, KC_L, KC_BSPC}, {KC_ESC, KC_A, KC_O, KC_E, KC_U, KC_I, KC_D, KC_H, KC_T, KC_N, KC_S, KC_SLSH}, {KC_LSFT, KC_SCLN, KC_Q, KC_J, KC_K, KC_X, KC_B, KC_M, KC_W, KC_V, KC_Z, KC_ENT }, - {KC_LEAD, KC_LCTL, KC_LALT, KC_LGUI, LOWER, KC_SPC, KC_SPC, RAISE, KC_LEFT, KC_DOWN, KC_UP, KC_RGHT} + {KC_LEAD, KC_LCTL, KC_LALT, KC_LGUI, LOWER, KC_FN0, KC_FN0, RAISE, KC_LEFT, KC_DOWN, KC_UP, KC_RGHT} }, /* Lower @@ -185,7 +186,7 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { }; const uint16_t PROGMEM fn_actions[] = { - + ACTION_SWAP_HANDS_TAP_KEY(KC_SPC), }; #ifdef AUDIO_ENABLE diff --git a/keyboards/planck/keymaps/jeebak/Makefile b/keyboards/planck/keymaps/jeebak/Makefile new file mode 100644 index 000000000..581e08cd0 --- /dev/null +++ b/keyboards/planck/keymaps/jeebak/Makefile @@ -0,0 +1,25 @@ + + +# Build Options +# change to "no" to disable the options, or define them in the Makefile in +# the appropriate keymap folder that will get included automatically +# +BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE = yes # Mouse keys(+4700) +EXTRAKEY_ENABLE = yes # Audio control and System control(+450) +CONSOLE_ENABLE = no # Console for debug(+400) +COMMAND_ENABLE = yes # Commands for debug and configuration +NKRO_ENABLE = yes # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +BACKLIGHT_ENABLE = yes # Enable keyboard backlight functionality +MIDI_ENABLE = no # MIDI controls +AUDIO_ENABLE = yes # Audio output on port C6 +UNICODE_ENABLE = no # Unicode +BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID +RGBLIGHT_ENABLE = no # Enable WS2812 RGB underlight. Do not enable this with audio at the same time. + +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend + +ifndef QUANTUM_DIR + include ../../../../Makefile +endif
\ No newline at end of file diff --git a/keyboards/planck/keymaps/jeebak/keymap.c b/keyboards/planck/keymaps/jeebak/keymap.c new file mode 100644 index 000000000..cb7ccb588 --- /dev/null +++ b/keyboards/planck/keymaps/jeebak/keymap.c @@ -0,0 +1,459 @@ +// This is the canonical layout file for the Quantum project. If you want to add another keyboard, +// this is the style you want to emulate. + +#include "planck.h" +#include "action_layer.h" +#ifdef AUDIO_ENABLE + #include "audio.h" +#endif +#include "eeconfig.h" + +extern keymap_config_t keymap_config; + +// Each layer gets a name for readability, which is then used in the keymap matrix below. +// The underscores don't mean anything - you can have a layer called STUFF or any other name. +// Layer names don't all need to be of the same length, obviously, and you can also skip them +// entirely and just use numbers. +#define _QWERTY 0 +#define _COLEMAK 1 +#define _DVORAK 2 +#define _LOWER 3 +#define _RAISE 4 +#define _PLOVER 5 +#define _TOUCHCURSOR 6 +#define _MOUSECURSOR 7 +#define _ADJUST 16 + +// Keycodes +enum planck_keycodes { + QWERTY = SAFE_RANGE, + COLEMAK, + DVORAK, + PLOVER, + LOWER, + RAISE, + BACKLIT, + EXT_PLV +}; + +enum macro_keycodes { + KC_ALT_TAB, + KC_CMD_TAB, + KC_CTL_TAB, + KC_CMD_SLSH, + KC_AG_FIND, + KC_AG_AGAIN, + KC_AG_UNDO, + KC_AG_CUT, + KC_AG_COPY, + KC_AG_PASTE, + KC_AG_DESK_L, + KC_AG_DESK_R, + KC_AG_TAB_C, + KC_AG_TAB_N, + KC_AG_TAB_R, +}; + +// Fillers to make layering more clear +#define _______ KC_TRNS +#define XXXXXXX KC_NO + +// Custom macros +#define CTL_ESC CTL_T(KC_ESC) // Tap for Esc, hold for Ctrl +#define SFT_ENT SFT_T(KC_ENT) // Tap for Enter, hold for Shift +#define HPR_TAB ALL_T(KC_TAB) // Tap for Tab, hold for Hyper +#define GUI_SEM GUI_T(KC_SCLN) // Tap for Semicolon, hold for GUI +#define ALT_QUO ALT_T(KC_QUOT) // Tap for Quote, hold for Alt +// Requires KC_TRNS/_______ for the trigger key in the destination layer +#define LT_TC LT(_TOUCHCURSOR, KC_SPC) // L-ayer T-ap T-ouch C-ursor +#define LT_MC(kc) LT(_MOUSECURSOR, kc) // L-ayer T-ap M-ouse C-ursor +#define ALT_TAB M(KC_ALT_TAB) // Macro for Alt-Tab +#define CMD_TAB M(KC_CMD_TAB) // Macro for Cmd-Tab +#define CTL_TAB M(KC_CTL_TAB) // Macro for Ctl-Tab +#define CMD_SLSH M(KC_CMD_SLSH) // Macro for Cmd-Slash (personal shortcut to toggle iTerm2 visibility) +#define AG_FIND M(KC_AG_FIND) // Macros for Cmd-[x] vs Ctrl-[x] based on current AG_NORM or AG_SWAP settings +#define AG_AGAIN M(KC_AG_AGAIN) +#define AG_UNDO M(KC_AG_UNDO) +#define AG_CUT M(KC_AG_CUT) +#define AG_COPY M(KC_AG_COPY) +#define AG_PASTE M(KC_AG_PASTE) +#define AG_D_L M(KC_AG_DESK_L) // For Virtual Desktop Switching: Left, and +#define AG_D_R M(KC_AG_DESK_R) // Right +#define AG_T_C M(KC_AG_TAB_C) // For Chrome, etc. Tab Close, +#define AG_T_N M(KC_AG_TAB_N) // Tab New, and +#define AG_T_R M(KC_AG_TAB_R) // Tab Reopen Closed + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { + +/* Qwerty + * ,-----------------------------------------------------------------------------------------. + * | Hyper/Tab| Q | W | E | R | T | Y | U | I | O | P | Bksp | + * |----------+------+------+------+------+-------------+------+------+------+------+--------| + * | Ctrl/Esc | A | S | MC/D | F | G | H | J | K | L |GUI/; | Alt/" | + * |----------+------+------+------+------+------|------+------+------+------+------+--------| + * | Shift | Z | X | C | V | B | N | M | , | . | / |Sft/Ent | + * |----------+------+------+------+------+------+------+------+------+------+------+--------| + * | PrntScrn | RGUI | Alt | GUI |Lower | TC/Space |Raise | Next | Vol- | Vol+ | Play | + * `-----------------------------------------------------------------------------------------' + */ +[_QWERTY] = { + {HPR_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_BSPC}, + {CTL_ESC, KC_A, KC_S, LT_MC(KC_D),KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, GUI_SEM, ALT_QUO}, + {KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, SFT_ENT}, + {KC_PSCR, KC_RGUI, KC_LALT, KC_LGUI, LOWER, LT_TC, LT_TC, RAISE, KC_MNXT, KC_VOLD, KC_VOLU, KC_MPLY} +}, + +/* Colemak + * ,-----------------------------------------------------------------------------------------. + * | Hyper/Tab| Q | W | F | P | G | J | L | U | Y | ; | Bksp | + * |----------+------+------+------+------+-------------+------+------+------+------+--------| + * | Ctrl/Esc | A | R | MC/S | T | D | H | N | E | I | O | " | + * |----------+------+------+------+------+------|------+------+------+------+------+--------| + * | Shift | Z | X | C | V | B | K | M | , | . | / |Sft/Ent | + * |----------+------+------+------+------+------+------+------+------+------+------+--------| + * | PrntScrn | RGUI | Alt | GUI |Lower | TC/Space |Raise | Next | Vol- | Vol+ | Play | + * `-----------------------------------------------------------------------------------------' + */ +[_COLEMAK] = { + {HPR_TAB, KC_Q, KC_W, KC_F, KC_P, KC_G, KC_J, KC_L, KC_U, KC_Y, KC_SCLN, KC_BSPC}, + {CTL_ESC, KC_A, KC_R, LT_MC(KC_S),KC_T, KC_D, KC_H, KC_N, KC_E, KC_I, KC_O, KC_QUOT}, + {KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_K, KC_M, KC_COMM, KC_DOT, KC_SLSH, SFT_ENT}, + {KC_PSCR, KC_RGUI, KC_LALT, KC_LGUI, LOWER, LT_TC, LT_TC, RAISE, KC_MNXT, KC_VOLD, KC_VOLU, KC_MPLY} +}, + +/* Dvorak + * ,-----------------------------------------------------------------------------------------. + * | Hyper/Tab| " | , | . | P | Y | F | G | C | R | L | Bksp | + * |----------+------+------+------+------+-------------+------+------+------+------+--------| + * | Ctrl/Esc | A | O | MC/E | U | I | D | H | T | N | S | / | + * |----------+------+------+------+------+------|------+------+------+------+------+--------| + * | Shift | ; | Q | J | K | X | B | M | W | V | Z |Sft/Ent | + * |----------+------+------+------+------+------+------+------+------+------+------+--------| + * | PrntScrn | RGUI | Alt | GUI |Lower | TC/Space |Raise | Next | Vol- | Vol+ | Play | + * `-----------------------------------------------------------------------------------------' + */ +[_DVORAK] = { + {HPR_TAB, KC_QUOT, KC_COMM, KC_DOT, KC_P, KC_Y, KC_F, KC_G, KC_C, KC_R, KC_L, KC_BSPC}, + {CTL_ESC, KC_A, KC_O, LT_MC(KC_E),KC_U, KC_I, KC_D, KC_H, KC_T, KC_N, KC_S, KC_SLSH}, + {KC_LSFT, KC_SCLN, KC_Q, KC_J, KC_K, KC_X, KC_B, KC_M, KC_W, KC_V, KC_Z, SFT_ENT}, + {KC_PSCR, KC_RGUI, KC_LALT, KC_LGUI, LOWER, LT_TC, LT_TC, RAISE, KC_MNXT, KC_VOLD, KC_VOLU, KC_MPLY} +}, + +/* Lower + * ,-----------------------------------------------------------------------------------. + * | ~ | ! | @ | # | $ | % | ^ | & | * | ( | ) | Bksp | + * |------+------+------+------+------+-------------+------+------+------+------+------| + * | [ | F1 | F2 | F3 | F4 | F5 | F6 | _ | + | { | } | | | + * |------+------+------+------+------+------|------+------+------+------+------+------| + * | ] | F7 | F8 | F9 | F10 | F11 | F12 | - | = | [ | ] | \ | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * |Brite | | | | | | | Prev | Stop | Slct | Mute | + * `-----------------------------------------------------------------------------------' + */ +[_LOWER] = { + {KC_TILD, KC_EXLM, KC_AT, KC_HASH, KC_DLR, KC_PERC, KC_CIRC, KC_AMPR, KC_ASTR, KC_LPRN, KC_RPRN, KC_BSPC}, + {KC_LBRC, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_UNDS, KC_PLUS, KC_LCBR, KC_RCBR, KC_PIPE}, + {KC_RBRC, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, KC_MINS, KC_EQL, KC_LBRC, KC_RBRC, KC_BSLS}, + {BACKLIT, _______, _______, _______, _______, _______, _______, _______, KC_MPRV, KC_MSTP, KC_MSEL, KC_MUTE} +}, + +/* Raise + * ,-----------------------------------------------------------------------------------. + * | 0 | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 0 | Bksp | + * |------+------+------+------+------+-------------+------+------+------+------+------| + * | $ | 4 | 5 | 6 | . | + | . | 4 | 5 | 6 | * | | | + * |------+------+------+------+------+------|------+------+------+------+------+------| + * | = | 7 | 8 | 9 | 0 | - | . | 1 | 2 | 3 | / | \ | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * |Brite | | | | | | | Prev | Stop | Slct | Mute | + * `-----------------------------------------------------------------------------------' + */ +[_RAISE] = { + {KC_0, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_BSPC}, + {KC_DLR, KC_4, KC_5, KC_6, KC_DOT, KC_PLUS, KC_DOT, KC_4, KC_5, KC_6, KC_ASTR, KC_PIPE}, + {KC_EQL, KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_DOT, KC_1, KC_2, KC_3, KC_SLSH, KC_BSLS}, + {BACKLIT, _______, _______, _______, _______, _______, _______, _______, KC_MPRV, KC_MSTP, KC_MSEL, KC_MUTE} +}, + +/* TouchCursor layer (http://martin-stone.github.io/touchcursor/) plus personal customizations + * ,-----------------------------------------------------------------------------------. + * |AltTab|CmdTab|CtlTab| GUI |Shift | ~ |Insert| Home | Up | End | Bksp | | + * |------+------+------+------+------+-------------+------+------+------+------+------| + * | | Alt |Space |Tab_C | Find |Again | PgUp | Left | Down |Right |Desk_L|Desk_R| + * |------+------+------+------+------+------|------+------+------+------+------+------| + * | | Undo | Cut | Copy |Paste | ` | PgDn | Del |Tab_N |Tab_R |iTerm2| | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | | | | | | | | | | | | + * `-----------------------------------------------------------------------------------' + * + * The KC_UNDO, KC_CUT, KC_COPY, KC_PASTE, KC_FIND, and KC_AGAIN keycodes don't + * seem to work on Mac. Presumably they'll work under Windows. + */ + +[_TOUCHCURSOR] = { + {ALT_TAB, CMD_TAB, CTL_TAB, KC_LGUI, KC_LSFT, KC_TILD, KC_INS, KC_HOME, KC_UP, KC_END, KC_BSPC, _______}, + {_______, KC_LALT, KC_SPC, AG_T_C, AG_FIND,AG_AGAIN, KC_PGUP, KC_LEFT, KC_DOWN, KC_RGHT, AG_D_L, AG_D_R }, + {_______, AG_UNDO, AG_CUT, AG_COPY, AG_PASTE,KC_GRV, KC_PGDN, KC_DEL, AG_T_N, AG_T_R, CMD_SLSH,_______}, + {_______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______} +}, + +/* Mouse Layer + * ,-----------------------------------------------------------------------------------. + * | | |ACCL0 | | | | |WHL_L | Up |WHL_R | BTN2 | | + * |------+------+------+------+------+-------------+------+------+------+------+------| + * | |ACCL2 | BTN2 | | BTN1 |ACCL1 |WHL_Up| Left | Down |Right | BTN4 | BTN5 | + * |------+------+------+------+------+------|------+------+------+------+------+------| + * | | | | | BTN3 | |WHL_Dn| BTN1 | | | BTN3 | | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | | | | | | | | | | | | + * `-----------------------------------------------------------------------------------' + */ + +[_MOUSECURSOR] = { + {_______, _______, KC_ACL0, _______, _______, _______, _______, KC_WH_L, KC_MS_U, KC_WH_R, KC_BTN2, _______}, + {_______, KC_ACL2, KC_BTN2, _______, KC_BTN1, KC_ACL1, KC_WH_U, KC_MS_L, KC_MS_D, KC_MS_R, KC_BTN4, KC_BTN5}, + {_______, _______, _______, _______, KC_BTN3, _______, KC_WH_D, KC_BTN1, _______, _______, KC_BTN3, _______}, + {_______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______} +}, + +/* Plover layer (http://opensteno.org) + * ,-----------------------------------------------------------------------------------. + * | # | # | # | # | # | # | # | # | # | # | # | # | + * |------+------+------+------+------+-------------+------+------+------+------+------| + * | | S | T | P | H | * | * | F | P | L | T | D | + * |------+------+------+------+------+------|------+------+------+------+------+------| + * |TogOut| S | K | W | R | * | * | R | B | G | S | Z | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | Exit | | | A | O | | E | U | | | | + * `-----------------------------------------------------------------------------------' + */ + +[_PLOVER] = { + {KC_1, KC_1, KC_1, KC_1, KC_1, KC_1, KC_1, KC_1, KC_1, KC_1, KC_1, KC_1 }, + {XXXXXXX, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_LBRC}, + {XXXXXXX, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT}, + {EXT_PLV, XXXXXXX, XXXXXXX, KC_C, KC_V, XXXXXXX, XXXXXXX, KC_N, KC_M, XXXXXXX, XXXXXXX, XXXXXXX} +}, + +/* Adjust (Lower + Raise) + * ,-----------------------------------------------------------------------------------. + * | | | | | | | | | | | | Del | + * |------+------+------+------+------+-------------+------+------+------+------+------| + * | | | |Aud on|Audoff|AGnorm|AGswap|Qwerty|Colemk|Dvorak|Plover| | + * |------+------+------+------+------+------|------+------+------+------+------+------| + * | |Voice-|Voice+|Mus on|Musoff|MIDIon|MIDIof| | | | | | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | | | | | | | | | | |Reset | + * `-----------------------------------------------------------------------------------' + */ +[_ADJUST] = { + {_______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, KC_DEL}, + {_______, _______, _______, AU_ON, AU_OFF, AG_NORM, AG_SWAP, QWERTY, COLEMAK, DVORAK, PLOVER, _______}, + {_______, MUV_DE, MUV_IN, MU_ON, MU_OFF, MI_ON, MI_OFF, _______, _______, _______, _______, _______}, + {_______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, RESET} +} + + +}; + +#ifdef AUDIO_ENABLE + +float tone_startup[][2] = SONG(STARTUP_SOUND); +float tone_qwerty[][2] = SONG(QWERTY_SOUND); +float tone_dvorak[][2] = SONG(DVORAK_SOUND); +float tone_colemak[][2] = SONG(COLEMAK_SOUND); +float tone_plover[][2] = SONG(PLOVER_SOUND); +float tone_plover_gb[][2] = SONG(PLOVER_GOODBYE_SOUND); +float music_scale[][2] = SONG(MUSIC_SCALE_SOUND); + +float tone_goodbye[][2] = SONG(GOODBYE_SOUND); +#endif + + +void persistant_default_layer_set(uint16_t default_layer) { + eeconfig_update_default_layer(default_layer); + default_layer_set(default_layer); +} + +bool process_record_user(uint16_t keycode, keyrecord_t *record) { + switch (keycode) { + case QWERTY: + if (record->event.pressed) { + #ifdef AUDIO_ENABLE + PLAY_NOTE_ARRAY(tone_qwerty, false, 0); + #endif + default_layer_set(1UL<<_QWERTY); + } + return false; + break; + case COLEMAK: + if (record->event.pressed) { + #ifdef AUDIO_ENABLE + PLAY_NOTE_ARRAY(tone_colemak, false, 0); + #endif + default_layer_set(1UL<<_COLEMAK); + } + return false; + break; + case DVORAK: + if (record->event.pressed) { + #ifdef AUDIO_ENABLE + PLAY_NOTE_ARRAY(tone_dvorak, false, 0); + #endif + default_layer_set(1UL<<_DVORAK); + } + return false; + break; + case LOWER: + if (record->event.pressed) { + layer_on(_LOWER); + update_tri_layer(_LOWER, _RAISE, _ADJUST); + } else { + layer_off(_LOWER); + update_tri_layer(_LOWER, _RAISE, _ADJUST); + } + return false; + break; + case RAISE: + if (record->event.pressed) { + layer_on(_RAISE); + update_tri_layer(_LOWER, _RAISE, _ADJUST); + } else { + layer_off(_RAISE); + update_tri_layer(_LOWER, _RAISE, _ADJUST); + } + return false; + break; + case BACKLIT: + if (record->event.pressed) { + register_code(KC_RSFT); + #ifdef BACKLIGHT_ENABLE + backlight_step(); + #endif + } else { + unregister_code(KC_RSFT); + } + return false; + break; + case PLOVER: + if (record->event.pressed) { + #ifdef AUDIO_ENABLE + stop_all_notes(); + PLAY_NOTE_ARRAY(tone_plover, false, 0); + #endif + layer_off(_RAISE); + layer_off(_LOWER); + layer_off(_ADJUST); + layer_on(_PLOVER); + if (!eeconfig_is_enabled()) { + eeconfig_init(); + } + keymap_config.raw = eeconfig_read_keymap(); + keymap_config.nkro = 1; + eeconfig_update_keymap(keymap_config.raw); + } + return false; + break; + case EXT_PLV: + if (record->event.pressed) { + #ifdef AUDIO_ENABLE + PLAY_NOTE_ARRAY(tone_plover_gb, false, 0); + #endif + layer_off(_PLOVER); + } + return false; + break; + } + return true; +} + +/* + * Macro definition + */ +const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt) +{ + if (!eeconfig_is_enabled()) { + eeconfig_init(); + } + + bool use_cmd = true; // Use, for example, Cmd-Tab, Cmd-C, Cmd-V, etc. + // Compare to MAGIC_SWAP_ALT_GUI and MAGIC_UNSWAP_ALT_GUI configs, set in: + // quantum/quantum.c + if(keymap_config.swap_lalt_lgui == 1 && keymap_config.swap_ralt_rgui == 1) { + use_cmd = false; // ... or, Alt-Tab, Ctrl-C, Ctrl-V, etc. + } + + switch (id) { + case KC_ALT_TAB: + if(use_cmd) { return (record->event.pressed ? MACRO( D(LALT), D(TAB), END ) : MACRO( U(TAB), END )); } + else { return (record->event.pressed ? MACRO( D(LGUI), D(TAB), END ) : MACRO( U(TAB), END )); } + case KC_CMD_TAB: + if(use_cmd) { return (record->event.pressed ? MACRO( D(LGUI), D(TAB), END ) : MACRO( U(TAB), END )); } + else { return (record->event.pressed ? MACRO( D(LALT), D(TAB), END ) : MACRO( U(TAB), END )); } + + case KC_CTL_TAB: + return (record->event.pressed ? MACRO( D(LCTRL), D(TAB), END ) : MACRO( U(TAB), END )); + case KC_CMD_SLSH: + return (record->event.pressed ? MACRO( D(LGUI), D(SLSH),END ) : MACRO( U(SLSH),END )); + + case KC_AG_FIND: + return use_cmd ? MACRODOWN( D(LGUI), T(F), END ) : MACRODOWN( D(LCTRL), T(F), END ); + case KC_AG_AGAIN: + return use_cmd ? MACRODOWN( D(LGUI), T(G), END ) : MACRODOWN( D(LCTRL), T(G), END ); + case KC_AG_UNDO: + return use_cmd ? MACRODOWN( D(LGUI), T(Z), END ) : MACRODOWN( D(LCTRL), T(Z), END ); + case KC_AG_CUT: + return use_cmd ? MACRODOWN( D(LGUI), T(X), END ) : MACRODOWN( D(LCTRL), T(X), END ); + case KC_AG_COPY: + return use_cmd ? MACRODOWN( D(LGUI), T(C), END ) : MACRODOWN( D(LCTRL), T(C), END ); + case KC_AG_PASTE: + return use_cmd ? MACRODOWN( D(LGUI), T(V), END ) : MACRODOWN( D(LCTRL), T(V), END ); + + case KC_AG_DESK_L: + return use_cmd ? MACRODOWN( D(LGUI), D(LCTRL), T(SCLN), END ) : MACRODOWN( D(LALT), D(LCTRL), T(SCLN), END ); + case KC_AG_DESK_R: + return use_cmd ? MACRODOWN( D(LGUI), D(LCTRL), T(QUOT), END ) : MACRODOWN( D(LALT), D(LCTRL), T(QUOT), END ); + + case KC_AG_TAB_C: + return use_cmd ? MACRODOWN( D(LGUI), T(W), END ) : MACRODOWN( D(LCTRL), T(W), END ); + case KC_AG_TAB_N: + return use_cmd ? MACRODOWN( D(LGUI), T(T), END ) : MACRODOWN( D(LCTRL), T(T), END ); + case KC_AG_TAB_R: + return use_cmd ? MACRODOWN( D(LGUI), D(LSHIFT), T(T), END ) : MACRODOWN( D(LCTRL), D(LSHIFT), T(T), END ); + } + + return MACRO_NONE; +} + +void matrix_init_user(void) { + #ifdef AUDIO_ENABLE + startup_user(); + #endif +} + +#ifdef AUDIO_ENABLE + +void startup_user() +{ + _delay_ms(20); // gets rid of tick + PLAY_NOTE_ARRAY(tone_startup, false, 0); +} + +void shutdown_user() +{ + PLAY_NOTE_ARRAY(tone_goodbye, false, 0); + _delay_ms(150); + stop_all_notes(); +} + +void music_on_user(void) +{ + music_scale_user(); +} + +void music_scale_user(void) +{ + PLAY_NOTE_ARRAY(music_scale, false, 0); +} + +#endif diff --git a/keyboards/planck/keymaps/jeebak/readme.md b/keyboards/planck/keymaps/jeebak/readme.md new file mode 100644 index 000000000..e1dd1dca5 --- /dev/null +++ b/keyboards/planck/keymaps/jeebak/readme.md @@ -0,0 +1,127 @@ +jeebak's layout +======================= +This WIP keymap attempts to minimize fingers straying away from the home row. +To aid in this endeavor, when additional modifyer keys to switch layers are +needed, they will be mapped to home row keys. The `keymap.c` file will contain +the exact changes. The diagrams in this README shows the highlights of the +changes from the default mappings. + +I also decided to change all calls to `persistant_default_layer_set()` to +`default_layer_set()` since this is my personal perference. + +## Macros +``` +#define ALT_TAB M(KC_ALT_TAB) +``` + +## Base Layers (Qwerty/Colemak/Dvorak) +These base layers are mostly the same as the default mappings. The interesting +changes are shown below. + +- The `Ctrl/Esc`, will emit an `Escape` when tapped, and act as a `Control` key when held, +- `GUI/;` as `;` and `GUI`, +- `Alt/"` as `"` and `Alt`, +- `Sft/Ent` as `Enter` and `Shift`, and +- `Hyper/Tab` as `Tab` and `Hyper` + +A `TODO` item is to see if it can also act as a `CapsLock` when double-tapped. +The arrow keys, which have been moved to the +[TouchCursor](http://martin-stone.github.io/touchcursor/) layer, have been +replaced with the Media keys as shown. The `MC/kc` key activates the +`MouseCursor` layer when held, and emits the corresponding `kc` for its layer, +when tapped. +``` + ,-----------------------------------------------------------------------------------------. + | Hyper/Tab| | | | | | | | | | | | + |----------+------+------+------+------+-------------+------+------+------+------+--------| + | Ctrl/Esc | | |MC/kc | | | | | | |GUI/; | Alt/" | + |----------+------+------+------+------+------|------+------+------+------+------+--------| + | | | | | | | | | | | |Sft/Ent | + |----------+------+------+------+------+------+------+------+------+------+------+--------| + | PrntScrn | RGUI | Alt | GUI |Lower | TC/Space |Raise | Next | Vol- | Vol+ | Play | + `-----------------------------------------------------------------------------------------' +``` + +## Lower Layer (Symbols and Function Keys) +The symbols and functions keys are essentially the same as the default mapping. +The most notable changes are that the symbol keys from the `RAISE` layer have +been moved here. The remaining Media keys replace those that are now on the +base layers. The `BACKLIT` key has also been moved here. +``` + ,-----------------------------------------------------------------------------------. + | ~ | ! | @ | # | $ | % | ^ | & | * | ( | ) | Bksp | + |------+------+------+------+------+-------------+------+------+------+------+------| + | [ | F1 | F2 | F3 | F4 | F5 | F6 | _ | + | { | } | | | + |------+------+------+------+------+------|------+------+------+------+------+------| + | ] | F7 | F8 | F9 | F10 | F11 | F12 | - | = | [ | ] | \ | + |------+------+------+------+------+------+------+------+------+------+------+------| + |Brite | | | | | | | Prev | Stop | Slct | Mute | + `-----------------------------------------------------------------------------------' +``` + +## Raise Layer (Numbers and Arithmetic Operators) +All of the numbers and arithmetic operators are available on this layer. Some +keys are duplicated for the convenience of their positions. The `0` and `$` +keys at the far left are for quick access to beginning and end of line in vim. +``` + ,-----------------------------------------------------------------------------------. + | 0 | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 0 | Bksp | + |------+------+------+------+------+-------------+------+------+------+------+------| + | $ | 4 | 5 | 6 | . | + | . | 4 | 5 | 6 | * | | | + |------+------+------+------+------+------|------+------+------+------+------+------| + | = | 7 | 8 | 9 | 0 | - | . | 1 | 2 | 3 | / | \ | + |------+------+------+------+------+------+------+------+------+------+------+------| + |Brite | | | | | | | Prev | Stop | Slct | Mute | + `-----------------------------------------------------------------------------------' +``` + +## TouchCursor layer plus personal customizations +[TouchCursor](http://martin-stone.github.io/touchcursor/) uses the `Space` key +as the modifier, with the `IJKL` home row keys representing the inverted-T of +the arrow keys. All of the default TouchCursor keymappings for the right hand +are represented below. My personalizations include all of the keys shown for +the left hand. Having the `Alt` and `Shift` keys (as well as the `Control` key +from the base layers) readily accessible from the home row allows quick word +jumps and highlighting when used in conjunction with the arrow keys. The +`Alt-Tab` macro is not only useful under Windows, but also under Mac when used +with alternative switchers like [HyperSwitch](https://bahoom.com/hyperswitch). +The `Cmd-Tab` and `Ctrl-Tab` sequences are duplicated for easy access while in +this layer. The `KC_UNDO, KC_CUT, KC_COPY, KC_PASTE, KC_FIND,` and `KC_AGAIN` +keycodes do not seem to work. There are macros in place that'll "automatically" +choose the correct version (`Cmd-Tab` vs. `Alt-Tab`, `Cmd-C` vs. `Ctrl-C`, +etc.) depending on which layout you've currently selected (`AG_NORM` or +`AG_SWAP`) in the `_ADJUST` layer. The `Desk_L` and `Desk_R` macros are what I +use to switch between Virtual Desktops Left/Right. The `Tab_C`, `Tab_N` and +`Tab_R` are for "Close Tab," "New Tab" and "Reopen Closed Tab" for apps such as +Google Chrome. +``` + ,-----------------------------------------------------------------------------------. + |AltTab|CmdTab|CtlTab| GUI |Shift | ~ |Insert| Home | Up | End | Bksp | | + |------+------+------+------+------+-------------+------+------+------+------+------| + | | Alt |Space |Tab_C | Find |Again | PgUp | Left | Down |Right |Desk_L|Desk_R| + |------+------+------+------+------+------|------+------+------+------+------+------| + | | Undo | Cut | Copy |Paste | ` | PgDn | Del |Tab_N |Tab_R |iTerm2| | + |------+------+------+------+------+------+------+------+------+------+------+------| + | | | | | | | | | | | | + `-----------------------------------------------------------------------------------' +``` + +## Mouse Layer +The Mouse layer, closely mimics the layout/behaviour of the TouchCursor layer. +The `D` key (on QWERTY) is used to activate this layer. All 16 keycodes for the +mouse from the `doc/keycode.txt` file are represented, and logically located, +IMHO. The left and right click buttons are duplicated; on the right hand side, +for a quick click here and there, and again on the left hand side for when the +buttons need to be held for dragging things or highlighting text, thus allowing +the right hand to be free to use the up/down/left/right actions. +``` + ,-----------------------------------------------------------------------------------. + | | |ACCL0 | | | | |WHL_L | Up |WHL_R | BTN2 | | + |------+------+------+------+------+-------------+------+------+------+------+------| + | |ACCL2 | BTN2 | | BTN1 |ACCL1 |WHL_Up| Left | Down |Right | BTN4 | BTN5 | + |------+------+------+------+------+------|------+------+------+------+------+------| + | | | | | BTN3 | |WHL_Dn| BTN1 | | | BTN3 | | + |------+------+------+------+------+------+------+------+------+------+------+------| + | | | | | | | | | | | | + `-----------------------------------------------------------------------------------' +``` diff --git a/keyboards/planck/keymaps/jhenahan/Makefile b/keyboards/planck/keymaps/jhenahan/Makefile new file mode 100644 index 000000000..de01ad240 --- /dev/null +++ b/keyboards/planck/keymaps/jhenahan/Makefile @@ -0,0 +1,25 @@ + + +# Build Options +# change to "no" to disable the options, or define them in the Makefile in +# the appropriate keymap folder that will get included automatically +# +BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE = yes # Mouse keys(+4700) +EXTRAKEY_ENABLE = yes # Audio control and System control(+450) +CONSOLE_ENABLE = no # Console for debug(+400) +COMMAND_ENABLE = yes # Commands for debug and configuration +NKRO_ENABLE = yes # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality +MIDI_ENABLE = no # MIDI controls +AUDIO_ENABLE = yes # Audio output on port C6 +UNICODE_ENABLE = no # Unicode +BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID +RGBLIGHT_ENABLE = no # Enable WS2812 RGB underlight. Do not enable this with audio at the same time. + +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend + +ifndef QUANTUM_DIR + include ../../../../Makefile +endif diff --git a/keyboards/planck/keymaps/jhenahan/config.h b/keyboards/planck/keymaps/jhenahan/config.h new file mode 100644 index 000000000..cd3adc41c --- /dev/null +++ b/keyboards/planck/keymaps/jhenahan/config.h @@ -0,0 +1,9 @@ +#ifndef CONFIG_USER_H +#define CONFIG_USER_H + +#include "../../config.h" + +#define FORCE_NKRO +#define WORKMAN_SOUND COLEMAK_SOUND + +#endif diff --git a/keyboards/planck/keymaps/jhenahan/keymap.c b/keyboards/planck/keymaps/jhenahan/keymap.c new file mode 100644 index 000000000..2bda4b695 --- /dev/null +++ b/keyboards/planck/keymaps/jhenahan/keymap.c @@ -0,0 +1,314 @@ +// This is the canonical layout file for the Quantum project. If you want to add another keyboard, +// this is the style you want to emulate. + +#include "planck.h" +#include "action_layer.h" +#ifdef AUDIO_ENABLE + #include "audio.h" +#endif +#include "eeconfig.h" + +extern keymap_config_t keymap_config; + +// Each layer gets a name for readability, which is then used in the keymap matrix below. +// The underscores don't mean anything - you can have a layer called STUFF or any other name. +// Layer names don't all need to be of the same length, obviously, and you can also skip them +// entirely and just use numbers. +#define _WORKMAN 0 +#define _DEAD 1 +#define _QWERTY 2 +#define _LOWER 3 +#define _RAISE 4 +#define _PLOVER 5 +#define _ADJUST 16 + +enum planck_keycodes { + WORKMAN = SAFE_RANGE, + DEAD, + QWERTY, + LOWER, + RAISE, + PLOVER, + EXT_PLV, + TOG_PLV +}; + +// Fillers to make layering more clear +#define _______ KC_TRNS +#define XXXXXXX KC_NO + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { + + +/* Workman + * ,-----------------------------------------------------------------------------------. + * | Tab | Q | D | R | W | B | J | F | U | P | ; | Bksp | + * |------+------+------+------+------+-------------+------+------+------+------+------| + * | Esc | A | S | H | T | G | Y | N | E | O | I | " | + * |------+------+------+------+------+------|------+------+------+------+------+------| + * | Shift| Z | X | M | C | V | K | L | Dead | . | / |Enter | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | Ctrl | RAlt | Alt | GUI |Lower | Space |Raise | Left | Down | Up |Right | + * `-----------------------------------------------------------------------------------' + */ +[_WORKMAN] = { + {KC_TAB, KC_Q, KC_D, KC_R, KC_W, KC_B, KC_J, KC_F, KC_U, KC_P, KC_SCLN, KC_BSPC}, + {MT(MOD_LCTL,KC_ESC), KC_A, KC_S, KC_H, KC_T, KC_G, KC_Y, KC_N, KC_E, KC_O, KC_I, KC_QUOT}, + {KC_LSFT, KC_Z, KC_X, KC_M, KC_C, KC_V, KC_K, KC_L, DEAD, KC_DOT, KC_SLSH, KC_ENT}, + {KC_LCTL, KC_RALT, KC_LALT, KC_LGUI, LOWER, KC_SPC, KC_SPC, RAISE, KC_LEFT, KC_DOWN, KC_UP, KC_RGHT} +}, + +/* Workman Dead Layer + * ,-----------------------------------------------------------------------------------. + * | | % | & | ? | + | @ | $ | _ | [ | ] | ! | | + * |------+------+------+------+------+-------------+------+------+------+------+------| + * | | / | ( | = | 0 | { | } | 1 | * | ) | - | " | + * |------+------+------+------+------+------|------+------+------+------+------+------| + * | | 6 | 7 | 8 | 9 | | | \ | 2 | 3 | 4 | 5 | | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | | | < | ~ | ` | , | # | ^ | > | | | + * `-----------------------------------------------------------------------------------' + */ +[_DEAD] = { + {XXXXXXX, KC_PERC, KC_AMPR, KC_QUES, KC_PLUS, KC_AT, KC_DLR, KC_UNDS, KC_LBRC, KC_RBRC, KC_EXLM, XXXXXXX}, + {XXXXXXX, KC_SLSH, KC_LPRN, KC_EQL, KC_0, KC_LCBR, KC_RCBR, KC_1, KC_ASTR, KC_RPRN, KC_MINS, XXXXXXX}, + {XXXXXXX, KC_6, KC_7, KC_8, KC_9, KC_PIPE, KC_BSLS, KC_2, KC_3, KC_4, KC_5, XXXXXXX}, + {XXXXXXX, XXXXXXX, KC_LT, KC_TILD, KC_GRV, KC_COMM, KC_COMM, KC_HASH, KC_CIRC, KC_GT, XXXXXXX, XXXXXXX} +}, + +/* Qwerty + * ,-----------------------------------------------------------------------------------. + * | Tab | Q | W | E | R | T | Y | U | I | O | P | Bksp | + * |------+------+------+------+------+-------------+------+------+------+------+------| + * | Esc | A | S | D | F | G | H | J | K | L | ; | " | + * |------+------+------+------+------+------|------+------+------+------+------+------| + * | Shift| Z | X | C | V | B | N | M | , | . | / |Enter | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | Ctrl | RAlt | Alt | GUI |Lower | Space |Raise | Left | Down | Up |Right | + * `-----------------------------------------------------------------------------------' + */ +[_QWERTY] = { + {KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_BSPC}, + {KC_ESC, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT}, + {KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, KC_ENT }, + {KC_LCTL, KC_RALT, KC_LALT, KC_LGUI, LOWER, KC_SPC, KC_SPC, RAISE, KC_LEFT, KC_DOWN, KC_UP, KC_RGHT} +}, + +/* Lower + * ,-----------------------------------------------------------------------------------. + * | ~ | ! | @ | # | $ | % | ^ | & | * | ( | ) | Bksp | + * |------+------+------+------+------+-------------+------+------+------+------+------| + * | Del | F1 | F2 | F3 | F4 | F5 | F6 | _ | + | { | } | | | + * |------+------+------+------+------+------|------+------+------+------+------+------| + * | | F7 | F8 | F9 | F10 | F11 | F12 |ISO ~ |ISO | | | Vol+ |Enter | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | | | | | | | | Prev | Next | Vol- | Play | + * `-----------------------------------------------------------------------------------' + */ +[_LOWER] = { + {KC_TILD, KC_EXLM, KC_AT, KC_HASH, KC_DLR, KC_PERC, KC_CIRC, KC_AMPR, KC_ASTR, KC_LPRN, KC_RPRN, KC_BSPC}, + {KC_DEL, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_UNDS, KC_PLUS, KC_LCBR, KC_RCBR, KC_PIPE}, + {_______, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12,S(KC_NUHS),S(KC_NUBS), _______, KC_VOLU, _______}, + {_______, _______, _______, _______, _______, _______, _______, _______, KC_MPRV, KC_MNXT, KC_VOLD, KC_MPLY} +}, + +/* Raise - KWM Interaction + * ,-----------------------------------------------------------------------------------. + * |Restrt| |TgSplt|Flotng|Parent|FlScrn|InsMrk| InsW | InsS | InsN | InsE | | + * |------+------+------+------+------+-------------+------+------+------+------+------| + * | | Mark |Rotate|Prefix| Term | BSP |SwpMrk|SwapW |SwapS |SwapN |SwapE | | + * |------+------+------+------+------+------|------+------+------+------+------+------| + * | |MarkW |MarkS |MarkN |MarkE |Monocl|Float |FocusW|FocusS|FocusN|FocusE| | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | | | | | | | | | | | | + * `-----------------------------------------------------------------------------------' + */ +[_RAISE] = { + {LCAG(KC_Q), XXXXXXX, LCAG(KC_S), LCAG(KC_W), LCAG(KC_D), LCAG(KC_F), LCTL(S(KC_X)), LCTL(S(KC_H)), LCTL(S(KC_J)), LCTL(S(KC_K)), LCTL(S(KC_L)), XXXXXXX}, + {XXXXXXX, LCAG(KC_M), LGUI(LCTL(KC_R)), LCAG(KC_DOT), LCAG(KC_T), LGUI(LCTL(KC_A)), LCTL(LALT(KC_M)), LCTL(LALT(KC_H)), LCTL(LALT(KC_J)), LCTL(LALT(KC_K)), LCTL(LALT(KC_L)), XXXXXXX}, + {_______, LCAG(KC_H), LCAG(KC_J), LCAG(KC_K), LCAG(KC_L), LGUI(LCTL(KC_S)), LGUI(LCTL(KC_D)), LGUI(LALT(KC_H)), LGUI(LALT(KC_J)), LGUI(LALT(KC_K)), LGUI(LALT(KC_L)), _______}, + {_______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______} +}, + +/* Plover layer (http://opensteno.org) + * ,-----------------------------------------------------------------------------------. + * | # | # | # | # | # | # | # | # | # | # | # | # | + * |------+------+------+------+------+-------------+------+------+------+------+------| + * | | S | T | P | H | * | * | F | P | L | T | D | + * |------+------+------+------+------+------|------+------+------+------+------+------| + * |TogOut| S | K | W | R | * | * | R | B | G | S | Z | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | Exit | | | A | O | | E | U | | | | + * `-----------------------------------------------------------------------------------' + */ + +[_PLOVER] = { + {KC_1, KC_1, KC_1, KC_1, KC_1, KC_1, KC_1, KC_1, KC_1, KC_1, KC_1, KC_1 }, + {XXXXXXX, KC_Q, KC_D, KC_R, KC_W, KC_B, KC_J, KC_F, KC_U, KC_P, KC_SCLN, KC_BSPC}, + {TOG_PLV, KC_A, KC_S, KC_H, KC_T, KC_G, KC_Y, KC_N, KC_E, KC_O, KC_I, KC_QUOT}, + {EXT_PLV, XXXXXXX, XXXXXXX, KC_M, KC_C, XXXXXXX, XXXXXXX, KC_L, KC_COMM, XXXXXXX, XXXXXXX, XXXXXXX} +}, + +/* Adjust (Lower + Raise) + * ,-----------------------------------------------------------------------------------. + * | | Reset| | | | | | | | | | Del | + * |------+------+------+------+------+-------------+------+------+------+------+------| + * | | | |Aud on|Audoff|AGnorm|AGswap|Qwerty|Workmn|Plover| | | + * |------+------+------+------+------+------|------+------+------+------+------+------| + * | |Voice-|Voice+|Mus on|Musoff|MIDIon|MIDIof| | | | | | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | | | | | | | | | | | | + * `-----------------------------------------------------------------------------------' + */ +[_ADJUST] = { + {_______, RESET, _______, _______, _______, _______, _______, _______, _______, _______, _______, KC_DEL}, + {_______, _______, _______, AU_ON, AU_OFF, AG_NORM, AG_SWAP, QWERTY, WORKMAN, PLOVER, _______, _______}, + {_______, MUV_DE, MUV_IN, MU_ON, MU_OFF, MI_ON, MI_OFF, _______, _______, _______, _______, _______}, + {_______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______} +} + + +}; + +#ifdef AUDIO_ENABLE + +float tone_startup[][2] = SONG(STARTUP_SOUND); +float tone_qwerty[][2] = SONG(QWERTY_SOUND); +float tone_workman[][2] = SONG(WORKMAN_SOUND); +float tone_plover[][2] = SONG(PLOVER_SOUND); +float tone_plover_gb[][2] = SONG(PLOVER_GOODBYE_SOUND); +float music_scale[][2] = SONG(MUSIC_SCALE_SOUND); + +float tone_goodbye[][2] = SONG(GOODBYE_SOUND); +#endif + + +void persistant_default_layer_set(uint16_t default_layer) { + eeconfig_update_default_layer(default_layer); + default_layer_set(default_layer); +} + +bool process_record_user(uint16_t keycode, keyrecord_t *record) { + switch (keycode) { + case WORKMAN: + if (record->event.pressed) { + #ifdef AUDIO_ENABLE + PLAY_NOTE_ARRAY(tone_workman, false, 0); + #endif + persistant_default_layer_set(1UL<<_WORKMAN); + } + return false; + break; + case DEAD: + if (record->event.pressed) { + layer_on(_DEAD); + set_oneshot_layer(_DEAD, ONESHOT_START); + clear_oneshot_layer_state(ONESHOT_PRESSED); + } + return false; + break; + case QWERTY: + if (record->event.pressed) { + #ifdef AUDIO_ENABLE + PLAY_NOTE_ARRAY(tone_qwerty, false, 0); + #endif + persistant_default_layer_set(1UL<<_QWERTY); + } + return false; + break; + case LOWER: + if (record->event.pressed) { + layer_on(_LOWER); + update_tri_layer(_LOWER, _RAISE, _ADJUST); + } else { + layer_off(_LOWER); + update_tri_layer(_LOWER, _RAISE, _ADJUST); + } + return false; + break; + case RAISE: + if (record->event.pressed) { + layer_on(_RAISE); + update_tri_layer(_LOWER, _RAISE, _ADJUST); + } else { + layer_off(_RAISE); + update_tri_layer(_LOWER, _RAISE, _ADJUST); + } + return false; + break; + case PLOVER: + if (record->event.pressed) { + #ifdef AUDIO_ENABLE + stop_all_notes(); + PLAY_NOTE_ARRAY(tone_plover, false, 0); + #endif + layer_off(_RAISE); + layer_off(_LOWER); + layer_off(_ADJUST); + layer_on(_PLOVER); + if (!eeconfig_is_enabled()) { + eeconfig_init(); + } + keymap_config.raw = eeconfig_read_keymap(); + keymap_config.nkro = 1; + eeconfig_update_keymap(keymap_config.raw); + } + return false; + break; + case EXT_PLV: + if (record->event.pressed) { + #ifdef AUDIO_ENABLE + PLAY_NOTE_ARRAY(tone_plover_gb, false, 0); + #endif + layer_off(_PLOVER); + } + return false; + break; + case TOG_PLV: + if (record->event.pressed) { + register_code(KC_R); + register_code(KC_W); + register_code(KC_T); + register_code(KC_C); + register_code(KC_P); + register_code(KC_O); + clear_keyboard(); + } + return false; + break; + } + return true; +} + +void matrix_init_user(void) { + #ifdef AUDIO_ENABLE + startup_user(); + #endif +} + +#ifdef AUDIO_ENABLE + +void startup_user() +{ + _delay_ms(20); // gets rid of tick + PLAY_NOTE_ARRAY(tone_startup, false, 0); +} + +void shutdown_user() +{ + PLAY_NOTE_ARRAY(tone_goodbye, false, 0); + _delay_ms(150); + stop_all_notes(); +} + +void music_on_user(void) +{ + music_scale_user(); +} + +void music_scale_user(void) +{ + PLAY_NOTE_ARRAY(music_scale, false, 0); +} + +#endif diff --git a/keyboards/planck/keymaps/jhenahan/readme.md b/keyboards/planck/keymaps/jhenahan/readme.md new file mode 100644 index 000000000..a80506fc9 --- /dev/null +++ b/keyboards/planck/keymaps/jhenahan/readme.md @@ -0,0 +1,41 @@ +# jhenahan's layout + +## Layout + +The base layer is based on the +[Workman Dead](https://github.com/ojbucao/Workman/tree/master/mac) layout. The +primary interaction layer is a slightly modified Workman layout with a 'dead' +key on the third row under the middle finger. The dead key activates a layer of +special characters. + +## [Layers](http://www.keyboard-layout-editor.com/#/gists/2b875f7d5d76fe4408c0a5b3bd76ddae) +### Function Layer + +This is very slightly modified from the default, mainly just to rearrange the media keys. + +### [KWM](https://github.com/koekeishiya/kwm) Interaction Layer + +`kwm` is a tiling window manager for OS X. The keys defined in my keymap +correspond to the settings I use in +[my `kwmrc` file](https://github.com/jhenahan/dotfiles/blob/master/kwm/kwmrc). + +### QWERTY + +Just in case. + +### [Plover](http://www.openstenoproject.org/plover/) + +This layout functions exactly as a Workman layout unless you're running the Plover +application. Includes a key for toggling Plover while it's running. + +Add this in the appropriate section of your `plover.cfg` to allow this altered layout: + +``` ini +[System: English Stenotype] +keymap[keyboard] = [["#", ["1", "2", "3", "4", "5", "6", "7", "8", "9", "0", "-", "="]], ["S-", ["q", "a"]], ["T-", ["d"]], ["K-", ["s"]], ["P-", ["r"]], ["W-", ["h"]], ["H-", ["w"]], ["R-", ["t"]], ["A-", ["m"]], ["O-", ["c"]], ["*", ["y", "g", "j", "b"]], ["-E", ["l"]], ["-U", [","]], ["-F", ["f"]], ["-R", ["n"]], ["-P", ["u"]], ["-B", ["e"]], ["-L", ["p"]], ["-G", ["o"]], ["-T", [";"]], ["-S", ["i"]], ["-D", ["BackSpace"]], ["-Z", ["'"]], ["no-op", ["\\", "]", "x", ".", "/"]], ["arpeggiate", ["space"]]] +``` + +### Adjust Layer + +This layer is only slightly modified from the default to remove Dvorak and +Colemak and replace them with Workman. diff --git a/keyboards/planck/keymaps/premek/Makefile b/keyboards/planck/keymaps/premek/Makefile new file mode 100644 index 000000000..0f4953888 --- /dev/null +++ b/keyboards/planck/keymaps/premek/Makefile @@ -0,0 +1,25 @@ + + +# Build Options +# change to "no" to disable the options, or define them in the Makefile in +# the appropriate keymap folder that will get included automatically +# +BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE = yes # Mouse keys(+4700) +EXTRAKEY_ENABLE = yes # Audio control and System control(+450) +CONSOLE_ENABLE = no # Console for debug(+400) +COMMAND_ENABLE = yes # Commands for debug and configuration +NKRO_ENABLE = yes # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +BACKLIGHT_ENABLE = yes # Enable keyboard backlight functionality +MIDI_ENABLE = no # MIDI controls +AUDIO_ENABLE = yes # Audio output on port C6 +UNICODE_ENABLE = no # Unicode +BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID +RGBLIGHT_ENABLE = no # Enable WS2812 RGB underlight. Do not enable this with audio at the same time. + +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend + +ifndef QUANTUM_DIR + include ../../../../Makefile +endif diff --git a/keyboards/planck/keymaps/premek/keymap.c b/keyboards/planck/keymaps/premek/keymap.c new file mode 100644 index 000000000..9b212ab25 --- /dev/null +++ b/keyboards/planck/keymaps/premek/keymap.c @@ -0,0 +1,231 @@ +// This is the canonical layout file for the Quantum project. If you want to add another keyboard, +// this is the style you want to emulate. + +#include "planck.h" +#include "action_layer.h" +#ifdef AUDIO_ENABLE + #include "audio.h" +#endif +#include "eeconfig.h" + +extern keymap_config_t keymap_config; + +// Each layer gets a name for readability, which is then used in the keymap matrix below. +// The underscores don't mean anything - you can have a layer called STUFF or any other name. +// Layer names don't all need to be of the same length, obviously, and you can also skip them +// entirely and just use numbers. +#define _QWERTY 0 +#define _COLEMAK 1 +#define _DVORAK 2 +#define _LOWER 3 +#define _RAISE 4 +#define _PLOVER 5 +#define _ADJUST 16 + +enum planck_keycodes { + QWERTY = SAFE_RANGE, + COLEMAK, + DVORAK, + PLOVER, + LOWER, + RAISE, + BACKLIT, + EXT_PLV +}; + +// Fillers to make layering more clear +#define _______ KC_TRNS +#define XXXXXXX KC_NO + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { + +[_QWERTY] = { + {KC_ESC, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_DEL, KC_Y, KC_U, KC_I, KC_O, KC_P }, + {KC_LSFT, KC_A, KC_S, KC_D, KC_F, KC_G, KC_TAB, KC_H, KC_J, KC_K, KC_L, KC_SCLN}, + {KC_LCTL, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_BSPC, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH}, + {KC_LGUI, _______, _______, KC_LALT, LOWER, KC_SPC, KC_ENT, KC_SPC, RAISE, KC_RALT, _______, KC_RGUI} +}, +[_COLEMAK] = { + {KC_TAB, KC_Q, KC_W, KC_F, KC_P, KC_G, KC_J, KC_L, KC_U, KC_Y, KC_SCLN, KC_BSPC}, + {KC_ESC, KC_A, KC_R, KC_S, KC_T, KC_D, KC_H, KC_N, KC_E, KC_I, KC_O, KC_QUOT}, + {KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_K, KC_M, KC_COMM, KC_DOT, KC_SLSH, KC_ENT }, + {BACKLIT, KC_LCTL, KC_LALT, KC_LGUI, LOWER, KC_SPC, KC_SPC, RAISE, KC_LEFT, KC_DOWN, KC_UP, KC_RGHT} +}, +[_DVORAK] = { + {KC_TAB, KC_QUOT, KC_COMM, KC_DOT, KC_P, KC_Y, KC_F, KC_G, KC_C, KC_R, KC_L, KC_BSPC}, + {KC_ESC, KC_A, KC_O, KC_E, KC_U, KC_I, KC_D, KC_H, KC_T, KC_N, KC_S, KC_SLSH}, + {KC_LSFT, KC_SCLN, KC_Q, KC_J, KC_K, KC_X, KC_B, KC_M, KC_W, KC_V, KC_Z, KC_ENT }, + {BACKLIT, KC_LCTL, KC_LALT, KC_LGUI, LOWER, KC_SPC, KC_SPC, RAISE, KC_LEFT, KC_DOWN, KC_UP, KC_RGHT} +}, +[_LOWER] = { + {KC_GRV, KC_1, KC_2, KC_3, KC_4, KC_5, _______, KC_6, KC_7, KC_8, KC_9, KC_0}, + {_______, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, _______, KC_F6, KC_HOME, KC_PGDN, KC_PGUP, KC_END }, + {_______, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, _______, KC_F12, KC_PLUS, KC_PIPE, KC_LCBR, KC_RCBR}, + {_______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______} +}, +[_RAISE] = { + {KC_TILD, KC_EXLM, KC_AT, KC_HASH, KC_DLR, KC_PERC, _______, KC_CIRC, KC_AMPR, KC_ASTR, KC_LPRN, KC_RPRN}, + {_______, _______, _______, KC_QUOT, KC_MINS, _______, _______, _______, KC_LEFT, KC_DOWN, KC_UP, KC_RGHT}, + {_______, KC_TILD, KC_GRV, KC_PLUS, KC_EQL, KC_PIPE, _______, KC_BSLS, KC_LBRC, KC_RBRC, KC_LCBR, KC_RCBR}, + {_______, _______, _______, _______, _______, _______, _______, _______, _______, KC_VOLD, KC_VOLU, KC_MPLY} +}, + +[_PLOVER] = { + {KC_1, KC_1, KC_1, KC_1, KC_1, KC_1, KC_1, KC_1, KC_1, KC_1, KC_1, KC_1 }, + {XXXXXXX, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_LBRC}, + {XXXXXXX, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT}, + {EXT_PLV, XXXXXXX, XXXXXXX, KC_C, KC_V, XXXXXXX, XXXXXXX, KC_N, KC_M, XXXXXXX, XXXXXXX, XXXXXXX} +}, +[_ADJUST] = { + {_______, RESET, _______, _______, _______, _______, _______, _______, _______, _______, _______, KC_DEL}, + {_______, _______, _______, AU_ON, AU_OFF, AG_NORM, AG_SWAP, QWERTY, COLEMAK, DVORAK, PLOVER, _______}, + {_______, MUV_DE, MUV_IN, MU_ON, MU_OFF, MI_ON, MI_OFF, _______, _______, _______, _______, _______}, + {_______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______} +} + + +}; + +#ifdef AUDIO_ENABLE + +float tone_startup[][2] = SONG(STARTUP_SOUND); +float tone_qwerty[][2] = SONG(QWERTY_SOUND); +float tone_dvorak[][2] = SONG(DVORAK_SOUND); +float tone_colemak[][2] = SONG(COLEMAK_SOUND); +float tone_plover[][2] = SONG(PLOVER_SOUND); +float tone_plover_gb[][2] = SONG(PLOVER_GOODBYE_SOUND); +float music_scale[][2] = SONG(MUSIC_SCALE_SOUND); + +float tone_goodbye[][2] = SONG(GOODBYE_SOUND); +#endif + + +void persistant_default_layer_set(uint16_t default_layer) { + eeconfig_update_default_layer(default_layer); + default_layer_set(default_layer); +} + +bool process_record_user(uint16_t keycode, keyrecord_t *record) { + switch (keycode) { + case QWERTY: + if (record->event.pressed) { + #ifdef AUDIO_ENABLE + PLAY_NOTE_ARRAY(tone_qwerty, false, 0); + #endif + persistant_default_layer_set(1UL<<_QWERTY); + } + return false; + break; + case COLEMAK: + if (record->event.pressed) { + #ifdef AUDIO_ENABLE + PLAY_NOTE_ARRAY(tone_colemak, false, 0); + #endif + persistant_default_layer_set(1UL<<_COLEMAK); + } + return false; + break; + case DVORAK: + if (record->event.pressed) { + #ifdef AUDIO_ENABLE + PLAY_NOTE_ARRAY(tone_dvorak, false, 0); + #endif + persistant_default_layer_set(1UL<<_DVORAK); + } + return false; + break; + case LOWER: + if (record->event.pressed) { + layer_on(_LOWER); + update_tri_layer(_LOWER, _RAISE, _ADJUST); + } else { + layer_off(_LOWER); + update_tri_layer(_LOWER, _RAISE, _ADJUST); + } + return false; + break; + case RAISE: + if (record->event.pressed) { + layer_on(_RAISE); + update_tri_layer(_LOWER, _RAISE, _ADJUST); + } else { + layer_off(_RAISE); + update_tri_layer(_LOWER, _RAISE, _ADJUST); + } + return false; + break; + case BACKLIT: + if (record->event.pressed) { + register_code(KC_RSFT); + #ifdef BACKLIGHT_ENABLE + backlight_step(); + #endif + } else { + unregister_code(KC_RSFT); + } + return false; + break; + case PLOVER: + if (record->event.pressed) { + #ifdef AUDIO_ENABLE + stop_all_notes(); + PLAY_NOTE_ARRAY(tone_plover, false, 0); + #endif + layer_off(_RAISE); + layer_off(_LOWER); + layer_off(_ADJUST); + layer_on(_PLOVER); + if (!eeconfig_is_enabled()) { + eeconfig_init(); + } + keymap_config.raw = eeconfig_read_keymap(); + keymap_config.nkro = 1; + eeconfig_update_keymap(keymap_config.raw); + } + return false; + break; + case EXT_PLV: + if (record->event.pressed) { + #ifdef AUDIO_ENABLE + PLAY_NOTE_ARRAY(tone_plover_gb, false, 0); + #endif + layer_off(_PLOVER); + } + return false; + break; + } + return true; +} + +void matrix_init_user(void) { + #ifdef AUDIO_ENABLE + startup_user(); + #endif +} + +#ifdef AUDIO_ENABLE + +void startup_user() +{ + _delay_ms(20); // gets rid of tick + PLAY_NOTE_ARRAY(tone_startup, false, 0); +} + +void shutdown_user() +{ + PLAY_NOTE_ARRAY(tone_goodbye, false, 0); + _delay_ms(150); + stop_all_notes(); +} + +void music_on_user(void) +{ + music_scale_user(); +} + +void music_scale_user(void) +{ + PLAY_NOTE_ARRAY(music_scale, false, 0); +} + +#endif diff --git a/keyboards/planck/keymaps/premek/readme.md b/keyboards/planck/keymaps/premek/readme.md new file mode 100644 index 000000000..16debdd63 --- /dev/null +++ b/keyboards/planck/keymaps/premek/readme.md @@ -0,0 +1,4 @@ +# Split Layout +Inspired by TECK + +[Layout](http://www.keyboard-layout-editor.com/##@_switchMount=cherry&switchBrand=gateron&switchType=KS-3-Tea&pcb:true%3B&@_c=%23e6e6e6&t=%23757575&a:7&fa@:5%3B%3B&=Esc&_a:4&fa@:5&:0&:0&:0&:0&:0&:0&:0&:0&:5%3B%3B&=%0A%0A!%0A1%0A%0A%0A%0A%0A%0AQ&=%0A%0A%2F@%0A2%0A%0A%0A%0A%0A%0AW&=%0A%0A%23%0A3%0A%0A%0A%0A%0A%0AE&=%0A%0A$%0A4%0A%0A%0A%0A%0A%0AR&=%0A%0A%25%0A5%0A%0A%0A%0A%0A%0AT&_c=%23e3b02d&a:7%3B&=Del&_c=%23e6e6e6&a:4%3B&=%0A%0A%5E%0A6%0A%0A%0A%0A%0A%0AY&=%0A%0A%2F&%0A7%0A%0A%0A%0A%0A%0AU&=%0A%0A*%0A8%0A%0A%0A%0A%0A%0AI&=%0A%0A(%0A9%0A%0A%0A%0A%0A%0AO&=%0A%0A)%0A0%0A%0A%0A%0A%0A%0AP%3B&@_a:7%3B&=Shift&_a:4%3B&=%0A%0A%0AF1%0A%0A%0A%0A%0A%0AA&=%0A%0A%0AF2%0A%0A%0A%0A%0A%0AS&=%0A%0A'%0AF3%0A%0A%0A%0A%0A%0AD&_c=%23e3b02d&n:true%3B&=%0A%0A-%0AF4%0A%0A%0A%0A%0A%0AF&_c=%23e6e6e6%3B&=%0A%0A%0AF5%0A%0A%0A%0A%0A%0AG&_c=%23e3b02d&a:7%3B&=Tab&_c=%23e6e6e6&a:4%3B&=%0A%0A%0AF6%0A%0A%0A%0A%0A%0AH&_c=%23e3b02d&n:true%3B&=%0A%0A%2F&larr%2F%3B%0AHom%0A%0A%0A%0A%0A%0AJ&_c=%23e6e6e6%3B&=%0A%0A%2F&darr%2F%3B%0APgD%0A%0A%0A%0A%0A%0AK&=%0A%0A%2F&uarr%2F%3B%0APgU%0A%0A%0A%0A%0A%0AL&=%0A%0A%2F&rarr%2F%3B%0AEnd%0A%0A%0A%0A%0A%0A%2F%3B%3B&@_a:7%3B&=Ctrl&_a:4%3B&=%0A%0A~%0AF7%0A%0A%0A%0A%0A%0AZ&=%0A%0A%60%0AF8%0A%0A%0A%0A%0A%0AX&=%0A%0A+%0AF9%0A%0A%0A%0A%0A%0AC&=%0A%0A%2F=%0AF10%0A%0A%0A%0A%0A%0AV&=%0A%0A%7C%0AF11%0A%0A%0A%0A%0A%0AB&_c=%23e3b02d&a:7%3B&=BSp&_c=%23e6e6e6&a:4%3B&=%0A%0A%5C%0AF12%0A%0A%0A%0A%0A%0AN&=%0A%0A%5B%0A%0A%0A%0A%0A%0A%0AM&=%0A%0A%5D%0A%0A%0A%0A%0A%0A%0A,&=%0A%0A%7B%0A%0A%0A%0A%0A%0A%0A.&=%0A%0A%7D%0A%0A%0A%0A%0A%0A%0A%2F%2F%3B&@_a:7%3B&=&=&=&=Alt&_c=%23e3b02d%3B&=%2F&dArr%2F%3B&_c=%23e6e6e6%3B&=spc&_c=%23e3b02d%3B&=%2F&crarr%2F%3B&_c=%23e6e6e6%3B&=spc&_c=%23e3b02d%3B&=%2F&uArr%2F%3B&_c=%23e6e6e6%3B&=Alt&=&=) diff --git a/keyboards/planck/keymaps/pvc/keymap.c b/keyboards/planck/keymaps/pvc/keymap.c index 2fc5f0da1..0bb7f0def 100644 --- a/keyboards/planck/keymaps/pvc/keymap.c +++ b/keyboards/planck/keymaps/pvc/keymap.c @@ -166,9 +166,9 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { * .-----------------------------------------------------------------------------------------------------------. * | | $ | { | [ | ( | % | # | ) | ] | } | @ | PG UP | * |--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------| - * | | ^ | * | + | - | ; | : | _ | ' | " | ` | PG DN | + * | | ^ | * | + | - | / | \ | _ | ' | " | ` | PG DN | * |--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------| - * | | | | & | ! | ~ | / | \ | = | < | > | ? | HOME | + * | | | | & | ! | ~ | ; | : | = | < | > | ? | HOME | * |--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+-----------------| * | | | | | | | | | | | | END | * '-----------------------------------------------------------------------------------------------------------' @@ -176,27 +176,27 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { [LAYER_LOWER] = { // LOWER { _______, KC_DLR, KC_LCBR, KC_LBRC, KC_LPRN, KC_PERC, KC_HASH, KC_RPRN, KC_RBRC, KC_RCBR, KC_AT, KC_PGUP }, - { _______, KC_CIRC, KC_ASTR, KC_PPLS, KC_PMNS, KC_SCLN, KC_COLN, KC_UNDS, KC_QUOT, KC_DQT, KC_GRV, KC_PGDN }, - { _______, KC_PIPE, KC_AMPR, KC_EXLM, KC_TILD, KC_SLSH, KC_BSLS, KC_EQL, KC_LT, KC_GT, KC_QUES, KC_HOME }, + { _______, KC_CIRC, KC_ASTR, KC_PPLS, KC_PMNS, KC_SLSH, KC_BSLS, KC_UNDS, KC_QUOT, KC_DQT, KC_GRV, KC_PGDN }, + { _______, KC_PIPE, KC_AMPR, KC_EXLM, KC_TILD, KC_SCLN, KC_COLN, KC_EQL, KC_LT, KC_GT, KC_QUES, KC_HOME }, { _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, KC_END }, }, /* FUNCTION * .-----------------------------------------------------------------------------------------------------------. - * | NUM LK | F1 | F2 | F3 | F4 | F5 | F6 | F7 | F8 | F9 | F10 | PAUSE | + * | NUM LK | F13 | F14 | F15 | F16 | XXXXXX | XXXXXX | XXXXXX | XXXXXX | XXXXXX | XXXXXX | PAUSE | * |--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------| - * | CAP LK | F11 | F12 | F13 | F14 | F15 | F16 | F17 | F18 | F19 | F20 | PRINT | + * | CAP LK | F17 | F18 | F19 | F20 | XXXXXX | XXXXXX | XXXXXX | XXXXXX | XXXXXX | XXXXXX | PRINT | * |--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------| - * | SCR LK | XXXXXX | XXXXXX | XXXXXX | XXXXXX | XXXXXX | XXXXXX | XXXXXX | XXXXXX | XXXXXX | XXXXXX | MUTE | + * | SCR LK | F21 | F22 | F23 | F24 | XXXXXX | XXXXXX | XXXXXX | XXXXXX | XXXXXX | XXXXXX | MUTE | * |--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------| * | LCTRL | LWIN | FN | LALT | UPPER | PLAY | PLAY | LOWER | VOL UP | VOL DN | NEXT | PREV | * '-----------------------------------------------------------------------------------------------------------' */ [LAYER_FUNCTION] = { // FUNCTION - { KC_NLCK, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_PAUS }, - { KC_CAPS, KC_F11, KC_F12, KC_F13, KC_F14, KC_F15, KC_F16, KC_F17, KC_F18, KC_F19, KC_F20, KC_PSCR }, - { KC_SLCK, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, KC_MUTE }, + { KC_NLCK, KC_F13, KC_F14, KC_F15, KC_F16, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, KC_PAUS }, + { KC_CAPS, KC_F17, KC_F18, KC_F19, KC_F20, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, KC_PSCR }, + { KC_SLCK, KC_F21, KC_F22, KC_F23, KC_F24, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, KC_MUTE }, { _______, _______, _______, _______, _______, KC_MPLY, KC_MPLY, _______, KC_VOLU, KC_VOLD, KC_MPRV, KC_MNXT }, }, diff --git a/keyboards/planck/keymaps/xyverz/keymap.c b/keyboards/planck/keymaps/xyverz/keymap.c new file mode 100644 index 000000000..192933b18 --- /dev/null +++ b/keyboards/planck/keymaps/xyverz/keymap.c @@ -0,0 +1,262 @@ +// This is the canonical layout file for the Quantum project. If you want to add another keyboard, +// this is the style you want to emulate. + +#include "planck.h" +#include "action_layer.h" +#ifdef AUDIO_ENABLE + #include "audio.h" +#endif +#include "eeconfig.h" + +extern keymap_config_t keymap_config; + +// Each layer gets a name for readability, which is then used in the keymap matrix below. +// The underscores don't mean anything - you can have a layer called STUFF or any other name. +// Layer names don't all need to be of the same length, obviously, and you can also skip them +// entirely and just use numbers. +#define _QWERTY 0 +#define _COLEMAK 1 +#define _DVORAK 2 +#define _LOWER 3 +#define _RAISE 4 +#define _ADJUST 16 + +enum planck_keycodes { + QWERTY = SAFE_RANGE, + COLEMAK, + DVORAK, + LOWER, + RAISE, + BACKLIT +}; + +// Fillers to make layering more clear +#define _______ KC_TRNS +#define XXXXXXX KC_NO + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { + +/* Qwerty + * ,-----------------------------------------------------------------------------------. + * | Tab | Q | W | E | R | T | Y | U | I | O | P | Bksp | + * |------+------+------+------+------+-------------+------+------+------+------+------| + * | Esc | A | S | D | F | G | H | J | K | L | ; | " | + * |------+------+------+------+------+------|------+------+------+------+------+------| + * | Shift| Z | X | C | V | B | N | M | , | . | / |Enter | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | Brite| Ctrl | Alt | GUI |Lower | Space |Raise | Left | Down | Up |Right | + * `-----------------------------------------------------------------------------------' + */ +[_QWERTY] = { + {KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_BSPC}, + {KC_ESC, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT}, + {KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, KC_ENT }, + {BACKLIT, KC_LCTL, KC_LALT, KC_LGUI, LOWER, KC_SPC, KC_SPC, RAISE, KC_LEFT, KC_DOWN, KC_UP, KC_RGHT} +}, + +/* Colemak + * ,-----------------------------------------------------------------------------------. + * | Tab | Q | W | F | P | G | J | L | U | Y | ; | Bksp | + * |------+------+------+------+------+-------------+------+------+------+------+------| + * | Esc | A | R | S | T | D | H | N | E | I | O | " | + * |------+------+------+------+------+------|------+------+------+------+------+------| + * | Shift| Z | X | C | V | B | K | M | , | . | / |Enter | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | Brite| Ctrl | Alt | GUI |Lower | Space |Raise | Left | Down | Up |Right | + * `-----------------------------------------------------------------------------------' + */ +[_COLEMAK] = { + {KC_TAB, KC_Q, KC_W, KC_F, KC_P, KC_G, KC_J, KC_L, KC_U, KC_Y, KC_SCLN, KC_BSPC}, + {KC_ESC, KC_A, KC_R, KC_S, KC_T, KC_D, KC_H, KC_N, KC_E, KC_I, KC_O, KC_QUOT}, + {KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_K, KC_M, KC_COMM, KC_DOT, KC_SLSH, KC_ENT }, + {BACKLIT, KC_LCTL, KC_LALT, KC_LGUI, LOWER, KC_SPC, KC_SPC, RAISE, KC_LEFT, KC_DOWN, KC_UP, KC_RGHT} +}, + +/* Dvorak + * ,-----------------------------------------------------------------------------------. + * | Tab | " | , | . | P | Y | F | G | C | R | L | / | + * |------+------+------+------+------+-------------+------+------+------+------+------| + * | Esc | A | O | E | U | I | D | H | T | N | S | - | + * |------+------+------+------+------+------|------+------+------+------+------+------| + * | Shift| ; | Q | J | K | X | B | M | W | V | Z | Shift| + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | Ctrl | Alt | Left |Right |Lower | Bksp |Space |Raise | Up | Down | GUI |Enter | + * `-----------------------------------------------------------------------------------' + */ +[_DVORAK] = { + {KC_TAB, KC_QUOT, KC_COMM, KC_DOT, KC_P, KC_Y, KC_F, KC_G, KC_C, KC_R, KC_L, KC_SLSH}, + {KC_ESC, KC_A, KC_O, KC_E, KC_U, KC_I, KC_D, KC_H, KC_T, KC_N, KC_S, KC_MINS}, + {KC_LSFT, KC_SCLN, KC_Q, KC_J, KC_K, KC_X, KC_B, KC_M, KC_W, KC_V, KC_Z, SFT_T(KC_ENT)}, + {KC_LCTL, KC_LALT, KC_LEFT, KC_RGHT, LOWER, KC_BSPC, KC_SPC, RAISE, KC_UP, KC_DOWN, KC_RGUI, KC_ENT } +}, + +/* Lower + * ,-----------------------------------------------------------------------------------. + * | ~ | ! | @ | # | $ | % | ^ | & | * | ( | ) | | + * |------+------+------+------+------+-------------+------+------+------+------+------| + * | Caps | F1 | F2 | F3 | F4 | F5 | F6 | _ | + | { | } | | | + * |------+------+------+------+------+------|------+------+------+------+------+------| + * | | F7 | F8 | F9 | F10 | F11 | F12 | | Mute | Vol- | Vol+ | | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | Brite| | Home | End | | Del | Ins | | PgUp | PgDN | |Enter | + * `-----------------------------------------------------------------------------------' + */ +[_LOWER] = { + {KC_TILD, KC_EXLM, KC_AT, KC_HASH, KC_DLR, KC_PERC, KC_CIRC, KC_AMPR, KC_ASTR, KC_LPRN, KC_RPRN, _______}, + {KC_CAPS, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_UNDS, KC_PLUS, KC_LCBR, KC_RCBR, KC_PIPE}, + {_______, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, KC_MUTE, KC_VOLD, KC_VOLU, _______, _______}, + {BACKLIT, _______, KC_HOME, KC_END, _______, KC_DEL, KC_INS, _______, KC_PGUP, KC_PGDN, _______, _______} +}, + +/* Raise + * ,-----------------------------------------------------------------------------------. + * | ` | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 0 | | + * |------+------+------+------+------+-------------+------+------+------+------+------| + * | Caps | F1 | F2 | F3 | F4 | F5 | F6 | - | = | [ | ] | \ | + * |------+------+------+------+------+------|------+------+------+------+------+------| + * | | F7 | F8 | F9 | F10 | F11 | F12 | | Prev | Play | Next | | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | Brite| | Home | End | | Del | Ins | | PgUp | PgDN | |Enter | + * `-----------------------------------------------------------------------------------' + */ +[_RAISE] = { + {KC_GRV, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, _______}, + {KC_CAPS, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_MINS, KC_EQL, KC_LBRC, KC_RBRC, KC_BSLS}, + {_______, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, KC_MPRV, KC_MPLY, KC_MNXT, _______, _______}, + {BACKLIT, _______, KC_HOME, KC_END, _______, KC_DEL, KC_INS, _______, KC_PGUP, KC_PGDN, _______, _______} +}, + +/* Adjust (Lower + Raise) + * ,-----------------------------------------------------------------------------------. + * | | Reset| | | | | | | | | | Del | + * |------+------+------+------+------+-------------+------+------+------+------+------| + * | | | |Aud on|Audoff|AGnorm|AGswap|Qwerty|Colemk|Dvorak| | | + * |------+------+------+------+------+------|------+------+------+------+------+------| + * | |Voice-|Voice+|Mus on|Musoff|MIDIon|MIDIof| | | | | | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | | | | | | | | | | | | + * `-----------------------------------------------------------------------------------' + */ +[_ADJUST] = { + {_______, RESET, _______, _______, _______, _______, _______, _______, _______, _______, _______, KC_DEL}, + {_______, _______, _______, AU_ON, AU_OFF, AG_NORM, AG_SWAP, QWERTY, COLEMAK, DVORAK, _______, _______}, + {_______, MUV_DE, MUV_IN, MU_ON, MU_OFF, MI_ON, MI_OFF, _______, _______, _______, _______, _______}, + {_______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______} +} + + +}; + +#ifdef AUDIO_ENABLE + +float tone_startup[][2] = SONG(STARTUP_SOUND); +float tone_qwerty[][2] = SONG(QWERTY_SOUND); +float tone_dvorak[][2] = SONG(DVORAK_SOUND); +float tone_colemak[][2] = SONG(COLEMAK_SOUND); +float music_scale[][2] = SONG(MUSIC_SCALE_SOUND); + +float tone_goodbye[][2] = SONG(GOODBYE_SOUND); +#endif + + +void persistant_default_layer_set(uint16_t default_layer) { + eeconfig_update_default_layer(default_layer); + default_layer_set(default_layer); +} + +bool process_record_user(uint16_t keycode, keyrecord_t *record) { + switch (keycode) { + case QWERTY: + if (record->event.pressed) { + #ifdef AUDIO_ENABLE + PLAY_NOTE_ARRAY(tone_qwerty, false, 0); + #endif + persistant_default_layer_set(1UL<<_QWERTY); + } + return false; + break; + case COLEMAK: + if (record->event.pressed) { + #ifdef AUDIO_ENABLE + PLAY_NOTE_ARRAY(tone_colemak, false, 0); + #endif + persistant_default_layer_set(1UL<<_COLEMAK); + } + return false; + break; + case DVORAK: + if (record->event.pressed) { + #ifdef AUDIO_ENABLE + PLAY_NOTE_ARRAY(tone_dvorak, false, 0); + #endif + persistant_default_layer_set(1UL<<_DVORAK); + } + return false; + break; + case LOWER: + if (record->event.pressed) { + layer_on(_LOWER); + update_tri_layer(_LOWER, _RAISE, _ADJUST); + } else { + layer_off(_LOWER); + update_tri_layer(_LOWER, _RAISE, _ADJUST); + } + return false; + break; + case RAISE: + if (record->event.pressed) { + layer_on(_RAISE); + update_tri_layer(_LOWER, _RAISE, _ADJUST); + } else { + layer_off(_RAISE); + update_tri_layer(_LOWER, _RAISE, _ADJUST); + } + return false; + break; + case BACKLIT: + if (record->event.pressed) { + register_code(KC_RSFT); + #ifdef BACKLIGHT_ENABLE + backlight_step(); + #endif + } else { + unregister_code(KC_RSFT); + } + return false; + break; + } + return true; +} + +void matrix_init_user(void) { + #ifdef AUDIO_ENABLE + startup_user(); + #endif +} + +#ifdef AUDIO_ENABLE + +void startup_user() +{ + _delay_ms(20); // gets rid of tick + PLAY_NOTE_ARRAY(tone_startup, false, 0); +} + +void shutdown_user() +{ + PLAY_NOTE_ARRAY(tone_goodbye, false, 0); + _delay_ms(150); + stop_all_notes(); +} + +void music_on_user(void) +{ + music_scale_user(); +} + +void music_scale_user(void) +{ + PLAY_NOTE_ARRAY(music_scale, false, 0); +} + +#endif diff --git a/keyboards/planck/keymaps/xyverz/makefile.mk b/keyboards/planck/keymaps/xyverz/makefile.mk new file mode 100644 index 000000000..93a89bb4a --- /dev/null +++ b/keyboards/planck/keymaps/xyverz/makefile.mk @@ -0,0 +1,25 @@ + + +# Build Options +# change to "no" to disable the options, or define them in the Makefile in +# the appropriate keymap folder that will get included automatically +# +BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE = yes # Mouse keys(+4700) +EXTRAKEY_ENABLE = yes # Audio control and System control(+450) +CONSOLE_ENABLE = no # Console for debug(+400) +COMMAND_ENABLE = yes # Commands for debug and configuration +NKRO_ENABLE = yes # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +BACKLIGHT_ENABLE = yes # Enable keyboard backlight functionality +MIDI_ENABLE = no # MIDI controls +AUDIO_ENABLE = yes # Audio output on port C6 +UNICODE_ENABLE = no # Unicode +BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID +RGBLIGHT_ENABLE = no # Enable WS2812 RGB underlight. Do not enable this with audio at the same time. + +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend + +ifndef QUANTUM_DIR + include ../../../../Makefile +endif diff --git a/keyboards/planck/planck.c b/keyboards/planck/planck.c index 8d70bb4e5..645b450d1 100644 --- a/keyboards/planck/planck.c +++ b/keyboards/planck/planck.c @@ -1,5 +1,15 @@ #include "planck.h" +#ifdef ONEHAND_ENABLE +__attribute__ ((weak)) +const keypos_t hand_swap_config[MATRIX_ROWS][MATRIX_COLS] = { + {{11, 0}, {10, 0}, {9, 0}, {8, 0}, {7, 0}, {6, 0}, {5, 0}, {4, 0}, {3, 0}, {2, 0}, {1, 0}, {0, 0}}, + {{11, 1}, {10, 1}, {9, 1}, {8, 1}, {7, 1}, {6, 1}, {5, 1}, {4, 1}, {3, 1}, {2, 1}, {1, 1}, {0, 1}}, + {{11, 2}, {10, 2}, {9, 2}, {8, 2}, {7, 2}, {6, 2}, {5, 2}, {4, 2}, {3, 2}, {2, 2}, {1, 2}, {0, 2}}, + {{11, 3}, {10, 3}, {9, 3}, {8, 3}, {7, 3}, {6, 3}, {5, 3}, {4, 3}, {3, 3}, {2, 3}, {1, 3}, {0, 3}}, +}; +#endif + void matrix_init_kb(void) { // Turn status LED on DDRE |= (1<<6); diff --git a/keyboards/planck/readme.md b/keyboards/planck/readme.md index f89fdeb93..4b24a690e 100644 --- a/keyboards/planck/readme.md +++ b/keyboards/planck/readme.md @@ -13,15 +13,17 @@ Download or clone the whole firmware and navigate to the keyboards/planck folder Depending on which keymap you would like to use, you will have to compile slightly differently. ### Default -To build with the default keymap, simply run `make`. +To build with the default keymap, simply run `make default`. ### Other Keymaps Several version of keymap are available in advance but you are recommended to define your favorite layout yourself. To define your own keymap create file named `<name>.c` in the keymaps folder, and see keymap document (you can find in top readme.md) and existent keymap files. -To build the firmware binary hex file with a keymap just do `make` with `KEYMAP` option like: +To build the firmware binary hex file with a keymap just do `make` with a keymap like this: + ``` -$ make KEYMAP=[default|jack|<name>] +$ make [default|jack|<name>] ``` + Keymaps follow the format **__\<name\>.c__** and are stored in the `keymaps` folder. ### Notable forks (which some of the keymap files are from) diff --git a/keyboards/planck/rev3/Makefile b/keyboards/planck/rev3/Makefile index 3ed1445e4..191c6bb66 100644 --- a/keyboards/planck/rev3/Makefile +++ b/keyboards/planck/rev3/Makefile @@ -1,5 +1,3 @@ -AUDIO_ENABLE ?= no # Audio output on port C6 - -ifndef QUANTUM_DIR +ifndef MAKEFILE_INCLUDED include ../../../Makefile endif
\ No newline at end of file diff --git a/keyboards/planck/rev3/rules.mk b/keyboards/planck/rev3/rules.mk new file mode 100644 index 000000000..3ed1445e4 --- /dev/null +++ b/keyboards/planck/rev3/rules.mk @@ -0,0 +1,5 @@ +AUDIO_ENABLE ?= no # Audio output on port C6 + +ifndef QUANTUM_DIR + include ../../../Makefile +endif
\ No newline at end of file diff --git a/keyboards/planck/rev4/Makefile b/keyboards/planck/rev4/Makefile index ed09f85a4..191c6bb66 100644 --- a/keyboards/planck/rev4/Makefile +++ b/keyboards/planck/rev4/Makefile @@ -1,5 +1,3 @@ -AUDIO_ENABLE ?= yes # Audio output on port C6 - -ifndef QUANTUM_DIR +ifndef MAKEFILE_INCLUDED include ../../../Makefile endif
\ No newline at end of file diff --git a/keyboards/planck/rev4/rules.mk b/keyboards/planck/rev4/rules.mk new file mode 100644 index 000000000..ed09f85a4 --- /dev/null +++ b/keyboards/planck/rev4/rules.mk @@ -0,0 +1,5 @@ +AUDIO_ENABLE ?= yes # Audio output on port C6 + +ifndef QUANTUM_DIR + include ../../../Makefile +endif
\ No newline at end of file diff --git a/keyboards/planck/rules.mk b/keyboards/planck/rules.mk new file mode 100644 index 000000000..25db53a31 --- /dev/null +++ b/keyboards/planck/rules.mk @@ -0,0 +1,67 @@ +# MCU name +#MCU = at90usb1287 +MCU = atmega32u4 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + +# Boot Section Size in *bytes* +# Teensy halfKay 512 +# Teensy++ halfKay 1024 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +# USBaspLoader 2048 +OPT_DEFS += -DBOOTLOADER_SIZE=4096 + +# Build Options +# change to "no" to disable the options, or define them in the Makefile in +# the appropriate keymap folder that will get included automatically +# +BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) +EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) +CONSOLE_ENABLE ?= no # Console for debug(+400) +COMMAND_ENABLE ?= yes # Commands for debug and configuration +NKRO_ENABLE ?= no # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality +MIDI_ENABLE ?= no # MIDI controls +AUDIO_ENABLE ?= no # Audio output on port C6 +UNICODE_ENABLE ?= no # Unicode +BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID +RGBLIGHT_ENABLE ?= no # Enable WS2812 RGB underlight. Do not enable this with audio at the same time. + +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend
\ No newline at end of file |
