diff options
Diffstat (limited to 'lib/lufa/Demos/Device/ClassDriver/MassStorage/MassStorage.txt')
| -rw-r--r-- | lib/lufa/Demos/Device/ClassDriver/MassStorage/MassStorage.txt | 100 |
1 files changed, 0 insertions, 100 deletions
diff --git a/lib/lufa/Demos/Device/ClassDriver/MassStorage/MassStorage.txt b/lib/lufa/Demos/Device/ClassDriver/MassStorage/MassStorage.txt deleted file mode 100644 index 5759efa6b..000000000 --- a/lib/lufa/Demos/Device/ClassDriver/MassStorage/MassStorage.txt +++ /dev/null @@ -1,100 +0,0 @@ -/** \file - * - * This file contains special DoxyGen information for the generation of the main page and other special - * documentation pages. It is not a project source file. - */ - -/** \mainpage Mass Storage Device Demo - * - * \section Sec_Compat Demo Compatibility: - * - * The following list indicates what microcontrollers are compatible with this demo. - * - * \li Series 7 USB AVRs (AT90USBxxx7) - * \li Series 6 USB AVRs (AT90USBxxx6) - * \li Series 4 USB AVRs (ATMEGAxxU4) - * \li Series 2 USB AVRs (AT90USBxx2, ATMEGAxxU2) - * \li Series AU XMEGA AVRs (ATXMEGAxxxAxU) - * \li Series B XMEGA AVRs (ATXMEGAxxxBx) - * \li Series C XMEGA AVRs (ATXMEGAxxxCx) - * - * \section Sec_Info USB Information: - * - * The following table gives a rundown of the USB utilization of this demo. - * - * <table> - * <tr> - * <td><b>USB Mode:</b></td> - * <td>Device</td> - * </tr> - * <tr> - * <td><b>USB Class:</b></td> - * <td>Mass Storage Device</td> - * </tr> - * <tr> - * <td><b>USB Subclass:</b></td> - * <td>Bulk-Only Transport</td> - * </tr> - * <tr> - * <td><b>Relevant Standards:</b></td> - * <td>USBIF Mass Storage Standard \n - * USB Bulk-Only Transport Standard \n - * SCSI Primary Commands Specification \n - * SCSI Block Commands Specification</td> - * </tr> - * <tr> - * <td><b>Supported USB Speeds:</b></td> - * <td>Full Speed Mode</td> - * </tr> - * </table> - * - * \section Sec_Description Project Description: - * - * Mass Storage device demonstration application. This gives a simple - * reference application for implementing a USB Mass Storage device using - * the basic USB UFI drivers in all modern OSes (i.e. no special drivers - * required). - * - * On start-up the system will automatically enumerate and function as an - * external mass storage device which may be formatted and used in the same - * manner as commercial USB Mass Storage devices. - * - * You will need to format the mass storage drive upon first run of this - * demonstration - as the device acts only as a data block transport between - * the host and the storage media, it does not matter what file system is used, - * as the data interpretation is performed by the host and not the USB device. - * - * This demo is not restricted to only a single LUN (logical disk); by changing - * the TOTAL_LUNS value in DataflashManager.h, any number of LUNs can be used - * (from 1 to 255), with each LUN being allocated an equal portion of the available - * Dataflash memory. - * - * The USB control endpoint is managed entirely by the library using endpoint - * interrupts, as the INTERRUPT_CONTROL_ENDPOINT option is enabled. This allows for - * the host to reset the Mass Storage device state during long transfers without - * the need for complicated polling logic. - * - * \section Sec_Options Project Options - * - * The following defines can be found in this demo, which can control the demo behaviour when defined, or changed in value. - * - * <table> - * <tr> - * <th><b>Define Name:</b></th> - * <th><b>Location:</b></th> - * <th><b>Description:</b></th> - * </tr> - * <tr> - * <td>TOTAL_LUNS</td> - * <td>AppConfig.h</td> - * <td>Total number of Logical Units (drives) in the device. The total device capacity is shared equally between each drive - - * this can be set to any positive non-zero amount.</td> - * </tr> - * <tr> - * <td>DISK_READ_ONLY</td> - * <td>AppConfig.h</td> - * <td>Configuration define, indicating if the disk should be write protected or not.</td> - * </tr> - * </table> - */ - |