diff options
Diffstat (limited to 'lib/lufa/Projects/AVRISP-MKII/AVRISP-MKII.txt')
| -rw-r--r-- | lib/lufa/Projects/AVRISP-MKII/AVRISP-MKII.txt | 346 |
1 files changed, 0 insertions, 346 deletions
diff --git a/lib/lufa/Projects/AVRISP-MKII/AVRISP-MKII.txt b/lib/lufa/Projects/AVRISP-MKII/AVRISP-MKII.txt deleted file mode 100644 index 76d612ec0..000000000 --- a/lib/lufa/Projects/AVRISP-MKII/AVRISP-MKII.txt +++ /dev/null @@ -1,346 +0,0 @@ -/** \file - * - * This file contains special DoxyGen information for the generation of the main page and other special - * documentation pages. It is not a project source file. - */ - -/** \mainpage AVRISP MKII Programmer Project - * - * \section Sec_Compat Project Compatibility - * - * The following list indicates what microcontrollers are compatible with this project. - * - * \li Series 7 USB AVRs (AT90USBxxx7) - * \li Series 6 USB AVRs (AT90USBxxx6) - * \li Series 4 USB AVRs (ATMEGAxxU4) - * \li Series 2 USB AVRs (AT90USBxx2, ATMEGAxxU2) - <i>8KB versions with reduced features only</i> - * - * \section Sec_Info USB Information - * - * The following table gives a rundown of the USB utilization of this project. - * - * <table> - * <tr> - * <td><b>USB Mode:</b></td> - * <td>Device</td> - * </tr> - * <tr> - * <td><b>USB Class:</b></td> - * <td>Vendor Specific Class</td> - * </tr> - * <tr> - * <td><b>USB Subclass:</b></td> - * <td>N/A</td> - * </tr> - * <tr> - * <td><b>Relevant Standards:</b></td> - * <td>Atmel AVRISP MKII Protocol Specification</td> - * </tr> - * <tr> - * <td><b>Supported USB Speeds:</b></td> - * <td>Full Speed Mode</td> - * </tr> - * </table> - * - * \section Sec_Description Project Description - * - * Firmware for an Atmel Studio compatible AVRISP-MKII clone programmer. This project will enable the USB - * AVR series of microcontrollers to act as a clone of the official Atmel AVRISP-MKII programmer, usable within - * Atmel Studio or with any software capable of driving a real Atmel AVRISP-MKII programmer. In its most - * basic form, it allows for the programming of AVR TINY, MEGA and XMEGA devices at the programmer's VCC voltage from - * within Atmel Studio with no special hardware other than the USB AVR and the parts needed for the USB - * interface. If the user desires, more advanced circuits incorporating level conversion can be made to allow for the - * programming of target AVRs running at a different voltage to the programmer. - * - * This device spoofs Atmel's official AVRISP-MKII device PID so that it remains compatible with Atmel's AVRISP-MKII - * drivers. It is currently tested working under the following configurations: - * - * - <b>Windows:</b> Atmel Studio 7, with alternative driver - * - <b>Windows:</b> AVRDUDE 6.2, with alternative driver - * - <b>Linux:</b> AVRDUDE 6.1 - * - * <b>Note that this clone requires a libUSB based driver under Windows,</b> due to an incompatible change in the official - * Jungo based driver. The alternative driver given here will function with both real and clone AVRISP devices in Atmel - * Studio 7 onwards under Windows - and as a bonus, also provides AVRDude access to the programmer. - * - * As of Atmel Studio version 7.0.1417 the legacy Jungo driver has been deprecated in favor of an official libUSB based - * driver, making the driver packaged here superfluous. Use the driver packaged here only if you are still using an earlier - * Atmel Studio 7 build, otherwise the official Atmel libUSB driver should be used. - * - * Note that this design currently has the following limitations: - * - No reversed/shorted target connector detection and notification - * - A separate header is required for each of the ISP, PDI and TPI programming protocols that the user wishes to use - * - * On AVR models with an ADC converter, the USB AVR's AVCC pin should be tied to 5V (e.g. VBUS) and the - * \c VTARGET_ADC_CHANNEL token should be set to an appropriate ADC channel number in the project makefile for VTARGET - * detection to operate correctly. On models without an ADC converter, VTARGET will report a fixed 3.3V level at all times - * which should allow the programmer to remain compatible at the protocol level with all AVR devices. - * - * While this application can be compiled for USB AVRs with as little as 8KB of FLASH, for full functionality 16KB or more - * of FLASH is required. On 8KB devices, ISP or PDI/TPI protocol programming support can be disabled to reduce program size. - * - * \section Sec_KnownIssues Known Issues: - * - * \par XMEGA EEPROM programming fails in some cases. - * Several users have reported that XMEGA EEPROM programming fails unless the chip is erased first. If a non-blank EEPROM - * is present, writing further EEPROM data causes corruption. - * <a href="https://github.com/abcminiuser/lufa/issues/25">LUFA issue tracker entry</a>. - * - * \section Sec_Installation Installation - * The programmer supports multiple platforms, both Windows and Linux. - * - * \subsection SSec_LinuxInstallation Linux Installation - * On Linux systems, the programmer should be usable out of the box with no special setup other than (on some systems) - * editing of the system permissions to allow the programmer to be used from a non-elevated (root) context. The programmer - * is compatible with the free open source AVRDude programming software project. - * - * \subsection SSec_WindowsInstallation Windows Installation - * On Windows systems, due to an unfortunate limitation of the USB AVR devices and the Atmel Studio platform, the programmer - * requires an alternative libUSB based driver. Uninstall the existing Jungo driver for the device (if installed) and replace - * it with the driver that ships with this project, to enable access to the programmer in Atmel Studio and AVRDUDE. - * - * \section Sec_ISP ISP Connections - * Connections to the device for SPI programming (when enabled): - * - * <table> - * <tr> - * <th><b>Programmer Pin:</b></th> - * <th><b>Target Device Pin:</b></th> - * <th><b>ISP 6 Pin Layout:</b></th> - * </tr> - * <tr> - * <td>MISO</td> - * <td>PDO</td> - * <td>1</td> - * </tr> - * <tr> - * <td>ADCx <b><sup>1</sup></b></td> - * <td>VTARGET</td> - * <td>2</td> - * </tr> - * <tr> - * <td>SCLK</td> - * <td>SCLK</td> - * <td>3</td> - * </tr> - * <tr> - * <td>MOSI</td> - * <td>PDI</td> - * <td>4</td> - * </tr> - * <tr> - * <td>PORTx.y <b><sup>2</sup></b></td> - * <td>/RESET</td> - * <td>5</td> - * </tr> - * <tr> - * <td>GND</td> - * <td>GND</td> - * <td>6</td> - * </tr> - * </table> - * - * In addition, the AVR's OCR1A pin will generate a 4MHz clock, to act as an external rescue device clock if the - * fuses have been mis-set. To use the recovery clock, connect the OCR1A pin of the USB AVR to the target AVR's - * XTAL1 pin, and set the ISP programming speed to 125KHz (note: other ISP speeds will not work correctly). - * - * <b><sup>1</sup></b> <i>Optional, see \ref Sec_Options section - for USB AVRs with ADC modules only</i> \n - * <b><sup>2</sup></b> <i>See AUX line related tokens in the \ref Sec_Options section</i> - * - * \section Sec_PDI PDI Connections - * Connections to the device for PDI programming (when enabled): - * - * <table> - * <tr> - * <th><b>Programmer Pin:</b></th> - * <th><b>Target Device Pin:</b></th> - * <th><b>PDI 6 Pin Layout:</b></th> - * </tr> - * <tr> - * <td>Tx/Rx <b><sup>2</sup></b></td> - * <td>DATA</td> - * <td>1</td> - * </tr> - * <tr> - * <td>ADCx <b><sup>1</sup></b></td> - * <td>VTARGET</td> - * <td>2</td> - * </tr> - * <tr> - * <td>N/A</td> - * <td>N/A</td> - * <td>3</td> - * </tr> - * <tr> - * <td>N/A</td> - * <td>N/A</td> - * <td>4</td> - * </tr> - * <tr> - * <td>XCK</td> - * <td>CLOCK</td> - * <td>5</td> - * </tr> - * <tr> - * <td>GND</td> - * <td>GND</td> - * <td>6</td> - * </tr> - * </table> - * - * <b><sup>1</sup></b> <i>Optional, see \ref Sec_Options section - for USB AVRs with ADC modules only</i> \n - * <b><sup>2</sup></b> <i>The AVR's Tx and Rx become the DATA line when connected together via a pair of 220 ohm resistors</i> \n - * - * \section Sec_TPI TPI Connections - * Connections to the device for TPI programming (when enabled): - * - * <table> - * <tr> - * <th><b>Programmer Pin:</b></th> - * <th><b>Target Device Pin:</b></th> - * <th><b>TPI 6 Pin Layout:</b></th> - * </tr> - * <tr> - * <td>Tx/Rx <b><sup>2</sup></b></td> - * <td>DATA</td> - * <td>1</td> - * </tr> - * <tr> - * <td>ADCx <b><sup>1</sup></b></td> - * <td>VTARGET</td> - * <td>2</td> - * </tr> - * <tr> - * <td>XCK <b><sup>2</sup></b></td> - * <td>CLOCK</td> - * <td>3</td> - * </tr> - * <tr> - * <td>N/A</td> - * <td>N/A</td> - * <td>4</td> - * </tr> - * <tr> - * <td>PORTx.y <b><sup>3</sup></b></td> - * <td>/RESET</td> - * <td>5</td> - * </tr> - * <tr> - * <td>GND</td> - * <td>GND</td> - * <td>6</td> - * </tr> - * </table> - * - * <b><sup>1</sup></b> <i>Optional, see \ref Sec_Options section - for USB AVRs with ADC modules only</i> \n - * <b><sup>2</sup></b> <i>The AVR's Tx and Rx become the DATA line when connected together via a pair of 220 ohm resistors</i> \n - * <b><sup>3</sup></b> <i>See AUX line related tokens in the \ref Sec_Options section</i> - * - * \section Sec_Options Project Options - * - * The following defines can be found in this project, which can control the project behaviour when defined, or changed in value. - * - * <table> - * <tr> - * <th><b>Define Name:</b></th> - * <th><b>Location:</b></th> - * <th><b>Description:</b></th> - * </tr> - * <tr> - * <td>AUX_LINE_PORT</td> - * <td>AppConfig.h</td> - * <td>PORT register for the programmer's AUX target line. The use of this line varies between the programming protocols, - * but is generally used for the target's /RESET line. - * \n \n <i>Ignored when compiled for the XPLAIN board.</i></td> - * </tr> - * <tr> - * <td>AUX_LINE_PIN</td> - * <td>AppConfig.h</td> - * <td>PIN register for the programmer's AUX target line. The use of this line varies between the programming protocols, - * but is generally used for the target's /RESET line. - * \n \n <i>Ignored when compiled for the XPLAIN board.</i></td> - * </tr> - * <tr> - * <td>AUX_LINE_DDR</td> - * <td>AppConfig.h</td> - * <td>DDR register for the programmer's AUX target line. The use of this line varies between the programming protocols, - * but is generally used for the target's /RESET line. - * \n \n <i>Ignored when compiled for the XPLAIN board.</i></td> - * </tr> - * <tr> - * <td>AUX_LINE_MASK</td> - * <td>AppConfig.h</td> - * <td>Mask for the programmer's AUX target line. The use of this line varies between the programming protocols, - * but is generally used for the target's /RESET line. <b>Must not be the AVR's /SS pin</b>. - * \n \n <i>Ignored when compiled for the XPLAIN board.</i></td> - * </tr> - * <tr> - * <td>VTARGET_ADC_CHANNEL</td> - * <td>AppConfig.h</td> - * <td>ADC channel number (on supported AVRs) to use for VTARGET level detection, if NO_VTARGET_DETECT is not defined. - * \n \n <i>Ignored when compiled for targets lacking an ADC.</i></td> - * </tr> - * <tr> - * <td>ENABLE_ISP_PROTOCOL</td> - * <td>AppConfig.h</td> - * <td>Define to enable SPI programming protocol support. - * \n \n <i>Ignored when compiled for the XPLAIN board.</i></td> - * </tr> - * <tr> - * <td>ENABLE_XPROG_PROTOCOL</td> - * <td>AppConfig.h</td> - * <td>Define to enable PDI and TPI programming protocol support. - * \n \n <i>Ignored when compiled for the XPLAIN board.</i></td> - * </tr> - * <tr> - * <td>NO_VTARGET_DETECT</td> - * <td>AppConfig.h</td> - * <td>Define to disable VTARGET sampling and reporting on AVR models with an ADC converter. This will cause the programmer - * to report a fixed 3.3V target voltage to the host regardless of the real target voltage. - * \n \n <i>Ignored when compiled for targets lacking an ADC.</i></td> - * </tr> - * <tr> - * <td>VTARGET_REF_VOLTS</td> - * <td>AppConfig.h</td> - * <td>Indicates the programmer AVR's AVCC reference voltage when measuring the target's supply voltage. Note that the supply - * voltage should never exceed the reference voltage on the programmer AVR without some form of protection to prevent damage - * to the ADC. - * \n \n <i>Ignored when compiled for targets lacking an ADC, or when NO_VTARGET_DETECT is defined.</i></td> - * </tr> - * <tr> - * <td>VTARGET_USE_INTERNAL_REF</td> - * <td>AppConfig.h</td> - * <td>Selects the internal 2.56V ADC reference voltage, instead of using the AVR's VREF pin. When enabled, this option will - * override the VTARGET_REF_VOLTS configuration option. - * \n \n <i>Ignored when compiled for targets lacking an ADC, or when NO_VTARGET_DETECT is defined.</i></td> - * </tr> - * <tr> - * <td>VTARGET_SCALE_FACTOR</td> - * <td>AppConfig.h</td> - * <td>Indicates the target's supply voltage scale factor when applied to the ADC. A simple resistive divider can be used on the - * ADC pin for measuring the target's supply voltage, so that voltages above the programmer AVR's AVCC reference voltage can be - * measured. This should be the reciprocal of the division performed - e.g. if the VTARGET voltage is halved, this should be set - * to 2. - * \n \n <i>Ignored when compiled for targets lacking an ADC, or when NO_VTARGET_DETECT is defined.</i></td> - * </tr> - * <tr> - * <td>XCK_RESCUE_CLOCK_ENABLE</td> - * <td>AppConfig.h</td> - * <td>Define to move the ISP rescue clock to the AVR's XCK pin instead of the OCR1A output pin. This is useful for existing programming - * hardware that does not expose the OCR1A pin of the AVR, but <i>may</i> cause some issues with PDI programming mode.</td> - * </tr> - * <tr> - * <td>INVERTED_ISP_MISO</td> - * <td>AppConfig.h</td> - * <td>Define to invert the received data on the ISP MISO line. This is sometimes needed depending on the level translation hardware used, - * if the translator hardware inverts the received logic level.</td> - * </tr> - * <tr> - * <td>FIRMWARE_VERSION_MINOR</td> - * <td>AppConfig.h</td> - * <td>Define to set the minor firmware revision nunber reported to the host on request. By default this will use a firmware version compatible - * with the latest Atmel IDE version, however if desired the reported minor value can be adjusted here.</td> - * </tr> - * </table> - */ - |