blob: 307a17e3882455aee62799e32b554b71991c4932 (
plain) (
blame)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
|
/*
ChibiOS - Copyright (C) 2006..2016 Giovanni Di Sirio
Licensed under the Apache License, Version 2.0 (the "License");
you may not use this file except in compliance with the License.
You may obtain a copy of the License at
http://www.apache.org/licenses/LICENSE-2.0
Unless required by applicable law or agreed to in writing, software
distributed under the License is distributed on an "AS IS" BASIS,
WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
See the License for the specific language governing permissions and
limitations under the License.
*/
#ifndef _BOARD_H_
#define _BOARD_H_
/*
* Board identifier.
*/
#define BOARD_JM60
#define BOARD_NAME "ErgoDox STM32 Keyboard"
/*
* Board frequencies.
*/
#define STM32_LSECLK 0
#define STM32_HSECLK 8000000
/*
* MCU type, supported types are defined in ./os/hal/platforms/hal_lld.h.
*
* Only xB (128KB Flash) is defined, but it's identical to the
* x8 version (64KB Flash) except for the Flash region size in the
* linker script. For x8 parts use xB here and change to the x8 linker
* script in the project Makefile.
*/
#define STM32F103xB
/*
* IO pins assignments
*
* numbering is sorted by onboard/connectors, as from the schematics in
* http://www.vcc-gnd.com/read.php?tid=369
*/
/* on-board */
#define GPIOA_USBDM 11 // pin 8
#define GPIOA_USBDP 12 // pin 9
#define GPIOC_OSC32_IN 14
#define GPIOC_OSC32_OUT 15
/*
* I/O ports initial setup, this configuration is established soon after reset
* in the initialization code.
*
* The digits have the following meaning:
* 0 - Analog input.
* 1 - Push Pull output 10MHz.
* 2 - Push Pull output 2MHz.
* 3 - Push Pull output 50MHz.
* 4 - Digital input.
* 5 - Open Drain output 10MHz.
* 6 - Open Drain output 2MHz.
* 7 - Open Drain output 50MHz.
* 8 - Digital input with PullUp or PullDown resistor depending on ODR.
* 9 - Alternate Push Pull output 10MHz.
* A - Alternate Push Pull output 2MHz.
* B - Alternate Push Pull output 50MHz.
* C - Reserved.
* D - Alternate Open Drain output 10MHz.
* E - Alternate Open Drain output 2MHz.
* F - Alternate Open Drain output 50MHz.
* Please refer to the STM32 Reference Manual for details.
*/
/*
* Port A setup.
* Everything input with pull-up except:
*/
#define VAL_GPIOACRL 0x88888888 /* PA7...PA0 */
#define VAL_GPIOACRH 0x88888888 /* PA15...PA8 */
#define VAL_GPIOAODR 0xFFFFFFFF
/*
* Port B setup.
* Everything input with pull-up except:
*/
#define VAL_GPIOBCRL 0x88888888 /* PB7...PB0 */
#define VAL_GPIOBCRH 0x88888888 /* PB15...PB8 */
#define VAL_GPIOBODR 0xFFFFFFFF
/*
* Port C setup.
* Everything input with pull-up except:
*/
#define VAL_GPIOCCRL 0x88888888 /* PC7...PC0 */
#define VAL_GPIOCCRH 0x88888888 /* PC15...PC8 */
#define VAL_GPIOCODR 0xFFFFFFFF
/*
* Port D setup.
* Everything input with pull-up except:
* PD0 - Normal input (XTAL).
* PD1 - Normal input (XTAL).
*/
#define VAL_GPIODCRL 0x88888844 /* PD7...PD0 */
#define VAL_GPIODCRH 0x88888888 /* PD15...PD8 */
#define VAL_GPIODODR 0xFFFFFFFF
/*
* Port E setup.
* Everything input with pull-up except:
*/
#define VAL_GPIOECRL 0x88888888 /* PE7...PE0 */
#define VAL_GPIOECRH 0x88888888 /* PE15...PE8 */
#define VAL_GPIOEODR 0xFFFFFFFF
/*
* USB bus activation macro, required by the USB driver.
*/
#define usb_lld_connect_bus(usbp) /* always connected */
/*
* USB bus de-activation macro, required by the USB driver.
*/
#define usb_lld_disconnect_bus(usbp) /* always connected */
#if !defined(_FROM_ASM_)
#ifdef __cplusplus
extern "C" {
#endif
void boardInit(void);
#ifdef __cplusplus
}
#endif
#endif /* _FROM_ASM_ */
#endif /* _BOARD_H_ */
|
