1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
|
# PR checklists
This is a non-exhaustive checklist of what the QMK collaborators will be checking when reviewing submitted PRs.
If there are any inconsistencies with these recommendations, you're best off [creating an issue](https://github.com/qmk/qmk_firmware/issues/new) against this document, or getting in touch with a QMK Collaborator on Discord.
## General PRs
- PR should be submitted using a non-`master` branch on the source repository
- This does not mean you target a different branch for your PR, rather that you're not working out of your own master branch
- If submitter _does_ use their own `master` branch, they'll be given a link to the ["how to git"](https://docs.qmk.fm/#/newbs_git_using_your_master_branch) page after merging -- (end of this document will contain the contents of the message)
- Newly-added directories and filenames must be lowercase
- This rule may be relaxed if upstream sources originally had uppercase characters (e.g. ChibiOS, or imported files from other repositories etc.)
- If there is enough justification (i.e. consistency with existing core files etc.) this can be relaxed
- a board designer naming their keyboard with uppercase letters is not enough justification
- Valid license headers on all `*.c` and `*.h` source files
- GPL2/GPL3 recommended for consistency
- Other licenses are permitted, however they must be GPL-compatible and must allow for redistribution. Using a different license will almost certainly delay a PR getting merged.
- QMK codebase "best practices" followed
- This is not an exhaustive list, and will likely get amended as time goes by
- `#pragma once` instead of `#ifndef` include guards in header files
- No "old-school" GPIO/I2C/SPI functions used -- must use QMK abstractions unless justifiable (and laziness is not valid justification)
- Timing abstractions should be followed too:
- `wait_ms()` instead of `_delay_ms()` (remove `#include <util/delay.h>` too)
- `timer_read()` and `timer_read32()` etc. -- see [timer.h](https://github.com/qmk/qmk_firmware/blob/master/tmk_core/common/timer.h) for the timing APIs
- If you think a new abstraction is useful, you're encouraged to:
- prototype it in your own keyboard until it's feature-complete
- discuss it with QMK Collaborators on Discord
- refactor it as a separate core change
- remove your specific copy in your board
## Core PRs
- Must now target `develop` branch, which will subsequently be merged back to `master` on the breaking changes timeline
- Other notes TBD
- Core is a lot more subjective given the breadth of posted changes
## Keyboard PRs
Closed PRs (for inspiration, previous sets of review comments will help you eliminate ping-pong of your own reviews):
https://github.com/qmk/qmk_firmware/pulls?q=is%3Apr+is%3Aclosed+label%3Akeyboard
- `info.json`
- valid URL
- valid maintainer
- displays correctly in Configurator (press Ctrl+Shift+I to preview local file, turn on fast input to verify ordering)
- `readme.md`
- standard template should be present
- flash command has `:flash` at end
- valid hardware availability link (unless handwired) -- private groupbuys are okay, but one-off prototypes will be questioned. If open-source, a link to files should be provided.
- `rules.mk`
- removed `MIDI_ENABLE`, `FAUXCLICKY_ENABLE` and `HD44780_ENABLE`
- modified `# Enable Bluetooth with the Adafruit EZ-Key HID` -> `# Enable Bluetooth`
- No `(-/+size)` comments related to enabling features
- Remove the list of alternate bootloaders if one has been specified
- No re-definitions of the default MCU parameters if same value, when compared to the equivalent MCU in [mcu_selection.mk](https://github.com/qmk/qmk_firmware/blob/master/quantum/mcu_selection.mk)
- keyboard `config.h`
- don't repeat `MANUFACTURER` in the `PRODUCT` value
- no `#define DESCRIPTION`
- no Magic Key Options, MIDI Options or HD44780 configuration
- user preference configurable `#define`s need to be moved to keymap `config.h`
- "`DEBOUNCE`" instead of "`DEBOUNCING_DELAY`"
- bare minimum required code for a board to boot into QMK should be present
- initialisation code for the matrix and critical devices
- mirroring existing functionality of a commercial board (like custom keycodes and special animations etc.) should be handled through non-`default` keymaps
- `keyboard.c`
- empty `xxxx_xxxx_kb()` or other weak-defined default implemented functions removed
- commented-out functions removed too
- `matrix_init_board()` etc. migrated to `keyboard_pre_init_kb()`, see: [keyboard_pre_init*](https://docs.qmk.fm/#/custom_quantum_functions?id=keyboard_pre_init_-function-documentation)
- prefer `CUSTOM_MATRIX = lite` if custom matrix used, allows for standard debounce, see [custom matrix 'lite'](https://docs.qmk.fm/#/custom_matrix?id=lite)
- `keyboard.h`
- `#include "quantum.h"` appears at the top
- `LAYOUT` macros should use standard definitions if applicable
- Use the Community Layout macro names where they apply (preferred above `LAYOUT`/`LAYOUT_all`)
- keymap `config.h`
- no duplication of `rules.mk` or `config.h` from keyboard
- `keymaps/default/keymap.c`
- `QMKBEST`/`QMKURL` removed (sheesh)
- If using `MO(_LOWER)` and `MO(_RAISE)` keycodes or equivalent, and the keymap has an adjust layer when holding both keys -- if the keymap has no "direct-to-adjust" keycode (such as `MO(_ADJUST)`) then you should prefer to write...
```
layer_state_t layer_state_set_user(layer_state_t state) {
return update_tri_layer_state(state, _LOWER, _RAISE, _ADJUST);
}
```
...instead of manually handling `layer_on()`, `update_tri_layer()` inside the keymap's `process_record_user()`.
- default (and via) keymaps should be "pristine"
- bare minimum to be used as a "clean slate" for another user to develop their own user-specific keymap
- standard layouts preferred in these keymaps, if possible
- submitters can have a personal (or bells-and-whistles) keymap showcasing capabilities in the same PR but it shouldn't be embedded in the 'default' keymap
- submitters can also have a "manufacturer-matching" keymap that mirrors existing functionality of the commercial product, if porting an existing board
Also, specific to ChibiOS:
- **Strong** preference to using existing ChibiOS board definitions.
- A lot of the time, an equivalent Nucleo board can be used with a different flash size or slightly different model in the same family
- Example: For an STM32L082KZ, given the similarity to an STM32L073RZ, you can use `BOARD = ST_NUCLEO64_L073RZ` in rules.mk
- QMK is migrating to not having custom board definitions if at all possible, due to the ongoing maintenance burden when upgrading ChibiOS
- If a board definition is unavoidable, `board.c` must have a standard `__early_init()` (as per normal ChibiOS board defs) and an empty `boardInit()`:
- see Arm/ChibiOS [early initialization](https://docs.qmk.fm/#/platformdev_chibios_earlyinit?id=board-init)
- `__early_init()` should be replaced by either `early_hardware_init_pre()` or `early_hardware_init_post()` as appropriate
- `boardInit()` should be migrated to `board_init()`
## Keymap PRs
- `#include QMK_KEYBOARD_H` preferred to including specific board files
- Prefer layer `enum`s to `#define`s
- Require custom keycode `enum`s to `#define`s, first entry must have ` = SAFE_RANGE`
- Terminating backslash (`\`) in lines of LAYOUT macro parameters is superfluous
- Some care with spacing (e.g., alignment on commas or first char of keycodes) makes for a much nicer-looking keymap
---
## Notes
For when people use their own `master` branch, post this after merge:
```
For future reference, we recommend against committing to your `master` branch as you've done here, because pull requests from modified `master` branches can make it more difficult to keep your QMK fork updated. It is highly recommended for QMK development – regardless of what is being done or where – to keep your master updated, but **NEVER** commit to it. Instead, do all your changes in a branch (branches are basically free in Git) and issue PRs from your branches when you're developing.
There are instructions on how to keep your fork updated here:
[**Best Practices: Your Fork's Master: Update Often, Commit Never**](https://docs.qmk.fm/#/newbs_git_using_your_master_branch)
[Fixing Your Branch](https://docs.qmk.fm/#/newbs_git_resynchronize_a_branch) will walk you through fixing up your `master` branch moving forward. If you need any help with this just ask.
Thanks for contributing!
```
|
