diff options
Diffstat (limited to 'lib/lufa/LUFA/DoxygenPages/ConfiguringApps.txt')
| -rw-r--r-- | lib/lufa/LUFA/DoxygenPages/ConfiguringApps.txt | 157 |
1 files changed, 0 insertions, 157 deletions
diff --git a/lib/lufa/LUFA/DoxygenPages/ConfiguringApps.txt b/lib/lufa/LUFA/DoxygenPages/ConfiguringApps.txt deleted file mode 100644 index 15b660e92..000000000 --- a/lib/lufa/LUFA/DoxygenPages/ConfiguringApps.txt +++ /dev/null @@ -1,157 +0,0 @@ -/** \file - * - * This file contains special DoxyGen information for the generation of the main page and other special - * documentation pages. It is not a project source file. - */ - -/** \page Page_ConfiguringApps Configuring the Demos, Bootloaders and Projects - * - * If the target microcontroller model, architecture, clock speed, board or other settings are different from the current - * settings, they must be changed and the project recompiled from the source code before being programmed into the microcontroller. - * Most project configuration options are located in the <tt>makefile</tt> build script inside each LUFA application's folder, - * however some demo or application-specific configuration settings are located in one or more of the source files of the project. - * See each project's individual documentation for application-specific configuration values. - * - * Each project "makefile" contains all the script and configuration data required to compile each project. When opened with - * any regular basic text editor such as Notepad or WordPad (ensure that the save format is a pure ASCII text format) the - * build configuration settings may be altered. - * - * \see \ref Page_BuildSystem for information on the LUFA build system. - * - * \section Sec_ConfiguringApps_AppMakefileParams The Default Application Makefile Template - * - * Below is a copy of the default LUFA application makefile, which can be used as a template for each application. - * - * \verbinclude makefile_template - * - * Inside each makefile, a number of configuration variables are listed with the syntax "<VARIABLE NAME> = <VALUE>". For - * each application, the important standard variables which should be altered are: - * - * - <b>MCU</b>, the target processor model - * - <b>ARCH</b>, the target microcontroller architecture - * - <b>BOARD</b>, the target board hardware - * - <b>F_CPU</b>, the target CPU master clock frequency, after any prescaling - * - <b>F_USB</b>, the target raw input clock to the USB module of the processor - * - <b>OPTIMIZATION</b>, the level of optimization to compile with - * - <b>TARGET</b>, the name of the target output binary and other files - * - <b>SRC</b>, the list of source files to compile/assemble/link - * - <b>LUFA_PATH</b>, the path to the LUFA library core source code - * - <b>CC_FLAGS</b>, the common command line flags to pass to the C/C++ compiler, assembler and linker - * - <b>LD_FLAGS</b>, the command line flags to pass to the linker - * - * These values should be changed to reflect the build hardware. - * - * \subsection SSec_ConfiguringApps_MCU The MCU Parameter - * This parameter indicates the target microcontroller model for the compiled application. This should be set to the model of the target - * microcontroller (such as the AT90USB1287, or the ATMEGA32U4), in all lower-case (e.g. "at90usb1287"). Note that not all demos support all the - * microcontroller models and architectures, as they may make use of peripherals or modes only present in some devices. - * - * For supported processor models, see \ref Page_DeviceSupport. - * - * \subsection SSec_ConfiguringApps_ARCH The ARCH Parameter - * This parameter indicates the target microcontroller architecture the library is to be compiled for. Different microcontroller - * architectures require different source files to be compiled into the final binary, and so this option must be set to the correct - * architecture for the selected platform. - * - * For supported processor architectures, see \ref Page_DeviceSupport. - * - * \subsection SSec_ConfiguringApps_BOARD The BOARD Parameter - * This parameter indicates the target board hardware for the compiled application. Some LUFA library drivers are board-specific, - * such as the LED driver, and the library needs to know the layout of the target board. If you are using one of the board models listed - * on the main library page, change this parameter to the board name in all UPPER-case. - * - * If you are not using any board-specific drivers in the LUFA library, or you are using a custom board layout, change this to read - * "USER" (no quotes) instead of a standard board name. If the USER board type is selected and the application makes use of one or more - * board-specific hardware drivers inside the LUFA library, then the appropriate stub drives files should be copied from the \c /CodeTemplates/DriverStubs/ - * directory into a /Board/ folder inside the application directory, and the stub driver completed with the appropriate code to drive the - * custom board's hardware. - * - * For boards with built in hardware driver support within the LUFA library, see \ref Page_DeviceSupport. - * - * \subsection SSec_ConfiguringApps_F_CPU The F_CPU Parameter - * This parameter indicates the target microcontroller's main CPU clock frequency, in Hz. This is used by many libraries (and applications) for - * timing related purposes, and should reflect the actual CPU speed after any prescaling or adjustments are performed. - * - * \subsection SSec_ConfiguringApps_F_USB The F_USB Parameter - * This parameter indicates the raw input clock frequency to the USB module within the microcontroller in Hz. This may be very different on some platforms - * to the main CPU clock or other peripheral/bus clocks. - * - * \note On AVR8 platforms, this must be equal to \c 8000000 or \c 16000000. - * - * \note On XMEGA platforms, this must be equal to a multiple of 6000000 from \c 6000000 to \c 48000000. - * - * \note On UC3 platforms, this must be equal to a multiple of 12000000 from \c 12000000 to \c 48000000. - * - * \subsection SSec_ConfiguringApps_OPTIMIZATION The OPTIMIZATION Parameter - * This parameter indicates the level of optimization to use when compiling the application. This will allow you to compile with an optimization level - * supported by GCC, from <tt>0</tt> (no optimization) to <tt>3</tt> (fastest runtime optimization) or <tt>s</tt> (smallest size). - * - * \subsection SSec_ConfiguringApps_TARGET The TARGET Parameter - * This parameter indicates the application target name, which is used as the base filename for the build binary and debugging files. This will be the - * name of the output files once linked together into the final application, ready to load into the target. - * - * \subsection SSec_ConfiguringApps_SRC The SRC Parameter - * This parameter indicates the source files used to compile the application, as a list of C (<tt>*.c</tt>), C++ (<tt>*.cpp</tt>) and Assembly (<tt>*.S</tt>) files. Note that - * all assembly files must end in a <b>capital</b> .S extension, as lowercase .s files are reserved for GCC intermediate files. - * - * \subsection SSec_ConfiguringApps_LUFA_PATH The LUFA_PATH Parameter - * As each LUFA program requires the LUFA library source code to compile correctly, the application must know where the LUFA library is located. This - * value specifies the path to the LUFA library core. This path may be relative or absolute, however note than even under Windows based systems the - * forward-slash (/) path separator must be used. - * - * \subsection SSec_ConfiguringApps_CC_FLAGS The CC_FLAGS Parameter - * This parameter lists the compiler flags passed to the C/C++ compiler, the assembler and the linker. These are used as-is directly to GCC and thus - * must match GCC's command line options as given in the GCC manual. This variable may be used to define tokens directly on the command line, enable or - * disable warnings, adjust the target-specific tuning parameters or other options. - * - * \subsection SSec_ConfiguringApps_LD_FLAGS The LD_FLAGS Parameter - * This parameter lists the linker flags passed exclusively to the linker. These are used as-is directly to GCC and thus must match GCC's command line - * linker options as given in the GCC manual. This variable may be used to create or relocate custom data sections, or enable linker specific behaviors. - * - * - * \section Sec_ExampleAppConfig Example Application Makefile Configurations - * Below is an example makefile for an AVR8 based AT90USB1287 running at 8MHz, to compile a program called "MyApplication": - * \verbatim - MCU = at90usb1287 - ARCH = AVR8 - BOARD = NONE - F_CPU = 8000000 - F_USB = $(F_CPU) - OPTIMIZATION = s - TARGET = MyApplication - SRC = MyApplication.c Descriptors.c $(LUFA_SRC_USB) $(LUFA_SRC_USBCLASS) - LUFA_PATH = ../../../../LUFA - CC_FLAGS = -DUSE_LUFA_CONFIG_HEADER -IConfig/ - LD_FLAGS = - \endverbatim - * - * Below is an example makefile for an XMEGA based ATXMEGA128A1U running at 32MHz, to compile a program called "MyApplication": - * \verbatim - MCU = atxmega128a1u - ARCH = XMEGA - BOARD = NONE - F_CPU = 32000000 - F_USB = 48000000 - OPTIMIZATION = s - TARGET = MyApplication - SRC = MyApplication.c Descriptors.c $(LUFA_SRC_USB) $(LUFA_SRC_USBCLASS) - LUFA_PATH = ../../../../LUFA - CC_FLAGS = -DUSE_LUFA_CONFIG_HEADER -IConfig/ - LD_FLAGS = - \endverbatim - * - * Below is an example makefile for a UC3 based AT32UC3A0512 running at 50MHz, to compile a program called "MyApplication": - * \verbatim - MCU = uc3a0512 - ARCH = UC3 - BOARD = NONE - F_CPU = 50000000 - F_USB = 48000000 - OPTIMIZATION = s - TARGET = MyApplication - SRC = MyApplication.c Descriptors.c $(LUFA_SRC_USB) $(LUFA_SRC_USBCLASS) - LUFA_PATH = ../../../../LUFA - CC_FLAGS = -DUSE_LUFA_CONFIG_HEADER -IConfig/ - LD_FLAGS = - \endverbatim - */ |